Omcan BS-CN-1651-T Manuel utilisateur

Revised - 05/05/2022

Toll Free: 1-800-465-0234

Fax: 905-607-0234

Email: [email protected]

www.omcan.com

Band Saws

Models BS-CN-1651-T, 2020, 2400

Items 46785, 46786, 46787

Instruction Manual

2

Page

--------------------------------------------------------------------------- 3 - 4

--------------------------------------------------------------------------- 4 - 5

-------------------------------------------------------------------------- 6

--------------------------------------------------------------------------------------- 6 - 7

--------------------------------------------------------------------------------------------- 7

------------------------------------------------------------------------------------- 7 - 8

----------------------------------------------------------------------------- 9 - 13

---------------------------------------------------------------------- 14 - 15

------------------------------------------------------------------------------------------- 16 - 18

---------------------------------------------------------------------------- 19

Table of Contents

Section

General Information

Safety and Warranty

Technical Specications

Installation

Operation

Maintenance

Parts Breakdown

Electrical Schematics

Notes

Warranty Registration

Model BS-CN-1651-T / Model BS-CN-2020 / Model BS-CN-2400

3

General Information

Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan

and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or

negligent use of this equipment. The product shall only be operated by someone over the age of 18, of

sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct

operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the

machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of

the machine while in operation.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the

external packaging, open carton to ensure all ordered items are within the box, and there is no concealed

damage to the machine. If the package has suered rough handling, bumps or damage (visible or concealed),

please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may

initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be

lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse

for damaged products that were shipped collect or third party.

Before operating any equipment, always read and familiarize yourself with all operation and safety

instructions.

Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save

these instructions for future reference. Also save the original box and packaging for shipping the

equipment if servicing or returning of the machine is required.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et

Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne

ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de

plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour

utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication

de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine

ou des personnes à proximité de la machine pendant son fonctionnement.

VÉRIFIEZ LE COLIS DÈS RÉCEPTION

Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage

n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés

sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises

manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant

d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager

une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine

doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents

d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli

par un tiers transporteur.

4

General Information

Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations

et les consignes de sécurité.

Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces

instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour

l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba

Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona

inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona

mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido

entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.

Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la

máquina mientras esta en el funcionamiento.

REVISE EL PAQUETE A SU LLEGADA

Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el

empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la

caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes

o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro

de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre

los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se

muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron

a recoger por terceros.

Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de

funcionamiento y seguridad.

Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para

salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el

envío del equipo si servicio técnico o devolución de la máquina que se requiere.

Safety and Warranty

WARNING

Please use the machine according to these cautions. The user should understand all safety rules, please

carefully read this instruction manual before operating the machine. Do not remove or change the safety

equipment prior to operating the machine, doing so will void the warranty and cause serious harm to yourself

and others. We are not responsible for any injuries sustained by incorrect usage of the machine.

5

Safety and Warranty

CONDITIONS FOR USE

• This machine is used for cutting fresh meat, bone and frozen sh. If you want to cut frozen meat and

bones, the correct saw blade must be used.

• This machine should only be used for the purposes mentioned in this manual.

• Service life of saw blade depends on the product it cuts and the pressure used. Usually, the service life

standard is between 1000 kgs to 2000 kgs per blade but, if the machine is used on fresh meat only (without

the bone), the blades can be used longer.

• Please read the manual entirely and operate the unit according to the information stated within it.

• Do not use the machine if the door is open or if any of the security devices are not functional.

RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure

or other damages resulting from installation in non-commercial or residential applications. The right

is reserved to deny shipment for residential usage; if this occurs, you will be notied as soon as

possible.

1 YEAR PARTS AND LABOUR WARRANTY

Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized

service technician to repair the equipment locally.

Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures not

improper use.

Please see https://omcan.com/disclaimer for complete info.

WARNING:

The packaging components are classied as normal solid urban waste and can therefore be disposed of

without diculty.

In any case, for suitable recycling, we suggest disposing of the products separately (dierentiated

waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

6

Technical Specications

Installation

Model BS-CN-1651-T BS-CN-2020 BS-CN-2400

Electrical 110V / 60Hz / 1 220V / 60Hz / 3

Power 750W 1500W 2200W

Diameter of Wheel 8.3” / 211mm 9.8” / 250mm 11.8” / 300mm

Length of Saw 65” / 1651mm 79.5” / 2020mm 94.5” / 2400mm

Material of Saw High-Carbon Steel

Line Speed of Saw

Blade 16m/s 18.8m/s 22.6m/s

Dimensions of Working

Table

17.3” x 18.3”

440 x 465mm

22.2” x 26.3”

565 x 668mm

30.2” x 29.1”

767 x 738mm

Thickness of Table 0.1” / 3mm 0.2” / 4mm

Max Slicing Thickness 6.3” / 161mm 8” / 202mm 9.9” / 252mm

Max Height of Cutting 9.4” / 238mm 12” / 304mm 14” / 355mm

Speed of Motor 1400r/min

Weight 89.5 lbs. / 40.6 kgs. 265.4 lbs. / 120.4 kgs. 310.9 lbs. / 141 kgs.

Packaging Weight 126.1 lbs. / 57.2 kgs. 340.8 lbs. / 154.6 kgs. 409 lbs. / 185.5 kgs.

Packaging Dimensions 19.7” x 20.5” x 40.2”

550 x 520 x 1020mm

26.4” x 29.3” x 63”

670 x 745 x 1600mm

32.3” x 34.4” x 68.3”

820 x 875 x 1735mm

Item Number 46785 46786 46787

Place the machine in a stable and at location. Especially when assembling or disassembling. If the surface

is not completely at,you can adjust the rubber feet to compensate. Please ensure that the power supply is

the same as indicated on the rating label and is properly grounded. Please ensure that the power cable is

long enough to reach the power source comfortably and that the cable is not damaged. When the machine is

opened by the user, please inspect the saw belt length on the top and bottom block, it is must be parallel with

the edge of the block. Close the machine’s door and connect to the power source, turn on the green switch,

and then the machine is ready for operation. If you turn o the red switch, the machine will shut down.

PLEASE ENSURE THE BELOW AT ALL TIMES:

1. The machine should be running correctly (clockwise).

2. If the saw blade is loose, please turn the handle on the top until tightened. When properly tightened, the

machine will slice correctly and can now be operated safely.

NOTES:

1. During installation, please pay attention to direction of the blade, the blade must be facing the correct

direction.

2. The scraper must be installed properly with the saw blade. If it is improperly installed, it will cause more

7

Operation

Installation

When operating, use the push handle located between the bone band and push button, hold the handle rmly.

Carefully use your other hand to steady the meat, and push the meat towards the blade with the safety device.

The machine will cut through the meat with ease. Do not use your hands to push the meat through the saw.

When the meat has been cut, pull the handle back and reset the meat carefully. Repeat as needed until the

meat cannot be safely cut.

Never attempt to push the meat through the saw without the safety devices.

noise than normal and decrease life of the blade.

3. When the door of the machine is opened, the machine will stop operation by itself. Use extreme caution as

the blade is sharp.

4. Wear safety gloves that are resistant to cuts whenever operating or performing maintenance with this

machine.

5. Do not us this machine to cut small pieces of meat. Doing so will be hazardous, even with cut resistant

gloves.

Maintenance

REPLACING THE SAW BLADE

To replace the saw blade, please loosen it by turning the tightener counter-clockwise. Carefully remove the old

saw blade and replace it with the new blade. Please pay attention to the direction of the blade to ensure that

it will cut properly. Ensure that the saw blade and slicer are installed between the top wheel, bottom pulley,

middle plate and pass through guide groove.

Note: There are dierent blades needed for dierent types of meat. Ensure that you are installing the

correct blade for your desired purpose.

ADJUSTING THE SAW BLADE

If the blade is not aligned properly, simply loosen the blade and carefully shift the blade to the correct position.

Once adjusted, simply tighten the blade. Always ensure that the blade can move normally before operating.

CLEANING

Always turn o the unit and unplug from the power source before cleaning the machine. Open the door of

machine, loosen and remove the saw blade. Loose the scraper protection knob in order to remove the scraper.

8

Maintenance

Clean with hot water and a sti brush.

You can also use a hot damp towel to clean the main spare parts, blade and protective devices. Use a dry cloth

to wipe away all residual water.

Special attention should be made in ensuring that the dead angle, wheel, chain wheel and bottom parts are

also carefully cleaned.

Do not use water jets or sprays to clean the machine. Do not immerse any part of the machine in water. Doing

so will cause an electrical hazard.

MAINTENANCE

After every 200 working hours, it is advised to use some food safe machine lubricant on the guide apparatus of

the tightening device. After 5000 working hours, we suggest to replace the wheel bearings.

9

Parts Breakdown

Model BS-CN-1651-T 46785

10

Parts Breakdown

Model BS-CN-1651-T 46785

Item No. Description Position Item No. Description Position Item No. Description Position

AF326 Cover for Motor for 46785 1 AF346 Table for 46785 21 AF366 Bottom for 46785 41

AF327 Cap Nut for 46785 2 AF347 Axis for 46785 22 AF367 Wire and Cord for 46785 42

AF328 Flat Gasket for 46785 3 AF348 Small Axis for 46785 23 AF368 Line Card for 46785 43

AF329 Rubber Gasket (Jacket) for 46785 4 AF349 Wheel for 46785 24 AF369 Electric Box (Include Contactor) for

46785 44

AF330 Pole for 46785 5 AF350 Saw for 46785 25 AF370 Body for 46785 45

AF331 Back Cover for 46785 6 AF351 Bearing for 46785 26 AF371 Length Plate for 46785 47

AF332 Motor for 46785 7 AF352 O Ring for 46785 27 AF372 Axis for Adjusting for 46785 48

AF333 Guide Plate for 46785 8 AF353 Gland for 46785 28 AF373 Supporting for Scraper for 46785 49

AF334 Adjusting Slider for 46785 9 AF354 Door for 46785 29 AF374 Seat for Scraper for 46785 50

AF335 Top Cover for 46785 10 AF355 Mouthpiece Board for 46785 30 AF375 Scraper for 46785 51

AF336 Locking Nut for 46785 11 AF356 Shaft Seat for 46785 31 AF376 Handle for 46785 52

AF337 Spring for 46785 12 AF357 Screw for 46785 32 AF377 Angle Iron for 46785 53

AF338 Adjusting Handle for 46785 13 AF358 New Knob for 46785 33 AF378 Turning Axis for 46785 54

AF339 Steel Ball for 46785 14 AF359 Case for Roumo for 46785 34 AF379 Angle Iron for 46785 55

AF340 End Cover for 46785 15 AF360 Supporting Plate for 46785 35 AF380 Microswitch for 46785 56

AF341 Switch for 46785 16 AF361 Locking Board for Switch for 46785 36 AF381 Shaft Collar for 46785 57

AF342 Shaft Ring for 46785 17 AF362 Wheel for 46785 37 AF382 Stand for Scraper for 46785 58

AF343 Knob for 46785 18 AF363 Mouthpiece Board for 46785 38 AF383 Scraper for 46785 59

AF344 Channel Iron for 46785 19 AF364 Backplane for 46785 39

AF345 Guide Shaft for 46785 20 AF365 Leg for 46785 40

11

Parts Breakdown

Model BS-CN-2020 46786

Model BS-CN-2400 46787

12

Parts Breakdown

Model BS-CN-2020 46786

Item No. Description Position Item No. Description Position Item No. Description Position

AF384 Cover for 46786 1 AF412 Stand for 46786 29 AF440 Shaft for 46786 57

AF385 Nut for 46786 2 AF413 Cleaner 1 for 46786 30 AF441 Sliding Plate of Groove for 46786 58

AF386 Gasket for 46786 3 AF414 Cleaner 2 for 46786 31 AF442 Protection of Moving for 46786 59

AF387 Spring for 46786 4 AF415 Handle for 46786 32 AF443 Moving Guide Shaft for 46786 60

AF388 Adjusting Handle for 46786 5 AF416 Sliding Working Table for 46786 33 AF444 Guide Part for 46786 61

AF389 Sheath for 46786 6 AF417 Cover for 46786 34 AF445 Rubber Gasket for Switch for 46786 62

AF390 Round Ball for 46786 7 AF418 Bakelite Handle for 46786 35 AF446 Length Board for 46786 63

AF391 Lid Cover for 46786 8 AF419 Collar for Top Shaft for 46786 36 AF447 Tightening Screw for 46786 64

AF392 Tightening Shaft for 46786 9 AF420 Pulley 2 for 46786 37 AF448 Bending Board for 46786 65

AF393 Pin for 46786 10 AF421 Bottom for 46786 38 AF449 Support Frame of Motor for 46786 66

AF394 Spring for 46786 11 AF422 Adjusting Feet for 46786 39 AF450 Waste Setting (Selected) for 46786 67

AF395 Bushing for 46786 12 AF423 Non-Adjusting Feet for 46786 40 AF451 Hexagon Screw for 46786 69

AF396 Box of Switch for 46786 13 AF424 Seat for 46786 41 AF452 Big Gasket for 46786 70

AF397 Stop Button for 46786 14 AF425 Body for 46786 42 AF453 Seat of Transform for 46786 71

AF398 Start Button for 46786 15 AF426 Drawer for Waste for 46786 43 AF454 Star Handle for 46786 72

AF399 Locker for 46786 16 AF427 Door for 46786 44 AF455 Hexagon Screw for 46786 73

AF400 Handle of Locker for 46786 17 AF428 Protection for Saw for 46786 45 AF456 Fixing Stand for 46786 74

AF401 Retaining Plate for 46786 18 AF429 Shaft for 46786 46 AF457 Shaft for 46786 75

AF402 Pulley 1 for 46786 19 AF430 Protection for Saw for 46786 47 AF458 Nut for 46786 76

AF403 Shaft of Pulley for 46786 20 AF431 Shaft for 46786 48 AF459 Gasket for 46786 77

AF404 Sealing Ring for 46786 21 AF432 Back Cover for 46786 49 AF460 Handle for 46786 78

AF405 Bearing for 46786 22 AF433 Motor for 46786 50 AF461 Moving Shaft for 46786 79

AF406 Spacer for 46786 23 AF434 Microswitch for 46786 51 AF462 Clamping Plate 1 for 46786 80

AF407 Shaft for 46786 24 AF435 Contacting and Capacitor for 46786 52 AF463 Seat with Drawer for 46786 81

AF408 Collar for Shaft for 46786 25 AF436 Handle for 46786 53 AF464 Drawer for 46786 82

AF409 O Ring for 46786 26 AF437 Cover of Back for 46786 54 AF465 Cover for Door for 46786 83

AF410 Gland for 46786 27 AF438 Guiding Part for 46786 55

AF411 Saw for 46786 28 AF439 Sliding Part for 46786 56

13

Parts Breakdown

Model BS-CN-2400 46787

Item No. Description Position Item No. Description Position Item No. Description Position

AF384 Cover for 46787 1 AF412 Stand for 46787 29 AF440 Shaft for 46787 57

AF385 Nut for 46787 2 AF413 Cleaner 1 for 46787 30 AF441 Sliding Plate of Groove for 46787 58

AF386 Gasket for 46787 3 AF414 Cleaner 2 for 46787 31 AF442 Protection of Moving for 46787 59

AF387 Spring for 46787 4 AF415 Handle for 46787 32 AF443 Moving Guide Shaft for 46787 60

AF388 Adjusting Handle for 46787 5 AF468 Sliding Working Table for 46787 33 AF444 Guide Part for 46787 61

AF389 Sheath for 46787 6 AF469 Cover for 46787 34 AF445 Rubber Gasket for Switch for 46787 62

AF390 Round Ball for 46787 7 AF418 Bakelite Handle for 46787 35 AF479 Length Board for 46787 63

AF391 Lid Cover for 46787 8 AF419 Collar for Top Shaft for 46787 36 AF447 Tightening Screw for 46787 64

AF392 Tightening Shaft for 46787 9 AF470 Pulley 2 for 46787 37 AF448 Bending Board for 46787 65

AF393 Pin for 46787 10 AF421 Bottom for 46787 38 AF480 Support Frame of Motor for 46787 66

AF394 Spring for 46787 11 AF422 Adjusting Feet for 46787 39 AF450 Waste Setting (Selected) for 46787 67

AF395 Bushing for 46787 12 AF423 Non-Adjusting Feet for 46787 40 AF451 Hexagon Screw for 46787 69

AF396 Box of Switch for 46787 13 AF471 Seat for 46787 41 AF452 Big Gasket for 46787 70

AF397 Stop Button for 46787 14 AF472 Body for 46787 42 AF453 Seat of Transform for 46787 71

AF398 Start Button for 46787 15 AF473 Drawer for Waste for 46787 43 AF454 Star Handle for 46787 72

AF399 Locker for 46787 16 AF474 Door for 46787 44 AF455 Hexagon Screw for 46787 73

AF400 Handle of Locker for 46787 17 AF428 Protection for Saw for 46787 45 AF456 Fixing Stand for 46787 74

AF401 Retaining Plate for 46787 18 AF429 Shaft for 46787 46 AF481 Shaft for 46787 75

AF402 Pulley 1 for 46787 19 AF430 Protection for Saw for 46787 47 AF458 Nut for 46787 76

AF403 Shaft of Pulley for 46787 20 AF431 Shaft for 46787 48 AF459 Gasket for 46787 77

AF404 Sealing Ring for 46787 21 AF475 Back Cover for 46787 49 AF460 Handle for 46787 78

AF405 Bearing for 46787 22 AF476 Motor for 46787 50 AF461 Moving Shaft for 46787 79

AF406 Spacer for 46787 23 AF434 Microswitch for 46787 51 AF462 Clamping Plate 1 for 46787 80

AF466 Shaft for 46787 24 AF435 Contacting and Capacitor for 46787 52 AF482 Seat with Drawer for 46787 81

AF408 Collar for Shaft for 46787 25 AF436 Handle for 46787 53 AF483 Drawer for 46787 82

AF409 O Ring for 46787 26 AF477 Cover of Back for 46787 54 AF484 Cover for Door for 46787 83

AF410 Gland for 46787 27 AF438 Guiding Part for 46787 55

AF467 Saw for 46787 28 AF478 Sliding Part for 46787 56

14

Electrical Schematics

Model BS-CN-1651-T 46785

15

Electrical Schematics

Model BS-CN-2020 46786

Model BS-CN-2400 46787

16

Notes

________________________________________________________________________________________

17

Notes

________________________________________________________________________________________

18

Notes

________________________________________________________________________________________

19

Warranty Registration

Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,

cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:

Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la

carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear o the card at

the perforation and then send to the address specied below. You can also register online by visiting:

OMCAN

PRODUCT WARRANTY REGISTRATION

3115 Pepper Mill Court,

Mississauga, Ontario

Canada, L5L 4X5

https://omcan.com/warranty-registration/

or email to: [email protected]

Purchaser’s Information

Name: Company Name:

Address:

Telephone:

City: Province or State: Postal or Zip: Email Address:

Country: Type of Company:

Restaurant Bakery Deli

Dealer from which Purchased: Butcher Supermarket Caterer

Dealer City: Dealer Province or State: Institution (specify):

Invoice: Other (specify):

Model Name: Model Number: Serial Number:

Machine Description:

Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Would you like to extend the warranty? Yes No



Por correo en Canadá

Pour postale au Canada

For mailing in Canada

Por correo en los EE.UU.

Pour diusion aux États-Unis

For mailing in the US

OMCAN

PRODUCT WARRANTY REGISTRATION

4450 Witmer Industrial Estates, Unit 4,

Niagara Falls, New York

USA, 14305

Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North

American food service industry. Our success over these many years can be attributed to our commitment

to strengthen and develop new and existing relationships with our valued customers and manufacturers.

Today with partners in North America, Europe, Asia and South America, we continually work to improve

and grow the company. We strive to offer customers exceptional value through our qualied local sales

and service representatives who provide convenient access to over 6,500 globally sourced products.

Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et

matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces

nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles

et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en

Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et

développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à

nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 6500

produits provenant du monde entier.

Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros

de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir

a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos

clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan

continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor

excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un

fácil acceso a más de 6,500 productos con origen a nivel mundial.

Omcan BS-CN-1651-T Manuel utilisateur

Omcan BS-CN-1651-T Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents