Princess auto 8046492 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
User Manual
Please read and understand all instructions before use.
Retain this manual for future reference.
8046492
Powerst Floor
Model Abrasive
Blasting Cabinet
V 2.9
3
Visit www.princessauto.com for more information
8046492
Powerst Floor
Model Abrasive
Blasting Cabinet
V 2.9
SPECIFICATIONS
Material Heavy steel construction
Average Air Consumption 9.5 CFM @ 90 PSI
Operating Pressure 80 to 120 PSI
INTRODUCTION
Place parts to be blasted in the cabinet and close the door. With hands in the cabinet gloves, aim the
power gun at the object. Pull the trigger and let our unique siphon recycling system do the rest. Rust,
paint and scale are quickly removed, leaving the original metal clean and intact. Abrasive drops to the
bottom of the cabinet for continual recycling each time the power gun is activated.
IMPORTANT SAFETY PRECAUTIONS
WARNING! Read and understand all instructions before using this tool. The operator must follow basic
precautions to reduce the risk of personal injury and / or damage to the equipment. Before allowing
someone else to use this tool, make sure they are aware of all safety information.
NOTE: Keep this manual for the safety warnings, precautions and operating, inspection and maintenance
instructions. When this manual refers to a part number, it refers to the included parts list.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean and well lit.
2. Do not use in the presence of flammable gases or liquids.
3. Keep anyone not wearing the appropriate safety equipment away from the work area.
NOTE: Minimize distractions in the work environment. Distractions can cause you to lose control of
the tool.
4. Store tool properly in a safe and dry location to prevent rust or damage.
5. Always lock up tools and keep them out of the reach of children.
Powerfist Floor Model Abrasive Blasting Cabinet
4For technical questions call: 1-800-665-8685
8046492V 2.9
PERSONAL SAFETY
CAUTION! Wear protective equipment approved by the Canadian Standards Association (CSA) or
American National Standards Institute (ANSI) when using the Floor Model Sandblast Cabinet.
1. Dress properly; wear protective equipment. Use breathing, ear, eye, face, foot, hand and head
protection. Always wear ANSI approved impact safety goggles, which must provide both frontal
and side protection. Protect your hands with suitable gloves. Wear a full face shield if your
work creates metal filings or wood chips. Protect your head from falling objects by wearing a
hard hat. Wear an ANSI approved dust mask or respirator when working around metal, wood
and chemical dusts and mists. Wear ANSI approved earplugs. Protective, electrically non-
conductive clothes and non-skid footwear are recommended when working. Wear steel-toed
boots to prevent injury from falling objects.
2. Control the tool, personal movement and the work environment to avoid personal injury or
damage to the tool. Stay alert, watch what you are doing.
a. Keep articles of clothing, jewelry, hair, etc., away from moving parts to avoid entanglement
with a tool.
b. Do not operate any machine / tool when tired or under the influence of drugs,
alcohol or medications.
c. Do not overreach when operating a tool. Proper footing and balance enables better control
of a tool in unexpected situations.
d. Use clamps or other practical ways to support or secure the work piece to a stable
platform. Holding the work piece by hand or against your body is not stable and may lead
to loss of control and injury.
SPECIFIC SAFETY PRECAUTIONS
ABRASIVE BLASTING MEDIA
The blasting process emits abrasive media under pressure that breaks apart upon impact. The resulting
dust is a combination of the media and the material being removed by the abrasive. Both the media and
the material being removed may have toxic components such as lead in paint.
1. Check the abrasive media’s Material Safety Data Sheet (MSDS) for information on the health
risks and preventative measure that can be taken to minimize those risks.
2. Determine the toxicity of the material being removed and take appropriate measures.
3. Work in a ventilated area whenever possible.
4. Wear NIOSH approved respirators that protect both the lower face and eyes during blasting
operations whenever possible.
WARNING! Sand or silica particle dust can result in the lung disease known as silicosis, when
inhaled over a short period of time. Silicosis causes shortness of breath, cough, fever and bluish skin
(cyanosis). Seek immediate medical attention if these symptoms appear.
Powerfist Floor Model Abrasive Blasting Cabinet
5
Visit www.princessauto.com for more information
8046492 V 2.9
TOOL USE AND CARE
WARNING! Do not use the tool if the trigger or ON / OFF switch does not function properly. Any tool
that cannot be controlled with the ON / OFF switch is dangerous and must be repaired.
1. Use the correct tool for the job. Maximize tool performance and safety by using the tool for its
intended task.
2. Do not modify this tool or use for a purpose for which it was not designed.
3. This tool / device was designed for a specific function.
Do Not:
a. Modify or alter the floor model abrasive blasting cabinet; all parts and accessories are
designed with built-it safety features that may be compromised if altered.
b. Use the floor model abrasive blasting cabinet in a way for which it was not designed.
4. Avoid unintentional starts. Be sure the trigger is in the neutral position when not in use and
before connecting it to any air source.
5. Maintain the floor model abrasive blasting cabinet with care (see Maintenance).
AIR COMPRESSOR
Ensure the compressor used with the floor model abrasive blasting cabinet can supply the required Cubic
Feet per Minute at the required PSI (see Specifications).
1. Use proper size and type of air pressure
line and fittings.
2. Use only clean, dry, regulated
compressed air at the rated range as
marked on the tool.
CAUTION! Do not use an air source besides
an air compressor to power this tool.
3. Always use an air regulator, an
in-line filter and a moisture trap in
your compressed air system. These
accessories will increase the tool’s life
and keeps the tool in good working
condition. See the diagram for
recommended components of an airline.
4. Avoid using an air hose that is too long.
The longer the hose, the lower the
pressure that reaches the tool possibly causing it to cease functioning. As well, a longer hose
can become a tripping hazard.
5. Air Tool CFM consumption ratings are based upon a 25% duty cycle. If you require continuous
duty, a larger compressor will be required. See Specifications for the tool’s continuous
duty limit.
Powerfist Floor Model Abrasive Blasting Cabinet
6For technical questions call: 1-800-665-8685
8046492V 2.9
AIR SOURCE INSTALLATION
WARNING! Never use pure oxygen, carbon dioxide, combustible gases or any bottled gas as an air
source for a tool. Such gases are capable of causing an explosion and serious injury to persons.
1. Set the air pressure regulator on the air compressor to 90 PSI. Do not exceed the floor model
abrasive blasting cabinet's recommended air pressure. Excess pressure could result in damage
to the tool, to your work piece or serious personal injury.
2. Prepare a standard 1/4 in. air connector for use with your tool. Wrap the threaded portion of
the air connector with thread seal tape. Wrap in a clockwise direction so it will not unravel when
attaching to a quick connector. Attach it to the floor model abrasive blasting cabinet's air inlet
and tighten.
3. Attach a standard quick connector to the air source’s hose. Attach the air hose to the
tool’s air connector.
4. Check the air line and its connections for air leaks. Do not use the floor model abrasive blasting
cabinet until you have repaired all air leaks.
DISCONNECTING AIR SOURCE
WARNING! Failure to follow these steps could result in severe injury, tool or property damage.
Disconnect the floor model abrasive blasting cabinet from air source before cleaning, servicing, changing
parts / accessories or when not in use.
1. Turn the air regulator to the OFF or L position.
2. Turn off the air compressor.
3. Disconnect the air pressure hose.
4. Discharge any residual pressure inside the floor model abrasive blasting cabinet.
Powerfist Floor Model Abrasive Blasting Cabinet
7
Visit www.princessauto.com for more information
8046492 V 2.9
ABRASIVE BLASTING MEDIA
There are a number of different abrasive media the floor model abrasive blasting cabinet can use as an
abrasive. Each type of abrasive has a different application and effect on the object being blasted. Each
abrasive may also have hazards or health issues associated with their use.
NOTE: Read the ABRASIVE BLASTING MEDIA under SPECIFIC SAFETY PRECAUTIONS before use and
consult the Material Safety Data Sheet for each abrasive media product.
Recommended Abrasive Blasting Media:
a. Aluminum Oxide
b. Glass Bead
c. Steel Shot
d. Copper Slag
Not Recommended Abrasive Blasting Media:
These Blasting Medias clog easier and require different nozzles and higher pressures.
a. Baking soda, grain starch
b. Crushed nutshells
Material types:
1. Mineral: Sand or silica (see Safety section), garnet, magnesium sulphate.
a. Sand should be avoided, as there are other abrasives that perform the same or better
without the detrimental health effects.
2. Organic: Crushed nutshells.
3. Synthetic: Baking soda, grain starch.
4. Engineered: Aluminum oxide, glass beads.
5. Metal: Shot or grit made from steel, copper, aluminum or zinc.
NOTE: Store abrasive in a dry location. Wet abrasive will clog sandblasters.
UNPACKING
1. Carefully remove the floor model abrasive blasting cabinet from the package.
a. Retain packing material until you have carefully inspected and satisfactorily installed or
operated the floor model abrasive blasting cabinet.
2. Make sure that all items in the parts list are included.
3. Inspect the parts carefully to make sure the floor model abrasive blasting cabinet was not
damaged while shipping.
Powerfist Floor Model Abrasive Blasting Cabinet
8For technical questions call: 1-800-665-8685
8046492V 2.9
ASSEMBLY
CABINET INSTALLATION
1. Connect roof (#16) with front plate (#17) and rear plate (#19) using M5x12 screws with flange
(#47), M5 hex nuts with flange (#53) and Ø5 flat washers (#45).
2. Connect the left plate (#18) and the right plate (#15) to the roof assembly using M5x12 screws
with flange (#47), M5 hex nuts with flange (#53) and Ø5 flat washers (#45). Tighten all screws
and nuts. Place the cabinet on a table or bench.
FUNNEL INSTALLATION
1. Connect the funnel’s four sides (#6, #7) using M5x12 screws with flange (#47), M5 hex nuts
with flange (#53) and Ø5 flat washers (#45).
INSTALLATION
1. Place the cabinet on its back on a table or bench. Connect the funnel bottom plate (#9), screen
frame (#10) to the cabinet using M6x25 screws (#44), M6 hex nuts with flange (#52) and Ø6
flat washers (#57). Tighten all screws and nuts.
2. Put the screen (#11) on the funnel through the door of the cabinet.
3. Push the feet (#32) into the bottom of the legs (#1).
4. Connect the legs (#1) with the cabinet and shelf (#2) using M6x12 screws (#43), M6 hex nuts
with flange (#52) and Ø6 flat washers (#57). Secure them in place.
Powerfist Floor Model Abrasive Blasting Cabinet
9
Visit www.princessauto.com for more information
8046492 V 2.9
5. Fix section flange (#22), switch box (#20) onto the left plate of the cabinet (#18) and fix lock
(#12) onto the front plate of the cabinet (#17) using M4x10 screws (#50), M4 hex nuts (#54)
and Ø4 flat washers (#56) separately.
6. Fix the glove seal rings (#30) and glove mounting rings (#33) on the front plate of the cabinet
(#17) using M4x16 screws (#48), M6 hex nuts (#54) and Ø4 flat washers (#56). Fit the gloves
(#14) on the mounting rings (#33) with clamps (#31).
7. Set the seal ring (#23) in the hole of the cabinet back (#19) and slip the large cover (#36)
into place.
8. Affix the thick foam sealant tape around the inside of the door (#13). Attach the door (#13) to
the rear plate of the cabinet back (#19) using M5x12 screws with flange (#47), M5 hex nuts
with flange (#53) and Ø5 flat washers (#45).
9. Affix the thin foam sealant tape to the glass (#28), between the frame and the glass. Connect
the frame (#28), glass (#27), Plexiglas (#26), protection film (#25) with the roof of the cabinet
(#16) using M4x20 screws (#49), M4 hex nuts (#54) and Ø4 flat washers (#56).
NOTE: Itmay be necessary to seal the hopper with a silicon sealant to preventleaking ofblast media.
CONNECTING THE AIR HOSE
1. Your shop air hose is connected to the air inlet of the power gun. Bottom handle of the gun has
1/4 in. NPT pipe threads which will fit most air hose. The cabinet pickup tube leads to the clear
siphon hose, which connects to the gun head assembly.
WARNING! DO NOT operate the blasting system at or over 120 PSI.
2. At the right front of the cabinet is an opening for the air hose from your compressor. An
ordinary 3/8 in. I.D. air hose should fit through this opening. Connect your air hose to the
bottom handle of the power gun by screwing into place (using Teflon tape or pipe compound –
do not over tighten). Close the door and pull the trigger a few times to test the operation. You
are now ready to add abrasive.
3. Add suitable abrasive by pouring through the side door opening and allowing it to fill the funnel
area. Do not overfill (1/2 full below the work area screen is best.)
NOTE: Use a fine grade of abrasive to prevent clogging.
OPTIONAL ACCESSORIES
The following accessories are available separately for the floor model abrasive blasting cabinet. Please
contact your nearest Princess Auto location for details:
1. Interior fluorescent light (#39) (8012802)
2. 12VDC adapter (8012795)
3. Replacement ceramic nozzles (8026717)
4. Replacement window film (8578759)
5. Replacement abrasive blasting gloves (8133043)
Powerfist Floor Model Abrasive Blasting Cabinet
10 For technical questions call: 1-800-665-8685
8046492V 2.9
OPERATION
WARNING! Before you begin using the abrasive blasting cabinet, make sure that the vent plug and
the intake plug are in the OPEN position. Failure to follow these steps could result in severe personal
injury, tool or property damage.
1. Place the part you wish to abrasive blast in the cabinet. Always close and latch the lid after
placing the part in the cabinet prior to blasting. Severe injury to the skin and eyes may result
from exposure to the blast stream, as well as other health concerns.
2. After putting your hands into the gloves, firmly grasp the gun and depress the trigger. This
should begin the abrasive flow. If no flow is seen, you may need to clear the intake tube. Simply
move it around inside the cabinet to dislodge any blockage. If this does not work, try dislodging
the media with a drill bit held in your hand. You need to discard the moist media.
3. Now you may begin finishing your part. You should move the blast stream continuously over
the part in an even and circular motion. To avoid undesirable peening, the flow should not be
too hard or concentrated.
MAINTENANCE
NOTE: Disconnect power and air before performing any maintenance.
PLUGGED CONDITIONS
All blasting systems are prone to plugging or wear because of the abrasive material used. The following
items should be checked as indicated:
1. The blast nozzle may become plugged from moist media. Try dislodging the media with a drill
bit held in your hand. You need to discard the moist media.
2. If the abrasive pick-up hose appears plugged, simply move it around inside the cabinet to
dislodge any blockage. If this does not work, try dislodging the media with a drill bit held in
your hand. You need to discard the moist media. Dust may fly up when you do this so make
sure the lid is down!
WEAR CONDITIONS
This is usually noted when an excessive amount of dust appears in the cabinet. Dust will occur if:
1. The abrasive blasting media is worn out if it has lost its granular or spherical appearance or has
a lot of debris mixed in from the parts being blasted, replace it. This is usually noticed when the
abrasive media that exits the nozzle resembles more of a cloud than a stream.
2. The air outlet vent is plugged or airflow out is blocked. Cleaning this vent should help reduce
dust in the cabinet. The gun parts may wear out. This is usually evident when the blast pattern
is too wide and ineffective; simply replace the nozzle or orifice.
Powerfist Floor Model Abrasive Blasting Cabinet
11
Visit www.princessauto.com for more information
8046492 V 2.9
TO REPLACE THE TRANSPARENT ACRYLIC GLASS
At the bottom of the transparent top lid, there is a 0.5 mm replaceable acrylic glass window. If the
transparent acrylic glass window is becoming unclear, it may be replaced with a new one to avoid
affecting vision during work.
GENERAL MAINTENANCE
Before making any adjustments or changing any accessory, turn off the tool and unplug it from
its air source.
1. The nozzle will wear away over time, causing the internal diameter to widen and disperse the
media over a larger area, reducing the tool’s efficiency. The compressor will also need to work
harder to maintain the pressure. Check at regular intervals and replace as appropriate.
2. Always check for cracks and leaks in the gun, hose, and tanks. These problems must be fixed
immediately due to the dangers involved with air under pressures.
3. Check for damaged parts. Before using any tool, any part that appears to be damaged should
be carefully checked to determine that it would operate properly and perform its intended
functions. Check for alignment and binding of moving parts, for broken parts or mounting
fixtures, or for any other condition that may affect proper operation.
4. Use only identical replacement parts or accessories intended for use with this tool when
servicing. Replace damaged parts immediately.
5. Keep the tool clean. Wipe the tool with a clean cloth and periodically blow out all areas with
compressed air. If compressed air is not available, use a brush to remove dust from areas. Do
not use harsh chemicals or solvents to clean the tool. These chemicals could seriously damage
the housing.
Powerfist Floor Model Abrasive Blasting Cabinet
12 For technical questions call: 1-800-665-8685
8046492V 2.9
6. Regularly inspect all mountings and screws to ensure tightness. Should any screws become
loose, tighten immediately.
7. If repairs are required, bring your tool to Princess Auto Ltd.
LUBRICATION
Do not use lubricants or air tool oil on the floor model abrasive blasting cabinet. The oil will contaminate
the abrasive media, clogging the tool and reducing the effectiveness of the abrasive.
DISPOSING OF THE TOOL
1. If your floor model abrasive blasting cabinet has become damaged beyond repair, do not throw
it out. Take it to the appropriate recycling facility.
2. Abrasive can be re-used until it eventually breaks down or becomes dusty. To discard worn
abrasive, simply place an empty box under the spring loaded trap door to catch the
discarded abrasive.
Powerfist Floor Model Abrasive Blasting Cabinet
13
Visit www.princessauto.com for more information
8046492 V 2.9
TROUBLE SHOOTING
When repairs are needed, bring the tool to the nearest Princess Auto Ltd. If unable to do so, have a
qualified technician service the tool.
Problem Possible Causes Suggested Solutions
Excessive dust in the cabinet. 1. Exhaust plugged or air
flow is blocked.
2. Abrasive media worn.
3. Too much abrasive
media inside.
4. Loose air line or
fitting connections
1. Clean rear vent and keep vent
away from any wall.
2. Replace abrasive media.
3. Remove excess media.
4. Tighten fitting and make sure air
lines are secure.
Uneven blasting actions. 1. Too much abrasive media
inside the cabinet.
2. Moisture present inside
the cabinet.
1. Remove excess media.
2. Check air line to make sure there
is no moisture in it.
Inadequate speed or inefficiency
of blast.
1. Abrasive media worn.
2. Pressure too low.
3. Worn nozzle.
1. Replace abrasive media.
2. Increase inlet pressure and
check that the control valve
is fully opened.
3. Replace nozzle.
Static electricity. 1. Dry weather conditions. 1. Leave the item being cleaned on
the grating.
Powerfist Floor Model Abrasive Blasting Cabinet
14 For technical questions call: 1-800-665-8685
8046492V 2.9
PARTS BREAKDOWN
Powerfist Floor Model Abrasive Blasting Cabinet
15
Visit www.princessauto.com for more information
8046492 V 2.9
PARTS LIST
No. Description Qty.
1 Leg 4
2 Shelf 1
3 E Hook 1
4 Removal Cover 1
5 Funnel Mouth 1
6 Funnel Plate (Front, Rear) 2
7 Funnel Plate (Left, Right) 2
8 Gun 1
9 Bottom Plate 1
10 Screen Frame 1
11 Mesh Screen 1
12 Latch 1
13 Door 1
14 Glove 2
15 Right Plate 1
16 Roof 1
17 Cabinet Front Plate 1
18 Cabinet Left Plate 1
19 Cabinet Rear Plate 1
20 Switch Box 1
21 Switch 1
22 Connection Flange 1
23 Seal Ring 1
24 Hinge 1
25 Protection Film 1
26 Plexiglas 1
27 Plexiglas 1
28 Frame 1
29 Small Cap 1
30 Glove Seal Ring 2
No. Description Qty.
31 Glove Clamp 2
32 Feet 4
33 Glove Mounting Ring 2
34 Leg Shim 3
35 Metal Liner 1
36 Large Cap 1
37 Daylight Lamp Mounting Ring 1
38 Phillips Screw M4 x 12 11
39 Interior Fluorescent Light 1
40 --- ---
41 Phillips Screw M6 x 45 2
42 Hex Nut M5 1
43 Phillips Screw M6x12 24
44 Phillips Screw M6x25 14
45 Flat Washer Ø5 62
46 Phillips Screw M5x50 1
47 Phillips Screw with Flange M5x12 61
48 Phillips Screw M4x16 12
49 Phillips Screw M4x20 12
50 Phillips Screw M4x10 11
51 Phillips Screw M2x10 2
52 Hex Nut with Flange M6 40
53 Hex Nut with Flange M5 61
54 Hex Nut M4 35
55 Hex Nut M2 2
56 Flat Washer Ø4 35
57 Flat Washer Ø6 40
58 Door Seal 1
8046492
Manuel d'utilisateur
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
V 2,9
Coffret de projection
abrasive Powerst,
modèle de plancher
3En cas de questions techniques, appelez le 1-800-665-8685
8046492V 2,9
Coffret de projection
abrasive Powerst,
modèle de plancher
SPÉCIFICATIONS
Matériau Construction en acier résistent
Consommation d'air moyenne 9,5 pi cube/min à 90 lb/po carré
Pression d'utilisation 80 à 120 lb/po carré
INTRODUCTION
Placez les pièces à grenailler dans le cabinet et fermez la porte. Placez les mains dans les gants du cabinet
et dirigez le pistolet vers l’objet. Appuyez sur la gâchette et laissez notre système unique de recyclage à
siphon faire le reste. La rouille, la peinture et la calamine s’enlèvent rapidement, laissant ainsi le métal
d’origine propre et intact. L’abrasif tombe au bas du cabinet pour assurer un recyclage continu chaque
fois qu’on actionne le pistolet électrique.
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant d’utiliser cet outil.
L’utilisateur doit respecter les précautions de base lorsqu’il utilise cet outil afin de réduire le risque
de blessure et/ou de dommage à l’équipement. Avant de permettre à un autre individu d’utiliser cet
outil, assurez-vous qu’il est avisé de toutes les consignes de sécurité.
REMARQUE : Conservez ce manuel qui contient les avertissements de sécurité, les précautions et les
instructions de fonctionnement, d’inspection et d’entretien. Lorsque ce manuel fait référence à un numéro
de pièce, il fait référence à la liste des pièces comprises.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre aire de travail propre et
bien éclairée.
2. N’utilisez pas d’outils électriques en présence de gaz ou de liquides inflammables.
3. Assurez-vous que les personnes qui ne portent pas l’équipement de sécurité approprié ne se
trouvent pas à proximité de l’aire de travail.
Coffret de projection abrasive Powerfist, modèle de plancher
4En cas de questions techniques, appelez le 1-800-665-8685
8046492
V 2,9
REMARQUE : Minimisez les distractions au sein de l’environnement de travail. Les
distractions peuvent causer une perte de contrôle de l’outil.
4. Rangez l’outil correctement dans un lieu sécurisé et sec pour empêcher la rouille ou
les dommages.
5. Gardez toujours les outils dans un endroit verrouillé et hors de la portée des enfants.
SÉCURITÉ PERSONNELLE
ATTENTION ! Portez de l’équipement de protection homologué par l’Association canadienne de
normalisation (CSA) ou l’American National Standards Institute (ANSI) quand vous utilisez le modèle
de plancher du cabinet de sablage.
1. Portez des vêtements appropriés et de l’équipement de protection. Utilisez des protections pour
les voies respiratoires, les oreilles, les yeux, le visage, les pieds, les mains et la tête. Portez
toujours des lunettes de sécurité étanches approuvées par l’ANSI qui offrent une protection
frontale et latérale. Protégez-vous les mains à l’aide de gants appropriés. Portez un écran facial
panoramique si votre travail produit des limailles ou des copeaux de bois. Protégez-vous la
tête de la chute d’objets en portant un casque de protection. Portez un masque antipoussières
ou un appareil respiratoire approuvé par l’ANSI lorsque vous travaillez où il y a des poussières
et des vapeurs provenant du métal, du bois ou de produits chimiques. Portez des bouchons
d’oreille approuvés par l’ANSI. Des vêtements de protection non conducteurs d’électricité et des
chaussures antidérapantes sont recommandés pour le travail. Pour éviter les blessures dues
aux chutes d’objets, portez des chaussures à embout d’acier.
2. Gardez le contrôle de l’outil, de vos mouvements et de l’environnement de travail pour éviter
les blessures ou le bris de l’outil. Restez alerte, portez attention à vos gestes et faites preuve de
bon sens.
a. Tenez les vêtements, les bijoux, les cheveux, etc. à l’écart des pièces mobiles pour éviter
de les faire coincer par l’outil.
b. N’utilisez pas d’appareil ou d’outil si vous êtes fatigué ou sous l’effet de drogues, d’alcool
ou de médicaments.
c. N’utilisez pas l’outil si vous devez étirer les bras pour le faire. Une stabilité et un équilibre
appropriés sont nécessaires afin d’avoir un meilleur contrôle de l’outil en cas de
situations inattendues.
d. Utilisez des pinces ou un autre moyen pratique pour fixer la pièce à travailler sur une plate-
forme stable. Une pièce à travailler tenue dans les mains ou appuyée contre le corps n’est
pas stable et risque d’entraîner une perte de contrôle et des blessures.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
MATÉRIAUX DE SABLAGE ABRASIFS
Le travail de sablage produit des matériaux abrasifs sous pression qui éclatent au moment de l’impact.
La poussière produite est une combinaison de ces matériaux et du matériau enlevé par les particules
abrasives. Les particules abrasives et le matériau enlevé peuvent avoir des composants toxiques comme
du plomb dans la peinture.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Princess auto 8046492 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur

dans d''autres langues