Amprobe AM-AC68C Le manuel du propriétaire

AC68C

True RMS AC/DC Clamp Multimeter

Users Manual

• Mode d’emploi

• Bedienungshandbuch

• Manual de Uso

PN 2729051

July 2006

AC68C

AC/DC TRUE RMS

AC68C

True RMS AC/DC Clamp

Multimeter

Users Manual

• Mode d’emploi

• Bedienungshandbuch

• Manual de Uso

English

Limited Warranty and Limitation of Liability

Your Amprobe® product will be free from defects in material and

workmanship for 1 year from the date of purchase. This warranty

does not cover fuses, disposable batteries or damage from

accident, neglect, misuse, alteration, contamination, or abnormal

conditions of operation or handling. Resellers are not authorized

to extend any other warranty on Amprobe®’s behalf. To obtain

service during the warranty period, return the product with proof

of purchase to an authorized Amprobe® Test Tools Service

Center or to a Amprobe® dealer or distributor. See Repair

Section above for details. THIS WARRANTY IS YOUR ONLY

REMEDY. ALL OTHER WARRANTIES - WHETHER EXPRESS,

IMPLIED OR STAUTORY - INCLUDING IMPLIED WARRANTIES

OF FITNESS FOR A PARTICULAR PURPOSE OR

MERCHANTABILITY, ARE HEREBY DISCLAIMED.

MANUFACTURER SHALL NOT BE LIABLE FOR ANY SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR

LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some

states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this

limitation of liability may not apply to you.

1

True RMS AC/DC Clamp Multimeter

Contents

Symbols................................................................................. 1

Introduction........................................................................... 1

Warnings and Precautions..................................................... 2

Unpacking and Inspection ..................................................... 2

Instrument Familiarization (See inside front cover)............... 2

Measuring Procedures........................................................... 3

Specifications ........................................................................ 6

Troubleshooting .................................................................... 8

Battery Replacement.............................................................. 9

Repair .................................................................................... 10

Symbols

W Refer to the manual X Dangerous Voltage

T Double insulated

BT

Battery

F Direct Current J Earth Ground

B Alternating Current R Audible tone

P Complies with EU

directives >Underwriters

Laboratories, Inc.

Introduction

The AC68C is a true rms digital clampmeter that measures both

AC and DC current as well as AC and DC voltage, Resistance,

Frequency, Continuity and Diode Test.

2

Warnings and Precautions

The AC68C Digital Clampmeter conforms to EN61010-2-032,

EN61010-1, CAT III- 600V, class 2 and pollution deg. 2; and

UL3111-1. It is recommended for use with local level power

distribution, appliances, portable equipment, etc., where only

smaller transient overvoltages may occur, and not for primary

supply lines, overhead lines, and cable systems.

• Do not exceed the maximum overload limits per function

(see specifications) nor the limits marked on the

instrument itself. Never apply more than 600 V dc / ac

rms between the test lead and earth ground.

• Inspect the DMM, test leads and accessories before

every use. Do not use any damaged part.

• Never ground yourself when taking measurements. Do

not touch exposed circuit elements or test probe tips.

• Do not operate the instrument in an explosive

atmosphere.

• Exercise extreme caution when: measuring voltage

>20 V // current >10 mA // AC power line with inductive

loads // AC power line during electrical storms //

current, when the fuse blows in a circuit with open

circuit voltage >600 V // servicing CRT equipment.

• Always measure current in series with the load – NEVER

ACROSS a voltage source. Check fuse first. Never

replace a fuse with one of a different rating.

• Remove test leads before opening the case.

Unpacking and Inspection

Your shipping carton should include:

Digital clamp meter 1

Carrying case 1

Test lead set (one black, one red) 1

One 9V battery (installed) 1

Manual 1

If any of the items are damaged or missing, return the complete

package to the place of purchase for an exchange.

Instrument Familiarization (See inside front cover)

Transformer Jaws: Designed to pick up the current flowing

through the conductor.

Jaw Opening Lever: Press lever to open transformer jaws.

Release pressure to close the jaws.

Digital Display: 3-3/4 digit LCD (max. reading 3999), with

decimal point, AC/DC, polarity, unit and low battery (

BT

)

indicators.

Function/Range Selector: Selects the desired function and range.

Changing position turns instrument back on after Auto-OFF.

3

Peak Hold Button: Toggles on and off. Captures the maximum

peak value of a current or voltage surge (motor start-up). “PEAK”

is shown on LCD.

Data Hold Button: Toggles on and off. Holds reading for all

functions and ranges. Always release HOLD before taking a new

measurement. “HOLD” is shown on LCD.

DCA ZERO Button: Push this button to zero the display before

measuring DC current.

Input Terminals: Always connect black test lead (negative) to

black COM input jack and red test lead to red “VΩ” input jack for

voltage, frequency, resistance, continuity, and diode

measurements

Measuring Procedures

General

1. Make sure that the selected function and range are

suitable for the measurement to be taken.

2. If the measured current is higher than the selected range

for a longer period of time, overheating may occur,

compromising the safety and operation of inner circuits.

3. Do not measure currents on high voltage conductors

(> 600 V) to avoid risks of discharge and/or incorrect

readings.

4. When measuring current, make sure that the test leads are

removed from the meter terminals.

5. The most accurate current reading will be obtained by

placing the conductor in the center of the jaws (aligned

with the centering marks on the transformer jaws).

DC Current Measurement

1. Set the function/range selector to the appropriate A F

position (400 or 600 A).

2. Press the DCA ZERO button to make sure that the display

is zero-reading.

3. Open spring-loaded clamp by pressing the lever on left

side of meter.

4. Position clamp around one wire or conductor and release

the clamp lever. Make sure that the clamp is entirely

closed. The clamp must be positioned around only one

conductor. If it is placed around two or more current

carrying conductors, the reading is FALSE.

5. Read the displayed value. The direction of the current

corresponds to the indication of the pointer on the jaw.

Polarity inversion is indicated by a ’-‘ (minus) symbol on

the display.

4

AC Current Measurement

1. Set the function/range selector to the appropriate A B

position (400 or 600 A).

2. Open spring-loaded clamp by pressing the lever on left

side of meter.

3. Position clamp around one wire or conductor and release

the clamp lever. Make sure that the clamp is entirely

closed. The clamp must be positioned around only one

conductor. If it is placed around two or more current

carrying conductors, the reading is FALSE.

4. Read the displayed value.

DC and AC Voltage Measurement

W Warning

The maximum input voltage for DC or AC Volts is 600 Vrms. Do

not attempt to take any voltage measurement that exceeds

600 Vrms to avoid electrical shock hazard or damage to the

instrument.

1. Set the function/range selector to the appropriate V F

(600 V) or V B (400 or 600 V) position.

2. Connect the black test lead to the “COM” terminal and the

red test lead to the “VΩ’’ terminal. Connect probe tips to

the circuit and read the value.

Frequency Measurement

Note: Both ammeter and voltmeter can be used for frequency

measurement. The clamp-on Ammeter detects the frequency of

the current circulating in the cable or bus-bar under test (the

current must be greater than 1 A in the 400 A range and greater

than 15 A in the 600 A range). The Voltmeter detects the

frequency of the voltage applied to the leads.

1. In either set-up (current or voltage measurement), set the

function/range switch to the Hz position.

2. Read the frequency value on the display.

5

Resistance Measurement

W Warning

Before taking any in-circuit resistance measurement, remove

power from the circuit being tested and discharge all

capacitors.

1. Set the function/range selector to the 4 kΩ position.

2. Connect the black lead to the COM terminal and red lead to

the “VΩ” terminal.

3. Connect the test leads to the resistance or circuit to be

measured and read the value on the display.

Continuity Measurement

WWarning

Before taking any in-circuit continuity measurement, remove

power from the circuit being tested and discharge all

capacitors.

1. Set the function/range selector to the R position.

2. Connect the black lead to the COM terminal and red lead to

the “VΩ” terminal.

3. Connect the test leads to the circuit to be tested.

Continuity (resistance ≤40 Ω) is indicated by a continuous

beep tone.

Diode Test

1. Set the function/range selector to the G position.

2. Connect the black lead to the COM terminal and red lead to

the “VΩ” terminal.

3. Connect the red test lead to the anode, and the black test

lead to the cathode of the diode to be tested.

4. Read the forward voltage value on the display (approx.

0.6 V for a silicon diode or 0.4 V for a germanium diode).

An open diode is indicated by “OL”.

5. Reverse test lead connections to the diode to perform a

reverse bias test. “OL” indicates a good diode.

Notes: “OL” for both reverse and forward bias tests indicates an

open diode. A low voltage reading for both bias tests indicates a

shorted diode. If the diode is shunted by a resistor of 1000 ohms

or less, it must be removed from the circuit before taking the

measurement. Bipolar transistor junctions may be tested in the

same manner described above as emitter-base and base-

collector junctions are diode junctions.

Peak Hold Measurement

Proceed as for voltage or current measurement (AC or DC).

Before actually taking the measurement, press the PEAK button.

“PEAK” is shown on the display. After taking a measurement, the

displayed reading is the maximum peak value of a surge in the

voltage or current.

6

Data Hold

Proceed as for voltage or current measurement (AC or DC).

While taking a measurement, press the HOLD button. “HOLD” is

shown on the display and the current meter reading is

maintained, even after disconnecting the test leads from the

circuit or removing the conductor from the clamp. Press HOLD

again to deactivate before taking a new measurement.

Specifications

General Specifications

Display: 3-3/4 Digit LCD, max. reading of 3999. Function and

unit indication.

Overrange indication: “OL” indicated.

Polarity indication: automatic; positive implied; negative

indicated.

Zero adjustment: automatic for all functions and ranges except

DC current (Zero adjustment button).

Ranging: manual function and range selection with rotary

selector switch. Autoranging for frequency measurement.

Special functions: Data Hold, Peak Hold

Operating principle: dual slope integration

Sampling rate: 2 /sec, nominal.

Maximum voltage between any terminal and earth ground: 600 V

Low Battery Indication:

BT

when battery voltage drops below

operating voltage.

Auto Power Off: Approx. 30 minutes after no function change.

Environmental Conditions

Operating temperature: 0 °C to +40 °C, <80 % R.H., non-

condensing

Storage temperature: -10 °C to +60 °C, <70 % R.H., battery

removed.

Power source: Single 9 V battery (NEDA 1604,1EC 6F22)

Battery life: Alkaline 200 hours.

Maximum jaw opening: 40 mm (1.57 inches)

Pollution degree: Level II

Altitude: < 2000 meters

Size (WxLxH): 76x228x39 mm (3”x9”x1.5”)

Weight: 465 gr (incl. battery)

Accessories: Test leads, battery, manual and carrying case.

7

P >

Safety: Meets EN61010-1 Cat III 600V. EN61010-2-03, UL3111-

1, CSA22.2, No 1010-1

EMC: Meets EN55011, EN61000-4-2,4

EMC: This product complies with requirements of the following

European Community Directives: 89/336/EEC (Electromagnetic

Compatibility) and 73/23/EEC (Low Voltage) as amended by

93/68/EEC (CE Marking). However, electrical noise or intense

electromagnetic fields in the vicinity of the equipment may

disturb the measurement circuit. Measuring instruments will also

respond to unwanted signals that may be present within the

measurement circuit. Users should exercise care and take

appropriate precautions to avoid misleading results when making

measurements in the presence of electronic interference.

Electrical Specifications

Accuracy is ± (%reading + nbr digits) at 23 °C ± 5 °C, < 80 %

R.H. The current error is specified within the largest circle that

can be drawn inside the jaw.

DC Current

Range Resolution Accuracy Overload Prot.

400 A 0.1 A ± (2 %rdg + 5 dgt) 800 A

600 A 1 A ± (2 %rdg + 5 dgt) 800 A

AC Current, Trms

Range Resolution Accuracy Overload Freq.

Prot. Response

400 A 0.1 A ± (2 %rdg + 5 dgt) 800 A 40-450 Hz

600 A 1 A ± (2 %rdg + 5 dgt) 800 A 40-450 Hz

Conversion: Ac coupled Trms

Crest Factor (Non-Sinusoidal) (50 – 60 Hz)

1 – 3: ± 0.5 % 3 – 5: ± 3 % 5 – 7: ± 6 %

DC Voltage

Range Resolution Accuracy Input. Overload

Imped. Prot.

600 V 1 V ± (0.75 %rdg + 2 dgt) 1 MΩ 660 Vrms

AC Voltage Trms – Frequency response: 40-450 Hz

Range Resolution Accuracy Input Overload

Imped. Prot.

400 V 0.1 V ± (1.2 %rdg + 10 dgt) 1 MΩ 660 Vrms

600 V 1 V ± (1.2 %rdg + 10 dgt) 1 MΩ 660 Vrms

Conversion: Ac coupled Trms

Crest Factor (Non-Sinusoidal) (50 – 60 Hz)

1 – 3: ± 0.5 % 3 – 5: ± 3 % 5 – 7: ± 6 %

Frequency (Hz) – Autoranging for current and voltage

Range Resolution Accuracy Sensitivity Overload

Prot.

8

4k Hz 1 Hz ± (0.5 %rdg + 5 dgt) 1 V / 5 A 660 Vrms

/800 A

20 kHz* 0.01 Hz ± (0.5 %rdg + 5 dgt) 5 V 660 Vrms

* - Voltage input only

Resistance

Range Resolution Accuracy Open Overload

circ.volts Prot.

4 kΩ 1 Ω± (1 %rdg + 5 dgt) ≤ 0.5 VDC 660 Vrms

Diode Test

Range Resolution Accuracy Open Overload

circ.volts Prot.

G 0.001 V ± (1 %rdg + 2 dgt) 3.0 VDC max 660 Vrms

Max short circuit current: 0.8 mA (typical)

Audible Continuity Test

Range Accuracy Open circ.volts Overload Prot.

40 Ω ≤ 0.5 V 3.0 VDC max 660 Vrms

Max short circuit current: 0.8 mA (typical)

Peak Hold Measurement, AC Voltage (50 Hz – 60 Hz)

Range Resolution Accuracy Input Overload

Imped. Prot.

400 V 0.1 V ± (1.5 %rdg +10 dgt) 1 MΩ 660 Vrms

600 V 1 V ± (1.5 %rdg +10 dgt) 1 MΩ 660 Vrms

Peak Hold Measurement, AC Current (50 Hz – 60 Hz)

Range Resolution Accuracy Overload

Prot.

400 A 0.1 A ± (2 %rdg +10 dgt) 800 A

600 A 1 A ± (2 %rdg +10 dgt) 800 A

Troubleshooting

In case of malfunction during the operation of the meter, the

following steps should be performed in order to isolate the cause

of the problem:

1. Check the battery.

2. Review the operating instructions for possible mistakes in

operating procedure.

3. Check the clamp against a known current source. Use the

voltage function to measure a known voltage (AC and DC).

4. Check the test leads for continuity (voltage and

resistance). Except for the replacement of the battery,

repair of the clamp should be performed only by a Factory

Authorized Service Center or by other qualified instrument

service personnel. Front panel and case can be cleaned

with a mild solution of detergent and water. Apply

sparingly with a soft cloth and let dry completely before

using. Do not use aromatic hydrocarbons or chlorinated

solvents for cleaning.

9

Battery Replacement

XWWARNING

To avoid electrical, shock remove the test leads from both the

meter and the test circuit before accessing the battery.

1. Replace the battery as soon as the low-battery symbol

BT

is displayed.

2. Set the function/range switch to OFF and remove the test

leads.

3. Position the meter face down. Remove the screw and lift

off the back cover.

4. Replace the battery with an equivalent 9 V battery.

5. Reassemble the instrument.

10

Repair

All test tools returned for warranty or non-warranty repair or for

calibration should be accompanied by the following: your name,

company’s name, address, telephone number, and proof of

purchase. Additionally, please include a brief description of the

problem or the service requested and include the test leads with

the meter. Non-warranty repair or replacement charges should

be remitted in the form of a check, a money order, credit card

with expiration date, or a purchase order made payable to

Amprobe® Test Tools.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery

before requesting repair. During the warranty period any

defective test tool can be returned to your Amprobe® Test Tools

distributor for an exchange for the same or like product. Please

check the “Where to Buy” section on www.amprobe.com for a

list of distributors near you. Additionally, in the United States and

Canada In-Warranty repair and replacement units can also be

sent to a Amprobe® Test Tools Service Center (see below for

address).

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be

sent to a Amprobe® Test Tools Service Center. Call Amprobe®

Test Tools or inquire at your point of purchase for current repair

and replacement rates.

In USA In Canada

Amprobe® Test Tools Amprobe® Test Tools

Everett, WA 98203 Mississauga, ON L4Z 1X9

Tel: 888-993-5853 Tel: 905-890-7600

Fax: 425-446-6390 Fax: 905-890-6866

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe®

Test Tools distributor for a nominal charge. Please check the

“Where to Buy” section on www.amprobe.com for a list of

distributors near you.

European Correspondence Address*

Amprobe® Test Tools Europe

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

*(Correspondence only – no repair or replacement available from

this address. European customers please contact your

distributor.)

AC68C

True RMS AC/DC Clamp

Multimeter

Users Manual

• Mode d’emploi

• Bedienungshandbuch

• Manual de Uso

French

Françias

Limites de garantie et de responsabilité

Amprobe® garantit l’absence de vices de matériaux et de

fabrication de ce produit dans des conditions normales

d’utilisation et d’entretien pendant une période d’un an prenant

effet à la date d’achat. Cette garantie ne s’applique pas aux

fusibles, aux piles jetables ni à tout produit mal utilisé, modifié,

contaminé, négligé ou endommagé par accident ou soumis à des

conditions anormales d’utilisation et de manipulation. Les

distributeurs agréés par Amprobe® ne sont pas autorisés à

appliquer une garantie plus étendue au nom de Amprobe®. Pour

bénéficier de la garantie, renvoyez le produit accompagné d’un

justificatif d’achat auprès d’un centre de services agréé par

Amprobe® Test ou du distributeur ou du revendeur Amprobe®.

Voir la section Réparation ci-dessus pour tous les détails. LA

PRESENTE GARANTIE EST LE SEUL ET EXCLUSIF RECOURS

TOUTES AUTRES GARANTIES, EXPLICITES, IMPLICITES OU

STATUTAIRES, NOTAMMENT LE CAS ECHEANT LES

GARANTIES DE QUALITE MARCHANDE OU D’ADAPTATION A

UN OBJECTIF PARTICULIER SONT EXCLUES PAR LES

PRESENTES. LE FABRICANT NE SERA EN AUCUN CAS TENU

RESPONSABLE DE DOMMAGES PARTICULIERS, INDIRECTS,

ACCIDENTELS OU CONSECUTIFS, NI D’AUCUNS DEGATS OU

PERTES DE DONNEES, SUR UNE BASE CONTRACTUELLE,

EXTRA-CONTRACTUELLE OU AUTRE. Etant donné que certains

pays ou états n’admettent pas les limitations d’une condition de

garantie implicite, ou l’exclusion ou la limitation de dégâts

accidentels ou consécutifs, les limitations et les exclusions de

cette garantie ne s’appliquent pas obligatoirement à chaque

acheteur.

1

True RMS AC/DC Clamp Multimeter

Contenu

Symboles utilisés dans ce mode d’emploi................................... 1

Introduction.................................................................................1

Informations de sécurité.............................................................. 2

Désemballage ..............................................................................2

Présentation de l’appareil ............................................................3

Procédures de Mesure................................................................. 3

Spécifications .............................................................................. 6

Dépannage................................................................................... 9

Remplacement de la Pile ............................................................. 9

Réparation ................................................................................. 10

Symboles utilisés dans ce mode d’emploi

W

Se reporter au mode

d’emploi X

Tension

dangereuse

T

Double isolation

BT

Pile

F

Courant continu J Prise de terre

B

Courant alternatif R Signal sonore

P Conforme aux

directives de l’UE > Underwriters

Laboratories,

Inc.

Introduction

L'AC68C est une pince ampèremétrique numérique de mesure

efficace vraie (TRMS) qui mesure le courant c.a. et c.a. ainsi que

la tension c.a. et c.c., la résistance, la fréquence, la continuité et

le contrôle de diode.

2

Informations de sécurité

Le multimètres-pince Modèle AC68C est conformes à la norme

EN61010-1, CAT III 600 V, classe 2 et degré de pollution 2;

UL3111-1. Ils sont recommandés pour les appareils, les

équipements portables et la distribution d’énergie au niveau

local, etc., où seules de petites surtensions transitoires sont

possibles; il n’est pas destiné aux lignes du réseau d’alimentation

électrique principale aux lignes aériennes ou aux systèmes

câblés.

• Ne pas dépasser les limites de surcharge maximum par

fonction (voir les caractéristiques techniques) ou les

limites indiquées sur l’appareil lui-même. Ne jamais

appliquer plus de 600 V c.c./ V c.a. eff. entre le cordon de

test et la prise de terre.

• Inspecter le multimètre numérique, les cordons de test et

les accessoires avant toute utilisation. Ne pas utiliser de

pièce endommagée.

• Ne jamais se relier à la terre en prenant des mesures. Ne

toucher ni aux éléments de circuit exposés ni aux pointes

des sondes de test.

• Ne pas utiliser l’appareil dans une atmosphère explosive.

• Faire preuve d’extrême prudence en : mesurant une tension

>20 V // un courant >10 mA // les lignes d’alimentation

secteur avec charges inductives // les lignes d’alimentation

secteur pendant les orages électriques // un courant alors

que le fusible a sauté dans un circuit avec une tension en

circuit ouvert >600 V // lors d’une intervention sur un

appareil à écran cathodique.

• Toujours mesurer le courant en série avec la charge –

JAMAIS AUX BORNES d’une source de tension. Vérifier

d’abord le fusible. Ne jamais installer un fusible de calibre

différent.

• Retirer les cordons de test avant d’ouvrir le boîtier.

Désemballage

Votre emballage devrait contenir:

Un multimètre-pince..........................................................1

Une sacoche ......................................................................1

Une paire de cordons de test (un noir, un rouge)..............1

Une pile 9 V (dans l’appareil).............................................1

Manuel...............................................................................1

Si une pièce manque ou est endommagée, retournez à votre

point de vente pour un échange.

3

Présentation de l’appareil

1. Pince: Capte le courant qui passe par le conducteur.

2. Levier de la Pince: Poussez ce levier pour ouvrir la pince.

La pince ferme quand la pression est relachée.

3. Affichage Digital: LCD 3-3/4 digits (3999 points), point

décimal , indicateurs CA/CC, de polarité, d’unités et de pile

déchargée (

BT

).

4. Sélecteur de fonctions et de gammes. Un changement de

position rallume également l’appareil après une cupure

automatique.

5. Mémoire de valeurs-crête: Enregistre la valeur-crête du

courant ou de la tension (ex.: mise en route d’un moteur).

“PEAK” est affiché.

6. Maintien de lecture: Maintient la lecture pour toutes

fonctions et gammes. “HOLD” est affiché. Désactivez

HOLD pour prendre de nouvelles mesures.

7. Mise à Zéro pour mesures de courant continu: Pressez ce

bouton avant de prendre une mesure de courant continu.

8. Entrées: Pour les mesures de tension, de résistance, de

continuité, de fréquence et de diodes, connectez toujours

le cordon de mesure noir à l’entrée COM, et le rouge à

l’entrée VΩ.

Procédures de Mesure

Général

1. Assurez-vous que la fonction et la gamme choisies

correspondent à la mesure que vous voulez effectuer.

2. Si le courant mesuré dépasse la gamme choisie durant

une période de temps prolongée, un surchauffement peut

se produire, compromettant la sécurité et le bon

fonctionnement des circuits internes.

3. Ne mesurez pas du courant sur des conducteurs à haute

tension (> 600 V) afin d’éviter des chocs électriques et/ou

des mesure incorrectes.

4. Quand vous mesurez du courant, assurez-vous que les

cordons de mesure sont retirés de l’appareil.

5. La meilleure précision de mesure est obtenue quand le

conducteur de courant est placé au milieu de de la pince

(dans l’alignement des marquages sur la pince).

4

Mesure de Courant Continu

1. Placez le sélecteur sur la position A F désirée (400 ou

600 A).

2. Pressez le bouton de mise-à-zéro et assurez-vous que

l’afficheur est bien bien mis à zéro.

3. Ouvrez la pince en poussant sur le levier.

4. Placez la pince autour du conducteur et fermez la (en

relachant le levier). Assurez-vous que la pince est

complètement fermée et qu’elle ne contient qu’un seul

conducteur. Si elle en contient plusieurs, la mesure est

faussée.

5. Lisez la valeur affichée. La direction du courant

correspond au marquage sur la pince. Une inversion de

polarité est indiquée par un symbole −(moins) sur

l’afficheur.

Mesure de Courant Alternatif

1. Placez le sélecteur sur la position A B désirée (400 ou

600 A).

2. Ouvrez la pince en poussant sur le levier.

3. Placez la pince autour du conducteur et fermez la (en

relachant le levier). Assurez-vous que la pince est

complètement fermée et qu’elle ne contient qu’un seul

conducteur. Si elle en contient plusieurs, la mesure est

faussée.

4. Lisez la valeur affichée.

Mesure de Tension Continue et Alernative

W Avertissement

La valeur d’entrée maximale pour la mesure de tension

continue ou alterntive est de 600Veff. Ne mesurez pas une

tension supérieure afin d’éviter des chocs électriques et/ou

des dommages à l’appareil.

1. Placez le sélecteur sur la fonction et gamme appropriées:

V F (600 V) ou V B(400 ou 600 V).

2. Connectez le cordon noir à l’entrée COM et le rouge à

l’entrée VΩ. Connectez les pointes de touche au circuit (en

parallèle avec la source de tension) et lisez la valeur.

La page charge ...

Amprobe AM-AC68C Le manuel du propriétaire

Ce manuel convient également à

Amprobe AM-AC68C Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents