Yamaha DME 32 Le manuel du propriétaire

DIGITAL MIXING ENGINE

Owner’s Manual

E

Keep This Manual For Future Reference.

SCENE NO. CONFIGURATION

48kHz

LOCK

EMERGENCY

44.1kHz

SCENE

COMPONENT PARAMETER

UTILITY

VALUE

CARD

USER DEFINE

PROTECT

INC

DEC

DIGITAL MIXING ENGINE

POWER

ON OFF

7 8 9

4 5 6

1 2

0

STORE RECALL

3

SCENE RECALLDATA

XDigitalXMixingXEngine

XXXXXYAMAHAXDME32

88

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all

installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on

different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in

is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be

connected to the terminal in the plug which is marked by the letter E

or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig

håndtering. Udskiftning må kun ske med batteri

af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd

samma batterityp eller en ekvivalent typ som

rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti

asennettu. Vaihda paristo ainoastaan

laitevalmistajan suosittelemaan tyyppiin. Hävitä

käytetty paristo valmistajan ohjeiden

mukaisesti.

NEDERLAND THE NETHERLANDS

● Dit apparaat bevat een lithium batterij voor geheugen

back-up.

● Raadpleeg uw leverancier over de verwijdering van de

batterij op het moment dat u het apparaat ann het einde

van de levensduur afdankt of de volgende Yamaha Service

Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

● Gooi de batterij niet weg, maar lever hem in als KCA.

● This apparatus contains a lithium battery for memory

back-up.

● For the removal of the battery at the moment of the

disposal at the end of the service life please consult your

retailer or Yamaha Service Center as follows:

Yamaha Music Nederland Service Center

Address: Kanaalweg 18-G, 3526 KL

UTRECHT

Tel: 030-2828425

● Do not throw away the battery. Instead, hand it in as small

chemical waste.

i

DME32—Owner’s Manual

Important Information

Read the Following Before Using the DME32

Warnings

• Do not subject the DME32 to extreme temperatures, humidity, direct sunlight, or dust,

which could be a potential ﬁre or electrical shock hazard.

• Do not allow water to enter the DME32 or allow it to become wet. Fire or electrical

shock may result.

• Do not place a container with liquid or small metal objects on top of this unit. Liquid

or metal objects inside this unit are a ﬁre and electrical shock hazard.

• Connect the power cord only to an AC outlet of the type stated in this Owner’s Manual

or as marked on the DME32. Failure to do so is a ﬁre and electrical shock hazard.

• Hold the power-cord plug when disconnecting from an AC outlet. Never pull the cord.

A power cord damaged through pulling is a potential ﬁre and electrical shock hazard.

• Do not touch the power plug with wet hands. Doing so is a potential electrical shock

hazard.

• Do not place heavy objects, including the DME32, on top of the power cord. A dam-

aged power cord is a ﬁre and electrical shock hazard. In particular, be careful not to

place heavy objects on a power cord covered by a carpet.

• Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a

ﬁre and electrical shock hazard.

• If the power cord is damaged (e.g., cut or a bare wire is exposed), ask your dealer for a

replacement. Using the DME32 with a damaged power cord is a ﬁre and electrical shock

hazard.

• Do not plug several pieces of equipment into the same AC outlet. This may overload

the AC outlet, and could be a ﬁre or electrical shock hazard. It may also affect the per-

formance of some equipment.

• If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or

liquid gets inside the DME32, turn it off immediately. Remove the power cord from the

AC outlet and consult your dealer for repair. Using the DME32 in this condition is a ﬁre

and electrical shock hazard.

• Do not place small objects on top of the DME32. Metal objects falling inside the

DME32 is a ﬁre and electrical shock hazard.

• If a foreign object or water gets inside the DME32, turn it off immediately. Remove the

power cord from the AC outlet and consult your dealer for repair. Using the DME32 in

this condition is a potential ﬁre and electrical shock hazard.

• Should the DME32 be dropped or the cabinet be damaged, turn off the power, remove

the power plug from the AC outlet, and contact your dealer. If you continue using the

DME32 without heeding this instruction, ﬁre or electrical shock may result.

• Do not remove the DME32’s cover. You could receive an electrical shock. If you think

internal inspection, maintenance, or repair is necessary, contact your dealer.

• Do not attempt to modify the DME32. This is a potential ﬁre and electrical shock hazard.

• Do not block the DME32 ventilation slots. Blocking the ventilation slots is a potential

ﬁre hazard.

ii

DME32—Owner’s Manual

Cautions

• Allow enough free space around the DME32 for normal ventilation. This should be

10 cm at the sides, 15 cm behind, and 30 cm above. These distances should also be

adopted when rack-mounting the DME32. For normal ventilation during use, remove

the rear of the rack or open a ventilation hole. If the airﬂow is not adequate, the DME32

will heat up inside and may cause a ﬁre.

• Use the DME32 in a environment with a free-air temperature of between 10˚C and

35˚C (50˚F and 95˚F).

• Turn off all audio equipment when connecting to the DME32, and use only the cables

speciﬁed in the relevant owner’s manuals.

• If you plan not to use the DME32 for a long period of time, remove the power cord from

the AC outlet. Leaving the DME32 connected is a potential ﬁre hazard.

• Do not use benzene, thinner, cleaning detergent, or a chemical cloth to clean the

DME32. Use only a soft, dry cloth.

• If the DME32 is stored in a cold place (e.g., overnight in a car), and then moved to a

warmer environment, or the temperature rises sharply, condensation may form inside

the DME32, which may affect performance. In such cases, the DME32 should be

allowed to acclimatize for about one hour before use.

• When the wordclock source is changed on the wordclock master device (e.g., AD824 or

DME32), noise may occur from the DME32’s analog outputs, especially if an MY8-AT

I/O card is installed, so turn down your power amps, or turn off the DME32 before-

hand, otherwise any connected speakers may be damaged.

• If the DME32 displays the message “Warning Low Battery” when it’s turned on, contact

your Yamaha dealer as soon as possible and ask them to replace the internal backup bat-

tery. Although the DME32 will continue to work in this condition, any conﬁguration

data will be lost. It’s recommended that you save any conﬁguration data using DME

Manager or a PC Card before replacing the battery.

Interference

The DME32 uses high-frequency digital circuits that may cause interference on radio

and television equipment located nearby. If interference is a problem, relocate the

affected equipment.

DME32 Exclusion of Certain Responsibility

Manufacturer, importer, or dealer shall not be liable for any incidental damages includ-

ing personal injury or any other damages caused by improper use or operation of the

DME32.

iii

DME32—Owner’s Manual

Package Contents

The DME32 package contains the following items. Contact your Yamaha dealer if you

are missing an item.

• DME32 Digital Mixing Engine

• CD-ROM (DME Manager software)

• 9-pin D-sub crossed cable (PC connection)

• 16-pin Euro-block plug (GPI interface)

• Power cord

• This manual

Trademarks

ADAT MultiChannel Optical Digital Interface is a trademark and ADAT and Alesis are

registered trademarks of Alesis Corporation. Intel and Pentium are registered trade-

marks and MMX is a trademark of Intel Corporation. Tascam Digital Interface is a

trademark and Tascam and Teac are registered trademarks of Teac Corporation. Win-

dows is a trademark of Microsoft Corporation. Yamaha is a trademark of Yamaha Cor-

poration. All other trademarks are the property of their respective holders and are

hereby acknowledged.

Copyright

No part of the DME32 or DME Manager software or this Owner’s Manual may be

reproduced or distributed in any form or by any means without the prior written

authorization of Yamaha Corporation.

Yamaha Web Site

Information about the DME32 and other Yamaha professional audio products is avail-

able on the Yamaha Professional Audio Web site at:

<http://www.yamaha.co.jp/product/proaudio/homeenglish/>.

Contents v

DME32—Owner’s Manual

Contents

1 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

The DME32 in a Nutshell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

DME32 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DME Manager Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

First Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Turning On & Off the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Upgrading & Reinstalling DME Manager . . . . . . . . . . . . . . . . . . . . . . . 12

Starting DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Quitting DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DME Manager & Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installing the USB Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Checking the Driver is Installed Correctly . . . . . . . . . . . . . . . . . . . . . . . 14

USB Operating Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3 Touring the DME32 . . . . . . . . . . . . . . . . . . . . . . . . 15

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4 Touring DME Manager . . . . . . . . . . . . . . . . . . . . . 21

Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Main Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Configuration Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Component Control Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Run Mode Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Other Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Touring the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Component List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Tool Palette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Alt Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Keyboard Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5 Building Configurations . . . . . . . . . . . . . . . . . . . . 43

How to Build & Edit Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Selecting Edit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Opening New Configuration Windows . . . . . . . . . . . . . . . . . . . . . . . . . 45

Opening Saved Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Selecting Open Configuration Windows . . . . . . . . . . . . . . . . . . . . . . . . 46

Adding Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

vi Contents

DME32—Owner’s Manual

Editing Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Aligning Components to the Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Zooming Configuration Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Selecting Cable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Adding Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Deleting Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Working with Multiple-Unit Configurations . . . . . . . . . . . . . . . . . . . . 58

Resizing Sections of the Configuration Window . . . . . . . . . . . . . . . . . 59

Saving Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Saving Configurations under a New Name . . . . . . . . . . . . . . . . . . . . . . 60

Closing Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Compiling Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Sending Configurations to the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . 62

Receiving Configurations from the DME32 . . . . . . . . . . . . . . . . . . . . . 63

6 Running the System . . . . . . . . . . . . . . . . . . . . . . . . 65

Selecting Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Run Mode Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Editing Component Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Storing Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Recalling Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Recalling Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

7 Other DME Designer Functions . . . . . . . . . . . . . . . 75

Editing Scenes Offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Linking Component Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Customizing Component Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Changing the Size of Rotary Controls & Sliders . . . . . . . . . . . . . . . . . . 82

Using Password Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Assigning the User Define Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

8 Component Guide Part I . . . . . . . . . . . . . . . . . . . . 89

Automatic Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Crossover Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Delayed Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Dynamics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

9 Component Guide Part II . . . . . . . . . . . . . . . . . . . 141

Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

Fader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165

Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

Input/Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

Matrix Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174

Misc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

Contents vii

DME32—Owner’s Manual

Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

User Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

User Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

10 Front Panel Operation . . . . . . . . . . . . . . . . . . . . . . 197

Recalling Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

Storing Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

Recalling Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

Editing Parameters & the User Define Button . . . . . . . . . . . . . . . . . . . 201

Restricting Access to the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

Selecting the Wordclock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209

Checking the I/O Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210

Initializing the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210

Checking the Firmware Version & Battery . . . . . . . . . . . . . . . . . . . . . . 210

11 GPI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211

About the GPI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212

GPI Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212

Assigning GPI Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

Assigning GPI Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

Emergency Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220

12 PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221

PC Cards & the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222

Inserting & Ejecting PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222

Formatting PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223

Saving Configurations to PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224

Loading Configurations from PC Cards . . . . . . . . . . . . . . . . . . . . . . . . 225

Deleting Configurations from PC Cards . . . . . . . . . . . . . . . . . . . . . . . . 226

13 Wordclocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227

Wordclocks & the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228

Wordclock Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

Selecting the Wordclock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

Wordclock Hookup Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231

Terminating BNC Wordclock Distribution . . . . . . . . . . . . . . . . . . . . . 234

14 Multiple DME32s . . . . . . . . . . . . . . . . . . . . . . . . . . 235

About Multiple DME32s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236

Multiple-Unit System Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236

Cascade Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237

Multiple-unit Hookup Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238

15 MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241

MIDI & the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

MIDI Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

MIDI Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

Assigning Scenes & Configurations to Program Changes . . . . . . . . . . 244

Assigning Component Parameters to Control Changes . . . . . . . . . . . 246

viii Contents

DME32—Owner’s Manual

Component Parameters & Parameter Changes . . . . . . . . . . . . . . . . . . 248

Saving MIDI Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249

Loading MIDI Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

Deleting MIDI Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

16 I/O Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

I/O Options & the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252

I/O Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

Choosing I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

Installing I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255

AD824 & DA824 Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261

DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261

DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263

Appendix A: General . . . . . . . . . . . . . . . . . . . . . . . . . 265

Component Title Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

DME32 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270

DME Manager Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271

Appendix B: Specifications . . . . . . . . . . . . . . . . . . . . . 273

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

Control I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

DME32 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277

Appendix C: MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279

Program Change Assign Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279

Control Change Assign Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289

MIDI Implementation Chart

Welcome 1

DME32—Owner’s Manual

Welcome

1

In this chapter...

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

The DME32 in a Nutshell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

DME32 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DME Manager Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Chapter 1—Welcome

DME32—Owner’s Manual

Welcome

Thank you for choosing the Yamaha DME32 Digital Mixing Engine.

The DME32 Digital Mixing Engine and DME Manager software allow sound-system

installers to custom build systems to meet the speciﬁc requirements of almost any

installation. Entire systems from input through to output can be designed using DME

Manager and then transferred to the DME32, which can then be used as a standalone

processor. Typical applications include installed sound systems, submixing, loud-

speaker system controllers, matrix/routing, and multi-effects processing.

The DME32 in a Nutshell

DME32 audio systems, or conﬁgurations as they’re known in DME32 terminology, are

built in an intuitive “block diagram” style using Yamaha’s dedicated DME Manager

software. Building conﬁgurations consists of adding the necessary components, wiring

them together, compiling, and then transferring that information to the DME32, using

either RS232/RS422, USB (Universal Serial Bus), or PC Cards.

Once programmed, the DME32 operates as a standalone processor and the PC can be

disconnected, although it can be connected permanently in applications where

real-time control from DME Manager is desirable. Even then, if the PC connection is

lost for some reason, the DME32 just keeps on going.

Components form the building blocks in conﬁgurations. Some components are com-

plete audio processors, such as mixers, compressors, effects, and crossovers, while oth-

ers are individual parts, such as faders, switches, pan controls, and meters. System

designers can create their own custom components using the User modules.

DME Manager operates in one of three modes: Edit, Cable, or Run. Edit mode is used

mainly to build and edit conﬁgurations, although it can also be used to edit and preview

scenes ofﬂine. Cable mode is for wiring components together. Run mode is used to con-

trol the DME32 system in real time, which includes editing component parameters,

storing and recalling scenes, and recalling conﬁgurations. In Run mode, actions per-

formed on DME Manager are reﬂected on the DME32 and vice versa.

The DME32 can store two conﬁgurations: A and B. Additional conﬁgurations can be

stored on PC Cards. Each conﬁguration can store up to 99 scenes, or snapshots of every

component parameter setting in the conﬁguration. Conﬁgurations and scenes can be

recalled from the DME32 front panel, DME Manager, MIDI, or the GPI interface. Con-

ﬁgurations and scenes can be titled from the PC keyboard for easy identiﬁcation.

When operating as a standalone processor, various DME32 functions can controlled

from the front panel, including editing component parameters, storing and recalling

DME

Manager

32 outputs32 inputs

Control

SCENE NO. CONFIGURATION

48kHz

LOCK

EMERGENCY

44.1kHz

SCENE

COMPONENT PARAMETER

UTILITY

VALUE

CARD

USER DEFINE

PROTECT

INC

DEC

DIGITAL MIXING ENGINE

POWER

ON OFF

7 8 9

4 5 6

1 2

0

STORE RECALL

3

SCENE RECALLDATA

XDigitalXMixingX Engine

XXXXXYAMAHAXDME32

88

The DME32 in a Nutshell 3

DME32—Owner’s Manual

scenes, and recalling conﬁgurations. Direct access to a speciﬁc parameter is possible by

assigning it to the [USER DEFINE] button. The large, two-digit scene number display

indicates the current scene, while the 48-character LCD displays conﬁguration and

scene titles, component and parameter names, parameter values, and so on. Unautho-

rized operation can be prevented by using the password protection.

The DME32 offers 32 inputs and 32 outputs via four mini YGDAI card slots. Optional

mini YGDAI (Yamaha General Digital Audio Interface) cards offer a variety of analog

and digital I/O conﬁgurations, with support for all the popular digital audio intercon-

nect formats, including AES/EBU, ADAT, and Tascam TDIF-1. Inputs and outputs can

be expanded in multiples of 32 by cascading additional DME32s. Up to four DME32s

can be cascaded, providing a maximum of 128 inputs and 128 outputs. Cascade com-

ponents offer bus-like signal distribution in multiple-unit systems and can also be used

for DSP power sharing between DME32s.

Superb sonic performance is achieved using 32-bit internal signal processing and a

48 kHz internal sampling rate. External sampling rates of between 39.69 kHz to

50.88 kHz are supported and can be set individually for each conﬁguration.

Remote interaction between DME32 functions and custom-made controllers and

other equipment is possible using MIDI and the GPI interface, which offers 16 assign-

able inputs and 16 assignable outputs. Scenes and conﬁgurations can be recalled using

MIDI Program Change messages or the GPI interface. Component parameters can be

controlled by using MIDI Control Change messages, System Exclusive messages, or

custom-made controllers attached to the GPI interface.

See page 4 for a rundown of DME32 features, page 6 for DME Manager features.

4 Chapter 1—Welcome

DME32—Owner’s Manual

DME32 Features

Sonic Performance

• 32-bit internal signal processing

• 48 kHz internal sampling rate

• 39.69 kHz to 50.88 kHz external wordclock

Memories & Storage

• 2 conﬁguration memories: A and B

• 99 scene memories per conﬁguration

• Conﬁgurations and scenes can be titled from the PC keyboard for easy identiﬁcation

• Store and transfer conﬁgurations on PC Cards

Flexible I/O

• 32 inputs, 32 outputs via four mini YGDAI slots

• Optional mini YGDAI cards offer a variety of analog and digital I/O conﬁgurations,

with support for all the popular digital audio interconnect formats, including

AES/EBU, ADAT, and Tascam TDIF-1.

• Analog I/O options include the Yamaha AD824 8-channel 24-bit A/D converter and

DA824 8-channel 24-bit D/A converter

Control Ports

• Switchable RS232/RS422 serial port for PC connection

• RS422 allows cable lengths of up to one kilometer (15 meters for RS232)

• Convenient front panel USB port for PC connection

• COM port for AD824 head-amp gain control

Multiple Units

• Cascade ports for multiple-unit operation with up to four DME32s

• I/O expansion in multiples of 32, with a maximum of four DME32s providing 128

inputs and 128 outputs

• 32 cascade buses allow bus-like signal distribution and power sharing between DME32s

Remote Control

• Conﬁguration and scene recall using MIDI Program Changes

• Component parameter control using MIDI Control Changes or System Exclusive

• GPI interface with 16 assignable inputs, 16 assignable outputs

• Emergency mode assignable to any GPI input

DME32 Features 5

DME32—Owner’s Manual

Standalone Operation

• DME Manager can be disconnected once the DME32 has been programmed

• Dedicated keypad for scene store and recall

• Data wheel and INC/DEC buttons for component parameter editing

• Assignable [USER DEFINE] button for quick parameter access

Others

• Large, 2-digit scene number indicator

• 48-character LCD display

• Password protection prevents unauthorized operation

• Wordclock I/O and switchable termination for master/slave operation

• 3U rack space

6 Chapter 1—Welcome

DME32—Owner’s Manual

DME Manager Features

Components

• Processor components include crossovers, dynamics, ﬁlters, GEQ, PEQ, effects, etc

• Part-type components include faders, meters, switches, pan controls, etc

• Create custom components using User Modules

• Copy frequently used controls to custom control windows

• Customize the size of rotary controls and sliders

Edit mode

• Drag and drop components onto conﬁguration windows

• Use standard cut, copy, and paste commands to edit components

• Customize component appearance, including title, size, and color

• DSP power meter indicates approximate processor usage

• Align and snap components to the variable grid

• Zoom in to see components in detail or zoom out to see more of a conﬁguration

Cable Mode

• Wire components by dragging wires between input and output nodes

• Wire component nodes individually or in multiples

Run mode

• Real-time control using DME Manager

• Edit component parameters, recall and store scenes, and recall conﬁgurations

• Actions performed on DME Manager are reﬂected on the DME32 and vice versa

Ofﬂine Operation

• Build and edit conﬁgurations off-site

• Edit, title, and delete scenes ofﬂine

• Preview scenes ofﬂine

Conﬁgurations & Scenes

• Title conﬁgurations and scenes from the PC keyboard

• Save conﬁgurations to any media available to Windows, including PC Cards

• Open multiple conﬁgurations simultaneously

Easy Operation

• Drag rotary controls and sliders

• Set PEQ parameters by dragging points on an EQ curve

• Context-sensitive shortcut menu containing frequently used commands

• Floating tool palette and Alt-click mode menu for quick mode switching

About this Manual 7

DME32—Owner’s Manual

Other Features

• Up to 32 parameter-link groups for fader grouping, stereo signal control, or crossover

frequency control in multiple-speaker systems

• Link parameters across cascaded DME32s

• 3-level password protection allows full access, limited access, or no access

• Print conﬁguration information, including diagrams, component and parameter lists

About this Manual

This Owner’s Manual contains all the information you need in order to operate the

DME32 Digital Mixing Engine and DME Manager. Use the table of contents to famil-

iarize yourself with the organization of this manual and locate topics. Use the index to

locate speciﬁc information. A glossary of DME32-related jargon is provided on

page 287.

In this manual, the DME32 Digital Mixing Engine and DME Manager software are

referred to as the “DME32” and “DME Manager” respectively. “PC” refers to an IBM

PC-compatible computer running a Windows operating system.

Installing the DME32

When mounting the DME32 in a rack, remove the DME32’s feet and leave adequate

ventilation space around the DME32 (at least 15 cm of free space behind). If the

DME32 is mounted in a portable rack case, keep the rear of the case open when using

the DME32 so as not to obstruct the free ﬂow of air. Do not mount the DME32 above

equipment that produces a lot of heat, such as a power ampliﬁer.

Getting Started 9

DME32—Owner’s Manual

Getting Started

2

In this chapter...

First Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Turning On & Off the DME32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Upgrading & Reinstalling DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Starting DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Quitting DME Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DME Manager & Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installing the USB Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Checking the Driver is Installed Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

USB Operating Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

10 Chapter 2—Getting Started

DME32—Owner’s Manual

First Steps

Here’s how to get up and running with the DME32 system with the minimum of fuss.

1 Familiarize yourself with the DME32.

See “Touring the DME32” on page 15.

2 Install the required mini YGDAI I/O cards.

See “I/O Options” on page 251.

3 Connect your audio sources and other equipment to the inputs and outputs.

4 Connect the DME32 to your PC.

See “Connecting to a PC” on page 10.

5 Connect the power cord and turn on the DME32.

See “Connecting the Power Cord” on page 11 and “Turning On & Off the DME32” on

page 11.

6 Install DME Manager.

See “Installing DME Manager” on page 12.

7 Start DME Manager.

See “Starting DME Manager” on page 12.

8 Familiarize yourself with DME Manager.

See “Touring DME Manager” on page 21.

9 Build a conﬁguration.

See “Building Conﬁgurations” on page 43.

10 Compile the conﬁguration.

See “Compiling Conﬁgurations” on page 61.

11 Transfer the conﬁguration to the DME32.

See “Sending Conﬁgurations to the DME32” on page 62.

12 Take the conﬁguration for a run.

See “Running the System” on page 65.

Connecting to a PC

The DME32 can be connected to a PC by using standard RS232/RS422 serial connections or

USB (Universal Serial Bus). When the DME32 receives a command via the serial port, it

transmits a response to only the serial port. Likewise, when it receives a command via the

USB port, it transmits a response to only the USB port.

Serial Port

The PC CONTROL port features a switch for selecting

RS232 or RS422. These two serial port standards are virtu-

ally the same, the main difference being that RS422 is bal-

anced and therefore supports longer cable lengths. RS232

supports cable lengths of up to 15 meters, while RS422 sup-

ports lengths of up to 1 kilometer. Select the one that

matches your PC’s serial port.

PC CONTROL

RS

232C

RS

422

Serial cable

COM port

PC CONTROL port

12345678

910111213141516

SLOT

2

SLOT

4

SLOT

1

SLOT

3

CASCADE INCASCADE OUTCOMPC CONTROLMIDI

AC IN

WORD CLOCK

IN

OFFON

75Ω

OUT OUT IN

IN +V

OUT GND

GND

IN +V

OUT

RS

232C

RS

422

Connecting the Power Cord 11

DME32—Owner’s Manual

You can specify which COM port on your PC DME Manager uses, although you’ll need to

install DME Manager in order to do this. See “Installing DME Manager” on page 12 for more

information. Using a text editor, open the “setup.ini” ﬁle in the DME folder. Change the COM

parameter to match the number of the COM port you want to use. To use COM port 2, for

example, the setting should be “COM2” (without quotation marks).

USB

The front panel USB port is a convenient way to connect a PC to the DME32 and

is ideal for systems where the DME32 rear panel is not easily accessible.

Connecting the Power Cord

Connect the socket-end of the supplied power cord to the AC IN socket on

the rear panel of the DME32. Connect the plug-end to a suitable AC wall out-

let, one that conforms to the power supply requirements stated on the

DME32 rear panel.

Turning On & Off the DME32

To prevent loud clicks and thumps in your speakers, turn on your audio

equipment in the following order (reverse this order when turning off

your equipment)—sound sources, mixer or recorder (e.g., 02R, DME32,

D24, etc.), power ampliﬁers.

1 To turn on the DME32, press the [POWER] switch.

The following message appears for a few moments.

The number and title of the current conﬁguration and scene appear on the display. The ﬁrst

parameter of the ﬁrst component is selected, unless the [USER DEFINE] button has been

assigned, in which case, the parameter assigned to that button is selected and the USER

DEFINE indicator lights up.

When the DME32 is turned on for the ﬁrst time, or when it’s initialized, conﬁguration mem-

ory A contains a simple conﬁguration titled “Mtrx16.” This conﬁguration is stored inside the

DME32 and can be overwritten by transferring another conﬁguration from DME Manager.

2 To turn off the DME32, press the [POWER] switch.

Important: You need to install the USB driver in order to use the USB port. See page 13.

Warning: Turn off all equipment before making any power connections.

SCENE NO. CONFIGURATION

48kHz

LOCK

EMERGENCY

44.1kHz

SCENE

COMPONENT PARAMETER

UTILITY

VALUE

CARD

USER DEFINE

PROTECT

INC

DEC

DIGITAL MIXING ENGINE

POWER

ON OFF

7 8 9

4 5 6

1 2

0STORE RECALL

3

SCENE RECALLDATA

XDigitalX MixingXEngine

XXXXXYAMAHAXDME32

88

USB cable

USB port

AC IN

POWER

ON OFF

XDigitalXMixingXEngine

XXXXXYAMAHAXDME32

12 Chapter 2—Getting Started

DME32—Owner’s Manual

Installing DME Manager

System Requirements

• A computer with a 200 MHz or faster Intel Pentium MMX processor or equivalent

• At least 32 MB of RAM (64 MB or more recommended)

• A hard disk with at least 20 MB of free space

• A CD-ROM or DVD-ROM drive (installation only)

• A VGA or better display (640 x 480, 256 color minimum)

• An RS232 or RS422 serial port or a USB port

• Windows 95/98

Installing DME Manager

Before installing DME Manager, make sure that your PC meets the system requirements

listed previously.

1 Turn on your PC and, if it’s not running already, start Windows.

The PC does not need to be connected to the DME32 in order to install DME Manager.

2 Insert the DME32 CD-ROM disc into your CD-ROM or DVD-ROM drive.

If the Windows CD-ROM Autorun feature is turned on, the installation start up screen

appears automatically.

3 Continue with the installation as prompted.

If the Windows CD-ROM Autorun feature is not turned on, you must start the installation

manually, as explained below.

4 Double-click the My Computer icon.

The My Computer window opens.

5 Double-click the “DME32” CD-ROM icon.

The installation start up screen appears.

6 Continue with the installation as prompted.

When the installation process is complete, remove the CD-ROM disc from the CD-ROM

drive and return it to its case for safe keeping.

The installation program adds a DME item to the Windows Programs menu.

Upgrading & Reinstalling DME Manager

Before upgrading or reinstalling DME Manager, you must delete the previously installed ver-

sion as follows.

1 Use the “Add/Remove Programs” control panel to remove DME Manager.

2 Locate the “DME” folder and delete all the ﬁles inside it (do not delete the

“AddIn,” “Midi,” or “Module” folders or the ﬁles inside them).

Normally the “DME” folder is in “C:\Program Files.”

Starting DME Manager

1 Click the Windows “Start” button and select Programs, DME.

DME Manager starts.

When DME Manager is started, it checks whether any active DME32s are connected, active

meaning connected and turned on. If an active DME32 containing conﬁguration data is

detected, a message asking whether or not you want to receive the conﬁguration data

appears. If you choose to receive it, all the conﬁguration data in the DME32 is transferred to

DME Manager and displayed in new conﬁguration windows, and DME Manager switches to

La page charge ...

Yamaha DME 32 Le manuel du propriétaire

Ce manuel convient également à

Yamaha DME 32 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents