brondell CSG15 Le manuel du propriétaire

Owner's Manual

SWASH CSG15

ADVANCED BIDET SEAT

Owner’s Manual

ADVANCED BIDET SEAT

SWASH LT89 / LE89

2

This manual contains important safety information.

Before operating the bidet, please read this manual

thoroughly, and retain it for future reference.

PRODUCT INSTALLATION

GENERAL INFO

PRODUCT OPERATION

01 SAFETY INFORMATION

06

07

08

PRODUCT INFORMATION

Product Features

Product Dimensions

Product Parts

09

10

11

13

PRODUCT INSTALLATION

Installation Parts

Before Installation

Swash Installation

External Bidet Filter Installation

14

16

17

OPERATING THE SWASH

CSG15 Control Panel

Using the CSG15

Special Mode Operations

TECHNICAL INFO

TRANSLATIONS

19 PRODUCT SPECIFICATIONS

20

21

MAINTENANCE

Seat Cleaning & Removal

Nozzle Cleaning

Cleaning the Mesh Filter

Product Storage

22 TROUBLESHOOTING

25 WARRANTY

26 CONTACT

1ENGLISH

27 SPANISH

54 FRENCH

CSG15 OWNER'S MANUAL

Table of Contents

1

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION TO PREVENT

PROPERTY LOSS AND ENSURE SAFETY.

DANGER: If not observed, serious injury or even death may occur as a result.

WARNING: If not observed, serious physical injury or property damage may occur as a result.

CAUTION: If not observed, minor physical injury or property damage may occur as a result.

DANGER Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

• Do not use a damaged power plug or plug into a loose electric outlet.

• Do not move the product by pulling the power cord.

• Do not handle the product or power plug with wet hands.

• Do not forcefully bend the power cord or place heavy objects on it to prevent it from being

damaged or deformed.

• Do not connect and pull out the power plug or cord repeatedly.

• Unplug the product before cleaning, repairing, inspecting, or replacing parts.

• Remove any dust or water from the power plug prior to plugging in.

• Do not plug the product into an electrical outlet or power strip that is being used by too many

other products. Use an electrical outlet adequate for the wattage of the product rated for a

minimum of 15 amps.

• If the power cord is damaged, do not attempt to repair, modify, or replace the cord yourself.

Contact the Brondell Service Center toll free at 888-542-3355 or email us through our website.

• If the product produces a strange noise, a burning smell, or emits smoke, unplug it immediately

from the electrical outlet and contact Brondell. Failure to do so may result in electric shock or ﬁre.

• Do not insert any wires or sharp objects into any product gaps. This may result in electric shock,

ﬁre, or product damage.

• Do not place an electronic or gas heater near the product or dispose of any burning materials

such as a lit cigarette in the toilet. This may result in ﬁre or product deformation. Do not place any

containers ﬁlled with water or other liquids, food, metallic objects, or any ﬂammable material on

top of the product. If foreign material enters the product, this may result in electric shock or ﬁre.

SAVE THESE INSTRUCTIONS

2

• Do not plug in, operate, or store the unit in locations where ﬂammable or combustible materials are

used or kept.

• Do not use industrial water, or gray water for the supply, as this may cause skin damage or disease.

• Turn o the main water supply valve when cleaning.

• For children and seniors who may have diculties with adjusting temperatures or those with

sensitive skin or impaired heat sensitivity, set the temperature of the wash spray and seat to “low”

or “o” to prevent burning.

• Close supervision is necessary when this product is used by children, seniors, or persons requiring

general assistance.

• Do not press the buttons using excessive force.

• Do not stand on top of or place any heavy objects onto the seat cover.

• Use this product for its intended use only, as described in this manual. Do not use any attachments

that are not recommended by Brondell.

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

DANGER Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

• Do not use the product in locations exposed to excessive moisture and do not splash water

onto the product.

• While cleaning the bathroom, pull the power plug out of the electrical outlet and exercise

caution to ensure that water or cleaning supplies do not splash onto the bidet. Failure to do so

may result in electric shock or ﬁre.

• If foreign material enters the product, pull the power plug out of the electrical outlet, turn o

the main water valve, and call the Brondell Service Center.

• Do not disassemble, repair, or modify the product yourself.

• Do not use the product while wet from bathing or showering.

• Do not place or store the product where it can fall or be pulled into a tub or sink.

• Do not place in or drop the product into water or any other liquid.

• Do not reach for the product if it has fallen into water. Unplug the product immediately and call

the Brondell Service Center.

• Do not use the product if it is not working properly. Please unplug the product immediately,

close the main water supply valve, and call the Brondell Service Center at 888-542-3355.

Failure to do so may result in electric shock, ﬁre, or ﬂooding.

WARNING Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

3

SAVE THESE INSTRUCTIONS

• Do not connect the main water supply to the hot water pipe or supply (only connect to the

cold water supply).

• After the installation, make sure to check all water supply connections for leaks. Rubber

washers should be in place for the water connection hoses & T-valve.

• Do not open/close the seat or seat cover with excessive force.

• Exercise caution that urine does not come into contact with the product - failure to do so may

result in bad odors or malfunction.

• If the product will not be used for a long period of time, unplug the power cord, close the

main water supply valve, and drain any water in the water tank.

• Do not pull out the bidet hose using excessive force.

• Do not use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent on or

near the product. This may result in corrosion to the metal parts or discoloration or scratches

to the bidet body.

• This appliance is not intended for use by persons (including children and seniors) with

reduced physical, sensory, or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning the use of the appliance by

a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water. Contact the Brondell Service Center for

examination and repair.

• Keep the cord away from heated surfaces and heating vents.

• Never block the air openings of the product or place it on a soft surface, such as a bed or couch,

where the air openings may be blocked. Keep the air openings free of lint, hair, etc.

• Never drop or insert any object into any opening or hose.

• Do not use the product outdoors or operate where aerosol (spray) products are being used or a

room where it could be exposed to oxygen.

• Connect this product to a properly grounded outlet only. Refer to the Grounding Instructions in

the next pages of the manual.

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

WARNING Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

CAUTION Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

4

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

Ground GFCI Outlet

ATTENTION

This product should only be used with a grounded GFCI (Ground Fault

Circuit Interrupter) outlet and a grounded three-prong electrical cord

as shown to the right. In the event of an electrical short circuit, using a

grounded GFCI outlet reduces the risk of electric shock.

This product is equipped with a grounded cord and is for use on a

nominal 120V circuit only (minimum 15 amps) and must be plugged

into an outlet that is properly grounded with a GFCI breaker as shown.

Replace or repair a damaged cord immediately.

Test

Reset

Grounding Pin

IMPROPER USE OF THE GROUNDING PLUG CAN RESULT

IN A RISK OF ELECTRIC SHOCK.

• If repair or replacement of the cord or plug is necessary,

do not connect the grounding wire to either ﬂat blade

terminal. The wire with green insulation (either with or

without a yellow stripe) is the grounding wire.

• Check with a qualiﬁed electrician if the grounding

instructions are not completely understood, or if there is

doubt if the product is properly grounded.

For those with certain medical or mobility issues in the bathroom,

we recommend our Swash 1400 or Swash 1000 bidet seats, as their

mounting systems are engineered for the most secure transitions from

wheelchairs or walkers.

GROUNDING AND GFCI OUTLET INSTRUCTIONS

SAVE THESE INSTRUCTIONS

DANGER Improper use of the grounding plug can result in a risk of electric shock.

5

DANGER Do not connect the grounding wire to a

non-grounded outlet.

SAVE THESE INSTRUCTIONS

OPTIONAL GROUNDING INSTRUCTIONS

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

This product is for use on a nominal 120V circuit, and has a grounding

plug that looks like the plug illustrated in sketch A in Figure 1.

A temporary adapter, which looks like the adapter illustrated in

sketches B and C, may be used to connect this plug to a 2-pole

receptacle as shown in sketch B if a properly grounded outlet is

not available.

The temporary adapter should be used only until a properly grounded

outlet (sketch A) can be installed by a qualiﬁed electrician.

A

B

D

C

Figure 1

Figure 2

Attach the grounding wire to the grounding screw on the product as

shown in sketch D of Figure 2. Attach the other end of the grounding

wire to the grounding screw located on the temporary outlet.

6

Stainless Steel Nozzle

Stainless steel resists soiling and bacterial

contamination for enhanced hygiene.

Posterior and Feminine Warm Water Wash

Experience the ultimate in clean with

adjustable temperature, position, pressure,

massage, and oscillation settings.

Strong Wash

Concentrated stream with adjustable

pressure, position, temperature, massage, and

oscillation settings.

Positionable Nozzle

The nozzle has ﬁve dierent positions

to ensure the most comfortable and

complete wash.

Adjustable Water Temperature and Pressure

Front, Rear and Strong wash modes have four

available water temperature settings, and ﬁve

water pressure settings.

Pulse

When activated, the water pressure

automatically increases and decreases to

provide a pulsating, cleaning spray.

Warm Air Dryer

Includes adjustable temperature with ﬁve

levels for a hands-free experience and

toilet paper reduction – even elimination.

PRODUCT INFORMATION

Product Features

Nozzle Oscillation

The Move function provides a massaging,

oscillating cleanse during the wash cycle

ensuring a thorough and comfortable wash.

Gentle Wash Function

Activates a preset wash cycle at the softest

setting for a gentle clean. A drying cycle will

follow.

Ergonomic Heated Seat

With four temperature settings

(High/Medium/Low/O).

Illuminating Nightlight

The cool blue hue of the nightlight means

no more blinding lights during midnight trips

to the bathroom.

Gentle-Closing Seat and Lid

“Slam free” gentle-closing seat and lid are

user friendly.

Eco Mode

When activated, this function automatically

lowers the water and seat temperature to one

of two dierent settings.

Quick-Release Seat

Quick-release button for easy removal and

cleaning of seat and toilet.

7

4.72 in – 8.27 in

Required Distance Between Mounting Holes

18.5 in

15.9 in

8.1 in

11.4 in

8.1 in

2.1 in

20.7 in

19.5 in

10.6 in

2.1 in

Elongated Top View

Round Top View

PRODUCT INFORMATION

Product Dimensions

8

1. Lid

2. Seat Sensor

3. Warm Seat

4. Warm Air Dryer

5. Nozzle Assembly

6. LED Nightlight

7. Control Panel

8. Power Plug

9. Water Inlet with Mesh Filter

10. Drain Plug

11. Mounting Plate

12. Quick-Release

13. Grounding Wire

PRODUCT INFORMATION

Product Parts

9

1. Mounting Bolt (2)

2. Rubber Cone Washer (2)

3. Flat Washer (2)

4. Nuts (2)

5. Mounting Plate

6. Adjustable Brackets (2)

7. T-Valve Connector with

Rubber Washer

8. Bidet Hose

PRODUCT INSTALLATION

Installation Parts

10

PRODUCT INSTALLATION

Before Installation

DO NOT PLUG THE PRODUCT IN WHILE THE UNIT IS UPSIDE DOWN

This may cause damage to the internal components.

WATCH OUR INSTALLATION VIDEO

Installation for all Swash products can be found online at brondell.com

CHECK BOLT SPREAD

This bidet seat can only be installed on toilets with a bolt hole spread of 4.72 – 8.27 in.

(see Product Dimensions on page 7 for more information).

CHECK FOR TOP MOUNT INSTALLATION

If your ﬁxture only has top-side access to the mounting bolts that hold the seat to the toilet, you

will likely need to purchase the Swash Bidet Seat Top Mount Hardware Kit, found on brondell.com.

CHECK FOR A CONCEALED TOILET FILL VALVE

Many modern toilets have sleek designs intended to cover and camouﬂage plumbing

connections, which make a standard Swash installation dicult or impossible. For this, we

recommend using our Alternate Swash Bidet Seat T-valve, found on brondell.com.

CHECK WATER SUPPLY LINE

Check the line that connects the toilet tank to the water shut o valve. If it is a rigid pipe, you may

need to purchase a ﬂexible hose to replace it before installing the Swash. The length of the hose

and the size of the connectors will vary.

RESIDUAL MOISTURE IS NORMAL

Every product is tested with pure water during production to ensure the highest quality and

performance. It is normal to ﬁnd a small amount of residual moisture on the product and in the

reservoir and ﬁlter.

TOOLS

A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a

standard wrench may be needed for tight water supply connections. Teﬂon tape can be helpful in

creating a water-tight seal between plumbing connections.

11

3. Connect the top of the T-valve to the incoming water connection on

the bottom of your toilet tank.

4. Connect the water supply line coming from the wall to the bottom of

the T-valve.

5. Install Mounting Plate for Standard Installation

a. Place mounting plate over mounting holes on toilet, rubber side

facing down, arrow pointing to the toilet tank.

b. Place adjustable brackets ﬂat side down in the center of the square

opening in the mounting plate and insert mounting bolts through

adjustable brackets and mounting holes. Be sure that the square

mounting bolt head is even with sides of adjustable bracket.

1. Existing Toilet Seat Removal

a. Lift hinge covers and use a screwdriver to remove the

mounting bolts.

b. Remove the toilet seat. Keep for future use.

2. Turn O Water Supply Valve and Flush Toilet

a. Turn water valve o to stop the ﬂow of water.

b. Flush toilet and hold down handle to completely

empty tank.

c. Disconnect water supply hose from toilet tank. Do not

disconnect from the water supply valve.

PRODUCT INSTALLATION

Swash Installation

Please read these instructions carefully before installing the Swash.

Failure to do so could result in ﬂooding, leaking or damage to the product.

NOTE: Steps may vary by type of seat and toilet

NOTES

• You may wish to place a container under the tank to catch excess water.

• Do not continue without completing the above steps.

• Failure to do so could result in ﬂooding, leaking or damage to the Swash.

NOTES

• The T-valve connects to the ﬁll valve directly under your toilet tank - it

does not connect at the wall.

• Only connect to the cold toilet water supply line.

• If your water supply line is rigid you may need to replace the water

supply line before continuing. Steps 3-4

Toilet tank

T-valve

Cold

water

supply

line

Step 2c

Steps 5b-5c

12

6. Connect the Bidet Hose to the Seat

Connect the plastic side of the bidet hose to the water inlet.

Hand-tighten to secure. Take care not to twist the bidet hose,

excessively bend it, or strip the plastic screw threads when

screwing the hose onto the bidet seat.

7. Attach the Swash to the Mounting Plate

a. Set the Swash ﬂat on the toilet bowl in front of the mounting

plate, and slide seat onto plate until it is secure.

b. If the seat appears too short or too long for the toilet, adjust

the mounting plate accordingly. To adjust the mounting plate,

loosen the nuts underneath the toilet and slide seat forward

or backwards as needed. Once the seat is lined up properly,

tighten the nuts to hold in place.

8. Connect the open end of the Bidet Hose to the T-valve.

NOTE: For those with mobility issues, we recommend our Swash 1400

or Swash 1000 bidet seats, as their mounting systems are engineered

for the most secure transitions from wheelchairs or walkers.

9. Turn On Water Supply

a. Open the main water supply valve slowly and check for leaks.

b. Wait 5 minutes, check again and, if there are no leaks, continue.

10. Plug the Power Cord into an electrical outlet. Nozzle will extend

and retract.

PRODUCT INSTALLATION

Swash Installation

c. Slide rubber cone washer, ﬂat washer, and then nut onto

mounting bolts under the toilet bowl and tighten to keep

mounting plate in place.

Step 7

Step 6

Step 8

NOTE: Make sure to only use a grounded GFCI (Ground Fault Circuit

Interrupter) electrical outlet. In the case of a short circuit, a grounded

GFCI outlet may help prevent electric shock or injury.

11. Follow instructions on page 16 for using the Swash.

13

NOTE: Customers with hard water, well water, and softened water can extend the

life of their bidet seat by purchasing and installing an external inline water ﬁlter

to be used with the Swash. The bidet ﬁlter should be changed every six months,

and can be purchased online at brondell.com.

PRODUCT INSTALLATION

External Bidet Filter Installation

1. Turn O Water Supply Valve and Flush Toilet.

a. Turn water valve o to stop the ﬂow of water.

b. Flush toilet and hold down handle to completely empty tank.

2. Disconnect the Bidet Hose from the T-valve.

3. Connect the female end of the Swash Filter to the open T-valve connection.

4. Connect the Bidet Hose to the male end of the Swash Filter.

5. Turn the toilet water supply valve back on.

Step 2

FLOW

Step 3

FLOW

Step 4

14

Nozzle Cleaning Button 9

Pulse Button 6

Seat Temperature Button 8

Nozzle Position Controls 7Water Pressure and

Dryer Temperature Controls

Gentle Mode Button

Water Temperature Button

Eco Mode Button

1

Stop Button

3

Front Wash /

Move Button

2

Rear Wash /

Move Button

4

Strong Wash /

Move Button

Dry Button 5

OPERATING THE SWASH

CSG15 Control Panel

10

11

12

13

15

1. Stop Button

Stops all wash and dry functions

currently operating.

2. Rear Wash / Move Button

Press once to initiate a rear wash. Press

again to initiate nozzle oscillation (repetitive

forward and backward nozzle movement).

3. Front Wash / Move Button

Press once to initiate a front wash. Press

again to initiate nozzle oscillation (repetitive

forward and backward nozzle movement).

4. Strong Wash / Move Button

Press once to initiate a strong wash. Press

again to initiate nozzle oscillation (repetitive

forward and backward nozzle movement).

5. Dry Button

Press once to initiate a two-minute Warm

Air Dryer cycle.

6. Pulse Button

Pressing this button while a wash is

running enables the water to repeatedly

increase and decrease in pressure in a

pulsating pattern.

7. Nozzle Position Buttons

Press the up and down arrow buttons to

adjust the nozzle position forward and

backward during a wash cycle.

8. Seat Temperature Button and Indicators

Press and release the Seat Temp button

to adjust the seat temperature to one of

four settings (Low: 93.2°F, Medium: 100.4°F,

High: 107.6°F, and O). Settings will be

saved for the next use.

OPERATING THE SWASH

CSG15 Control Panel

9. Nozzle Cleaning Button

Press this button to initiate Nozzle Cleaning

when not sitting on the seat, or while seat

sensor is deactivated. For more nozzle

maintenance see page 20.

10. Eco Mode Button and Indicator

Press and release the Eco Mode button to

select between two energy-saving options

(Standard, High-Eciency). See page 17 for

more information.

11. Water Temperature Button and Indicators

Press and release the Water Temp button

to adjust the outgoing water temperature to

one of four settings (Low: 91.4°F,

Medium: 96.8°F, High: 102.2°F, and O).

Settings will be saved for the next use.

12. Water Pressure and

Dry Temperature Controls

Press the “+” and “–” buttons to increase

and decrease the outgoing water

pressure to one of ﬁve settings. Pressing

these buttons while the Warm Air

Dryer is operating will adjust the drying

temperature. For Front Wash, Rear Wash

and Dry, settings will be saved for next

use. For Strong Wash, the highest pressure

settings will default for all uses.

13. Gentle Mode Button

Press this button to initiate a two-minute

gentle wash cycle followed by a two-minute

dry cycle. See page 16 for more information.

16

Prepare for Wash

Sit on the seat to ensure skin-to-seat contact

on the Seat Sensor. Once contact is made the

water pressure indicator lights will turn on.

Warm Water Wash

When ready to wash, press the Rear Wash,

Front Wash, or Strong Wash button on

the control panel one time to initiate a wash.

The nozzle will self-clean, extend into

the toilet bowl, spray for two minutes, turn o

automatically, retract, and self-clean once again.

1. Pressing the Rear Wash, Front Wash, or

Strong Wash button a second time while

the wash is running will cause the nozzle to

oscillate forward and backward, providing

a wider range of wash spray. Press again to

cancel the Move function.

2. While washing, users can adjust the water

temperature, pressure, and nozzle position

settings, as well as initiate the Pulse feature

by following the notes on page 15.

3. If you would like to stop the wash before the

two-minute cycle ends, press the Stop button

to discontinue water ﬂow.

4. After extended use the water may decrease

in temperature if a Low, Medium, or High

water temperature setting is selected. To

regain warmer water, stop all wash functions

for three minutes to allow the bidet to reheat

the water.

NOTE: The wash functions will not work

unless the sensor in the seat detects someone

sitting down (with the built-in skin conductivity

sensor). To override the Seat Sensor, please

see the instructions on page 17.

OPERATING THE SWASH

Using the CSG15

Warm Air Dryer Function

Press the Dry button to activate the Warm Air

Dryer. The dryer will run for two minutes and

turn o automatically.

1. While the air dryer is operating, users

can adjust the dryer temperature to a

comfortable level using the Dry Temp “+”

and “–” buttons. The dry temperature will be

reﬂected on the ﬁve indicator LEDs.

2. If you would like to stop the dryer before the

two minutes has elapsed, press Stop.

Gentle Mode

All settings within Gentle Mode are 40%

softer than standard wash modes.

Once activated, gentle mode will begin a

two-minute wash including:

• Full nozzle extension

• Water Pressure set to low

• Front Wash for one minute, Nozzle

Oscillation for 30 seconds, then Pulse

for 30 seconds

After the wash cycle is over, Gentle Mode will

initiate a two minute Warm Air Dry cycle on

Level Two.

NOTE: While the Gentle Mode cycle is running,

the Water Pressure setting is adjustable. Dryer

settings are also adjustable during the Gentle

Mode.

17

OPERATING THE SWASH

Special Mode Operations

Eco Mode

In this mode, the water in the tank and the seat temperature can be reduced to one of

two dierent energy-saving settings.

Standard Eco Mode: Press the Eco Mode button until the yellow indicator light is on for

Low energy-saving, and the seat and water temperature will be heated to 89.6 °F. Once

a person sits on the bidet, the Swash will revert to the last seat and water temperature

settings used. Press the Eco Mode button until there are no indicator lights on to

deactivate Eco Mode.

High-Eciency Eco Mode: Press the Eco Mode button until the green indicator light is

on for High energy-saving, and the seat and water temperature will turn o when the

bidet is not in use. Once a person sits on the bidet, the Swash will revert to the last seat

and water temperature settings used. Press the Eco Mode button until there are no

indicator lights on to deactivate Eco Mode.

Sitz Bath Mode

In Sitz Bath Mode, water pressure is switched to the lowest level regardless of the

preset water pressure settings. To initiate Sitz Bath Mode, while in a front or rear wash

cycle, press the Nozzle Cleaning button. Sitz Bath Mode will automatically run for ﬁve

minutes. The Nozzle Cleaning LED on the side arm will light up indicating Sitz Bath

Mode is on. To stop the Sitz Bath Mode before the end of the ﬁve-minute cycle, press

the Nozzle Cleaning button.

Seat Sensor Override

1. To activate the Seat Sensor Override, press and hold the Pulse button for four seconds.

A beep will sound to indicate that the seat sensor has been turned o. If the Swash is in

Silent Mode, there will not be a beep. The Nozzle Position and Water Pressure/Dry Temp

lights will stay on as long as Seat Sensor Override is activated.

2. To deactivate the Seat Sensor Override, press and hold the Pulse button for four seconds.

Two beeps will sound and the Nozzle Position and Water Pressure/Dry Temp lights will

turn o.

NOTES

• Activation or deactivation of Seat Sensor Override is not possible when seated.

• The Swash cannot be put into Silent Mode while Seat Sensor Override is activated.

• Nozzle Cleaning function will not work when Seat Sensor Override is activated. To initiate Nozzle

Cleaning you must ﬁrst deactivate Seat Sensor Override.

18

OPERATING THE SWASH

Special Mode Operations

Activating / Deactivating Silent Mode

1. To activate Silent Mode, press and hold the

“ – “ Water Pressure/Dry Temp button for

four seconds. A beep will sound to indicate

that Silent Mode has been activated.

2. To deactivate Silent Mode, press and

hold the “ – “ Water Pressure/Dry Temp

button for four seconds. Two beeps will

sound to indicate that Silent Mode has

been deactivated.

Activating / Deactivating Nightlight

The Nightlight is activated at the factory

by default.

1. To deactivate the Nightlight, press and hold

“+” for four seconds. This function cannot be

performed while sitting on the seat.

2. To activate the Nightlight, press and hold

“+” for four seconds. This function cannot

be performed while sitting on the seat.

Sleep Mode

In Sleep Mode, the Swash essentially

powers down. The Nightlight and the side arm

lights, the seat heater and the water heater will

turn o.

1. To activate Sleep Mode, press and hold the

Stop button for four seconds. The unit will

power down.

2. To awaken the Swash from Sleep Mode,

press the Stop, Front, or Strong button.

Factory Default Reset

It is possible to reset the Swash to Factory

Default settings.

To reset the Factory Default settings, press

and hold the Stop button for ten seconds. A

beep will sound at two seconds indicating the

beginning of the reset process and another

beep will sound at four seconds indicating the

reset is activated.

Automatic Tank Draining

1. To prevent stagnation, water in the warm

water storage tank can be set to drain and reﬁll

itself if the seat hasn’t been used in 48 hours.

2. To program this feature, press “Stop” and

“Water Temp.” at the same time and hold

buttons for four seconds.

La page charge ...

brondell CSG15 Le manuel du propriétaire

Ce manuel convient également à

brondell CSG15 Le manuel du propriétaire

dans d''autres langues

Documents connexes