Senix BLAX2-M Manuel utilisateur

Taper
Manuel utilisateur
20V MAX LITHIUM ION
CORDLESS AXIAL FAN BLOWER
Operator’s manual
Model: BLAX2-M
BLAX2-M-0
For customer support, please call 1-800-261-3981 or send email to:
SAVE THIS MANUAL FOR FUTURE REFERENCE.
ORIGINAL INSTRUCTIONS
TM
EN - 2 WWW.SENIXTOOLS.COM
12
3 4 5 7
6
8
9
1
23
Blower Tube Release Button
WWW.SENIXTOOLS.COM 3 - EN
4
6
5
Light Button
Cruise Control
On/Off Switch
Handle
EN - 4 WWW.SENIXTOOLS.COM
TABLE OF CONTENTS
SAFETY & INTERNATIONAL SYMBOLS ...........................4
SAFETY INSTRUCTIONS....................................................5
KNOW YOUR UNIT............................................................10
SPECIFICATIONS*.............................................................10
ASSEMBLY.........................................................................11
OPERATION.......................................................................11
MAINTENANCE..................................................................13
TROUBLESHOOTING.......................................................14
PARTS................................................................................15
WARRANTY........................................................................16
SAFETY & INTERNATIONAL
SYMBOLS
Explanation of Safety & international symbols describes
safety and international symbols and pictographs that may
appear on this product. Read the operator’s manual for
complete safety, assembly, operating and maintenance and
repair information.
Caution / Warning.
To reduce the risk of injury, user must read
instruction manual.
Wear eye protection.
Wear hearing protection.
Wear respiratory protection.
Do not use in rain or wet conditions.
Wear protective gloves.
Wear Sturdy, non-slip footwear.
Do not use in rain or wet conditions.
Keep all bystanders at least 50 ft. away.
Thrown objects can ricochet and result in
personal injury or property damage.
Do not dispose of battery packs in rivers or
immerse in water.
Do not dispose of battery packs in fire. They
will explode and cause injury.
Use and store the battery within an temperature
below 122°F(50°C).
Do not disassemble, crush, heat above
212°F(100°C) ; Never expose the battery to
microwaves or high pressures.
Indoor use only. Only use battery charger
indoors.
WWW.SENIXTOOLS.COM 5 - EN
SAFETY INSTRUCTIONS
WARNING!
This product can expose you to
chemicals including lead, a chemical
known to the State of California to
cause cancer and birth defects or
other reproductive harm. For more
information go to www.P65Warnings.
ca.gov.
WARNING!
Some dust created by power
sanding, sawing, grinding, drilling
and other construction activities
contains chemicals known to the
state of California to cause cancer,
birth defects or other reproductive
harm.Some examples of these
chemicals are:
Lead from lead-based paints,
Crystalline silica from bricks and
cement and other masonry products
and Arsenic and chromium from
chemically treated lumber.
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemical:
Work in a well ventilated area,
And work with approved safety
equipment,such as those dust
masks that are specially designed to
lter out microscopic particles.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING!
When using electric gardening
appliances, basic safety precautions
should always be followed to
reduce risk of re, electric shock,
and personal injury, including the
following:
SAVE THESE INSTRUCTIONS AND
REVIEW FREQUENTLY PRIOR
TO USE AND IN INSTRUCTING
OTHERS.
• Keep Children Away – All visitors
should be kept at a distance from
work area.
• Dress Properly – Do not wear
loose clothing or jewelry. They can
be caught in moving parts. Use
of rubber gloves and substantial
footwear is recommended when
working outdoors. Wear protective
hair covering to contain long hair.
• Use Safety Glasses – Always use
face or dust mask if operation is
dusty.
• Wear Appropriate Personal
Hearing Protection During Use
– Under some conditions and
duration of use, noise from this
product may contribute to hearing
loss.
• Use Right Appliance – Do not use
EN - 6 WWW.SENIXTOOLS.COM
tools normally spark, and the
sparks might ignite fumes.
Avoid Unintentional Starting –
Don’t carry the blower with nger
on switch. Be sure switch trigger is
in the locked or off position before
inserting battery pack.
• Don’t Force Appliance – It will
do the job better and with less
likelihood of a risk of injury at the
rate for which it was designed.
• Don’t Overreach – Keep proper
footing and balance at all times.
• Stay Alert – Watch what you are
doing. Use common sense. Do not
operate appliance when you are
tired.
• Store Idle Appliances Indoors
– When not in use, appliances
should be stored indoors in dry,
and high or locked-up place – out
of reach of children.
• Maintain Blower With Care – Keep
guard and handles clean for best
performance and to reduce the
risk of injury. Keep handles dry
and free from oil and grease.
BLOWER SAFETY WARNINGS
• The blower has been designed to
clear light debris and leaves from
hard surfaces – not for clearing
grassed areas.
• This blower is intended for
appliance for any job except that
for which it is intended.
• Disconnect Appliance –
Disconnect the appliance from the
power supply when not in use,
before servicing, when changing
accessories such as blades, and
the like.
• Check Damaged Parts – Before
further use of the leaf blower,
a guard or other part that is
damaged should be carefully
checked to determine that it will
operate properly and perform
its intended function. Check
for alignment of moving parts,
binding of moving parts, breakage
of parts, mounting and any
other condition that may affect
its operation. A guard or other
part that is damaged should be
properly repaired or replaced call
our customer service help line for
assistance.
• Lighting – Only operate blower in
daylight or good articial light.
• Don’t overreach – Keep proper
footing and balance at all times.
• Don’t Use In Rain.
Avoid Dangerous Environments
– Don’t use blower in rain, damp
or wet locations. Do not operate
blower in gaseous or explosive
atmospheres. Motors in these
WWW.SENIXTOOLS.COM 7 - EN
household use only. Commercial
use of this product is prohibited
and will void the manufacturer’s
warranty.
• Prevent unintentional starting.
Ensure the switch is in the
off-position before connecting
to battery pack, picking up or
carrying the appliance. Carrying
the appliance with your nger on
the switch or energizing appliance
that have the switch on invites
accidents.
• Disconnect the battery pack from
the appliance before making
any adjustments, changing
accessories, or storing appliance.
Such preventive safety measures
reduce the risk of starting the
appliance accidentally.
• When operating the unit, never
point the blower nozzle in the
direction of people or pets or in
the direction of windows. Use
extra caution when blowing debris
near solid objects, such as trees,
automobiles, and walls.
• Be sure to secure the unit when
transporting it.
• Never douse or squirt the unit
with water or any other liquid.
Clean the unit after each use as
described in the cleaning and
storage section.
• Carefully inspect your appliance
prior to use and follow all label
and marking instructions.
• Keep all parts of your body away
from any moving parts and all hot
surfaces of the unit.
• Do not put any object into the
tool’s openings. Do not use the
tool with any opening blocked;
keep openings free of dust, lint,
hair, or any other object that may
reduce air ow.
• Check the work area before each
use. Remove all objects such as
rocks, broken glass, nails, wire,
or string, which can be thrown
or become entangled in the
machine.
• Service on the product must
be performed by qualied
repair personnel only. Service
or maintenance performed by
unqualied personnel could result
in injury to the user or damage to
the product.
• Never run the unit without the
proper equipment attached.
Always ensure the blower tube is
properly installed.
Always grasp the handle when
operating the unit, only operate
the machine in its intended
orientation.
EN - 8 WWW.SENIXTOOLS.COM
may cause irritation or burns.
(This advice is considered correct
for conventional NiMh, NiCd, lead
acid and lithium-ion cell types. If
this advice is incorrect for a cell
design that differs from these,
then the correct advice may be
substituted.)
• Do not use a battery pack or
appliance that is damaged
or modied. Damaged or
modied batteries may exhibit
unpredictable behavior resulting in
re, explosion or risk of injury.
• Do not expose a battery pack
or appliance to re or excessive
temperature. Exposure to re or
temperature above 266°F(130°C)
may cause explosion.
• Follow all charging instructions
and do not charge the battery
pack or appliance outside of the
temperature range specied in the
instructions. Charging improperly
or at temperatures outside of the
specied range may damage the
battery and increase the risk of
re.
• Do not modify or attempt to repair
the appliance or the battery pack
(as applicable) except as indicated
in the instructions for use and
care.
BATTERY PACK AND BATTERY
CHARGER SAFETY WARNINGS
• Recharge only with the charger
specied by the manufacturer. A
charger that is suitable for one
type of battery pack may create a
risk of re when used with another
battery pack.
• Use appliances only with
specically designated battery
packs. Use of any other battery
packs may create a risk of injury
and re.
WARNING!
Use only the following type and size
battery: B25X2/B50X2.
• When battery pack is not in use,
keep it away from other metal
objects, like paper clips, coins,
keys, nails, screws or other small
metal objects, that can make a
connection from one terminal
to another. Shorting the battery
terminals together may cause
burns or a re.
• Under abusive conditions,
liquid may be ejected from the
battery; avoid contact. If contact
accidentally occurs, ush with
water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery
WWW.SENIXTOOLS.COM 9 - EN
EMERGENCY
Familiarize yourself with the use
of this product by means of this
instruction manual. Memorize the
safety directions and follow them to
the letter. This will help to prevent
risks and hazards.
1. Always be alert when using this
product, so that you can recognize
and handle risks early. Fast
intervention can prevent serious
injury and damage to property.
2. Switch off the product and
remove the battery pack if there
are malfunctions. Have the
product checked by a qualied
professional and repaired, if
necessary, before you operate it
again.
RESIDUAL RISKS
Even if you are operating this
product in accordance with all
the safety requirements, potential
risks of injury and damage remain.
The following dangers can arise in
connection with the structure and
design of this product:
1. Health defects resulting from
vibration emission if the product
is being used over long periods of
time or not adequately managed
and properly maintained.
2. Injuries and damage to property
due to broken attachments or the
sudden impact of hidden objects
during use.
3. Danger of injury and property
damage caused by ying objects.
4. Prolonged use of this product
expose the operator to vibrations
and may produce ‘whitenger
disease. In order to reduce the
risk, please wear gloves and keep
your hands warm. If any of the
‘whitenger symptoms appear,
seek medical advice immediately.
‘Whitenger symptoms include:
numbness, loss of feeling,
tingling, pricking, pain, loss of
strength, changes in skin colour
or condition. These symptoms
normally appear in the ngers,
hands or wrists. The risk increases
at low temperatures.
WARNING!
This product produces an
electromagnetic eld during
operation! This eld may under
some circumstances interfere with
active or passive medical implants!
To reduce the risk of serious or fatal
injury, we recommend persons with
medical implants to consult their
doctor and the medical implant
manufacturer before operating this
product!
SAVE THESE INSTRUCTIONS
EN - 10 WWW.SENIXTOOLS.COM
KNOW YOUR UNIT
APPLICATIONS
Model: BLAX2-M
As a blower:
Blowing leaves, garden waste such as grass, twigs and
pine needles.
1Blower tube
2Blower Tube Release Button
3Cruise Control
4On/Off Switch
5Handle
6Unlock Button of Battery Pack
7Battery Pack
8Air Inlet Cover
9Housing
NOTE:
BLAX2-M-0 does not include the charger and the battery
pack.
SPECIFICATIONS*
Model BLAX2-M
Input voltage 18V d.c.
No-load speed 0-16800RPM
Max. wind speed 80MPH
Max. wind volume 350CFM
Weight (without battery pack) 4.63lbs
Battery model for option B25X2 B50X2
Rated voltage 18V 18V
Rated capacity 2.5Ah 5.0Ah
Weight 0.74lbs 1.43lbs
Charger model CHX2
Rated input 100-240V ~ 50/60Hz
Rated output 21V, 2000mA
Charging time
(with 2.5 Ah battery) 85mins
Charging time
(with 5.0 Ah battery) 130mins
Protection class(for charger) / II
Weight 0.75lbs
Model BLAX2-M-0
Input voltage 18V d.c.
No-load speed 0-16800RPM
Max. wind speed 80MPH
Max. wind volume 350CFM
Weight (without battery pack) 4.63lbs
Battery model Not included
Charger model Not included
WWW.SENIXTOOLS.COM 11 - EN
ASSEMBLY
1. Unpack all parts and lay them on a at, stable surface:
2. Remove all packing materials and shipping devices, if
applicable.
3. The scope of delivery varies depending on the country
and purchased variant:
Model of BLAX2-M-0
Blower x1
Blower tube x1
Instruction manual x1
4. If you nd that parts are missing or show damage do
not use the product but contact your dealer. Using an
incomplete or damaged product represents a hazard to
people and property.
5. Ensure that you have all the accessories and tools
needed for assembly and operation. This also includes
suitable personal protective equipment.
NOTE:
BLAX2-M includes the charger and the battery pack.
BLAX2-M-0 does not include the charger and the battery
pack.
WARNING!
Wear protective gloves for this assembly work
and always lay the product on a flat and stable
surface while assembling.
Follow the assembly instructions step-by-step
and use the pictures provided as a visual guide
to easily assemble the product!
Do not insert the battery pack before the power
tool is completely assembled or adjusted!
INSTALLING THE BLOWER TUBE
WARNING!
To avoid serious personal injury and damage
to the unit, shut the unit off before removing or
installing an attachment.
Align and insert the blower tube. Make sure the blower
tube release button snaps into the slot on the blower tube
(Fig.2).
INSTALLING/REMOVING THE
BATTERY PACK
To install:
Align and slide the battery pack into the docking port until it
is locked in place (Fig.3).
To remove:
Press the unlock button on battery pack and remove the
battery pack from the product .
OPERATION
WARNING!
Inspect the tool for complete installation. Any
missing, damaged or misplace may cause
serious injury.
Wear protective equipments at all times while
operating the power tool.
SWITCHING ON/OFF
Hold the product as in working condition.
To start the product, either press the on/off switch to turn
the product on or dial the cruise control.
Dialing the cruise control clockwise locks the on/off switch
and keeps the machine at a constant speed.
To switch the product off, dial the cruise control
counterclockwise to the end can automatically release the
on/off switch and stop the product. If you starts the product
without using cruise control, just release the on/off switch
(Fig.4).
NOTE:
The product will continue to work for some time even after
the motor has been switched off! Wait until it comes to a
complete stop before putting the product down!
ADJUSTING BLOWING SPEED
Either press the on/off switch or dial the cruise control
clockwise can change the blower speed.
OPERATING HOURS
Only operate the product at reasonable hours - not early in
the morning, late at night or on weekends/ public holidays
when people might be disturbed. Inform yourself about local
restrictions.
EN - 12 WWW.SENIXTOOLS.COM
GENERAL
1. Double check that accessories or application tools are
properly xed.
2. Always hold the product on its handle. Keep the handle
dry and clean to ensure safe support.
3. Ensure that the air vents are always unobstructed
and clear. Clean them if necessary with a soft brush.
Blocked air vents may lead to overheating and damage
the product.
4. Switch the product off immediately if you are disturbed
while working by other people entering the working
area. Always let the product come to a complete stop
before putting it down.
5. Do not overwork yourself. Take regular breaks to ensure
you can concentrate on the work and have full control
over the product.
6. Before switching the product on, check whether it has
been assembled correctly and all the moving parts are
running smoothly!
7. While working, ensure that the product does not strike
hard objects, as this can cause damage.
8. Do not blow any solid bodies such as stones, branches,
pieces of branch or similar.
9. We recommend slightly dampening surfaces in dusty
conditions or using a mister attachment.
NOTE:
The risk of the operation may occurs, such as the sharp
tree branches may cut the user's skin, the blade of the unit
may hurt the user's body. Always wear eye, hearing, hand,
foot and body protection to reduce the risk of injury when
operating this unit.
BLOWING
1. Before blowing, loosen leaves that are stuck to the
ground using a broom or rake.
2. Hold the tube approximately 3.9inch(10cm) above
the ground and walk slowly forward using a sweeping
motion from side to side.
3. Direct the air stream away from yourself.
4. Ensure that you do not stir up any heavy objects and
hurt somebody or damage something.
NOTE:
When the blower vibrates abnormally, immediately shut
off the unit. Abnormal vibration often shows a mechanical
problem and continues use could result in injury or property
damage.
CHARGING THE BATTERY PACK
WARNING!
This Lithium-Ion battery pack is shipped partially
charged. Fully charge the battery pack before
using it for the first time.
NOTE:
Charge batteries at a ambient temperature of 32°F-104°F
(0°C-40°C) and always store batteries at a ambient
temperature of 32°F-77°F (0°C-25°C).
1. Charge the Lithium-Ion battery pack only with the correct
charger.
2. Connect the charger to a power supply, the light indicator
of the charger turns red.
3. Align the raised ribs of the battery pack with the slot in
the charger.
4. Insert the battery pack into the charger, the light indicator
of the charger turns green and it ashes (Fig.5).
5. The charger will communicate with the battery pack to
evaluate the condition of the battery pack.
6. It is fully charged that the four lights of the battery turn
on. Disconnect the power supply from the charger.
Remove battery pack from the charger.
CHARGING INDICATOR
Press the light button on the battery pack to check whether
it needs to charge (Fig.6) .
Lights
Status
Lighted Off Blinking
The battery is at full
capacity.
The battery is at 75%
capacity.
The battery is at 50%
capacity and requires
charging.
WWW.SENIXTOOLS.COM 13 - EN
The battery is at 25%
capacity and requires
charging soon.
The battery is less
than 5% capacity and
requires charging
immediately.
WARNING!
Malfunctions may occur when the four lights
blinking in turns.
OVERHEAT PROTECTION
When the tool/battery is overheated, the tool stops
automatically. In this situation, let the power tool/battery cool
before turning the tool on again.
OVERDISCHARGE PROTECTION
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the tool
and charge the battery.
MAINTENANCE
WARNING:
Always switch the product off, remove the
battery pack and let the product cool down
before performing cleaning and maintenance
work!
Always wear eye, hearing, hand, foot and body
protection to reduce the risk of injury when
operating this unit.
Only perform cleaning and maintenance work
according to these instructions! All further works
must be performed by a qualied specialist!
And only use specied spare parts for
replacement.
CLEANING
• Switch the product off, pull out the battery pack from the
product.
• Clean up debris from blower tube.
• Remove wood chips and other debris from air vents.
• Use a small brush to clean the outside of the unit. Do not
use strong detergents. Household cleaners that contain
aromatic oils such as pine and lemon, and solvents such
as kerosene, can damage plastic.
• Wipe off any moisture with a soft cloth. The tool should
never come in contact with water.
TRANSPORT
• Clean the product as described above.
Always carry the product by its handle.
• Protect the product from any heavy impact or strong
vibrations which may occur during transportation in
vehicles.
• Secure the product to prevent it from slipping or falling
over, damage or injury.
STORAGE
• Clean the product as described above.
• Store the product and its accessories in a dark, dry, frost-
free, well-ventilated place.
Always store the product in a place that is inaccessible
to children. The ideal storage temperature is between
50°F(10°C) and 86°F(30°C).
• We recommend using the original package for storage or
covering the product with a suitable cloth or enclosure to
protect it against dust.
NOTE:
To prolong battery life, never store battery pack in a
completely discharged condition. Make sure the battery
pack is charged once per year or when the LED indicator
shows only one light.
DISPOSAL
Waste product should not be disposed of with household
waste. Please recycle where facilities exist. Check with your
local authority or retailer for recycling advice.
Electrical products should not be discarded with
household products. Used electrical products
must be collected separately and disposed of at
collection points provided for this purpose. Talk
with your local authorities or dealer for advice
on recycling.
EN - 14 WWW.SENIXTOOLS.COM
TROUBLESHOOTING
Suspected malfunctions are often due to causes that the users can x themselves. Therefore, check the product using this
section. In most cases the problem can be solved quickly.
PROBLEM POSSIBLE CAUSE SOLUTION
Product does not start
Battery pack not properly attached Attach properly
Battery pack capacity too low Remove and charge battery pack
Battery pack damaged Check by a specialist electrician
On/off switch not set on ON
position Refer to chapter “SWITCHING ON/OFF”
Product does not reach full power
Battery pack capacity too low Charge battery pack
Air vents are blocked Clean the air vents
Vibration or noise is excessive Bolts/nuts are loose Tighten bolts/nuts
Product suddenly stops
Battery pack capacity too low Remove and charge battery pack
Battery too hot Remove battery pack and let it cool down
WWW.SENIXTOOLS.COM 15 - EN
PARTS
No. Part # Description Qty.
22 202196000003 Blower tube 1
EN - 16 WWW.SENIXTOOLS.COM
WARRANTY
LIMITED TWO-YEAR WARRANTY
2-year limited warranty on all Senix X2 series outdoor battery powered equipment and charger. 2-year limited warranty on all
Senix X2 batteries.*
FOR TWO YEARS from the original date of retail purchase this Senix product is warranted against defects in materials or
workmanship on power tools and chargers. Defective product will receive free repair.*
FOR TWO YEARS from the original date of retail purchase this Senix product is warranted against defects in materials or
workmanship on batteries. Defective product will receive free repair.*
This warranty does not cover normal wear of parts and components such as cutting chain, line or blades nor does this
warranty cover product transportation cost for warranty or service.
Warranty is subject to the following conditions:
• Warranty applies to the original purchaser at retail and is not transferrable*
• Warranty Registration at www.senixtools.com
• The tool has not been misused, abused, neglected, altered, modied or repaired by anyone other than an authorized
service center
• Only genuine Senix accessories have been used with or on this product
• The tool has been subjected to normal wear and tear
• The tool has not been used for trade or professional purposes
• The tool has not been used for rental purposes
• This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect
resulting from misuse, abuse (including overloading the product, exposure to water or rain) accidents, neglect or lack of
proper installation and improper maintenance or storage.
To locate your nearest Senix service provider call toll free at 800-261-3981 or email us at [email protected].
Additional Limitations
Any implied warranty granted under state law, including warranties of merchantability or tness for a particular purpose,
are limited to three years from the date of purchase on power tools and chargers and seven years on batteries. The
manufacturer is not responsible for direct, indirect, incidental or consequential damages. Some states and provinces do not
allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental damages,
so the above limitations and exclusions may not apply to you. This warranty gives you specic legal rights, and you may also
have other rights which vary from state to state or province to province.
The YAT USA declines any responsibility in regard to civil liability arising from abusive use or not in conformity with proper
use and maintenance of the machine as described in the operator’s manual.
YAT USA is not responsible for direct, indirect, incidental or consequential damages.
After the purchase, the manufacturer recommends proper maintenance of the machine and to read the operator’s manual
before using the machine.
*Original purchase receipt may be required for proof of purchase
For customer service contact us toll free at 1-800-261-3981 or Senixtools.com.
YAT USA, Inc. 6441 Hendry Rd. Suite A Charlotte, NC. 28269
CON IONES DE LITIO DE 20V MÁX
SOPLADOR DE VENTILADOR
AXIAL INALÁMBRICO
Manual del operador
Modelo: BLAX2-M
BLAX2-M-0
Para el servicio de atención al cliente, llame al 1-800-261-3981 o envíe un email a:
GUARDE ESTE MANUAL PARA FUTURAS CONSULTAS.
INSTRUCCIONES ORIGINALES
TM
ES - 18 WWW.SENIXTOOLS.COM
12
3 4 5 7
6
8
9
1
23
Botón de liberación del tubo del soplador
WWW.SENIXTOOLS.COM 19 - ES
4
6
5
Botón de luz
Control de crucero
Interruptor de encendido/apagado
Mango
ES - 20 WWW.SENIXTOOLS.COM
ÍNDICE
SEGURIDAD Y SÍMBOLOS INTERNACIONALES ...........20
INSTRUCCIONES DE SEGURIDAD ................................21
CONOZCA SU UNIDAD .................................................... 27
ESPECIFICACIONES* ...................................................... 27
ENSAMBLAJE ...................................................................28
OPERACIÓN ..................................................................... 28
MANTENIMIENTO ............................................................30
SOLUCIÓN DE PROBLEMAS ..........................................32
PIEZAS ..............................................................................33
GARANTÍA ........................................................................34
SEGURIDAD Y SÍMBOLOS IN-
TERNACIONALES
Este manual del operador describe la seguridad y los sím-
bolos y pictogramas internacionales que pueden aparecer
en este producto. Lea el manual del operador para obtener
información completa sobre seguridad, montaje, operación
y mantenimiento y reparación.
Precaución / Advertencia.
Para reducir el riesgo de lesiones, el usuario
debe leer y entender el manual de instruc-
ciones.
Use protección para los ojos
Use protección auditiva.
Use protección respiratoria.
No usar bajo la lluvia o en condiciones de
humedad.
Use guantes de protección.
Use calzado robusto no resbaladizo.
No usar bajo la lluvia o en condiciones de
humedad.
Mantenga a todos los transeúntes al menos a
50 pies (15 m) de distancia.
Los objetos lanzados pueden rebotar y causar
lesiones personales o daños a la propiedad.
No deseche los paquetes de baterías en los
ríos ni los sumerja en agua.
No arroje los paquetes de baterías al fuego.
Explotarán y causarán lesiones.
Use y guarde la batería a una temperatura
inferior a 122°F (50 °C).
No desensamble, aplaste o caliente por enci-
ma de los 212°F (100°C). Nunca exponga la
batería a microondas o altas presiones.
Para uso solo en interiores. Utilice el cargador
de batería únicamente en interiores.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54

Senix BLAX2-M Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues