OKIN RF54 Mode d'emploi

RF54
Marque
OKIN
Modèle
RF54
Taper
Mode d'emploi
Issue Department：Bedding Division
Date：
2017-8-15
System Instruction
Author：
Instruction of RF54
Edition：
1.1
Page 1 of 5
1 / 5
Instruction of RF54
Figure 1 button ofremote
1.1 ZG button（button 10 in figure 1）
Click the ZG button, the actuator moves to ZG position, stop when click any button during the
movement;
Press and hold the ZG button for 5s, timer LED of remote flashes, the control box records
current position as ZG position;
When in the process of moving to memory positions, the head and foot actuators move first,
Issue Department：Bedding Division
Date：
2017-8-15
System Instruction
Author：
Instruction of RF54
Edition：
1.1
Page 2 of 5
2 / 5
then the tilt and lumbar actuators move;
1.2 M1 button（button 4 in figure 1）
Click the M1 button, the actuator moves to M1 position, stop when click any button during
the movement;
1.3 M2 button（button 6 in figure 1）
Click the M2 button, the actuator moves to M2 position, stop when click any button during
the movement;
1.4 Head up（button 7 in figure 1）
Press and hold HEAD UP button of remote, head actuator moves out, stop when
released；
1.5 Head down（button 8 in figure 1）
Press and hold HEAD DOWN button of remote, head actuator moves in, stop when released；
1.6 Foot up（button 11 in figure 1）
Pressa and hold FOOT UP button of remote, foot actuator moves out, stop when released;
1.7 foot down（button 12 in figure 1）
Press and hold FOOT DOWN button of remote, foot actuator moves in , stop when released；
When moving to flat position, lumbar actuator and tilt actuator move first, after 500ms, head and
foot actuators start moving;
1.8 Flat（button 9 in figure 1）
Click FLAT button, the bed goes flat, stop when click any button during the process of going
Issue Department：Bedding Division
Date：
2017-8-15
System Instruction
Author：
Instruction of RF54
Edition：
1.1
Page 3 of 5
3 / 5
flat；
1.9 Massage head（button 1 in figure 1）
Click MASSAGE HEAD button, head massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3；
1.10 Massage FOOT（button 3 in figure 1）
Click MASSAGE FOOT button, head massage motor switches massage intensity, massage
intensityswitches among 0-1-2-3；
1.11 Massage ON/OFF（button 2 in figure 1）
Click Massage ON/OFF button, if the massage motors are on, then it turns off massage
motors,if massage motors are off, then it turns on the massage motors;
1.12 Massage Type（button 5 in figure 1）
Click massage type button, to switch the massage mode og massage motors, massage mode
switches among type0type1type2type3type0; this button can only switch the massage
mode, it can not open massage motors；
FCC warning
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are
Issue Department：Bedding Division
Date：
2017-8-15
System Instruction
Author：
Instruction of RF54
Edition：
1.1
Page 4 of 5
4 / 5
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by
doing one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user‘s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC exposure compliance requirement, please follow
operation instruction as documented in this manual.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with ISED exposure compliance requirement, please follow
operation instruction as documented in this manual.
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Les utilisateurs finaux doivent suivre les instructions d'utilisation
spécifiques pour satisfaire la conformité d'exposition RF. Pour maintenir la conformité aux
exigences de conformité d'exposition ISED, veuillez suivre les instructions d'utilisation comme
documenté dans ce manuel.
ISED RSS Warning:
This device complies with Innovation,Science and Economic Development Canada licenceexempt
RSS standard(s). Operation is subject to the following two conditions:
Issue Department：Bedding Division
Date：
2017-8-15
System Instruction
Author：
Instruction of RF54
Edition：
1.1
Page 5 of 5
5 / 5
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radioexempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

OKIN RF54 Mode d'emploi

RF54
Marque
OKIN
Modèle
RF54
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents