Roland CUBE-80X Manuel utilisateur

Español Italiano Français Deutsch EnglishPortuguêsNederlands

Owner’s Manual

Bedienungsanleitung

Guide d’utilisation

Manuale dell'utente

Manual del usuario

Manual do proprietário

Gebruikershandleiding

I

202

any form without the written permission of ROLAND CORPORATION.

cube-80x.book Page 1 Tuesday, November 25, 2008 3:33 PM

2

cube-80x.book Page 2 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

Owner’s Manual

201b

Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY

INSTRUCTIONS”, “USING THE UNIT SAFELY”

(p. 2) and “IMPORTANT NOTES” (p. 4). These

sections provide important information concerning the proper operation of the unit.

Additionally, in order to feel assured that you have gained a good grasp of every feature

provided by your new unit, Owner’s Manual should be read in its entirety. The manual

should be saved and kept on hand as a convenient reference.

Control Panel

INPUT Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

JC CLEAN Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SELECT Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TUNER Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LEAD Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SOLO Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

EQUALIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PRESENCE Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

EFX (Effects) Knob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

DELAY/LOOPER Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

REVERB Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

POWER Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Contents

Main Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using the SOLO Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using the LOOPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Using the Tuner Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Sample Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

I

202

any form without the written permission of ROLAND CORPORATION.

cube-80x.book Page 1 Tuesday, November 25, 2008 3:33 PM

2

USING THE UNIT SAFELY

001-50

• Connect mains plug of this model to a mains

socket outlet with a protective earthing

connection.

..........................................................................................................

002a

• Do not open or perform any internal modifications

on the unit.

..........................................................................................................

003

• Do not attempt to repair the unit, or replace parts

within it (except when this manual provides

specific instructions directing you to do so). Refer

all servicing to your retailer, the nearest Roland

Service Center, or an authorized Roland

distributor, as listed on the “Information” page.

..........................................................................................................

004

• Never install the unit in any of the following

locations.

• Subject to temperature extremes (e.g., direct

sunlight in an enclosed vehicle, near a heating

duct, on top of heat-generating equipment); or

are

• Damp (e.g., baths, washrooms, on wet floors);

or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Humid; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and

shakiness.

..........................................................................................................

007

• Make sure you always have the unit placed so it is

level and sure to remain stable. Never place it on

stands that could wobble, or on inclined surfaces.

..........................................................................................................

008a

• The unit should be connected to a power supply

only of the type described in the operating

instructions, or as marked on the rear side of unit.

...........................................................................................................

009

• Do not excessively twist or bend the power cord,

nor place heavy objects on it. Doing so can

damage the cord, producing severed elements

and short circuits. Damaged cords are fire and

shock hazards!

...........................................................................................................

010

• This unit, either alone or in combination with an

amplifier and headphones or speakers, may be

capable of producing sound levels that could

cause permanent hearing loss. Do not operate for

a long period of time at a high volume level, or at

a

level that is uncomfortable. If you experience

any hearing loss or ringing in the ears, you should

immediately stop using the unit, and consult an

audiologist.

...........................................................................................................

011

• Do not allow any objects (e.g., flammable material,

coins, pins); or liquids of any kind (water, soft

drinks, etc.) to penetrate the unit.

...........................................................................................................

013

• In households with small children, an adult should

provide supervision until the child is capable of

following all the rules essential for the safe

operation of the unit.

...........................................................................................................

014

• Protect the unit from strong impact.

(Do not drop it!)

...........................................................................................................

Used for instructions intended to alert the

user to the risk of death or severe injury

should the unit be used improperly.

About WARNING and CAUTION Notices

About the Symbols

ALWAYS OBSERVE THE FOLLOWING

cube-80x.book Page 2 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

3

USING THE UNIT SAFELY

012a

• Immediately turn the power off, remove the

power cord from the outlet, and request servicing

by your retailer, the nearest Roland Service

Center, or an authorized Roland distributor, as

listed on the “Information” page when:

• The power-supply cord or the plug has been

damaged; or

• If smoke or unusual odor occurs

• Objects have fallen into, or liquid has been

spilled onto the unit; or

• The unit has been exposed to rain (or

otherwise has become wet); or

• The unit does not appear to operate normally

or exhibits a marked change in performance.

..........................................................................................................

Add

• A small amount of heat will radiate from the unit

during normal operation. Do not use the unit in

an area with less than the air space shown below.

..........................................................................................................

015

• Do not force the unit’s power-supply cord to share

an outlet with an unreasonable number of other

devices. Be especially careful when using

extension cords—the total power used by all

devices you have connected to the extension

cord’s outlet must never exceed the power rating

(watts/amperes) for the extension cord. Excessive

loads can cause the insulation on the cord to heat

up and eventually melt through.

..........................................................................................................

016

• Before using the unit in a foreign country, consult

with your retailer, the nearest Roland Service

Center, or an authorized Roland distributor, as

listed on the “Information” page.

..........................................................................................................

026

• Do not put anything that contains water (e.g.,

flower vases) on this unit. Also, avoid the use of

insecticides, perfumes, alcohol, nail polish, spray

cans, etc., near the unit. Swiftly wipe away any

liquid that spills on the unit using a dry, soft cloth.

..........................................................................................................

101a

• The unit should be located so that its location or

position does not interfere with its proper

ventilation.

...........................................................................................................

102a

• Always grasp only the plug on the power-supply

cord when plugging into, or unplugging from an

outlet.

...........................................................................................................

103a

• At regular intervals, you should unplug the power

plug and clean it by using a dry cloth to wipe all

dust and other accumulations away from its

prongs. Also, disconnect the power plug from the

power outlet whenever the unit is to remain

unused for an extended period of time. Any

accumulation of dust between the power plug

and the power outlet can result in poor insulation

and lead to fire.

...........................................................................................................

104

• Try to prevent cords and cables from becoming

entangled. Also, all cords and cables should be

placed so they are out of the reach of children.

...........................................................................................................

106

• Never climb on top of, nor place heavy objects on

the unit.

...........................................................................................................

107a

• Never handle the power cord or its plug with wet

hands when plugging into, or unplugging from,

an outlet.

...........................................................................................................

108a

• Before moving the unit, disconnect the power

plug from the outlet, and pull out all cords from

external devices.

...........................................................................................................

109a

• Before cleaning the unit, turn off the power and

unplug the power cord from the outlet.

...........................................................................................................

110a

• Whenever you suspect the possibility of lightning

in your area, pull the plug on the power cord out

of the outlet.

...........................................................................................................

121

• Do not remove the speaker grille and speaker by

any means. Speaker not user replaceable. Shock

hazardous voltages and currents are present

inside the enclosure.

...........................................................................................................

20 cm (8 inch)

or greater

20 cm (8 inch)

or greater

30 cm (12 inch)

or greater

15 cm (6 inch)

or greater

5 cm (2 inch)

or greater

cube-80x.book Page 3 Tuesday, November 25, 2008 3:33 PM

4

IMPORTANT NOTES

Power Supply

301

• Do not connect this unit to same electrical outlet that is being

used by an electrical appliance that is controlled by an inverter

(such as a refrigerator, washing machine, microwave oven, or air

conditioner), or that contains a motor. Depending on the way in

which the electrical appliance is used, power supply noise may

cause this unit to malfunction or may produce audible noise. If it

is not practical to use a separate electrical outlet, connect

a

power supply noise filter between this unit and the electrical

outlet.

307

• Before connecting this unit to other devices, turn off the power

to all units. This will help prevent malfunctions and/or damage to

speakers or other devices.

308

• Although the LEDs are switched off when the POWER switch is

switched off, this does not mean that the unit has been

completely disconnected from the source of power. If you need

to turn off the power completely, first turn off the POWER switch,

then unplug the power cord from the power outlet. For this

reason, the outlet into which you choose to connect the power

cord’s plug should be one that is within easy reach and readily

accessible.

Placement

351

• Using the unit near power amplifiers (or other equipment

containing large power transformers) may induce hum. To

alleviate the problem, change the orientation of this unit; or

move it farther away from the source of interference.

352a

•This device may interfere with radio and television reception. Do

not use this device in the vicinity of such receivers.

352b

• Noise may be produced if wireless communications devices, such

as cell phones, are operated in the vicinity of this unit. Such noise

could occur when receiving or initiating a call, or while

conversing. Should you experience such problems, you should

relocate such wireless devices so they are at a greater distance

from this unit, or switch them off.

354b

• Do not expose the unit to direct sunlight, place it near devices

that radiate heat, leave it inside an enclosed vehicle, or otherwise

subject it to temperature extremes. Also, do not allow lighting

devices that normally are used while their light source is very

close to the unit (such as a piano light), or powerful spotlights to

shine upon the same area of the unit for extended periods of

time. Excessive heat can deform or discolor the unit.

355b

• When moved from one location to another where the

temperature and/or humidity is very different, water droplets

(condensation) may form inside the unit. Damage or malfunction

may result if you attempt to use the unit in this condition.

Therefore, before using the unit, you must allow it to stand for

several hours, until the condensation has completely

evaporated.

356

• Do not allow rubber, vinyl, or similar materials to remain on the

unit for long periods of time. Such objects can discolor or

otherwise harmfully affect the finish.

359

• Do not paste stickers, decals, or the like to this instrument.

Peeling such matter off the instrument may damage the exterior

finish.

360

• Depending on the material and temperature of the surface on

which you place the unit, its rubber feet may discolor or mar the

surface.

You can place a piece of felt or cloth under the rubber feet to

prevent this from happening. If you do so, please make sure that

the unit will not slip or move accidentally.

Maintenance

401a

• For everyday cleaning wipe the unit with a soft, dry cloth or one

that has been slightly dampened with water. To remove

stubborn dirt, use a cloth impregnated with a mild, non-abrasive

detergent. Afterwards, be sure to wipe the unit thoroughly with

a

soft, dry cloth.

402

• Never use benzine, thinners, alcohol or solvents of any kind,

to

avoid the possibility of discoloration and/or deformation.

452Kai

• Please be aware that unit settings or the contents of the solo

function stored in memory may be lost when the unit is sent for

servicing. Important data should always be written down on

paper. Roland assumes no liability with respect to recovery of

any lost data.

Additional Precautions

551Kai

• Please be aware that unit settings or the contents of the solo

function stored in memory can be irretrievably lost as a result of

a malfunction or the improper operation of the unit. To protect

yourself against the risk of losing important data, we recommend

that you periodically write down on paper any important data

you have stored in the unit’s memory.

552Kai

• Roland Corporation assumes no liability with respect to recovery

of any lost unit settings or contents of the solo function stored in

memory.

553

• Use a reasonable amount of care when using the unit’s buttons,

sliders, or other controls; and when using its jacks and

connectors. Rough handling can lead to malfunctions.

556

• When connecting / disconnecting all cables, grasp the connector

itself—never pull on the cable. This way you will avoid causing

shorts, or damage to the cable’s internal elements.

557

• A small amount of heat will radiate from the unit during normal

operation.

558a

• To avoid disturbing your neighbors, try to keep the unit’s volume

at reasonable levels. You may prefer to use headphones, so you

do not need to be concerned about those around you (especially

when it is late at night).

559a

• When you need to transport the unit, package it in the box

(including padding) that it came in, if possible. Otherwise, you

will need to use equivalent packaging materials.

562

• Some connection cables contain resistors. Do not use cables that

incorporate resistors for connecting to this unit. The use of such

cables can cause the sound level to be extremely low, or

impossible to hear. For information on cable specifications,

contact the manufacturer of the cable.

Add

• Do not insert hands, fingers, etc, into the openings in the unit’s

rear panel. In particular, if the unit is to used in households with

small children, always provide adult supervision to ensure that

children keep their hands and feet out of these openings.

cube-80x.book Page 4 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

5

Main Features

● A high-performance guitar amp equipped with a 30-cm (12-inch) speaker and delivering 80 watts of output

● Switchable between two-channels: JC CLEAN and LEAD

Switchable using a footswitch pedal (optional BOSS FS-6, FS-5U, or FS-5L).

● Ten types of COSM amplifiers (p. 6, p. 7)

A total of ten COSM amp types are built in, including a clean amp for the JC CLEAN channel and acoustic, crunch, high-gain, and the

original Dyna Amp for the LEAD channel.

Dyna Amp lets you achieve unprecedented tonal change and new expressiveness by varying your picking dynamics.

COSM (Composite Object Sound Modeling) is proprietary Roland modeling technology, which analyzes the way in which sound is

affected by elements such as electronic circuitry, structure, and materials, and combines these elements to reconstruct the desired

sound.

● SOLO function (p. 9, p. 16)

This lets you save and call up panel settings for tones you create with the LEAD channel, including amp type, gain, equalizer, and

effects. You can also manipulate these using a footswitch pedal (the optional BOSS FS-6, FS-5U, or FS-5L), letting you put them to use

in live performances.

● LOOPER function (p. 9, p. 17)

This lets you record, play back, and overdub a phrase you play to create your own loop phrase, enabling you to enjoy playing along

with the recorded loop phrase.

You can also manipulate this using a footswitch pedal (the optional BOSS FS-6, FS-5U, or FS-5L).

* The maximum recording time is approximately 40 seconds.

● Tuner function (p. 6, p. 19)

An easy-to-operate tuner is built in. This even supports flat tuning and seven-string guitars.

Chromatic tuning is possible, too.

● Independently operable delay and reverb (p. 9)

The unit is equipped with a DELAY knob and a REVERB knob. These let you control delay and reverb independently.

● Delay time adjustable through TAP input

You can also enter a short delay (30 to 90 ms) by giving the TAP switch a long press.

● Spring reverb modeling

Modeling technology replicates a spring reverb with realistic fidelity.

● Four types of easy-to-operate effects (p. 8)

Four types of effects — chorus, flanger, phaser, and tremolo — are built in, allowing easy operation with a single control.

● RECORDING OUT jack (p. 15)

The unit features a RECORDING OUT jack for connecting recording equipment. You can also use this as a headphone jack.

● AUX IN jack (p. 15)

You can use this to connect and play along with an MP3 or CD player.

cube-80x.book Page 5 Tuesday, November 25, 2008 3:33 PM

6

Panel Descriptions

Connect your guitar here.

This models the Roland JC-120.

This is a sound that readily extends up

to the treble range. This amp is ideal

for creating sounds in combination

with a multi-effects device.

BRIGHT Switch

This makes the mid and high ranges more brilliant, for

a

crisper sound.

VOLUME Knob

This adjusts the volume level of the JC CLEAN channel.

As

an original function on this unit, this can produce

a

powerful crunch at volume levels near the maximum.

This switches between the JC CLEAN and LEAD channels.

The indicator shows you which channel is selected.

You can also switch on the solo function by using this in

combination with the SOLO switch. For more information, refer

to

“Using the SOLO Function” (p. 16).

Switching channels can also be accomplished using a footswitch

pedal (optional BOSS FS-5U, FS-5L, or FS-6).

You use this when tuning the guitar.

Turning this on makes the switch light

in

red and enables tuning.

For information on how to use the tuner,

refer to

“Using the Tuner Function” (p. 19).

Control Panel

INPUT Jack

JC CLEAN Channel

SELECT Switch

TUNER Switch

cube-80x.book Page 6 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

7

Panel Descriptions

You can select from nine COSM amp types.

* The product names mentioned in this document are trademarks or

registered trademarks of their respective owners, and are not related to

Roland Corporation. In this manual, these names are used because it is

the most practical way of describing the sounds that are simulated

using COSM technology.

GAIN Knob

This adjusts the distortion level for the LEAD channel.

VOLUME Knob

This adjusts the volume level for the LEAD channel.

LEAD Channel

Type Description

ACOUSTIC SIM

This is an original amp type that includes an

acoustic simulator.

It transforms the sounds from your electric

guitar into a clear, refined acoustic-guitar

sound.

Using this type together with a single-coil

pickup in the front position produces

optimal sound quality.

If you’re using humbucker pickups, turn

down the equalizer’s BASS and MIDDLE

controls slightly.

BLACK PANEL

This is modeled on the classic Fender Twin

Reverb amplifier.

It’s used in a wide range of musical styles,

from country to blues, jazz, and rock.

It features rich lows and a bright high end.

DLX COMBO

This is modeled on the Fender Deluxe

Reverb amplifier.

This amp finds use in a full range of genres,

including surf music, blues, country, jazz,

soul, and hard rock.

It features clear, clean tones and sparkling

overdrive at high volumes.

BRIT COMBO

This is modeled on the Vox AC-30TB.

This is the rock amplifier that created the

Liverpool sound of the 1960s.

It can produce a broad range of sounds,

from clean to overdrive.

TWEED

This is modeled on the vintage Fender

Tweed Bassman 4x10” Combo.

It produces a clear mid to upper range with

a fat low end, and its unique crunch tones

with persistent distortion have earned it

a

loyal following among blues and rock

guitarists.

CLASSIC

STACK

This is modeled on the features of

a

Marshall JMP 1987.

Used extensively in hard rock in the 1970s,

this is truly the perfect amp for the “top

rock” guitar sound.

METAL STACK

This is modeled on the Peavey EVH 5150.

This is a high-gain amp, so you can get

heavy distortion and sustain even at low

volumes.

R-FIER STACK

This super high-gain amp is modeled on

the Mesa/Boogie Rectifier.

This is a super high-gain amp. It’s capable of

producing slash metal, grunge, and a wide

range of other lead sounds.

DYNA AMP

This is an original amp type that lets you

obtain unprecedented tonal changes

according to your picking dynamics.

Soft picking produces a transparent clean

amp sound, whereas hard picking yields

a deeply distorted high-gain amp sound.

Once the sound is distorted, the tone then

changes according to the force used in

picking, greatly expanding your range of

expression.

* Setting the GAIN knob at the optimal position

provides maximum effectiveness. Start with

the GAIN knob centered. Then adjust the

GAIN knob so that soft picking yields a clean

tone and hard picking produces heavy

distortion.

Type Description

cube-80x.book Page 7 Tuesday, November 25, 2008 3:33 PM

8

Panel Descriptions

This lets you save the panel settings

for sounds you create with the LEAD

channel (such as amp type, gain,

equalizer, and various effects) and

call them up later.

On this unit, this function is called

“SOLO.”

The SOLO function is handy in situations like these:

• When you’re using the LEAD channel and you want to switch

the amp type and effect at the same time

• When you’re using the LEAD channel and you want to switch

the equalizer settings and volume level at the same time

* Settings for the JC CLEAN channel can’t be stored in memory.

SOLO Switch

This saves panel settings and calls up it.

VOLUME (SOLO) Knob

This adjusts the volume level for the called-up settings.

* For information on how to use the SOLO function, refer to “Using the

SOLO Function” (p. 16).

* When the LEAD channel Type switch is set to BLACK PANEL, DLX

COMBO, or TWEED, setting BASS, MIDDLE and TREBLE all to 0 (zero)

stops all sound.

This gives the midrange and high end a more lustrous contour.

This is effective when you want to make the sound more airy and

open.

You can adjust the intensity of four types of

effects—chorus, flanger, phaser, and

tremolo—by adjusting the positioning of this

knob.

The indicator lights up when this is on, and

goes out when it’s off. You can also switch

this on and off using an optional footswitch pedal.

*The scale indications for CHORUS, FLANGER, PHASER, and TREMOLO on

the panel are just a general guide. Be sure to check the actual sound as

you adjust the effect.

SOLO Function

EQUALIZER

Knob Description

BASS Knob

This adjusts the sound level of the low-

frequency range.

MIDDLE Knob

This adjusts the sound level of the

middle-frequency range.

TREBLE Knob

This adjusts the sound level of the high-

frequency range.

PRESENCE Knob

EFX (Effects) Knob

Knob Position Description

CHORUS

This adds a slightly detuned sound to

the original sound, giving the sound

greater breadth and fullness.

FLANGER

This creates a flanging effect that

creates a sort of spinning sensation

with the sound.

PHASER

This adds a phase-shifted signal to the

original sound, giving the sound

a

swirling sensation.

TREMOLO

This effect produces cyclical changes in

the volume level.

cube-80x.book Page 8 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

9

Panel Descriptions

You can switch to either of two delay

types or the LOOPER function by

positioning this knob.

When the knob is at WARM or CLEAR,

this functions as a delay, and you can

adjust the volume level of the delay by

adjusting the knob’s position.

The indicator lights up when delay is on and goes out when it’s

off. You can also switch this on and off using an optional

footswitch pedal.

When the knob is positioned at LOOPER, you can use it to adjust

the volume level of playback using the LOOPER function.

This indicator lights up when the LOOPER function is on. The

indicator flashes when a footswitch pedal is used to switch off

(mute) LOOPER.

* The scale indications for WARM, CLEAR, and LOOPER are just a general

guide. Be sure to check the actual sound as you adjust the effect.

* When the knob is positioned at LOOPER, no delay effect is applied. To

use the LOOPER and delay simultaneously, refer to

“Using the LOOPER

Function and Delay at the Same Time” (p. 18).

TAP Switch

When the knob is positioned at WARM or CLEAR, you can

use this to adjust the delay time.

When the knob is positioned at LOOPER, this switch

controls recording, playback, and overdubbing.

You can switch between use of two types of

reverb by changing the position of the knob.

You can adjust the intensity of the effect by

varying the knob position.

The indicator lights up when reverb is on and

goes out when the effect is off. You can also

switch reverb on and off using an optional

footswitch pedal.

DELAY/LOOPER Knob

Knob Position Function Description

WARM

Delay

This is a feedback delay with

a warm analog-delay feel.

Turn the knob clockwise to

increase the effect sound.

CLEAR

This is a delay with one to

two repetitions.

Turn the knob clockwise to

increase the effect sound.

LOOPER Looper

This enables the loop-play

mode.

You can vary the volume

level for playback by

adjusting the position of the

knob. For more information,

refer to

“Using the LOOPER”

(p. 17).

Knob

Position

Function Operation

WARM,

CLEAR

Adjusts the

delay time

Delay time of 90 ms or more

Pressing the switch twice sets

a

delay time equal to the

interval between presses. You

can set a time of up to 2,000 ms

when the knob is at WARM or

up to 1,000 ms when the knob

is at CLEAR.

Delay time of 90 to 30 ms

Holding down the TAP switch

for one second or longer

changes the delay time in a

stepwise fashion from 30 to 90

ms, according to the number of

seconds you hold the switch

depressed (four stages: 30 ms,

50 ms, 70 ms, and 90 ms).

LOOPER

Starts and

stops Looper

recording

and playback

Refer to “Using the LOOPER

Function and Delay at the Same

Time” (p. 18).

REVERB Knob

Knob Position Description

SPRING

This is modeled on spring reverb.

It produces the distinctive

reverberations of a spring. Turning the

knob clockwise makes the effect

progressively more intense.

PLATE

This is a plate reverb.

This reverb features high-end sustain.

Turning the knob clockwise makes the

effect progressively more intense.

cube-80x.book Page 9 Tuesday, November 25, 2008 3:33 PM

10

Panel Descriptions

s

Turns the power on and off.

941

* Once the connections have been completed (p. 11), turn on power to

your various devices in the order specified. By turning on devices in the

wrong order, you risk causing malfunction and/or damage to speakers

and other devices.

1. Make sure that all volume controls on this

unit and connected devices are set to 0.

2. Turn on all the devices connected to this

unit’s INPUT jack and AUX IN jack.

3. Turn on this unit.

943

* Always make sure to have the volume level turned down before

switching on power. Even with the volume all the way down, you

may still hear some sound when the power is switched on, but this

is normal, and does not indicate a malfunction.

942

* This unit is equipped with a protection circuit. A brief interval (a

few seconds) after power up is required before the unit will operate

normally.

4. Adjust the volume levels for the devices.

5. Before switching off the power, lower the

volume on each of the devices in your

system, and then turn off the devices in the

reverse of the order followed when switching

them on.

945

* If you need to turn off the power completely, first turn off the POWER

switch, then unplug the power cord from the power outlet. Refer to

“Power Supply” (p. 4).

POWER Switch

cube-80x.book Page 10 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

11

Panel Descriptions

921

* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any

connections.

Either momentary or latch type footswitch pedals can be used with this unit.

However, be sure to connect only a momentary-type footswitch such as the BOSS FS-5U to the TAP/REC/PLAY/DUB jack. A latch-type

footswitch pedal may fail to operate correctly.

* The footswitch pedal is available separately.

* The BOSS FS-6 can operate as either a momentary or latch-type pedal switch.

Momentary type: This type remains on (or off) while depressed and switches off (or on) when released. BOSS FS-5U, etc.

Latch type: This type switches on or off each time it is depressed. BOSS FS-5L, etc.

* This unit is equipped with a TRS-type FOOT SW jack that accepts plugs of the configuration shown in the figure. To connect

a footswitch pedal, use a TRS-compatible cable such as the optionally available PCS-31.

Rear Panel

FOOT SW Jacks

FOOT SW TYPE Switch

PCS-31

DELAY/LOOPER MUTE

TAP/REC/PLAY/DUB

REVERB EFX SOLO CH SELECT

Headphones

Mixer, etc.

External Speaker

Speaker Cable

MP3/CD Player, etc.

BOSS FS-6, etc.

Foot Switches

1

4

7

8

2 3

5

6

Recorder, etc.

INPUT

TIP

RING

cube-80x.book Page 11 Tuesday, November 25, 2008 3:33 PM

12

Panel Descriptions

Connection and Settings When Using an FS-5L or Latch-type Footswitch Pedal

When you’re using the FS-6 or FS-5L, you can determine whether the footswitch pedal is on or off by checking its indicator light.

Jack Jack Jack

Function

TIP: TAP/REC/PLAY/DUB

For DELAY: Adjusts the delay time

For LOOPER: LOOPER operation (p. 17)

TIP: EFX

Switches EFX on and off

TIP: SELECT

Switches between the JC

CLEAN and LEAD channels

RING: DELAY/LOOPER MUTE

For DELAY: Switches DELAY on and off

For LOOPER: Mutes LOOPER

RING: REVERB

Switches REVERB on and off

RING: SOLO

Calls up the SOLO function

When

connecting

the FS-5L

When

connecting

the FS-6

CUBE-80X

Rear Panel

DELAY/LOOPER MUTE

TAP/REC/PLAY/DUB

PCS-31

Red

(RING)

White

(TIP)

Polarity switch

REVERB

SOLO

EFX

SELECT

PCS-31

Red

(RING)

White

(TIP)

Polarity switch

CUBE-80X

Rear Panel

BA

Red

(RING)

White

(TIP)

PCS-31

DELAY/LOOPER MUTE TAP/REC/PLAY/DUB

Set the switches as shown as bellow.

REVERB

SOLO

EFX

SELECT

BA

PCS-31

Red

(RING)

White

(TIP)

Set the switches as shown as bellow.

cube-80x.book Page 12 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

13

Panel Descriptions

Important Notes When Using a Latch-type Footswitch Pedal

Normally, the on/off state of the footswitch pedal takes precedence over the control panel for switching EFX, delay, or reverb on

and off.

However, the on or off states stored in memory using the SOLO function take precedence when saved SOLO-function panel

settings are called up. Such cases may result in conflicting indicator displays on the control panel and the footswitch pedal, but this

is not a malfunction.

To make the indicator displays match up

Depress the footswitch pedal whose indicator display is different.

Make it match the indicator display on the control panel.

To make the on/off state of the footswitch pedal take priority at all times

On this unit, you can use either of the following settings to control operation when the panel settings for EFX, delay, and

reverb are called up using the SOLO function.

• Make the on/off state of the footswitch pedal always take priority

• Make the on/off state saved using the SOLO function take priority (default)

1. How to make the on/off state of the footswitch pedal always take priority

Hold down the TAP and SELECT switches at the same time and switch on the power.

2. How to make the on/off state saved using the SOLO function take priority

Hold down the TAP and TUNER switches at the same time and switch on the power.

* The changed setting remains in memory after the power is switched off.

cube-80x.book Page 13 Tuesday, November 25, 2008 3:33 PM

14

Panel Descriptions

Connection and Settings When Using an FS-5U or Momentary-type Footswitch Pedal

Jack Jack Jack

Function

TIP: TAP/REC/PLAY/DUB

For DELAY: Adjusts the delay time

For LOOPER: LOOPER operation (p. 17)

TIP: EFX

Switches EFX on and off

TIP: SELECT

Switches between the JC

CLEAN and LEAD channels

RING: DELAY/LOOPER MUTE

For DELAY: Switches DELAY on and off

For LOOPER: Mutes LOOPER

RING: REVERB

Switches REVERB on and off

RING: SOLO

Calls up the SOLO function

When

connecting

the FS-5U

When

connecting

the FS-6

CUBE-80X

Rear Panel

DELAY/LOOPER MUTE

REVERB

SOLO

TAP/REC/PLAY/DUB

EFX

SELECT

Polarity switch

PCS-31

Red

(RING)

White

(TIP)

CUBE-80X

Rear Panel

BA

DELAY/LOOPER MUTE

REVERB

SOLO

TAP/REC/PLAY/DUB

EFX

SELECT

PCS-31

Red

(RING)

White

(TIP)

Set the switches as shown bellow.

cube-80x.book Page 14 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

15

Panel Descriptions

This is for connecting an external speaker.

When one is connected, sound is played both from the external

speaker and from the unit’s built-in speaker.

Add

* When connecting to an external speaker, make sure the speaker

conforms to the following specifications.

Impedance: 8 ohms or less

Allowable power input: 80 watts or greater

Add

* No sound is output from this unit’s speaker or any external speaker

when the RECORDING OUT/PHONES jack is in use.

Add

* Only use speaker cable to connect the speaker. Do not use any shielded

cable designed for use with guitars.

This functions either as an output jack for recording or as

a

phones jack.

* When a plug is connectedto this jack, no sound is played from either the

unit or any connected external speaker. This is handy at night or in

other situations when you want to avoid high-volume sound from the

speakers.

When using as an output jack for recording

Use a monaural 1/4” phone plug to connect a recorder or

other recording device.

This features COSM speaker modeling, enabling

production of impressive guitar sound.

Adjust the output level using the VOLUME knobs for the JC

CLEAN and LEAD channels and the SOLO function.

When using as a headphones jack

Connect headphones.

This features COSM speaker modeling, enabling

production of impressive guitar sound.

Adjust the headphones volume using the VOLUME knobs

for the JC CLEAN and LEAD channels and the SOLO

function.

This is for connecting a PA system, recorder, or other external

equipment.

This features COSM speaker modeling, enabling production of

impressive guitar-amp sound.

You use this when you want to use the unit in combination with

an external PA system or when you want to line-record

a

performance while listening to the sound from the unit’s built-

in speaker.

Adjust the output level using the VOLUME knobs for the JC

CLEAN and LEAD channels and the SOLO function.

* The sound input to the AUX IN jack is NOT output.

This lets you connect a CD player, digital audio player, electronic

instrument, or other such device and play it at the same time as

the guitar.

This unit is equipped with a stereo mini AUX IN jack. Use a cable

(sold separately) that’s appropriate for the device you’re

connecting.

926a

* When connection cables with resistors are used, the volume level of

equipment connected to the AUX IN jack may be low. If this happens,

use connection cables that do not contain resistors.

* Use the connected device to adjust the volume level.

* Output is monaural.

Connecting the Power Cord

1. Make sure that the POWER switch is off.

2. Connect the power cord to an AC outlet.

EXT SPEAKER Jack

RECORDING OUT/PHONES Jack

LINE OUT Jack

AUX IN Jack

Power Cord

cube-80x.book Page 15 Tuesday, November 25, 2008 3:33 PM

16

Using the SOLO Function

You can save and call up the panel settings (those enclosed by

the line in the figure) for sounds you create with the LEAD

channel. On this unit, this function is called “SOLO.”

By default, “Loud Metal” (p. 20) sample settings are saved in the

SOLO function.

* The VOLUME setting for the LEAD channel is not saved.

* The LOOPER settings and the recorded phrase are not saved.

1. Create a sound with the LEAD channel.

2. Set the SOLO volume at 0 (zero).

If the SOLO volume is set

high, the sound may be

unexpectedly loud when the

panel settings are saved.

Before saving, lower the

volume to 0.

3. Press and hold the SOLO switch on the panel

until the indicator starts to flash

(approximately 2 seconds or longer).

When the panel settings are

saved, the indicator

changes to a steadily

lighted state.

* Never switch off the power

while the indicator is flashing.

4. Adjust the volume for the SOLO function.

* Saved panel settings remain in memory even after the power is

turned off.

1. While at the JC CLEAN or LEAD channel, press

the SOLO switch on the panel.

The SOLO indicator lights up and the panel settings stored

in memory are called up.

* When no panel settings have been saved, or when you’re using the unit

for the first time, the product’s factory-default settings (

“Loud Metal” (p.

20) sample settings) are called up.

1. Press the SOLO switch on the panel to call up

the saved settings.

2. Turn the panel knob for the item you want to

change, and modify the setting.

* The SOLO indicator goes out briefly when the position of the

turned knob coincides with the position stored in memory.

3. Pressing the SOLO switch on the panel until

the indicator starts to flash (approximately 2

seconds or longer) saves the changes to the

settings.

* Never switch off the power while the indicator is flashing.

* Once the new settings have been saved, the previous settings in

effect before the changes cannot be called up again.

* To quit without saving the changes, press the SOLO switch or the

SELECT switch.

You can switch channels using the SELECT switch and the SOLO

switch.

* When a momentary-type footswitch pedal is connected, it also

performs the same operation.

Saving the Panel Settings

Calling Up Panel Settings

Changing or Checking Saved Panel

Settings

Switching the SOLO Function and the

LEAD and JC CLEAN Channels

SELECT

switch

SOLO

switch

SOLO switch

SELECT switch

Returning to the Factory-default Settings

Hold down the TAP switch and the SOLO switch at the same

time and switch on the power.

The SOLO indicator flashes and the settings saved with the

SOLO function are returned to their factory defaults.

cube-80x.book Page 16 Tuesday, November 25, 2008 3:33 PM

Español Italiano Français Deutsch EnglishPortuguêsNederlands

17

Using the LOOPER

This lets you record a phrase you play, and play it back any

number of times. You can also use it to overdub a recorded

phrase.

On this unit, this feature is called the “LOOPER.”

You can also operate the LOOPER function using an optionally

available footswitch pedal.

* The recorded phrase is deleted when the unit is turned off.

* Unauthorized recording, distribution, sale, lending, public performance,

broadcasting, or the like, in whole or in part, of a work (musical

composition, video, broadcast, public performance, or the like) whose

copyright is held by a third party is prohibited by law.

* Never use this unit for any purpose that may infringe on a copyright

held by a third party. Roland assumes no responsibility for any

infringement of third-party copyright arising through your use of this

unit.

1. Set the DELAY/LOOPER knob at LOOPER.

Set the knob at the

maximum setting. With

the knob at the

maximum, the phrase will

be played back at the

same volume as when it

was recorded.

2. Press the TAP switch or depress the TAP/REC/

PLAY/DUB footswitch.

When you press the TAP

switch, it begins flashing in

red and the unit enters

recording standby.

If instead you depress the TAP/

REC/ PLAY/DUB footswitch, the

TAP switch lights in red, and

recording starts immediately.

i

3. Start playing the guitar.

If the unit is in recording standby, the TAP switch lights up

and recording starts.

4. To end recording, press the TAP switch or

depress the TAP/REC/PLAY/DUB footswitch

pedal.

The TAP switch lights in green and the recorded

performance is played back.

5. Pressing either the TAP switch or the TAP/

REC/PLAY/DUB footswitch twice in rapid

succession stops playback.

The TAP switch flashes green.

* You can also stop this by turning the DELAY/LOOPER knob to a position

other than LOOPER.

* The maximum recording time is approximately 40 seconds. When the

maximum recording time is reached, recording automatically stops and

playback starts.

1. While the TAP switch is flashing green, press

the TAP switch or depress the TAP/REC/PLAY/

DUB footswitch pedal.

The TAP switch lights in green and loop playback starts

from the beginning of the phrase.

2. Adjust the volume for the phrase.

You can adjust the volume level of phrase playback by

adjusting the position of the DELAY/LOOPER knob.

3. Pressing the TAP switch twice in rapid

succession stops playback.

The TAP switch flashes green.

Recording a Phrase

Flashes red

Lights red

Playing Back the Recorded Phrase

cube-80x.book Page 17 Tuesday, November 25, 2008 3:33 PM

18

Using the LOOPER

1. Press the TAP switch or depress the TAP/REC/

PLAY/DUB footswitch pedal to play back the

phrase.

The TAP switch lights in green and loop playback of the

phrase starts.

2. Press the TAP switch or depress the TAP/REC/

PLAY/DUB footswitch pedal a once time.

The TAP switch lights in orange and overdubbing starts.

3. To end recording, press the TAP switch or

depress the TAP/REC/PLAY/DUB footswitch

pedal.

The TAP switch lights in green and loop playback of the

recorded performance starts.

4. Pressing the TAP switch twice in rapid

succession stops playback.

The TAP switch flashes green.

* Phrase muting can be carried out only when a footswitch pedal is

connected. Muting cannot be accomplished via the panel.

1. During phrase playback, depress the DELAY/

LOOPER MUTE footswitch pedal.

The playback sound is muted. The DELAY/LOOPER

indicator flashes while muting is in effect.

2. To end muting, depress the DELAY/LOOPER

MUTE footswitch pedal again.

* Recording, deleting and overdubbing can be accomplished even

while muting is in effect.

1. While phrase playback is stopped (and the

TAP switch is flashing green), press and hold

the TAP switch or the TAP/REC/PLAY/DUB

footswitch pedal for approximately 2

seconds or longer.

The TAP switch flashes red and the phrase is deleted.

* Sound may be produced while the delete operation is in progress,

but this doesn’t indicate a malfunction. If you mute the unit before

performing the deletion, the deletion can be carried out silently.

* The deleted phrase cannot be recovered.

Through use together with the SOLO function, you can also use

the LOOPER function and delay at the same time.

Although delay normally cannot be used when the DELAY/

LOOPER knob is set at the LOOPER position, you can use delay by

using the SOLO function to save panel settings that call for delay

to be applied, then activating SOLO while you’re using the

LOOPER function, thereby enabling the delay.

* Switching the delay on or off or changing the delay time is not possible.

Overdubbing the Phrase

Muting the Phrase

Deleting the Phrase

Using the LOOPER Function and Delay

at the Same Time

cube-80x.book Page 18 Tuesday, November 25, 2008 3:33 PM

La page est en cours de chargement...

Roland CUBE-80X Manuel utilisateur

Roland CUBE-80X Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents