Electrohome ELEEAAC470 Manuel utilisateur

Catégorie
Réveils
Taper
Manuel utilisateur
electrohome.com
Thank you for your purchase of this Electrohome product. Please read this
instruction manual carefully before using product to ensure proper use.
Keep this manual in a safe place for future reference.
USER MANUAL
USB Charging Alarm Clock Radio
EAAC470 / EAAC470W
V1.07
AM
AM/FM
FM
PM
DIMMER
PRESETS
SNOOZE/SLEEP
- 2 -
NEED
HELP?
DO NOT RETURN THIS
PRODUCT TO THE STORE
Please contact an
ELECTROHOME®
customer support
representative rst regarding any additional information on
product features, specications or assistance with setup.
Please contact us via one of the methods below:
For more product information visit
www.electrohome.com
Support:
www.electrohome.com/support
Online live web chat:
www.electrohome.com
- 3 -
WARNINGS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
To reduce the risk of re or electric shock, do not expose this appliance to rain or
moisture.
CAUTION
Use of controls or adjustments or performance of procedures other than those specied
may result in hazardous radiation exposure.
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICABLE PARTS INSIDE, REFER TO QUALIFIED USER PERSONNEL.
The lightning ash with arrowhead symbol, within an equilateral traingle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sucient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
TO PREVENT ELECTRIC SHOCK; DO NOT USE THIS PLUG WITH AN EXTENSION CORD RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURES. TO
PREVENT FIRE OR SHOCK HAZARD; DO NOT INSTALL THIS PRODUCT IN A CONFINED SPACE SUCH AS A
BOOK CASE OR SIMILAR UNIT.
CAUTION: RETAIN THIS MANUAL FOR FUTURE REFERENCE
1. Read these instructions.
2. Keep these instructions.
3. Read all warnings.
4. Follow all instructions.
5. Do not use this product near water.
6. WARNING: Please refer to the information on exterior bottom enclosure for electrical and safety
information before installing or operating the apparatus.
- 4 -
IMPORTANT SAFETY INFORMATION
7.
Clean only with a dry cloth
.
8. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
10. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
11. Protect the power cord from being walked on or pinched particularily at plugs, convenience
receptacles, and the point where they exit from the apparatus.
12. Only use attachments/accessories specied by the manufacturer.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. Apparatus shall not be exposed to dripping or splashing, and that not objects lled with
liquids, such as vases, shall be placed on the apparatus.
16. The batteries shall not be exposed to excessive heat such as sunshine, re or the like.
17. The MAINS plug is used as the disconnect device, which shall remain readily operable.
18. The MAINS plug of apparatus should not be obstructed and should be easily accessed during
intended use.
19. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
20. WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or
moisture.
21. There should be a minimum distance of 5 cm around the apparatus for sucient ventilation.
22. The ventilation should not be impeded by covering the ventilation openings with items such as
newspaper, table-cloths, curtains etc.
23. No naked ame sources such as lighted candles should be placed on the apparatus.
24. Please use the apparatus in moderate climates.
25. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold
with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
- 5 -
IMPORTANT SAFETY INFORMATION
26. Unwind and straighten the power cord before use.
27. Damage Requiring Service
Unplug the power cord and refer servicing to qualied service professional under the
following conditions:
A. If liquid has been spilled on or into the product.
B. If the product has been exposed to rain, water, or other liquids.
C. If the product does not operate normally by following the operating instructions, adjust only
those controls that are covered by the operating instructions. Improper adjustment of other
controls may result in damage and will often require extensive work by a qualied technician
to restore the product to its normal operation.
D. If the product has been dropped or damaged in any way.
E. When the product exhibits a distinct change in performance. This may indicate a need
for service.
28. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltages or other hazards. Refer all servicing to a qualied service professional.
29. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts
specied by the manufacturer, or have the same characteristics as the original parts. Unauthorized
substitutions may result in re, electric shock, or other hazards.
30. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
FCC statement on regulation
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
- 6 -
IMPORTANT SAFETY INFORMATION
TABLE OF CONTENTS
Any changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
Consult the dealer or an experienced radio TV technician for help.
This class[B] digital apparatus complies with Canadian ICES-003.
This marking indicates that this product should not be disposed with other household
wastes throughout North America. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmental safe recycling.
!
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does not close securely,
stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate
medical attention.
- 7 -
Need Help? .....................................................................................................................2
Warnings ........................................................................................................................ 3
Important Safety Information ........................................................................................ 4
What’s Included ..............................................................................................................8
Product Information .......................................................................................................8
Operating Instructions ...................................................................................................12
Connecting Power .......................................................................................12
Battery Backup ...........................................................................................12
Installing the battery ..................................................................................13
Daylight Saving Time (DST) / Summer Time ................................................13
Setting the Date & Time ..............................................................................14
Setting Alarm 1 & Alarm 2 ..........................................................................15
Alarm Duration ...........................................................................................17
Snooze Function .........................................................................................17
Sleep Timer ................................................................................................. 17
Adjusting LED Brightness ............................................................................18
Listening to the Radio .................................................................................18
To Set / Recall the Radio Presets .................................................................18
USB Charging Function ...............................................................................19
Troubleshooting ............................................................................................................20
Care and Maintenance ...................................................................................................20
Specications ................................................................................................................21
Electrohome Warranty ...................................................................................................22
TABLE OF CONTENTS
- 8 -
WHAT’S INCLUDED
FRONT - LED SCREEN
1
LED dot appears, indicating AM Band is selected
2
LED dot appears, indicating FM Band is selected
3
Alarm 1 - LED dot appears, when Alarm 1 is set
4
Displays the hour
5
Displays the minutes
6
LED dot appears, indicating time is set to PM
7
LED dot appears, to indicate LED Time Display is set to OFF
8
Volume Setting
9
Alarm 2 - LED dot appears, when Alarm 2 is set
PRODUCT INFORMATION
USB Charging Alarm Clock Radio
Quick Start Guide
Power Adapter
Instructional Manual
1 x 3V, CR2032 Flat Lithium battery
1
4
2
3
5
6
7
8
9
PRODUCT INFORMATION
VOL
- 9 -
PRODUCT INFORMATION
1
Increases Volume
2
Turns Power ON/OFF /AM/FM
Band Selector
3
Decreases Volume
1
Power Input
2
Charges USB devices
1
2
3
FRONT BUTTONS
AM/F
M
1 2
REAR PANEL
- 10 -
PRODUCT INFORMATION
1
Set Radio Presets
2
Set ALARM 1
3
Set ALARM 2
4
SNOOZE / SLEEP / LED BRIGHTNESS / TIME ZONE
5
Set TIME / Y-M-D / 24h-12h Clock ; View Temperature
6
View D-M-Y / Tune-Scan Radio (BACK)
7
Set DST / Tune-Scan Radio (FORWARD) / Select °C OR °F
TOP BUTTONS
PRODUCT INFORMATION
DIMMER
PRESETS
SNOOZE/SLEEP
1 2 3 4 5 6 7
- 11 -
BOTTOM
PRODUCT INFORMATION
1
Battery compartment for 1 x 3V, CR2032 Flat Lithium battery
2
FM Antenna
3
Indoor Temperature Sensor
1
2
3
- 12 -
OPERATING INSTRUCTIONS
CONNECTING POWER
The USB Charging Alarm Clock Radio is equipped with an "AUTO TIME SET" feature.
When power is connected, the clock display will ash '2' which is TIME ZONE 2
(Eastern time) and the default TIME ZONE setting. The correct time will be displayed,
unless you are in another time zone.
To select TIME ZONE 2 (Eastern time) as your default time zone:
Press ONCE to conrm your selection.
To change your time zone upon setup:
Press / until your own time zone appears on the display; press ONCE to
conrm your selection.
To change your time zone after setup:
Press and hold the SNOOZE/SLEEP/DIMMER button until numbers ash.
Press / until your own time zone appears on the display; press ONCE to
conrm your selection.
There are 8 programmed times zones:
BATTERY BACKUP
This alarm clock is equipped with a battery backup feature. This feature will restore your
alarm clock settings in the event of a power outage. The 3V, CR2032 Flat Lithium battery
is pre-installed at the factory, however, should you need to replace the battery, please
read the following instructions.
Zone 0 - Newfoundland time
Zone 1 - Atlantic time
Zone 2 - Eastern time (default)
Zone 3 - Central time
Zone 4 - Mountain time
Zone 5 - Pacic time
Zone 6 - Alaska time
Zone 7 - Hawaiian time
OPERATING INSTRUCTIONS
- 13 -
Zone 6 - Alaska time
Zone 7 - Hawaiian time
OPERATING INSTRUCTIONS
INSTALLING THE BATTERY
1. Using a small Phillips Head screwdriver, remove the screw from the battery panel
on the bottom of the unit.
2. Remove the battery compartment panel.
3. Remove/properly dispose of depleted battery and replace with new, 3V, CR2032
Flat Lithium battery.
4. Close the battery compartment and put screw into place to secure battery panel.
ATTENTION
When replacing the battery, do not disconnect AC plug from AC outlet. Current time and alarm will be initialized.
Do not plug or unplug the power cable if you have wet hands.
If you are not planning to use the unit for an extended period of time, disconnect the power cable from the wall outlet.
Do not pull on the cord! You may damage the power cord and may cause an electric shock when disconnecting the
power cord from the wall outlet. Pull rmly at the base of the plug.
DAYLIGHT SAVING TIME DST / SUMMER TIME
Daylight Saving Time/Summer Time is automatically preset.
Daylight saving time begins at: 2:00 AM on the second Sunday of March.
Standard time begins at: 2:00 AM on the rst Sunday of November.
Cancelling / reactivating Automatic DST/Summer Time
1. To CANCEL DST/Summer Time, press and hold the DST/°C °F button for
3 seconds while the radio is OFF.
2. 'OFF' will appear in the display to show that the Automatic DST/Summer Time
adjustment is cancelled. The display will return to the clock.
Batteries must be installed by an adult.
Use only the recommended size and type of battery specied.
Please be sure to follow the correct polarity when installing the battery in the battery
compartment. A reversed battery may cause damage to the alarm clock.
When not using the unit for a prolonged period of time, please remove the batteries to
avoid possible damage caused by leaking batteries.
- 14 -
OPERATING INSTRUCTIONS
3. To REACTIVATE DST/Summer Time, press and hold the DST/°C °F button for 3
seconds while the radio is OFF.
4. 'ON' will appear in the display to show that the Automatic DST/Summer Time
adjustment is reactivated. The display will return to the clock.
SETTING THE DATE & TIME
To change the Date/Time, press and hold the button. The settings below will
appear in the following order:
Year > Month > Day > 12/24 H > Hour > Min
1. Press the button to DECREASE numbers or to toggle through settings.
2. Press the button to INCREASE numbers or to toggle through the dierent
settings.
3. To conrm your selection, press the button once again.
The timing of Automatic DST/Summer Time employed by the unit (see above) is
subjected to variations by region and the law in each country/region. In such a
case, cancel the Automatic DST/Summer Time adjustment.
If you live in a country/region that has not introduced Daylight Saving Time/
Summer Time, you must cancel Automatic DST/Summer Time adjustment before
using the unit.
LED dot appears to the right of PM indicating time is set to PM; no dot for AM.
Pressing the or the buttons once, decreases/increases one number
at a time.
Pressing and holding the or the buttons quickly decreases/increases
the numbers.
OPERATING INSTRUCTIONS
- 15 -
SETTING ALARM 1 & ALARM 2
To set ALARM 1, press and hold the
button and alarm time will ash. The settings
below will appear in the following order:
AL 1 Hour > AL 1 Min > AL 1 Alarm Modes > AL 1 Wake Options > AL 1 Radio Volume
1. Press the
/ buttons to decrease/increase the HOUR; press the
button to conrm HOUR. The MINUTES will begin to ash.
2. Press the
/ buttons to decrease/increase the MINUTES; press the
button to conrm MINUTES. ALARM MODES will ash.
ALARM MODES allows you to set more than one alarm in a week i.e. ALARM 1 set to
wake you Monday-Friday and ALARM 2 set to wake you on weekends. The ALARM MODE
settings are as follows:
1-5 : Monday to Friday 3: Wednesday
1-7 : Whole week 4: Thursday
6-7 : Saturday & Sunday 5: Friday
1 : Monday 6: Saturday
2 : Tuesday 7: Sunday
3. Press the / buttons to toggle between the ALARM MODE settings then press
the
button to conrm your selection. The WAKE OPTIONS will begin to ash.
4. Press the / buttons to toggle between the WAKE OPTIONS AM, FM or
BELL; press the
button to conrm your selection. If AM or FM is selected the
Radio Volume selection will begin to ash.
5. Press the / buttons to decrease/increase the Radio Volume; press the
button to conrm your selection, and complete the alarm set up.
6. Alarm will be armed once alarm setup is completed.
OPERATING INSTRUCTIONS
- 16 -
SETTING ALARM 2
To set ALARM 2, press and hold the button and alarm time will ash. The settings
below will appear in the following order:
AL 2 Hour > AL 2 Min > AL 2 Alarm Modes > AL 2 Wake Options > AL 2 Radio Volume
1. Press the / buttons to decrease/increase the HOUR; press the button
to conrm HOUR. The MINUTES will begin to ash.
2. Press the / buttons to decrease/increase the MINUTES; press the
button to conrm MINUTES. ALARM MODES will ash.
ALARM MODES allows you to set more than one alarm in a week i.e. ALARM 1 set to
wake you Monday-Friday and ALARM 2 set to wake you on weekends. The ALARM MODE
settings are as follows:
1-5 : Monday to Friday 3: Wednesday
1-7 : Whole week 4: Thursday
6-7 : Saturday & Sunday 5: Friday
1 : Monday 6: Saturday
2 : Tuesday 7: Sunday
3. Press the / buttons to toggle between the ALARM MODE settings then
press the button to conrm your selection. The WAKE OPTIONS will begin to ash.
4. Press the / buttons to toggle between the WAKE OPTIONS AM, FM or
BELL; press the button to conrm your selection. If AM or FM is selected the
Radio Volume selection will begin to ash.
5. Press the / buttons to decrease/increase the Radio Volume; press the
button to conrm your selection, and complete the alarm set up.
6. Alarm will be armed once alarm setup is completed.
To deactivate ALARM 1 and/or ALARM 2, tap the button and/or the button until
the LED is no longer visible on the front LED panel.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
- 17 -
OPERATING INSTRUCTIONS
ALARM DURATION
The BUZZER alarm or RADIO alarm will sound for 30 minutes if no key is pressed, then
it will stop automatically and resume to the same alarm time on next scheduled day. To
stop ALARM 1 and/or ALARM 2 when sounding, press the button on the front of the
unit.
SNOOZE FUNCTION
When alarm is sounding, press the SNOOZE/SLEEP button to stop alarm for 9 minutes.
Alarm will resume after 9 minutes.
Pressing the button on the front of the unit will CANCEL the Snooze function
Snooze function will also stop automatically after 30 minutes.
SLEEP TIMER
The sleep timer allows you to listen to music for a preset amount of time ranging from 90
minutes to 15 minutes. It is commonly used by people who prefer to fall asleep to music.
1. Press the button to turn the radio 'ON'.
2. Press the SNOOZE/SLEEP button to toggle through the preset times;
90min > 60min > 30min > 15min > OFF
3. To cancel the SLEEP timer, press the SNOOZE/SLEEP button until you see OFF in
the display or press the button to turn o the radio.
OPERATING INSTRUCTIONS
- 18 -
ADJUSTING LED BRIGHTNESS
You can adjust the brightness of the LED display making it brighter, dimmer or even
turning it OFF when the radio is OFF. There are four dimming options available: HIGH/
MEDIUM/LOW/OFF Standby. Press the DIMMER button to toggle between the four
brightness settings.
LISTENING TO THE RADIO
1. Press the button on the front panel to turn the radio 'ON'.
2. Press and hold the AM / FM button to toggle between AM and FM radio bands.
3. Press the / buttons once, to move back/move forward one station at a
time.
4. Press and hold the / buttons for one second to scan back/forward through
the stations; the unit will automatically scan to the next broadcasting station.
5. Press the button on the front panel to turn the radio 'OFF'.
Please ensure that the FM antenna is completely unrolled and extended for best FM reception. The
AM band uses an internal directional aerial. For best reception, please rotate the radio.
TO SET / RECALL THE RADIO PRESETS
1. Press the button on the front panel to turn the radio 'ON'.
2. Press and hold the AM / FM button to toggle between AM and FM radio bands.
3. Use the / buttons to select the desired radio station.
4. Press and hold the PRESETS button; 'P02' will blink in the display.
5. Use the / buttons to toggle to the desired preset 'P01-P10' number.
6. Press the PRESETS button again to set the preset.
7. Repeat steps 2 through 4 to set more presets.
8. To select a preset station, press the PRESETS button until desired preset station
appears on the LED panel.
The unit supports up to 10 AM & 10 FM preset stations.
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
- 19 -
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
USB CHARGING FUNCTION
This alarm clock is equipped with a convenient USB charging port on the back panel
that allows you to recharge many brands of smartphones, tablets and portable music
players. To charge your device, connect the USB charging cable that is connected to your
handheld device to the USB charging port on the back panel of this alarm clock.
Charging time will vary depending on the charging current that your device requires.
Therefore, some devices will take longer to charge than others.
- 20 -
Please consult the Troubleshooting chart below before communicating with
ELECTROHOME Customer Support.
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION
GENERAL
Power does not come on AC cord not plugged in Insert plug rmly into AC outlet
RADIO
No Sound Power is not on
Press the button
VOLUME control at minimum
position
Turn the VOLUME control up
1. Disconnect the unit from any power sources before cleaning.
2. Keep the unit away from magnetic objects, water or heat sources.
3. Clean only with a dry cloth.
TROUBLESHOOTING
CARE AND MAINTENANCE
SPECIFICATIONS
Noise or sound distorted
on AM or FM
AM-interference from trac Tune the radio for better AM reception
FM-antenna wire not extended Extend antenna wire
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION
CLOCK
Incorrect Time Clock not set Set the clock
Battery is inserted incorrectly,
or depleted
Check/replace the battery
Alarm does not turn on Alarm is not set to turn on
Activate ALARM 1 or ALARM 2
Clock is not set Set the clock
Alarm time is not set Set alarm time for
ALARM 1 or ALARM 2
No display Dimmer is set to Standby Mode Press Dimmer button
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47

Electrohome ELEEAAC470 Manuel utilisateur

Catégorie
Réveils
Taper
Manuel utilisateur

dans d''autres langues