iON SnapCam Guide de démarrage rapide

Taper
Guide de démarrage rapide

Quick Start Guide
EN-2
1. Introduction
SnapCam is a HD wearable camera. It allows users to take and
share photos and videos on social media.
2. Key Features
z Ultra Slim and Light-weight
z HD Video (720p @ 30fps)
z 8mp Photos
z Auto rotate.
z Upload and Share Photos and Videos using built-in Wi-Fi
z Magnetic Clip included to wear on clothes, bags, hats etc.
EN-3
3. Function
1. Camera LED (Red) Indicate the cameras reaction
2. Wi-Fi LED (Blue) Indicate Wi-Fi status
3. Battery LED (Green)
Indicate the camera battery
status
4. Lens Wide angle lens
5. Power Button
Turn on and off the camera
Turn on and off the Wi-Fi
Reset the camera
6. Magnet
For attaching your SnapCam to
clothing etc.
7. Microphone
EN-4
8. MicroSD Card Slot For MicroSD card
9. Micro USB Port
Connection for charging and
mass storage
10. Touch Panel
activate video, photo and live
streaming.
11. Silicon Bumper
Protect the camera and
decoration
12. Back Clip Mount
To clip to clothing and
accessories to make SnapCam
wearable.
4. First Time Use
4.1 Charging your SnapCam
EN-5
Charge the built-in battery before starting to use your SnapCam. When
the SnapCam is off, the charging time from empty to full is approximately
1.5 hours.
The LED will turn solid GREEN once the SnapCam is fully charged.
4.2 Inserting a MicroSD Memory Card
You must insert a MicroSD Card (required, not included) before using the
SnapCam. The SnapCam supports MicroSD Card from 2GB to 32GB
Class 6 or higher is recommended.
Note:
There is only one direction to insert the MicroSD Card into the slot. Do
not force the MicroSD Card into the slot as this may damage both the
EN-6
scanner and the MicroSD Card.
The MicroSD Card must be formatted before first time use.
4.3 Setting Date & Time
When the SnapCam is used for the first time, or it has been restored to
default settings, it is necessary to set the SnapCam’s clock to ensure the
captured photo and video files are saved with correct date and time
information.
To set-up the SnapCam’s clock:
1. Insert a formatted MicroSD Card into the SnapCam.
2. Connect the SnapCam to a PC as mass storage device (please
refer to Section 5.9).
3. Open the MicroSD file folder, create a file in any format (eg. txt
file) and name it with the format “set-YYYYMMDD-HHMM”, YYYY,
MM, DD, HH, MM represent the year, month and day, hour,
minute of existing time. (eg : set-20150618-1100.txt)
4. Disconnect the SnapCam from the PC, and tap once on
SnapCam touch panel, the SnapCam will scan the file and write it
to system clock.
5. Using the SnapCam
Please ensure you are running the latest firmware to get the best from
EN-7
your SnapCam, visit www.ioncamera.com for firmware updates.
5.1 Wearing your SnapCam
This method is suitable for wearing your SnapCam on a jacket or
relatively thick clothes.
EN-8
Note: Wear your SnapCam vertically, otherwise, the SnapCam may slip
and produce a tilted view.
Disclaimer: Please do not put the magnet clip too close to magnetic card
strips (credit/debit cards) or smartphones to avoid malfunctions.
EN-9

Note: Please remove the sticker on the surface of your SnapCam before
use.
5.2 Power On your SnapCam.
Press the Power On button for 3-4 seconds, the SnapCam will
automatically search for a Wi-Fi network.
EN-10
5.3 Take a Single Photo
Simply tap the touch panel of your SnapCam to take a photo. The red
LED will flash once to indicate the photo was taken. You may also take a
single photo using iON SnapCam App by clicking “Take Photo” icon.
EN-11
5.4 Use Time Lapse to take Photos
1. Set your SnapCam to Time Lapse Photo function using the iON
SnapCam App and smart device.
2. Simply click “Start Time Lapse Photo” on the iON SnapCam App,
then your SnapCam will start to take photos at the set time intervals.
3. You may cancel the Time Lapse Photo function using the iON
SnapCam App
EN-12
5.5 Video Recording
1. Simply tap the touch panel of your SnapCam twice to start video
recording. The red LED will stay solid for the duration of recording.
You may also start video recording through iON SnapCam App by
clicking “Start Video” icon.
2. Tap the touch panel of your SnapCam twice to stop video recording,
or click “Stop Video” icon on iON SnapCam App.
Note: Please note changing video or photo resolution will decrease
battery life.
EN-13
5.6 Short Video Recording
1. Set the duration of Short Video Recording using iON SnapCam
App and a smart device. (Default is 15 seconds)
2. Simply touch and hold the touch panel of your SnapCam to start
short video recording. You may also start/stop short video recording
through iON SnapCam App by clicking “Start Short Video” icon.
EN-14
5.7 Live Streaming
Your SnapCam is capable of live streaming.
1. Make sure your SnapCam is connected to a Wi-Fi network
2. Open the iON SnapCam App and select your SnapCam in the
Device Page.
3. Swipe the touch panel of your SnapCam from left to right to start
live streaming.
4. To stop live streaming, swipe the touch panel of your SnapCam
from right to left.
EN-15
5.8 Connecting your SnapCam to a smart device.
You may control your SnapCam using the iON SnapCam App and a
smart device.
1. Open the iON SnapCam App and select Device Icon to enter to
the Device Page.
2. Click “Device\Add New”. Automatic device search will begin.
3. Select your SnapCam from the list of available devices.
EN-16
Note : Minimum operating system requirement for iON SnapCam App:
Android 4.3, iOS 4.0
5.9 Connecting your SnapCam to PC
The SnapCam can be connected to computer as mass storage device
(MS Mode) and transfer the photos and video files for storage, if it is not
under recording. If the SnapCam is recording when connected to a PC, it
will not enter to the mass storage mode but will begin charging.
EN-17
6. Specifications
Lens Wide angle lens
Water Resistance IPX4
Still Image
resolution
8MP (Default), 2MP
Video Resolution 720p 30fps , WVGA : 848 x 480
Video Format MPEG4 (H.264) .MP4 File
Photo Format JPG
Memory Slot MicroSD card
Support System
Windows XP, Vista, 7, and 8 ;
Mac OS X 10.6 or later
Microphone Built-in
Battery Life 2 hours continuous recording
Dimension (L x H x
W)
40 x 40 x 12.5 mm
Weight 32g
Operation
Temperature
-10°C - 45°C
Storage
Temperature
-20°C - 70°C
EN-18
7. Troubleshooting
Problem Cause Solution
Unable to record
videos or photos
1. MicroSD card is
not inserted.
2. Memory is full.
Camera
malfunction.
1. Insert a MicroSD
card. Supports
2GB – 32GB
class 6 or higher.
2. Replace a
memory card
with space
available for
content.
3. Reset the
camera.
Cannot find
removable disk
after connecting the
camera to the
computer
Connection failure.
1. Check all cable
connections.
2. Restart the
computer if
necessary.
Blurry images
The lens of camera
is dirty
Clean the lens with
soft and dry cloth
EN-19
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
EN-20
Specific Absorption Rate (SAR) information:
This equipment meets the government's requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety margin designed to
assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6
W/kg averaged over one gram of tissue. Device types: FCC ID: NW71045 has also
been tested against this SAR limit. The highest SAR value reported under this
standard during product certification for use when properly worn on the body is
1.288 W/kg or head is 1.478 W/kg. This device was tested for typical body-worn
operations with the back of the handset kept 0 cm from the body or head. The use
of accessories that do not satisfy these requirements may not comply with FCC RF
exposure requirements, and should be avoided.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182

iON SnapCam Guide de démarrage rapide

Taper
Guide de démarrage rapide