TOA P-924MK2 UL Manuel utilisateur
- Catégorie
- Amplificateurs audio
- Taper
- Manuel utilisateur
OPERATING INSTRUCTIONS
900 series
POWER AMPLIFIERS
P-906MK2
P-912MK2
P-924MK2
SIGNAL NORMAL
PROTECT
MASTER
ON
OFF
PEAK
POWER
SIGNAL NORMAL
PROTECT
MASTER
ON
OFF
PEAK
POWER
P-906MK2
P-912MK2
P-924MK2
Thank you for purchasing TOA's 900 Series
Power Amplifier.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS ..... 2
2. SAFETY PRECAUTIONS ............................ 3
3. GENERAL DESCRIPTION .......................... 5
4. FEATURES .................................................. 5
5. NOMENCLATURE AND FUNCTIONS
Front ............................................................. 6
Rear ............................................................. 7
6. INSTALLATION AND CONNECTIONS
6.1. Input Connections ................................. 8
6.2. Speaker Connections ............................ 9
7.
RACK MOUNTING BRACKET ATTACHMENT
... 11
8. OPERATION .............................................. 12
9. VOLUME CONTROL COVER ................... 12
10. DIMENSIONAL DIAGRAMS
10.1. P-906MK2, P-912MK2 ...................... 13
10.2. P-924MK2 ......................................... 14
11. SPECIFICATIONS
11.1. P-906MK2, P-912MK2 ...................... 15
11.2. P-924MK2 ......................................... 16
2
1. IMPORTANT SAFETY INSTRUCTIONS
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
INSTRUCTIONS ESSENTIELLES POUR LA SÉCURITÉ
• Lire ces instructions.
• Conserver ces instructions pour référence ultérieure.
• Respecter tous les avertissements.
• Suivre toutes les instructions.
• Ne pas utiliser cet appareil à proximité d'eau.
• Nettoyer uniquement à l'aide d'un chiffon sec.
• Ne pas obstruer les orifices de ventilation. Installer conformément aux instructions du fabricant.
• Ne pas installer à proximité de sources de chaleur telles que des radiateurs, des registres thermiques, des
chaudières ou d'autres appareils (notamment des amplificateurs) produisant de la chaleur.
• Ne pas contourner la fonction de sécurité de la fiche polarisée ou de mise à la terre. Une fiche polarisée est
équipée de deux broches, dont l'une est plus large que l'autre. Une fiche de mise à la terre est équipée de
deux broches et d'une troisième pour la mise à la terre. Cette dernière, la plus large, est prévue à des fins
de sécurité. Si la fiche fournie ne peut être insérée dans la prise électrique souhaitée, consulter un
électricien pour faire remplacer cette dernière.
• Protéger le cordon d'alimentation pour éviter qu'il ne soit piétiné ou pincé, notamment au niveau des fiches,
des prises de courant ou de son point de sortie de l'appareil.
• Utiliser uniquement les accessoires spécifiés par le fabricant.
• Utiliser uniquement avec le chariot, support, trépied, la patte de montage ou la table
spécifiés par le fabricant ou vendus avec l'appareil. En cas d'utilisation d'un chariot,
manipuler la combinaison chariot/appareil pour éviter les blessures dues à un
renversement.
• Débrancher cet appareil pendant les orages ainsi que lorsqu'il reste inutilisé pendant une période prolongée.
• La maintenance de l'appareil doit être confiée à un technicien après-vente qualifié. Une maintenance s'avère
nécessaire si l'appareil est endommagé (au niveau du cordon d'alimentation ou de la fiche), a été mouillé
par un liquide, un objet est tombé à l'intérieur, s'il a été exposé à la pluie ou l'humidité, s'il ne fonctionne pas
normalement ou s'il est tombé.
3
2. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
When Installing the Unit
• Do not expose the unit to rain or an environment where it may be splashed by water or other liquids, as
doing so may result in fire or electric shock.
• Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is specified
may result in fire or electric shock.
• Do not cut, kink, otherwise damage nor modify the power supply cord. In addition, avoid using the power
cord in close proximity to heaters, and never place heavy objects -- including the unit itself -- on the power
cord, as doing so may result in fire or electric shock.
• Be sure to replace the unit's terminal cover after connection completion. Because high voltage is applied to
the speaker output terminals, never touch these terminals to avoid electric shock.
• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface.
Doing so may result in the unit falling down and causing personal injury and/or property damage.
• External wiring connected to the terminals marked with requires installation by an instructed person.
• The apparatus shall be connected to a mains socket outlet with a protective earthing connection.
• L'appareil doit être branché à une prise d'alimentation avec mise à la terre de protection.
• The socket-outlet shall be installed near the equipment and the plug shall be easily accessible.
• Use the optional Rack mounting bracket MB-25B (P-906MK2 and P-912MK2) or MB-35B (P-924MK2) when
mounting the unit in an equipment rack. Remove four M4 x 8 screws on both sides of the unit, and mount the
bracket there using the M4 x 16 screws (supplied with the bracket) instead.
When the Unit is in Use
• Should the following irregularity be found during use, immediately switch off the power, disconnect the power
supply plug from the AC outlet and contact your nearest TOA dealer. Make no further attempt to operate the
unit in this condition as this may cause fire or electric shock.
· If you detect smoke or a strange smell coming from the unit
· If water or any metallic object gets into the unit
· If the unit falls, or the unit case breaks
· If the power supply cord is damaged (exposure of the core, disconnection, etc.)
· If it is malfunctioning (no tone sounds.)
• To prevent a fire or electric shock, never open nor remove the unit case as there are high voltage
components inside the unit. Refer all servicing to your nearest TOA dealer.
• Do not place cups, bowls, or other containers of liquid or metallic objects on top of the unit. If they
accidentally spill into the unit, this may cause a fire or electric shock.
• Do not insert nor drop metallic objects or flammable materials in the ventilation slots of the unit's cover, as
this may result in fire or electric shock.
Indicates a potentially hazardous situation which, if mishandled,
could result in death or serious personal injury.
WARNING
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instruction in the literature accompanying the
appliance.
Le point d'exclamation à l'intérieur d'un triangle équilatéral avertit l'utilisateur de l'existence
d'instructions d'utilisation et d'entretien (réparation) dans la documentation fournie avec l'appareil.
4
When Installing the Unit
• Never plug in nor remove the power supply plug with wet hands, as doing so may cause electric shock.
• When unplugging the power supply cord, be sure to grasp the power supply plug; never pull on the cord
itself. Operating the unit with a damaged power supply cord may cause a fire or electric shock.
• When moving the unit, be sure to remove its power supply cord from the wall outlet. Moving the unit with the
power cord connected to the outlet may cause damage to the power cord, resulting in fire or electric shock.
When removing the power cord, be sure to hold its plug to pull.
• Do not block the ventilation slots in the unit's cover. Doing so may cause heat to build up inside the unit and
result in fire.
• Avoid installing the unit in humid or dusty locations, in locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or steam as doing otherwise may result in fire or electric
shock.
• To avoid electric shocks, be sure to unplug the unit's power supply cord when connecting speakers.
• Be sure to follow the instructions below when rack-mounting the unit. Failure to do so may cause a fire or
personal injury.
· Install the equipment rack on a stable, hard floor. Fix it with anchor bolts or take other arrangements to
prevent it from falling down.
· When connecting the unit's power cord to an AC outlet, use the AC outlet with current capacity allowable to
the unit.
· No rack-mounting screws are supplied with the unit. Separately prepare the appropriate screws for the
rack.
• Keep the amplifier over 10 cm (3.94") away
from objects that may obstruct air flow to
prevent the unit's internal temperature rise.
When the Unit is in Use
• Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal
injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage.
• Make sure that the volume control is set to minimum position before power is switched on. Loud noise
produced at high volume when power is switched on can impair hearing.
• Do not operate the unit for an extended period of time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate and result in a fire.
• If dust accumulates on the power supply plug or in the wall AC outlet, a fire may result. Clean it periodically.
In addition, insert the plug in the wall outlet securely.
• Switch off the power, and unplug the power supply plug from the AC outlet for safety purposes when
cleaning or leaving the unit unused for 10 days or more. Doing otherwise may cause a fire or electric shock.
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
L'appareil ne doit pas être exposé aux éclaboussures ou écoulements et tous objets remplis de liquide, tels
que vases, ne doivent pas être sur l’appareil.
ATTENTION
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Over 10 cm (3.94”) Over 10 cm (3.94”)
Over 10 cm
(3.94”)
L'éclair accompagné d'un symbole représentant une pointe de flèche à l'intérieur d'un triangle
équilatéral avertit l'utilisateur de la présence d'une "tension dangereuse" à l'intérieur de l'enceinte
du téléviseur, dont la magnitude peut être suffisante pour constituer un risque de choc électrique
pour les personnes.
5
3. GENERAL DESCRIPTION
TOA's P-906MK2 (rated output: 60 W), P-912MK2 (120 W), and P-924MK2 (240 W) Power Amplifiers feature
a high-impedance direct input terminal and an input port that permits the use of various optional plug-in
modules. The most appropriate plug-in module can be selected depending on applications.
The power amplifiers have a low-cut switch for a cutoff frequency of 60 Hz, and an input level switch for input
sensitivity of 0 dBV (1 V) or –20 dBV (100 mV). The speaker output terminals are designed to match 25 V or
70 V line and 4 Ω or 8 Ω speaker systems.
Each Power Amplifier can be mounted in an EIA equipment rack with the addition of the optional rack
mounting bracket MB-25B (P-906MK2 and P-912MK2) or MB-35B (P-924MK2). The optional perforated panel
PF-511 provides suitable ventilation, finished in black color to match the Power Amplifiers.
4. FEATURES
• A wide frequency response of 20 to 20,000 Hz (±1 dB)
• Low distortion and low noise level
• Usable a wide range of plug-in optional modules
• Built-in protection circuitry
• Input level switch (selectable 0 dBV or –20 dBV)
• Mountable in a standard 19" equipment rack (rack mounting bracket: optional)
6
900
SERIES AMPLIFIER P
–
924
MK
2
SIGNAL NORMAL
PROTECT
MASTER
ON
OFF
PEAK
POWER
900
SERIES AMPLIFIER P
–
906
MK
2
SIGNAL NORMAL
PROTECT
MASTER
ON
OFF
PEAK
POWER
3 4 5 6 7
2
1
3 4 5 6 7
2
1
• P-906MK2, P-912MK2
This figure represents the P-906MK2.
• P-924MK2
5. NOMENCLATURE AND FUNCTIONS
[Front]
1. Power switch [ ON / OFF]
Power is switched on and off with each depression
of this switch.
2. Power indicator [POWER] (Green)
Lights green when the Power switch (1) is
switched on.
3. Master volume control [MASTER]
Adjusts gain of input.
4. Protection indicator [PROTECT]
Lights red if the built-in protection circuit works.
This indicator remains lit for about 5 seconds after
the power has been switched on.
5. Signal indicator [SIGNAL] (Green)
Lights green when sound is output from the
speaker output terminals.
6. Normal indicator [NORMAL] (Yellow)
Lights yellow when the output sound volume is
appropriate.
7. Peak indicator [PEAK] (Red)
Lights red if input signals approach clipping level.
If steady lit, turn down the Input volume control
until the indicator flashes only intermittently.
7
HOT
ON
LOW
CUT
INPUT
LEVEL
OFF
0dB
– 20dB
COM
INPUT
DIRECT
4Ω 8Ω
70V
25V
COM
CLASS 2 WIRING
MAY BE USED.
INPUT
ON
OFF
0dBV
HOT
COM
–20dBV
LOW CUT
INPUT LEVEL
70V
25V
8Ω
COM
OT IN
4Ω
8 9
10 11 12
13 14 15
14 15
8 9
10 1112
• P-906MK2, P-912MK2
This figure represents the P-906MK2.
• P-924MK2
[Rear]
8. AC outlet (Unswitched)
Provides AC power to auxiliary equipment with
power consumption of less than 500 W.
9. Speaker output terminals
Connect speaker cables to these terminals.
10. Low-cut switch [LOW CUT ON/OFF]
Set this switch to the ON position to cut off
unnecessary low frequencies.
11. Direct input terminal [INPUT]
0 dBV (1 V) or –20 dBV (100 mV) switchable, 10
kΩ, unbalanced.
Connect the line output of the external
equipment directly to this terminal.
The Direct input terminal cannot be used
simultaneously with the Module input port.
12. Module input port
Accepts one of 900 series plug-in modules. For
the selection of the most appropriate module,
refer to Plug-in Module Instruction manual.
13. Impedance selector switch [DIRECT]
(P-906MK2, P-912MK2 only)
Placing the switch in the "8 Ω" position enables
transformer-balanced 25 V, 70 V, or low-
impedance (8 Ω) speaker connection. Placing it
in the "DIRECT 4 Ω" position enables only
unbalanced low-impedance speaker connection.
For the use of this switch, refer to p. 9, "Speaker
Connections."
14. AC power cord
Connect this cord to an AC wall outlet.
15. Input level switch [INPUT LEVEL]
Select the appropriate input level "0 dBV" (1 V)
or "–20 dBV" (100 mV) depending on the module
to be used or equipment to be connected to the
Direct input terminal (11).
Normally place the switch in the " 0 dBV" position
when using the unit as an incremental power
amplifier.
8
6. INSTALLATION AND CONNECTIONS
6.1. Input Connections
• Two types of input terminals are made available on the rear panel for input connections: Direct input terminal
and plug-in module port.
(1) Direct input terminal (HOT, COM)
0 dB (1 V) or –20 dBV (100 mV) switchable, 10 kΩ, unbalanced, 2P screw terminal.
Line output of the external equipment can be connected directly to this terminal.
(2) Plug-in module input
Select a desired 900 series plug-in module depending on applications.
Note: The Direct Input terminal cannot be used simultaneously with the Plug-in module input.
• Plug the module fully into the input port by sliding it along the upper and lower guide rails, then secure with 2
screws.
• When the Module input port is not used, be sure to cover it with the blank panel attached to the unit.
• Be sure to set the Input Level switch to the proper position depending on the output level of the module used
or the equipment connected to the Direct Input terminal.
• When using the unit in combination with a mixer preamplifier or as a booster amplifier, place Input Level
switch in the "0 dBV" (1 V) position.
• Be sure to switch off the unit's power when inserting or removing the module. Failure to do so may cause the
module to fail.
HO
T
O
N
LO
W
C
U
T
INP
U
T
LEVEL
O
F
F
0
d
B
–
2
0
d
B
CO
M
IN
P
UT
Amplifier
900 Series module (option)
or
Blank panel (accessory)
Machine screw M3 x 8
(accessory)
This figure represents the P-906MK2.
9
70V
25V
8Ω
COM
OT IN
4Ω
DIRECT
4Ω 8Ω
70V
25V
COM
• P-906MK2, P-912MK2
• P-924MK2
8 Ω
10.4 Ω (P-906MK2)
5.2 Ω (P-912MK2)
25 V line
83 Ω (P-906MK2)
41 Ω (P-912MK2)
70 V line
Step 1. Loosen the screw.
Step 2. Shift the impedance selector switch to "8 Ω" position.
Step 3. Retighten the screw.
8 Ω
Insert the jumper strip between 4 Ω (+) and "OT IN."
2.6 Ω
25 V line
21 Ω
70 V line
6.2. Speaker Connections
The unit has 25 V and 70 V outputs for constant voltage speaker system and low impedance output for 4 Ω or
8 Ω speaker loads. Two types of speaker output are available: transformer-balanced output and unbalanced
direct output, which can be selected by the impedance selector switch (P-906MK2 and P-912MK2 only) or the
jumper strip (P-924MK2 only) position.
Connect the speaker system to only one of the speaker outputs.
The speaker connection method differs with amplifier models and their applications.
Refer to the following connection diagrams described for each model.
Impedances indicated in the diagram mean total speaker load impedance.
6.2.1. Connection to 8 Ω, 25 V, or 70 V output (transformer-balanced output)
Step 1. Unscrew the terminal cover.
Step 2. Strip 10 mm (0.39") of insulative jacket from the end of the speaker cable,
as shown in the figure at right.
Step 3. Connect speaker cables to the speaker output terminals.
Step 4. Replace the terminal cover.
10 mm
(0.39”)
[Connection of speaker cable]
Note
It is highly recommended that the low-cut switch be placed in the CUT position to cut off unnecessary low
frequency. This is because the built-in transformer cannot produce low frequencies though the unit has flat
response even in low-frequency range.
Be sure to replace the terminal cover after connection completion.
Because high voltage is generated at the speaker output terminals,
never touch these terminals to avoid electric shock.
WARNING
The terminals marked with the symbol are hazardous live.
The external wiring to these terminals requires installation by an
instructed person.
WARNING
10
6.2.2. Connection to 4 Ω output (unbalanced direct output)
DIRECT
4Ω 8Ω
70V
25V
COM
70V
25V
8Ω
COM
OT IN
4Ω
• P-906MK2, P-912MK2
• P-924MK2
4 Ω
4 Ω
Step 1. Loosen the screw.
Step 2. Shift the impedance selector switch to "4 Ω" position.
Step 3. Retighten the screw.
Remove the jumper strip.
11
7. RACK MOUNTING BRACKET ATTACHMENT
Each Power Amplifier can be mounted in a standard 19" equipment rack with the addition of the optional rack
mounting bracket MB-25B (P-906MK2 and P-912MK2) or MB-35B (P-924MK2).
Notes
• Rack mounting screws are not supplied with the unit. Use the screws that are appropriate for the rack.
• When mounting the unit in an equipment rack, the inside
of the rack must be sufficiently ventilated.
To achieve sufficient ventilation, also mount the optional
PF-511 Perforated Panel (1U*):
(1) at the top and the bottom of the rack, and
(2) above and below the unit.
* 1U size = 44.5 mm or 1.75" (reference size)
Amplifier
Amplifier
Amplifier
Perforated Panel
PF-511
(1-unit size)
S
IG
N
A
L
N
O
R
M
A
L
P
R
O
T
E
C
T
M
A
S
T
E
R
O
N
O
F
F
P
E
A
K
P
O
W
E
R
S
IG
N
A
L
N
O
R
M
A
L
P
R
O
T
E
C
T
M
A
S
T
E
R
O
N
O
F
F
P
E
A
K
P
O
W
E
R
Rack mounting screw
Machine screw M4 x 16
(supplied with the rack mounting bracket)
Rack mounting bracket *
* MB-25B for P-906MK2 and P-912MK2
MB-35B for P-924MK2
Step 1. Remove 4 plastic feet on the bottom surface when mounting the unit in a rack.
Step 2. Remove four M4 x 8 screws on both sides of the unit.
The removed screws are not used.
Step 3. Attach the brackets to the amplifier using four M4 x 16 Machine screws supplied with the bracket.
Master volume control knob
Volume control cover YA-920
(accessory)
9. VOLUME CONTROL COVER
To prevent the accidental change of the setting of the Master volume control, remove the knob after setting it
to the desired position and attach the optional cover YA-920 instead.
12
8. OPERATION
Be sure to complete all connections before operation.
Step 1. Press the power switch to turn on the power.
The power indicator lights green. The amplifier comes into operation about 5 seconds after the power
has been switched on.
Step 2. Adjust the master volume control for the optimum level.
Turn the knob clockwise to increase the output level and counterclockwise to decrease it.
[When the unit is used for normal music playing or announcement]
Adjust the master volume control so that the Normal Indicator intermittently lights. Sound quality is
downgraded when the Peak Indicator remains lit.
[When the unit is used in combination with a mixer preamplifier]
Adjust the total gain with the master volume control of the mixer preamplifier.
In this case, leave the master volume control of the power amplifier set at the fully clockwise position
(maximum gain level).
13
10. DIMENSIONAL DIAGRAMS
10.1. P-906MK2, P-912MK2
900
SERIES AMPLIFIER P
–
906
MK
2
SIGNAL NORMAL
PROTECT
MASTER
ON
OFF
PEAK
POWER
320 (12.6)17 (0.67)
358 (124.09)
Unit: mm (inches)
76.2 (3)
88.4 (3.48)
99.1 (3.9)
466 (18.35)
420 (16.54)
This figure represents the P-906MK2.
482.6 (19)
10.2. P-924MK2
900
SERIES AMPLIFIER P
–
924
MK
2
SIGNAL NORMAL
PROTECT
MASTER
ON
OFF
PEAK
POWER
Unit: mm (inches)
298.5 (11.75)17 (0.67)
334.2 (13.16)
482.6 (19)
466 (18.35)
420 (16.54)
57.2
(2.25)
132.6 (5.22)
151.3 (5.96)
14
15
11. SPECIFICATIONS
• Accessories
Volume control cover YA-920 .................... 1
Blank panel ................................................ 1
Machine screw M3 x 8 ............................... 2
• Optional product
Rack mounting bracket: MB-25B
11.1. P-906MK2, P-912MK2
Model No. P-906MK2 P-912MK2
Power Source 120 V AC, 60 Hz
Rated Output 60 W RMS 120 W RMS
Power Consumption
Rated output 100 W 180 W
Based on cUL standards 70 W 105 W
Power Bandwidth (D): 20 Hz – 20 kHz, 0.5% THD
(T): 50 Hz – 20 kHz, 0.5% THD
Frequency Response (D): 20 Hz – 20 kHz, ±1 dB
(T): 20 Hz – 15 kHz, ±1 dB
(T): 20 Hz – 20 kHz, +1 dB, –3 dB
Total Harmonic Distortion 0.01% at 1 kHz, rated output
Input One input port: port accepts any input module except T-01.
One direct input
Note: Use of direct input prohibits use of modular input port.
Input Sensitivity/Impedance Input port: 100 mV or 1000 mV (switchable) / 10 kΩ
Direct port: 100 mV or 1000 mV (switchable) / 10 kΩ
Output Main (T): 8 Ω, 25 V and 70 V, balanced
Main (D): 4 Ω, unbalanced
Output Regulation (1 kHz) (D): Less than 0.5 dB, no load to full load
(T): Less than 1.0 dB, no load to full load
Signal to Noise Ratio
(Band pass: 20 Hz – 20 kHz)
Input level switch in 0 dB (1000 mV) position: 108 dB
Input level switch in –20 dB (100 mV) position: 90 dB
Control 1 Input gain control, 1 Input level switch, 1 Power ON/OFF switch,
1 Low-cut switch
Indicator 1 Power LED, 1 Protect LED, 1 Signal LED, 1 Normal LED, 1 Peak LED
Protection Self-protection, with AC fuse (inside)
Connector Input: card-edge connector and screw-terminal strip
Output: screw terminal strip
AC outlet: 3-pin grounding type
AC power cord/plug: SJT, 3-prong type
Operating Temperature –10 to +60 °C (12 to 140 °F)
Other Feature Output disconnected for approx. 5 seconds after switching power on.
Color Black
Dimensions 420 (w) x 99.1 (h) x 358 (d) mm (16.54" x 3.9" x 14.09")
Weight 9.1 kg (20.06 lb) 12.1 kg (26.68 lb)
Notes
• The design and specications are subject to change without notice for improvement.
• (D): Direct output, (T): Transformer output
URL: https://www.toa.jp/
133-02-00086-01
11.2. P-924MK2
Power Source 120 V AC, 60 Hz
Rated Output (D): 240 W RMS, (T): 220 W RMS
Power Consumption
Rated output 120 V / 3 A
Based on cUL standards 180 W
Power Bandwidth (D): 20 Hz – 20 kHz, 0.5% THD
(T): 50 Hz – 20 kHz, 0.5% THD
Frequency Response (D): 20 Hz – 20 kHz, ±1 dB
(T): 20 Hz – 15 kHz, ±1 dB
(T): 20 Hz – 20 kHz, +1 dB, –3 dB
Total Harmonic Distortion 0.01% at 1 kHz, rated output
Input One input port: port accepts any input module except T-01.
One direct input
Note: Use of direct input prohibits use of modular input port.
Input Sensitivity/Impedance Input port: 100 mV or 1000 mV (switchable) / 10 kΩ
Direct port: 100 mV or 1000 mV (switchable) / 10 kΩ
Output Main (T): 8 Ω, 25 V and 70 V, balanced
Main (D): 4 Ω, unbalanced
Output Regulation (1 kHz) (D): Less than 0.5 dB, no load to full load
(T): Less than 1.0 dB, no load to full load
Signal to Noise Ratio
(Band pass: 20 Hz – 20 kHz)
Input level switch in 0 dB (1000 mV) position: 108 dB
Input level switch in –20 dB (100 mV) position: 90 dB
Control 1 Input gain control, 1 Input level switch, 1 Power ON/OFF switch,
1 Low-cut switch
Indicator 1 Power LED, 1 Protect LED, 1 Signal LED, 1 Normal LED, 1 Peak LED
Protection Self-protection, with AC fuse (inside)
Connector Input: card-edge connector and screw-terminal strip
Output: screw terminal strip
AC outlet: 3-pin grounding type
AC power cord/plug: SJT, 3-prong type
Operating Temperature –10 to +60 °C (12 to 140 °F)
Other Feature Output disconnected for approx. 5 seconds after switching power on.
Color Black
Dimensions 420 (w) x 151.3 (h) x 334.2 (d) mm (16.54" x 5.6" x 13.16")
Weight 18.3 kg (40.34 lb)
Notes
• The design and specications are subject to change without notice for improvement.
• (D): Direct output, (T): Transformer output
• Accessories
Volume control cover YA-920 .................... 1
Blank panel ................................................ 1
Machine screw M3 x 8 ............................... 2
• Optional product
Rack mounting bracket: MB-35B
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
TOA P-924MK2 UL Manuel utilisateur
- Catégorie
- Amplificateurs audio
- Taper
- Manuel utilisateur
dans d''autres langues
- English: TOA P-924MK2 UL User manual
Documents connexes
-
TOA A-906MK2 Manuel utilisateur
-
TOA A-912MK2 HH Manuel utilisateur
-
TOA D-2000DA1 Manuel utilisateur
-
-
Optimus A-5006 Manuel utilisateur
-
TOA DA-250D CU Manuel utilisateur
-
-
-
-
TOA BG-2480D Manuel utilisateur