Cradlepoint W2000 Mode d'emploi

Catégorie
Antennes réseau
Taper
Mode d'emploi
W2000 Series Indoor 5G Wideband Adapter
Professional Installation Guide
Introduction
This document provides a brief overview of the W2000 indoor 5G Wideband adapter, discusses
what's inside the box, and provides basic set up and install instructions.
Disclaimer
Cradlepoint, Inc. (“Cradlepoint”) does not warrant that the hardware will work properly in all
environments or applications, and makes no warranty or representation, either implied or
expressed, with respect to the quality, performance, merchantability, or fitness for a particular
purpose of the W2000 indoor 5G Wideband adapter even when installed in accordance with this
Professional Installation Guide.
This Professional Installation Guide is provided “AS IS,” without any warranty of any kind.
Without limiting the foregoing, to the maximum extent permitted by applicable law Cradlepoint
expressly disclaims all representations, warranties and conditions, whether express, implied,
statutory, or otherwise, with respect to this Professional Installation Guide, including without
limitation any warranty of title, non-infringement, merchantability or fitness for a particular
purpose. While Cradlepoint has made every effort to ensure this Professional Installation Guide
is accurate, Cradlepoint disclaims liability for any inaccuracies or omissions that may have
occurred and shall not be liable for any adverse results caused, in whole or in part, by the
installer’s reliance upon the instructions in this Professional Installation Guide. Information in
this Professional Installation Guide is subject to change without notice and does not represent a
commitment on the part of Cradlepoint. Cradlepoint assumes no responsibility for any
inaccuracies that may be contained in this Professional Installation Guide. Cradlepoint makes no
commitment to update or keep current the information in this Professional Installation Guide and
reserves the right to make improvements to this Professional Installation Guide and/or to the
products described in this Professional Installation Guide, at any time without notice.
If you find information in this Professional Installation Guide that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
Intended Audience
This article is intended for professional networking hardware installers. It provides basic
knowledge and should be used only as a reference guide for installing the W2000 indoor 5G
Wideband adapter. Due to the unique nature of each installation, potential for RF exposure, and
enhanced separation requirements, customers must have a professional install their 5G hardware.
This document is a reference guide and is intended only to provide best practices.
Installer Responsibility
Cradlepoint hereby disclaims any liability for failure of the installer to install the hardware
properly and for any other acts and omissions of the installer. By using this Professional
Installation Guide, you agree to indemnify and hold Cradlepoint harmless from and against any
and all, liabilities, losses, damages, costs and expenses (including without limitation attorneys’
fees and costs) incurred by Cradlepoint arising out of or in connection with any installation work
that is done other than in accordance with the instructions in this Professional Installation Guide.
Limitation of Liability
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL
CRADLEPOINT BE LIABLE TO YOU OR TO ANYONE CLAIMING THROUGH OR
UNDER YOU FOR ANY LOST PROFITS, EQUIPMENT DOWNTIME, OR LOSS OF DATA
OR BUSINESS OPPORTUNITY, OR FOR ANY INDIRECT, SPECIAL, EXEMPLARY,
INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, HOWEVER CAUSED AND
UNDER ANY THEORY OF LIABILITY, ARISING IN ANY WAY IN CONNECTION WITH
YOUR INSTALLATION ACTIVITIES, EVEN IF CRADLEPOINT HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE. SOME JURISDICTIONS (SUCH AS THE
STATE OF NEW JERSEY) DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR
LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL THE AGGREGATE
LIABILITY OF CRADLEPOINT AND/OR ITS AFFILIATES ARISING UNDER OR IN
CONNECTION WITH THE PRODUCT, HOWEVER ARISING, REGARDLESS OF THE
NUMBER OF EVENTS, OCCURRENCES, OR CLAIMS GIVING RISE TO LIABILITY,
EXCEED THE PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT. THE
FOREGOING LIMITATIONS WILL APPLY EVEN IF THE ABOVE STATED REMEDY
FAILS OF ITS ESSENTIAL PURPOSE.
Professional Installer Network
Email our Professional Installer Network for assistance in locating a professional installer in
your service area at <TBD>@cradlepoint.com.
Navigation
Use the following links to quickly navigate through this quick start guide.
Introduction ....................................................................................................................................... 1
Disclaimer ............................................................................................................................................................ 1
Intended Audience ............................................................................................................................................... 2
Installer Responsibility......................................................................................................................................... 2
Limitation of Liability .......................................................................................................................................... 2
Professional Installer Network ............................................................................................................................. 2
W2000 Indoor 5G Wideband Adapter Models................................................................................. 3
Before You Begin .............................................................................................................................. 4
Location Considerations....................................................................................................................................... 4
Ethernet Cable Considerations ............................................................................................................................. 4
SIM Card Setup for Wireless Connectivity .......................................................................................................... 4
Setup .................................................................................................................................................. 5
STEP 1: Check box contents. ............................................................................................................................... 5
STEP 2: Insert an Activated 2FF-Sized SIM. ...................................................................................................... 5
STEP 3: Attach the antennas. ............................................................................................................................... 6
STEP 4: Mount the adapter. ................................................................................................................................. 7
STEP 5: Connect to a power source. .................................................................................................................... 9
STEP 6: Activate the endpoint through NetCloud Manager. ............................................................................... 9
Understanding LEDs ....................................................................................................................... 10
Troubleshooting .............................................................................................................................. 12
Resources ......................................................................................................................................... 12
Help and Support ............................................................................................................................ 12
Terms of Service .............................................................................................................................. 13
Regulatory Requirements ............................................................................................................... 13
W2000 Indoor 5G Wideband Adapter Models
This guide applies to the following products:
CRADLEPOINT W2000-5GA MODEL: S5A010A
CRADLEPOINT W2000-5GB MODEL: S5A103A
Before You Begin
Read the following before setting up your W2000 indoor 5G Wideband adapter.
Location Considerations
The W2000 Indoor 5G Wideband adapter is purpose-built for indoor mounting and should be
installed by a professional. The following includes considerations when identifying a location for
mounting.
This endpoint must be installed at a location where the radiating antennas can be kept
38cm (for USA installations), 45cm (for Canada installations), or 23cm (Australia
installations) in the normal operating condition to meet Radio Frequency (RF) Exposure
requirements. Refer to the Regulatory Requirements section of this document for more
information.
Ensure that the mounting surface is flat and clear of any obstructions or objects that may
interfere with the antennas, signal reception, or cables.
Position the endpoint for optimal cellular and Wi-Fi signal reception.
Avoid mounting in direct sunlight or in locations where it may be exposed to the weather.
Ensure plenty of airflow for ventilation.
Mount in locations compliant with the Safety, Regulatory, and Warranty guide, included
in the product shipping box. Refer to the Regulatory Requirements section of this guide
for quick reference.
IMPORTANT: The W2000 indoor 5G Wideband adapter requires increased separation
distances in relation to other networking hardware. Therefore, Cradlepoint requires that all 5G
adapters be installed by a professional. For assistance with installation or in locating a
professional installer, contact Cradlepoint Sales and Support.
Ethernet Cable Considerations
Cradlepoint recommends shielded, twisted-pair (S/FTP) Ethernet network cabling and
connectors (Cat6a/Cat7a) for optimal wired network performance.
SIM Card Setup for Wireless Connectivity
A wireless broadband data plan must be added to your Cradlepoint W2000 for wireless
broadband connectivity. Network providers, such as AT&T, Verizon, and Telstra, must provision
a SIM to provide wireless broadband data plans compatible for use with the Cradlepoint W2000
indoor 5G Wideband adapter endpoints. Contact your network provider for further details.
Setup
The following instructions are intended for network hardware installers. Read through the
following to set up your W2000 indoor 5G Wideband adapter or use the Verify mobile
installation app.
STEP 1: Check box contents.
The W2000 Indoor 5G Branch Adapter and required accessories are shipped in two boxes.
Box 1 - Hardware Only:
o [1] W2000 indoor 5G Wideband adapter hardware
Box 2 - Accessories Kit:
o [1] 90 W PoE Injector
o [4] Cellular antennas
o [1] Indoor mounting kit
o [1] Screw pack
o [1] Safety, Regulatory, and Warranty guide
o [1] Quick Start reference sheet
STEP 2: Insert an Activated 2FF-Sized SIM.
1. Unscrew and remove the modem door on the
W2000 endpoint.
2. Insert an activated 2FF-sized SIM into the slot
marked SIM1, with metal contacts up and
notch in. It will click into place. To remove,
depress again if necessary.
3. Use the SIM2 slot for a secondary/backup, as
needed.
4. Replace the modem cover and secure with the
modem door screw.
STEP 3: Attach the antennas.
Attach the four (4) included cellular antennas to the connectors marked MAIN0 and DIV0/1/2. If
desired, attach an active GPS antenna (not included) to the SMA connector marked GPS.
Hold the antenna straight and twist the base of the antenna to connect, folding the joint if
needed.
Antennas are jointed for optimal signal positioning.
o NOTE: Ensure that the antennas are not near metal or other RF reflective
surfaces.
STEP 4: Mount the adapter.
The W2000 includes a set of mounting plates that allow the adapter to be mounted in multiple
locations.
REMINDER: This endpoint must be installed at a location where the radiating antennas can be
kept 38cm (for USA installations), 45cm (for Canada installations), or 23cm (Australia
installations) in the normal operating condition to meet Radio Frequency (RF) Exposure
requirements. Refer to the Regulatory Requirements section of this document for more
information.
For basic mounting best practices, refer to the following:
WALL & CEILING
Use the included mounting
template (Fig.1) to mark the
desired mounting location on the
wall or ceiling with a marker or
pen. There will be an arrow to
indicate which direction is up.
Pre-drill holes for the mounting
screws.
Attach the wall & ceiling
mounting bracket (Fig. 2) to the
wall or ceiling in the marked
location, securing with M3
screws and anchors.
o NOTE: Do not use power
tools on the adapter or
mounting plates. Use
hand-held screw drivers to attach screws only.
Align the W2000 keyholes on the back of the endpoint to the mounting pegs on the
bracket.
Slide the endpoint down until it clicks into place.
Figure 3. Drop Ceiling
Mounting Bracket
Figure 2. Wall & Ceiling Mounting
Bracket
Figure 1. Mounting Template
o NOTE: To remove the endpoint from the bracket, depress the latch on the left-
hand side of the bracket and pull the endpoint up and off of the bracket pegs.
Once the W2000 and brackets are securely connected, attach the M3 security screw to
ensure the endpoint is immobile.
DROP CEILING
The ceiling mount assembly works for standard 9/16ths and
15/16ths drop ceilings. It is not designed for recessed drop
ceilings. Do not use power tools on the adapter or mounting
plates. Use hand-held screw drivers to attach screws only.
Join the drop ceiling (Fig. 3) and wall & ceiling
mounting (Fig. 2) brackets into the ceiling mount
assembly.
o Align the drop ceiling bracket to the flat back
portion of the mounting bracket.
NOTE: There is only one position that
will allow the two pieces to fit together.
o Use the included M3 screws to secure the two
bracket pieces together.
Route the Ethernet cable(s) through the middle of the
ceiling mount assembly and route through the cable
clip. The clip will align the cables with the WAN and
LAN ports on the side of the W2000.
Attach the ceiling mount assembly to the desired location on the drop ceiling frame.
o Lift up the ceiling panels to isolate the frame.
o Align the frame to the of the ceiling mount assembly so that the mounting clips
are on either side of the frame.
o Press the bracket against the frame and twist the bracket slightly to the right until
the clips click onto the frame.
Align the W2000 keyholes on the back to the mounting pegs on the bracket. Slide the
endpoint along the pegs until it clicks into place.
Secure with the M3 security screw.
JUNCTION BOX
The mounting plate is designed to work with standard-sized junction boxes. Use the included
template to fit the mounting plate to the junction box to attach the W2000. Refer to the Wall &
Ceiling section in this document for more information.
STEP 5: Connect to a power source.
Connect an Ethernet cable to the PoE 2.5G LAN1 port and plug the other end into the
included 802.11bt (90W) PoE-injector, or a 802.11bt enabled port on an attached router
or switch (not included).
Ensure the PoE injector, router, or switch port is powered on.
o The power LEDs will begin to light up.
STEP 6: Activate the endpoint through NetCloud Manager.
Activate your endpoint through NetCloud Manager (NCM). Your endpoint is packaged with
NetCloud services and activation requires that you log into your NetCloud account. Refer
to Getting Started with NetCloud Manager for more information.
Understanding LEDs
Refer to the following for information about the LED indicators on the Cradlepoint W2000
indoor 5G Wideband adapter.
NOTE: The W2000 LEDs are only visible when the endpoint is powered on. They are located
along the top edge of the adapter, above the SIM slot cover.
Status
Indicator Behavior
POWER The Cradlepoint W2000 and W2005 must be powered using an approved 54
V DC power source.
No Light = Not receiving power. Check the power switch
and source connection.
Green = Powered ON.
Yellow = Attention. Log into NCM and use the Remote
Connect menu to access the router’s NCOS to manage any
alert.
o NOTE: Upon initial installation, the light will be
yellow until the endpoint is registered in NetCloud
Manager (NCM).
SIGNAL
STRENGTH
LED bars indicate the modem’s signal strength.
4 Solid Bars = Strongest signal
1 Blinking Bar = Weakest signal (A blinking bar indicates
half of a bar)
4 Blinking Bars = SIM door is not installed, modem is off
MODEM
Indicates information about the modem.
No Light = Modem not connected.
o NOTE: You will not be able to see the icon when the
modem is not connected.
Solid Green = Modem has established an active WAN
connection.
Blinking Green = Modem is connecting.
Solid Yellow = Modem is not active.
Blinking Yellow = Data connection error. No modem
connection possible.
Blinking Red = Modem is in the process of resetting.
o NOTE: Blinking Red with Signal Strength LEDs =
SIM door is not installed, modem is off.
Wi-Fi
BROADCAST
Indicates activity on the Wi-Fi broadcast for both 2.4 and 5 GHz bands.
No Light = Wi-Fi is not operating.
Blue = Wi-Fi is on and operating normally
LAN
ACTIVITY
Indicates an active LAN connection.
NOTE: Only one LAN connection will be active at a time.
No Light = LAN is not connected or is not currently active.
Flashing Green = Active LAN connection.
OTHER Additional LED Indications
The white Cradlepoint logo on the top face of the endpoint lights up when the
endpoint is connected to a registered NCM account.
Troubleshooting
If the endpoint takes longer than 5 minutes to connect to the Internet, you may need to log into
the local UI of the endpoint to make configuration changes or start the troubleshooting process.
You must be physically co-located with the endpoint in order to do this. Refer to How to
Troubleshoot Connection Issues for additional information.
Once the endpoint connects to the Internet, it should then connect to your NetCloud Manager
account and start its configuration download.
Resources
W2000 Webpage
W2000 Data Sheet
Help and Support
Contact Us
Cradlepoint Customer Connect Community
Cradlepoint Support Services
Terms of Service
Cradlepoint Terms of Service & License Agreement
Privacy Policy
GDPR Privacy Policy
Regulatory Requirements
To comply with FCC regulations limiting both maximum RF output power and human exposure
to RF radiation, the maximum cellular antenna gain must not exceed as below:
Antenna Net Gain (dBi) Frequency Range
2.5 700-960 MHz
2.2 1428-1600 MHz
4.3 1700-2700 MHz
4.6 3300-3700 MHz
6.1 5150-5925 MHz
Except when transmit operation in Band 30 is not disabled (see “FCC LTE Band 30 Notice for
installers in the USA section in the online user manual at www.cradlepoint.com).
Professional installation instructions
1. Installation personnel: This product is designed for specific application and needs to be
installed by a qualified personal who has RF and related rule knowledge. The general
user shall not attempt to install or change the setting.
2. Installation location: The product shall be installed at a location where the radiating
antenna can be kept 38cm (FOR FCC)/45cm (FOR IC) from nearby person in normal
operation condition to meet regulatory RF exposure requirement.
3. External antenna: Use only the antennas which have been approved by the applicant. The
non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting
power which may lead to the violation of FCC/ISED limit and is prohibited.
4. Installation procedure: Please refer to user’s manual for the detail.
5. Warning: Please carefully select the installation position and make sure that the final
output power does not exceed the limit set force in relevant rules. The violation of the
rule could lead to serious federal penalty.
Instructions d'installation professionnelle
1. Installation: Ce produit est destine a un usage specifique et doit etre installe par un
personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant. L'installation
et les reglages ne doivent pas etre modifies par l'utilisateur final.
2. Emplacement d'installation: En usage normal, afin de respecter les exigences
reglementaires concernant l'exposition aux radiofrequences, ce produit doit etre installe
de facon a respecter une distance de 38cm(FOR FCC)/45cm(FOR IC)entre l'antenne
emettrice et les personnes.
3. Antenn externe: Utiliser uniiquement les antennes approuvees par le fabricant.
L'utilisation d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non
essentiel depassant les niveaux limites definis par FCC/ISED, ce qui est interdit.
4. Procedure d'installation: Consulter le manuel d'utilisation.
5. Avertissement: Choisir avec soin la position d'installation et s'assurer que la puissance de
sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de
serieuses penalites federales.
INDUSTRY CANADA RADIATION EXPOSURE STATEMENT
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 45cm
between the radiator & your body.
NOTE IMPORTANTE (Pour l’utilisation de dispositifs mobiles): Déclaration d’exposition
aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 45
cm de distance entre la source de rayonnement et votre corps.
Déclaration d’Industrie Canada
(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis (pour les
dispositifs utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e.
spécifiée, selon le cas;
(iii) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de modèle de
l’antenne et les pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la
p.i.r.e. applicable au masque d’élévation, énoncée à la section 6.2.2.3, doivent être clairement
indiqués.
Le présent émetteur radio [IC: 6921A-S5A103A] a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-
dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et
dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont
strictement interdits pour l'exploitation de l'émetteur.
For CRADLEPOINT W2000-5GB MODEL S5A103A
Manufacturer Model
Antenna Type Max Gain (dBi) Impedance (Ω)
Cradlepoint, Inc. NA Dipole (External)
WWAN:
700-960 MHz: 1.42
1428-1600 MHz: 0.88
1700-2700 MHz: 2.69
3300-3700 MHz: 4.13
5150-5925 MHz: 4.29
NA
For more information about the Safety, Regulatory, and Warranty guide for the W2000 Indoor
5G Wideband Adapter, refer to the inbox insert packaged with your product.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Cradlepoint W2000 Mode d'emploi

Catégorie
Antennes réseau
Taper
Mode d'emploi

dans d''autres langues