Marvel 30WCM768 Mode d'emploi

Marque: Marvel

Modèle: 30WCM768

Catégorie: Boissons glacées

Taper: Mode d'emploi

Wine Cellars

Celliers

ML15WSG0**

ML24WSG0**

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

Note: Wine Cellars are designed exclusively for the

storage of wine. Wine Cellars cannot attain storage

temperatures suitable for fresh food storage.

Remarque : Les celliers sont conçues exclusivement

pour y garder des vins. Elles ne peuvent pas atteindre des

températures de conservation convenant à l’entreposage

d’aliments frais.

NOTE

CAUTION

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product dimensions ............................................................8

Using your Electronic control ............................................10

Starting your refrigerator ...............................................10

Turning your refrigerator "ON" or "OFF" .......................10

Set temperature ...........................................................10

Refrigerator operation ...................................................10

Alarms ...........................................................................10

Door ajar ..................................................................10

Temperature sensor fault .........................................10

Alarm mute ...................................................................10

Shelving congurations ....................................................11

Care and cleaning .............................................................13

Energy saving tips ............................................................14

Obtaining service .............................................................14

Troubleshooting ................................................................15

Warranty ...........................................................................16

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

NOTE

CAUTION

XXXXXXXXXXXX

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

MARVEL

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Warranty Registration

UNPACKING YOUR APPLIANCE

Online registra-

tion available at

www.marvelrefrig-

eration.com

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See gure 1).

Figure 1

CAUTION

WARNING

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed.

An optional stacking kit, for 24" wide models, is re-

quired to stack products. Failure to use a stacking kit

could result in personal injury. Contact your dealer or

Marvel customer service at 800-223-3900 to order.

For safety concerns 15" wide models should not be

stacked.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use

of a custom made grille as air ow may be restricted. (See

Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW) dimensions as shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

Rear

Leveling

Legs

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Model Door Style

Minimum

Height

Maximum

Height

ML(15)(24)* (G)

⁄4"

(85.7 cm)

⁄4"

(88.3 cm)

Table A

NOTE

INSTALLING YOUR APPLIANCE

Front grille

Front grille screw

Figure 5

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

Step by step instructions for locating the po-

sition of the bracket:

1) Decide where you want to place the wine cellar. Slide it

into place, being careful not to damage the oor, leaving 1"

(2.5 cm) of clearance from the rear wall to allow room for

the anti-tip bracket.

2) Raise the rear leveling legs approximately

⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the wine cellar is in the desired location, then

mark on the oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the oor marking the front corner

of the cabinet, excluding the door. Slide the wine cellar out

of the way. From the temporary line extend the sidewall

line back 21

⁄2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the

rear cabinet leveling leg slides under the anti-tip bracket

engaging the slot.

Front of cabinet

Figure 7

⁄2"

(54.6 cm)

Anti-Tip

Bracket

Leveling Leg

Bottom View of

Wine Cellar

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the wine cellar as shown in Figure 7.

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

CAUTION

NOTE

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

Anti-Tip Device

WARNING

If your wine cellar is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the wine cellar is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the wine cellar back into the

original location. If the device is not properly engaged,

there is a risk of the wine cellar tipping over, with the

potential for property damage or personal injury.

NOTE

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

When the oor mounted anti-tip bracket is used the mini-

mum adjusted height of the cabinet is increased by

⁄8" (9 mm).

Figure 8a

"V" notches

in bracket

"V" notches

in bracket

Figure 8

⁄2"

(54.6 cm)

Front of cabinet line

Rear Leveling leg

Side of cabinet line

Rear of cabinet line

Screw

"A"

"B"

"C"

"D"

"E"

PRODUCT DIMENSIONS

MODEL

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

"A" "B" "C" "D" "E" "F" "G" "H" "J" "K"

ML15WSG

15"

(38.1 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

⁄8"

(37.8 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄32"

(59.1 cm)

⁄32"

(64.1 cm)

37"

(94 cm)

⁄16"

(39.5 cm)

⁄16"

(53.8 cm)

ML24WSG

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

⁄8"

(60.7 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄16"

(61.1 cm)

26"

(66 cm)

47"

(119.4 cm)

⁄32"

(65.2 cm)

22"

(55.9 cm)

DOOR STYLE

(G) Glass Frame Door

Figure 9

Figure 9a

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

Figure 10

"F"

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

MODEL

PRODUCT DATA

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

ML15WSG 115V/60Hz/15A

100 lbs

(45.4 kg)

ML24WSG 115V/60Hz/15A

130 lbs

(59.1 kg)

WARNING

Floor mount Anti-tip Bracket must be installed for freestand-

ing applications. Not required for built in applications.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

Figure 11

"K"

(2.5 cm)

USING YOUR ELECTRONIC CONTROL

Starting your refrigerator

Plug the refrigerator power cord into a wall outlet. Your

refrigerator will begin cooling after power is applied.

If your refrigerator does not start, check that the refrigerator

is turned on and the set temperature is cold enough.

Turning your refrigerator ON or OFF

If the refrigerator is on, the refrigerator temperature will be

shown on the display. To turn the refrigerator off, press and

hold the “ON/OFF” button for three (3) seconds. “OFF” will

appear on the display.

If the refrigerator is not on, “OFF” will be shown on the

display. To turn the refrigerator on, press and hold the “ON/

OFF” button for three (3) seconds. The refrigerator tem-

perature will be shown on the display.

Set temperature

To set the refrigerator temperature, press and hold the

“SET” button. When the “SET” button is pressed, the dis-

play will show the set temperature. While holding the “SET”

button, press the “WARMER” or “COLDER” buttons to

adjust set temperature.

Refrigerator operation

The available temperature range of the refrigerator is 40° to

65° (4° to 18° C).

It may take up to 24 hours for your refrigerator to reach

desired temperature. This will depend on amount of content

loaded and number of door opening and closings.

For best results allow refrigerator to “pull down” to desired

set temperature before loading. Once contents are loaded,

allow at least 48 hours for temperature to stabilize before

making any adjustments to the set temperature.

Alarms

Your MicroSentry™ refrigerator control will monitor refrig-

erator function and alert you with a series of audible and

visual alarms.

• Door Ajar Alarm: If the door has been left

open for over ve (5) minutes, the alarm

will sound in one (1) second intervals. The

display panel will ash “do” and the Alarm LED located at

the top left of the display below the word “Alarm” will be il-

luminated. This will stop as soon as the door is closed.

• Temperature Sensor Fault: If the controller

detects that the temperature sensor is

not properly functioning, a temperature

sensor alarm will sound in one (1) second intervals. “E1”

will ash on the display panel and the Alarm LED located

at the top left of the display below the word “Alarm” will be

illuminated. Please call Marvel Customer Service or your

dealer if this error code is displayed.

Alarm Mute

Press any key to mute the audible portion of an alarm.

This action will only mute the alarm. If the condition that

caused the alarm continues, the alarm code will continue to

ash and will sound for 20 seconds every 60 minutes.

Figure 12

Control

Door Switch

NOTE

SHELVING CONFIGURATION ML15WSG

Insert Wine Bottles

The ve (5) pull-out shelves each hold four (4) bottles. See

Figure 13 for typical wine bottle spacing. Care should be

taken when storing extra tall bottles in the wine cradle at

the bottom of the compartment because they may prevent

the door from closing.

Loading Tips and Suggestions

The bottles on the top rack directly under the light will be

exposed to a slightly higher temperature when the light is

on. Position your wines accordingly and REMEMBER TO

TURN OFF THE LIGHT WHEN IT IS NO LONGER NEED-

ED.

Keep wines that you plan to use for everyday drinking and

entertaining on the front half of the racks where labels are

completely visible. Place wines for aging or longer term

storing in the rear.

Pull-out Racks

The ve (5) pull-out wine racks may be pulled out approxi-

mately seven (7) inches to facilitate adding or removing

bottles. DO NOT lean on or press down heavily on the

wine shelves. Doing so may damage the shelves and the

wine bottles stored on them. Pull the wine racks out gently

and carefully to minimize unsettling your wine collection.

Avoid pulling out more than one rack at any time to main-

tain stability.

Single Bottle Racks

The single level roll out racks allow you to easily view and

access your inventory without disturbing other bottles (see

Figure 15).

Figure 14

Figure 15

Front Bottles (Necks Facing Rear)

Rear Bottles (Necks Facing Front)

Figure 13

SHELVING CONFIGURATION ML24WSG

Insert Wine Bottles

The four (4) pull-out shelves each hold eight (8) bottles.

See Figure 16 for typical wine bottle spacing. Care should

be taken when storing extra tall bottles in the wine cradle at

the bottom of the compartment because they may prevent

the door from closing.

Loading Tips and Suggestions

Two (2) magnums can be placed in the bottle cradle as

long as they are positioned horizontally.

The bottles on the top rack directly under the light will be

exposed to a slightly higher temperature when the light is

on. Position your wines accordingly and REMEMBER TO

TURN OFF THE LIGHT WHEN IT IS NO LONGER NEED-

ED.

Keep wines that you plan to use for everyday drinking and

entertaining on the front half of the racks where labels are

completely visible. Place wines for aging or longer term

storing in the rear.

Pull-out Racks

The four (4) pull-out wine racks may be pulled out approxi-

mately seven and a half (7.5) inches to facilitate adding or

removing bottles. DO NOT lean on or press down heavily

on the wine shelves. Doing so may damage the shelves

and the wine bottles stored on them. Pull the wine racks

out gently and carefully to minimize unsettling your wine

collection. Avoid pulling out more than one rack at any time

to maintain stability.

Single Bottle Racks

The single level roll out racks allow you to easily view and

access your inventory without disturbing other bottles (see

Figure 18).

Figure 17

Figure 18

Front Bottles (Necks Facing Rear)

Rear Bottles (Necks Facing Front)

Figure 16

CAUTION

WARNING

DISCONNECT THE POWER CORD BEFORE AT-

TEMPTING LIGHT BULB REPLACEMENT. Failure

to do so may result in an electrical shock that could

severely injure you.

WARNING

Do NOT under any circumstance use a light bulb that

exceeds 25 watts!

Light bulb replacement

CARE AND CLEANING

Front Grille

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

The wine cellar uses one, 25 watt incandescent light bulb to

illuminate the interior of the wine cellar. The light bulb is a

very reliable electrical component, but should it not function

properly, please call the dealer where you purchased your

wine cellar from for a replacement light bulb. Use only an

original equipment light bulb from your dealer or Marvel.

To replace the light bulb, disconnect power to the unit. Un-

screw the old light bulb located behind the display housing

at the top of the unit. Set the old light bulb aside. Screw

the new light bulb into place. Reconnect power to the unit.

Check to see if the light bulb operates properly to complete

the installation.

The light bulb is not covered by your warranty. A replace-

ment bulb can be obtained from your dealer or from Marvel.

ENERGY SAVING TIPS AND OBTAINING SERVICE

If Service is Required:

• If the product is within the rst year warranty period

please contact your dealer or call Marvel Customer

Service at 800.223.3900 for directions on how to obtain

warranty coverage in your area.

• If the product is outside the rst year warranty period,

Marvel Customer Service can provide recommenda-

tions of service centers in your area. A listing of autho-

rized service centers is also available at www.marvelre-

frigeration.com under the service and support section.

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "B" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service Number

Date Warranty Card Sent (Must

be within 10 days of purchase).

Table B

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

13. For wine storage products:

When serving temperatures are not required,

return the compartment(s) set temperature to the

ideal red and white wine long term storage tem-

perature of 13°C / 55°F.

• Never attempt to repair or perform maintenance on

the appliance until the main electrical power has been

disconnected. Turning the appliance control "OFF"

does not remove electrical power from the unit's wiring.

• Replace all parts and panels before operating.

WARNING

Electrocution Hazard

TROUBLESHOOTING

Before You Call for Service

If the appliance appears to be malfunctioning, read through

this manual rst. If the problem persists, check the trouble-

shooting guide below. Locate the problem in the guide and

refer to the cause and its remedy before calling for service.

The problem may be something very simple that can be

solved without a service call. However, it may be required

to contact your dealer or a qualied service technician.

Problem Possible Cause Remedy

Appliance not cold enough

(See “Set temperature" on page 10)

• Control set too warm

• Content temperature not stabi-

lized.

• Excessive usage or prolonged

door openings.

• Airow to front grille blocked.

• Door gasket not sealing properly.

• Adjust temperature colder. Al-

low 24 hours for temperature to

stabilize.

• Allow temperature to stabilize for

at least 24 hours.

• Airow must not be obstructed to

front grille. See “clearances” on

page 4.

• Replace door gasket.

Appliance too cold

(See “Set temperature” on page 10)

• Control set too cold

• Door gasket not sealing properly.

• Adjust temperature warmer.

Allow 24 hours for temperature to

stabilize.

• Replace door gasket.

No interior light. • Failed light bulb. • Replace light bulb, see page 13.

Light will not go out when door is

closed

• Display light is turned on. (Glass

door models only.

• Door not activating light switch.

• Failed light switch

• Turn off display light, shut door.

• Appliance not level, level appli-

ance, (See page 4, “leveling legs”)

• Contact a qualied service techni-

cian.

Noise or Vibration • Appliance not level

• Fan hitting tube obstruction.

• Level appliance, see “Leveling

Legs” on page 4.

• Contact a qualied service techni-

cian.

Appliance will not run. • Appliance turned off

• Power cord not plugged in.

• No power at outlet.

• Turn appliance on. See “Starting

your refrigerator” on page 10.

• Plug in power cord.

• Check house circuit.

CAUTION

In the unlikely event you lose cooling in your unit, do not

unplug the product from the electric supply, but do call

a qualied service technician immediately. It is possible

that the loss of cooling capacity is a result of excessive

frost build-up on the evaporator cooling coil. In this case,

removing power to the unit will result in the melting of this

excessive quantity of ice, which could generate melt water

that exceeds the capacity of the defrost drain system and

could result in water damage to your home. The end-user

will be ultimately responsible for any water damage caused

by prematurely turning the unit off without appropriately

managing the excess water run-off.

HOUSEHOLD PRODUCT WARRANTY

Marvel Refrigeration (Marvel) Limited Warranty

ONE YEAR LIMITED PARTS & LABOR WARRANTY

For one year from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that

proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects

are included in this warranty, with coverage limited to 60 days from the date of original purchase. All service provided by Marvel under the

above warranty must be performed by a Marvel factory authorized servicer, unless otherwise specied by Marvel. Service provided during

normal business hours.

TWO YEAR LIMITED PARTS & LABOR WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For two years from the date of original purchase, this warranty covers all parts and labor to repair or replace any part of the product that

proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects

are included in this warranty, with coverage limited to 60 days from the date of original purchase. All service provided by Marvel under the

above warranty must be performed by a Marvel factory authorized servicer, unless otherwise specied by Marvel. Service provided during

normal business hours.

AVAILABLE THIRD YEAR LIMITED WARRANTY (MARVEL PROFESSIONAL PRODUCTS)

For designated Marvel Professional product, Marvel offers a one year extension of the two year warranty coverage from the date of pur-

chase, free of charge. To take advantage of this third year warranty, you must register your product with Marvel within 60 days from the date

of purchase at marvelrefrigeration.com and provide proof of purchase.

LIMITED FIVE YEAR SEALED SYSTEM WARRANTY

For ve years from the date of original purchase, Marvel will repair or replace the following parts, labor not included, that prove to be defec-

tive in materials or workmanship: compressor, condenser, evaporator, drier, and all connecting tubing. All service provided by Marvel under

the above warranty must be performed by a Marvel factory authorized servicer, unless otherwise specied by Marvel. Service provided

during normal business hours.

WARRANTY TERMS

These warranties apply only to products installed in any one of the fty states of the United States, the District of Columbia, or the ten

provinces of Canada. The warranties do not cover any parts or labor to correct any defect caused by negligence, accident or improper use,

maintenance, installation, service, repair, acts of God, re, ood or other natural disasters. The product must be installed, operated, and

maintained in accordance with the Marvel User Guide.

The remedies described above for each warranty are the only ones that Marvel will provide, either under these warranties or under any

warranty arising by operation of law. Marvel will not be responsible for any consequential or incidental damages arising from the breach of

these warranties or any other warranty, whether express, implied, or statutory. Some states do not allow the exclusion or limitation of inci-

dental or consequential damages, so the above limitation or exclusion may not apply to you. These warranties give you specic legal rights,

and you may also have other rights which vary from state to state.

Any warranty that may be implied in connection with your purchase or use of the product, including any warranty of merchantability or any

warranty t for a particular purpose is limited to the duration of these warranties, and only extends to ve years in duration for the parts de-

scribed in the section related to the ve year limited warranty above. Some states do not allow limitations on how long an implied warranty

lasts, so the above limitations may not apply to you.

• The warranties only apply to the original purchaser and are non-transferable.

• These warranties cover products installed and used for normal residential use only.

• The warranties apply to units operated outside only if designed for outdoor use by model and serial number.

• Replacement water lters, light bulbs, and other consumable parts are not covered by these warranties.

• The start of Marvel’s obligation is limited to four years after the shipment date from Marvel.

• In-home instruction on how to use your product is not covered by these warranties.

• Food, beverage, and medicine loss are not covered by these warranties.

• If the product is located in an area where Marvel factory authorized service is not available, you may be responsible for a trip

charge or you may be required to bring the product to a Marvel factory authorized service location at your own cost and expense.

• Units purchased after use as oor displays, and/or certied reconditioned units, are covered by the limited one year warranty only

and no coverage is provided for cosmetic defects.

• Signal issues related to Wi-Fi connectivity are not covered by these warranties.

For parts and service assistance, or to nd Marvel factory authorized service near you, contact Marvel Refrigeration:

MarvelRefrigeration.com • [email protected] • +616.754.5601

1260 E. Van Deinse St., Greenville, MI 48838

Marvel Refrigeration

All specications and product designs subject to change without notice. Such revisions do not

entitle the buyer to corresponding changes, improvements, additions, replacements or compensa-

tion for previously purchased products.

www.marvelrefrigeration.com

1260 E. Van Deinse St.

Greenville MI 48838

800.223.3900

41014822-EN Rev E

1/14/20

Wine Cellars

Celliers

ML15WSG0**

ML24WSG0**

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

Note: Wine Cellars are designed exclusively for the

storage of wine. Wine Cellars cannot attain storage

temperatures suitable for fresh food storage.

Remarque : Les celliers sont conçues exclusivement

pour y garder des vins. Elles ne peuvent pas atteindre des

températures de conservation convenant à l’entreposage

d’aliments frais.

ATTENTION

REMARQUE

Importantes instructions de sécurité

Les avertissements et les instructions de sécurité qui ap-

paraissent dans ce guide n’ont pas la prétention de couvrir

toutes les conditions et situations possibles pouvant arriver.

Il faut faire preuve de bon sens, de précautions et de soins,

pour installer, utiliser ou entretenir cet appareil.

Reconnaissance des symboles,

des mots et des étiquettes

concernant la sécurité.

ATTENTION - Risques ou pratiques dangereuses

pouvant entraîner des blessures individuelles, des dégâts

matériels ou des dommages au produit.

REMARQUE - Information importante pour réaliser une

installation et une utilisation sans problèmes.

CONTENU

AVERTISSEMENT - Risque possible de décès ou

de blessure grave si vous ne suivez pas les instructions.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de malformations et

autres déciences de naissance.

AVERTISSEMENT

Avertissements de la proposition 65 de l'État de Californie

: Ce produit contient au moins un produit chimique connu par

l’État de Californie pour être à l’origine de cancers.

AVERTISSEMENT

Contenu :

Informations de sécurité.......................................................2

Déballage de votre appareil ..................................................3

Enregistrement de la garantie ......................................3

Installation de votre appareil ..............................................4

Dégagements par rapport à l’armoire .............................4

Mise à niveau de l’appareil .............................................4

Raccordement électrique.................................................5

Installation du dispositif anti-basculement..........................6

Dimensions du produit.......................................................8

Utilisation de votre commande électronique ....................10

Congurations de étagères .............................................11

Entretien et nettoyage ......................................................13

Conseils pour l’économie d’énergie ................................14

Obtention de service ........................................................14

Dépannage................................................................15

Garantie...........................................................................16

La page charge ...

Marvel 30WCM768 Mode d'emploi

Marque: Marvel

Modèle: 30WCM768

Catégorie: Boissons glacées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel 30WCM768 User guide

Marvel 30WCM768 Mode d'emploi

Marvel 30WCM768 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents