LG 35912 Le manuel du propriétaire

Marque: LG

Modèle: 35912

Taper: Le manuel du propriétaire

Owner's Manual

Manuel de l’usager

ROOM AIR CONDITIONER

CLIMATISEUR DE PIÈCE

Model, Modèle 35910, 35912

Distributed by Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

www.sears.ca

ENGLISH FRANÇAIS

TABLE OF CONTENTS

- 2 -- 2 -

TABLE OF CONTENTS

........................

WARRANTY

..............................................

SAFETY

.....................................................

Important Safety Instructions

......................

ELECTRICAL REQUIREMENTS

.......

INSTALLING THE POWER CORD

....

INSTALLATION

........................................

Installation Requirements

.........................

Installation

................................................

How to Install

............................................

Removal from Window

.................................

OPERATION

.............................................

How and Why

...........................................

Normal Sounds

........................................

Capacity and Running Time

.....................

Features

.................................................

Using the Air Conditioner

.......................

Display

...................................................

Remote Control

......................................

MAINTENANCE

.....................................

Air Filter Cleaning

...................................

Air Conditioner Cleaning

........................

How to Remove the Front Grille

..................

How to Replace the Front Grille

..................

TROUBLESHOOTING

.........................

Before Calling for Service

......................

FRANÇAIS

..............................................

MASTER PROTECTION

AGREEMENTS

......................................

SERVICE NUMBERS

............

Back Cover

WARRANTY

One Year Limited Warranty

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails

due to a defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to

arrange for free repair.

Five Year Limited Warranty on Sealed Refrigerant System

For five years from the date of purchase, when this product is installed, operated and maintained according to all supplied

instructions, the sealed refrigerant system will be repaired free of charge if it is defective in material or workmanship.

This warranty covers only defects in material and workmanship. Sears will NOT pay for:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

Customer’s sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest

period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not

all

ow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of implied warranties of

merchantability or fitness, so these exclusions or limitations may not apply to you.

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

All warranty coverage applies for only 90 days from the date of purchase if this product is ever used for other than private

family purposes.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to the all instructions suppl ied

with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

This warranty applies only while this appliance is used in the United States or Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SAFETY

- 3 -

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or

damage to your ROOM AIR CONDITIONER.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance. Read product labels for flammability and

other warnings.

PREVENT ACCIDENTS

To reduce the risk of fire, electrical shock, or injury

to persons when using your air conditioner, follow

basic precautions, including the following:

• Be sure the electrical service is adequate for the

model you have chosen.

• If the air conditioner is to be installed in a window,

you will probably want to clean both sides of the

glass first. If the window is a triple-track type with a

screen panel included, you may want to remove

the screen completely before installation.

• Be sure the air conditioner has been securely and

correctly installed according to the separate

installation instructions provided with this manual.

Save this manual and installation instructions for

possible future use in removing or reinstalling this

unit.

• Use gloves when handling the air conditioner.

Be careful to avoid cuts from sharp metal fins on

front and rear coils.

ELECTRICAL INFORMATION

The complete electrical rating of your new room air

conditioner is stated on the serial plate. Refer to the

rating when checking the electrical requirements.

• Be sure the air conditioner is properly grounded.

To minimize shock and fire hazards, proper

grounding is important. The power cord is

equipped with a three-prong grounding plug for

protection against shock hazards.

• Your air conditioner must be plugged into in a

properly grounded wall receptacle. If the wall

receptacle you intend to use is not adequately

grounded or protected by a time delay fuse or

circuit breaker, have a qualified electrician install

the proper receptacle.

• Do not run air conditioner with a protective

covering. This could result in mechanical damage

within the air conditioner.

• Do not use an extension cord or an adapter

plug.

ENERGY SAVING IDEAS

• The capacity of the room air conditioner must fit

the room size for efficient and satisfactory

operation.

• Install the room air conditioner on the shady side

of your home. A window that faces north is best

because it is shaded most of the day.

• Do not block air conditioner flow inside with blinds,

curtains, or furniture, or outside with shrubs,

enclosures, or other buildings.

• Close the floor and wall registers and the fireplace

damper so cool air does not escape up the

chimney or into the duct work.

• Keep blinds and drapes in other windows closed

during the sunniest part of the day.

• Clean the air filter as recommended in the

MAINTENANCE section of this manual.

• Proper insulation and weather stripping in your

home will help keep warm air out and cool air in.

• External house shading with trees, plants or

awnings will help reduce the air conditioner's work

load.

• Operate heat producing appliances such as

ranges, washers, dryers, and dishwashers during

the coolest part of the day.

3-prong

grounding

plug

Reset

Test

Ground

prong

Power

supply

cord

3-prong

grounding

type wall

receptacle

Avoid fire hazard or electric shock.

Do not use an extension cord or an adapter plug.

Do not remove any prong from the power cord.

ELECTRICAL REQUIREMENTS

INSTALLING THE POWER CORD

- 4 -

Fasten the stopper using 1 screw holes, and lead

out the power cord through slit "A".

Fasten the stopper using left screw hole, and rotate

properly to lead the power cord out through slit "B".

USING SLIT "A" USING SLIT "B"

You can choose between two methods below according to your window stool shape and preference.

Power cord

OBSERVE ALL LOCAL CODES AND ORDINANCES.

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE

THE POWER SUPPLY CORD GROUND PRONG.

ELECTRICAL GROUND IS REQUIRED ON THIS

APPLIANCE.

For 230/208 volt 60 Hz, AC only, 15A fused and

properly grounded electrical supply is required. A time

delay fuse or time delay circuit breaker is

recommended. Use a dedicated circuit, serving only

this appliance.

DO NOT USE AN EXTENSION CORD.

RECOMMENDED GROUNDING METHOD

For your personal safety, this appliance must be grounded.

This appliance has a power supply cord with a 3-prong

grounding plug. To minimize possible shock hazard, the

cord must be plugged into a mating grounding type wall

receptacle and grounded in accordance with the National

Electrical Code (ANSI/NFPA 70) latest edition and all local

codes and ordinances. If a mating wall receptacle is not

available, it is the personal responsibility and obligation of

the customer to have a properly grounded 3-prong wall

receptacle installed by a qualified electrician.

115V~ 230V~

Power cord may include a current interrupter

device. A test and reset button is provided on the

plug case. The device should be tested on a

periodic basis by first pressing the TEST button

and then the RESET button. If the TEST button

does not trip or if the RESET button will not stay

engaged, discontinue use of the air conditioner and

contact a qualified service technician.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Use Wall Receptacle Power Supply

Standard 125V,

3-wire grounding

receptacle rated

15A, 125V AC

Standard 250V,

3-wire grounding

receptacle rated

15A, 250V AC

Use 15 AMP. time

delay fuse or 15 AMP.

circuit breaker.

Use 20 AMP. time

delay fuse or 20 AMP.

circuit breaker.

Standard 250V,

3-wire grounding

receptacle rated

20A, 250V AC

NOTE: The shape may be different according to its model.

INSTALLATION

- 5 -

ENGLISH

INSTALLATION REQUIREMENTS

Your air conditioner will install into standard double hung

windows with actual clear opening widths of 27 to 39 inches

(686mm to 990mm) (FIG. 1).

Lower sash must open sufficiently to allow a clear

vertical opening of 16 inches (406mm). Side louvers

and the rear of the air conditioner must have clear

air space to allow enough airflow through the

condenser for heat removal. The rear of the unit

must be outdoors, not inside a building or garage.

ELECTRICAL SERVICE

Check your available electrical service. The power

supply available must be the same as that shown

on the unit nameplate

(found on right side of cabinet).

All models are equipped with a 3-prong service plug

to provide proper service and safe positive

grounding. Do not change plug in any way. Do not

use an adapter plug. If your present wall outlet does

not match your plug, call a qualified electrician to

make the necessary corrections.

SAVE CARTON and this OWNER'S MANUAL for

future reference. The carton is the best way to store

unit during winter or when not in use.

INSTALLATION HARDWARE

686mm to 990mm

406mm

Inner sill

Offset

Window

Sill

Exterior

Interior wall

Sash

FIG. 1

FIG. 2

To avoid risk of personal injury, property damage,

or product damage due to the weight of this

device and sharp edges that may be exposed:

• Air conditioners covered in this manual pose an

excessive weight hazard. Two or more people

are needed to move and install the unit.

To prevent injury or strain, use proper lifting and

carrying techniques when moving unit.

• Carefully inspect location where air conditioner

will be installed. Be sure it will support the

weight of the unit over an extended period of

time.

• Handle air conditioner with care. Wear

protective gloves whenever lifting or carrying the

unit. AVOID the sharp metal fins of front and

rear coils.

• Make sure air conditioner does not fall during

installation.

CAUTION

E F G H I

B C D

REQUIRED TOOLS:

• Tight Fitting gloves

• Standard screwdriver

• Phillips screwdriver

• Pliers

• Sharp knife

• 3/8-inch open end wrench or adjustable wrench

• 1/4-inch hex socket and ratchet

• Tape measure

• Electric drill

• 1/4-inch drill bit

ITEM NAME OF PARTS Q'TY

A SIDE CURTAIN 2

B SILL SUPPORT 2

C BOLT 2

D LOCK NUT 2

E SCREW: 25/64" 13

F SCREW: 5/8" 3

G SCREW: 5/8" 5

H FOAM STRIP 1

I FOAM SEAL 1

J L BRACKET 1

INSTALLATION

- 6 -

INSTALLATION

Pick a location which will allow you to blow the cold

air into the area you want. Windows used for

installation must be strong enough to support the

weight of the air conditioner. Good installation with

special attention to the proper position of the unit

will lessen the chance that service will be needed.

When cooling more than one room, installation

location is very important. To cool your rooms, cold

air must be blown from the air conditioner in a

straight path.

HOW TO INSTALL

If the air conditioner is blocked by a storm

window frame, see step 19 on page 8 before

beginning to install.

Remove the screws which fasten the cabinet at

both sides and at the back. Save side screws.

Discard back screws.

Slide the unit out of the cabinet by gripping the

base pan handle and pull forward while bracing the

cabinet.

Cut the FOAM SEAL (ITEM I) to fit the

underside of the window sash. Peel off the backing

and attach the FOAM SEAL as shown in Fig. 5.

Insert the side curtain (ITEM A) into the upper

guide and lower guide of the air conditioner. Fasten

the curtains to the unit with screws (ITEM E).

Open the window. Mark a line on center of the

window inner sill.

Carefully place the cabinet on the window inner sill

and align the center of cabinet front with the center

line marked in the window inner sill.

Pull the bottom window sash down behind the

upper guide until they meet.

NOTE: Do not pull the window sash down so tightly

that the movement of side curtain is restricted.

Loosely assemble the sill supports using the

parts in FIG. 9.

FIG. 3

ITEM I

Sash

ITEM E

Upper guide

Lower guide

FIG. 4

FIG. 5

Upper guide

Window sill

Window sash Upper guide

Foam

seal

Cabinet

Side curtain

FIG. 7

FIG. 8

INDOOR OUTDOOR

ITEM C

ITEM D

ITEM B

FIG. 9

FIG. 6

ENGLISH

- 7 -

INSTALLATION

Select the position that will place the sill supports

near the outermost point on sill (FIG. 10).

Attach the sill supports to the cabinet track hole

closest to the selected position using screw (ITEM E).

Place the sill supports with the cabinet on the

window sill's selected position.

The cabinet should be installed with a very

slight tilt (about 1/4") downward toward the outside

(FIG. 11).

Adjust the bolts and the nuts of sill supports to level

the cabinet.

Attach the cabinet to the inner sill by driving the

screws (ITEM F) through the Lower Guide into the

window inner sill (FIG. 12).

Pull each side curtain fully to each side of

window opening.

Attach each side curtain to the window sash using

screws (ITEM G). (FIG. 13)

Attach the L BRACKET (ITEM J) with screw

(ITEM G). (FIG. 14)

DRAINAGE

Be sure to insert the drain pipe into base pan before

installation.

The air conditioner must be installed with a slight tilt

(1/4") downward to the outside for proper drainage of

excess condensed water through the drain pipe.

(FIG. 15)

Slide the chassis into the cabinet. (FIG. 16)

CAUTION: For security purposes, reinstall side

screws you removed in step 1.

Cut the foam strip (ITEM H) to the proper length

and insert between the upper window sash and the

lower window sash. (FIG. 17)

The vent control handle must be straightened

before the decorative front is attached.

Pull out part

to align with part .

Part

FIG. 18

Sash

Track

ITEM F

ITEM B

Lower Guide

FIG. 12

ABOUT "

ITEM B

Screw

Power

Cord

FIG. 11

ITEM G

ITEM J

BASE PAN REAR

DRAIN PIPE

BASE PAN BOTTOM

FIG. 13

FIG. 15

FIG. 14

INDOOR OUTDOOR

ABOUT

Cabinet

ITEM E

Lower guide

FIG. 10

FIG. 16

ITEM H

FIG. 17

INSTALLATION

- 8 -

FRONT INSTALLATION

Install the front grille(packed separately) onto the

cabinet as follows:

• Hook upper tabs of front grille into slots on the

cabinet top. (FIG. 19)

• Push front grille's tips towards the cabinet in order

to snap side tabs into the cabinet. (FIG. 19)

• Open the inlet grille. (FIG. 20)

• Install the screw (ITEM E) through the front grille.

(FIG. 20)

• Close inlet grille. (FIG. 21)

IF AIR CONDITIONER IS BLOCKED BY

STORM WINDOW FRAME

•

If storm window presents interference, fasten a 2"

wide wood strip to the inner window sill across the full

width of the sill. The wood strip should be thick

enough to raise the height of the window sill so that

the unit can be installed without interference from the

the storm window frame. See FIG. 22.

Top of wood strip should be approximately 3/4"

higher than the storm window frame to help

condensation to drain properly to the outside.

•

Install a second wood strip (approximately 6" long by

" wide and same thickness as first strip) in the

center of the outer sill flush against the back of the

inner sill. Screw the L brackets into this strip.

This will raise the L bracket as shown in FIG. 22.

REMOVAL FROM WINDOW

• Turn off and unplug the air conditioner.

• Remove the front grille. See HOW TO REMOVE THE

FRONT GRILLE. Refer to page 13.

• Unscrew the side screws that you installed in Step 15.

• Slide the air conditioner out of the cabinet.

BE CAREFUL NOT TO DROP IT. Hold onto it firmly the

whole way sliding it out. Once removed, set it safety out

of the way.

• Remove the L bracket from window frame and the sash

seal from between the windows.

• Unscrew the side curtains from the window frame. Fold

them back to the sides of the cabinet.

• Remove screws attaching cabinet to inner sill. Be careful

not to let cabinet fall once screws are removed.

• Remove cabinet from window opening.

• Place air conditioner into cabinet. Reinstall side screws

and Front Grille.

• Place unit and all assembly hardware in air conditioner

shipping carton, and store in clean, dry place.

ITEM E

Inlet grille

FIG. 19

Front Installation

INNER

SILL

WOOD STRIP MOUNTED

ON TOP OF INNER SILL

WOOD STRIP

FOR

BRACKET

L BRACKET

3/4"

CLEARANCE

1 1/2" min.

(38mm)

STORM

WINDOW

FRAME

OUTSIDEINSIDE

OUTER

SILL

FIG. 22

FIG. 20

Front Installation

FIG. 21

• Air conditioners covered in this manual pose an

excessive weight hazard. Two or more people

are needed to move and install the unit.

To prevent injury or strain, use proper lifting and

carrying techniques when moving unit.

• When handling the air conditioner, be careful to

avoid cuts from sharp metal fins on front and

rear coils.

• Make sure air conditioner does not fall during

removal.

CAUTION

HOW AND WHY

Your room air conditioner provides the following

functions to make hot weather living more

comfortable:

• Cools and circulates room air.

• Lowers humidity by removing excess moisture.

• Filters out summertime dust, dirt, and some

airborne impurities.

The air conditioner performs these functions by

drawing room air through a filter which traps dust

and dirt particles. The air then passes over a

cooling coil which refrigerates the air and removes

excess moisture. The same air is then returned to

the room– cooler, drier, and cleaner. Moisture

removed from the room air is carried to the outside

and evaporated.

Your air conditioner is designed to be easy to

operate and to provide plenty of cooling power.

NORMAL SOUNDS

FIG. 23

Aside from the regular fan motor and compressor

sounds coming from your air conditioner, you will

once in a while hear a pinging sound. This is the

result of moisture being picked up from the air in the

room and thrown against the air conditioner's fan.

This is normal and should not be cause for concern.

Also, do not be alarmed if you hear a slight hissing

or gurgling sound coming from your air conditioner

after it is off. These are normal coolant noises.

CAPACITY AND RUNNING TIME

Proper unit size is important in deciding the desired

comfort for the area you want to cool. An

undersized unit will not have the capability to cool,

leaving the area uncomfortably warm. The proper

size is determined by the number of square feet in

the area to be cooled, indoor and outdoor

temperature and humidity.

Whenever the heat or humidity load is above normal

the air conditioner must run longer and more often

to keep the desired temperature you have selected,

Under heavy heat load conditions the air conditioner

may need to run constantly to keep the temperature

you want.

At times using the MED FAN setting to circulate the

room air may make it comfortable even though the

air is not being cooled. This will decrease your cost

of use.

Fan

You may hear air

movement from

the fan.

Condenser

You may hear droplets of water hitting

the condenser causing a pinging or

clicking sound.

Unit Vibration

The unit may vibrate

and make noise

because of poor wall

or window construction.

Compressor

The modern high efficiency

compressor may have a high

pitched hum or pulsating

noise that cycles on and off.

OPERATION

- 9 -

ENGLISH

FIG. 23

OPERATION

- 10 -

FEATURES USING THE AIR CONDITIONER

To reduce the risk of fire, electric

shock, or injury to persons, read the important

SAFETY instructions section before operating this

appliance

To begin operating the air conditioner after

installation, follow these steps:

1. Plug in the air conditioner. (To prevent electrical

hazards, do not use an extension cord or an

adapter plug.)

2. Set the exhaust vent to the CLOSE position.

3. Set the TEMP Control to the coolest setting.

4. Set the MODE control at the highest COOL level.

5. Adjust the louvers for comfortable air flow.

6. Once the room has cooled, adjust the TEMP and

Mode Control to the setting you find most

comfortable.

NOTE : If the air conditioner is turned off, wait 3

minutes before restarting. This allows pressure

inside the compressor to equalize. Failure to wait 3

minutes before restarting may cause inefficient

operation.

If you move the TEMP Control to a warmer, then

immediately back to a cooler setting, the unit will

shut off. Wait 3 minutes before restarting.

7141 15 2

6 4

12 10 13 16

1. Cabinet

2. Vertical Air

Direction Louvers

3. Horizontal Air

Direction Louvers

4. Inlet Grille

5. Air Filter

6. Front Grille

7. Control Board

8. Power Cord

9. Evaporator Coil

10. Condenser

11. Compressor

12. Base pan

13. Brace

14. Upper Guide

15. Curtain

16. Remote Control

VENT CONTROL

The Vent Control allows the air conditioner to

either recirculate inside air (CLOSE) or exhaust

air to the outside (OPEN). (FIG. 25)

• The CLOSE position is used when maximum

cooling is desired. It may also be used for air

recirculation without cooling when the air

conditioner is set in the FAN position.

• The OPEN position removes stale air from the

room and exhausts it to the outside. Fresh air is

drawn into the room through your home's

normal air passages.

• The OPEN or CLOSE position can be used with

any fan selection.

PULL OPEN / PUSH CLOSE

FIG. 24

FIG. 25

OPERATION

- 11 -

ENGLISH

DISPLAY

REMOTE CONTROL SIGNAL

RECEIVER

POWER

TEMPERATURE SETTING

FAN SPEED

TIMER OPERATION

The timer can be used to either turn on or turn off the air

conditioner:

- Timer function for turning ON the air conditioner:

• With the POWER off, press the timer button to the number of hours when you want

• The air conditioner to come on. If it is 7 am and you want the unit to come on at 9 am

• Press the timer button twice so that a '2' shows up in the control panel window.

The unit will come on in 2 hours. You do not need to press the POWER button to turn on the unit. The timer function

will turn it on automatically in 2 hours.

- Timer function for turning OFF the air conditioner:

• This function will work only when the unit is already running and powered on.

Select the number of hours you want to shut off time. If it is 10 pm at night and you want the unit to shut off at 12 am

(midnight), press the timer button twice so that a '2' shows up in the control panel window. The unit will shut off in 2

hours.

• The timer function can be set in 1 hour increments up to 12 hours. That means you can set the unit to come on in 12

hours which is the maximum delay time, or you can enter the number of hours (maximum 12 hours) until the unit will

shut off.

• The delay timer functions to either turn on in a certain number of hours or turn off in a certain number of hours by

manually inputting the number of hours.

MODE

- Every time you push this button, it will shift among COOL, ENERGY SAVER and FAN.

- ENERGY SAVER:

• The fan stops when the compressor stops cooling.

Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is

needed.

• Every time you push this button, it advances the setting as follows:

{High → Low → Med → High}

• This button can automatically control the

temperature of the room.

The temperature can be set within a range

of 16°C to 30°C by increments of 1°C.

•

To turn the air conditioner ON, push the

button.

To turn the air conditioner OFF, push

the button again.

•

This button takes priority over any other

button.

•

When you first turn it on, the air conditioner is

on the High cool mode and the Temp. at 22°C.

AUTO RESTART

In failure of electric power, the unit runs as previous setting operation.

OPERATION

- 12 -

HORIZONTAL AIR DIRECTION CONTROL

The horizontal air direction is adjusted by moving the vertical

louvers right and left with your fingertips. (FIG. 26)

VERTICAL AIR DIRECTION CONTROL

The vertical air direction is adjusted by moving the horizontal

louvers up and down with your fingertips. (FIG. 27)

FIG. 26

FIG. 27

OPERATION

- 13 -

ENGLISH

REMOTE CONTROL

NOTE: The Remote Control will not operate properly if strong light shines on the sensor window of the Air

Conditioner or if there are obstacles between the Remote Control and the Air Conditioner.

Every time you push button, you will hear a beep from the Air Conditioner.

TEMPERATURE SETTING

• This button can automatically control the temperature of the room.

The temperature can be set within a range of 16°C to 30°C by increments of 1°C.

POWER

MODE

- Every time you push this button, it will shift among COOL, ENERGY SAVER and FAN.

ENERGY SAVER

• The fan stops when the compressor stops cooling.

Approximately every 3 minutes the fan will turn on and check the room air to determine if cooling is needed.

FAN SPEED

• Every time you push this button it advances the setting as follows:

(High → Low → Med → High)

Auto

Swing

POWER

TEMP

FAN SPEED

TIMER MODE

TIMER OPERATION

The timer can be used to either turn on or turn off the air conditioner:

- Timer function for turning ON the air conditioner:

• With the POWER off, press the timer button to the number of hours when you want

• The air conditioner to come on. If it is 7 am and you want the unit to come on at 9 am.

• Press the timer button twice so that a '2' shows up in the control panel window.

The unit will come on in 2 hours. You do not need to press the POWER button to turn

on the unit. The timer function will turn it on automatically in 2 hours.

- Timer function for turning OFF the air conditioner:

• This function will work only when the unit is already running and powered on.

Select the number of hours you want to shut off time. If it is 10 pm at night and you

want the unit to shut off at 12 am (midnight), press the timer button twice so that a '2'

shows up in the control panel window. The unit will shut off in 2 hours.

• The timer function can be set in 1 hour increments up to 12 hours. That means you

can set the unit to come on in 12 hours which is the maximum delay time, or you can

enter the number of hours (maximum 12 hours) until the unit will shut off.

• The delay timer functions to either turn on in a certain number of hours or turn off in a

certain number of hours by manually inputting the number of hours.

•

To turn the air conditioner ON, push the button. To turn the air conditioner OFF, push the

button again. This button takes priority over any other button.

When you first turn it on, the

air conditioner is on the High cool mode and the Temp. at

22°C.

OPERATION

- 14 -

1. Remove the cover from the back of the remote

controller.

• Open the cover according to the arrow direction on the

cover.

2. Insert two batteries.

• Be sure that the (+) and (-) directions are correct.

• Be sure that both batteries are new.

3. Re-attach the cover.

• Do not use rechargeable batteries.

Such batteries differ from standard dry cells in shape,

dimensions, and performance.

• Remove the batteries from the remote controller if the air

conditioner is not going to be used for an extended

length of time.

HOW TO INSERT BATTERIES INTO REMOTE CONTROL

ENGLISH

- 15 -

AIR FILTER CLEANING

The Air Filter will become dirty as it removes dust

from the inside air. It should be washed at least

every 2 weeks. If the Air Filter remains full of dust,

the air flow will decrease and the cooling capacity

will be reduced, possibly damaging the unit.

• Pull the inlet grille forward, grasping both tabs,

then pull out the air filter. (FIG. 28)

• Wash the Air Filter under the faucet with warm

water. Be sure to shake off all the water before

replacing the filter. (FIG.29)

AIR CONDITIONER CLEANING

Clean the front grille and inlet grille by wiping with a

cloth dampened in a mild detergent solution.

(FIG. 30)

The cabinet may be washed with mild soap or

detergent and lukewarm water, then polished with

liquid appliance wax.

To ensure continued peak efficiency, the condenser

coils (outdoor side at the unit) should be checked

periodically and cleaned if they become clogged

with soot or dirt from the atmosphere. Brush or

vacuum exterior coils to remove debris from fins.

HOW TO REMOVE THE FRONT

GRILLE

• Open the inlet grille downward.

• Remove the screw securing the Front Grille.

• Push the grille up from the bottom and pull the top

of the grille away from the case to lift the top tabs

out of their slots.

HOW TO REPLACE THE

FRONT GRILLE

Attach the front grille to the cabinet by inserting the

tabs on the grille into the slots on the front of the

cabinet. Push the grille in until it snaps into place.

Inlet Grille

Front Grille

MAINTENANCE

FIG. 28

FIG. 29

FIG. 31

FIG. 32

FIG. 30

TROUBLESHOOTING

- 16 -

BEFORE CALLING FOR SERVICE

Check the following list to be sure a service call is really necessary. A quick reference to this manual may

help you avoid an unneeded service call.

THE AIR CONDITIONER WILL NOT OPERATE.

Check if... Then...

AIR FROM UNIT DOES NOT FEEL COLD ENOUGH.

Check if... Then...

THE AIR CONDITIONER COOLING, BUT ROOM IS TOO WARM – ICE FORMING ON COOLING COIL BEHIND FRONT GRILLE.

Check if... Then...

THE AIR CONDITIONER COOLING, BUT ROOM IS TOO WARM .

Check if... Then...

THE AIR CONDITIONER TURNS ON AND OFF RAPIDLY.

Check if... Then...

NOISE WHEN UNIT IS COOLING.

Check if... Then...

WATER DRIPPING INSIDE ROOM WHEN UNIT IS COOLING.

Check if... Then...

WATER DRIPPING OUTSIDE WHEN UNIT IS COOLING.

Check if... Then...

Wall plug disconnected. Push plug firmly into wall outlet.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Power is OFF. Push the power button.

Unit was turned off and then on too quickly. Set unit off and wait 3 minutes before restarting.

TEMP Control set warmer than room temperature. Set TEMP Control to lower temperature.

FAN SPEED set at LOW. Push FAN SPEED button to set at HI.

TEMP Control set too warm. Set TEMP Control to lower temperature.

Room temperature below 70°F (21°C). Cooling may not occur until room temperature rises above 70°F (21°C)

Temperature sensing tube touching evaporator coil, Straighten tube away from evaporator coil.

located behind front grille.

Outdoor temperature below 70°F (21°C) To defrost the coil, set the MODE to FAN.

Air filter may be dirty. Clean air filter. Refer to Maintenance section of owner's manual.

TEMP Control set too cold for night-time cooling.

To defrost the coil, set

the MODE to FAN or "High Cool"

with the

TEMP control to higher

temperature

Dirty air filter – air restricted. Clean air filter. Refer to Maintenance section of owner's manual.

TEMP Control set too warm. Set TEMP Control to lower temperature.

Front of unit is blocked by drapes, blinds, furniture, etc. Clear blockage in front of unit.

Air distribution is restricted.

Doors, windows, registers, etc. open. Cold air escapes. Close doors, windows, registers, etc.

Unit recently turned on in hot room. A

llow additional time to remove stored heat from walls, ceiling, floor, and furniture.

Outside temperature is extremely hot.

Set FAN SPEED on HI to bring air past cooling coils faster.

Sound of fan hitting water from the moisture removal system.

This is normal when humidity is high. Close doors, windows, and registers.

Window vibration – poor installation. Refer to installation instructions or check with installer.

The air conditioner is improperly installed. Tilt air conditioner slightly to the outside to allow water drainage. Refer to

installation instructions or check with installer.

The unit is removing large quantities of moisture This is normal during excessively humid days.

from humid room.

The current interrupter device is triped Press the RESET button located on the power cord plug

If the RESET button will not stay engaged, discontinue use of the

air conditioner and contact a qualified service technician.

TABLE OF CONTENTS

- 17 -

AÇ

TABLE DES MATIÈRES

.....................

GARANTIE

..............................................

S CURIT

...............................................

Recommandations de sécurité

.................

EXIGENCES LECTRIQUES

..........

INSTALLING THE POWER CORD

INSTALLATION

....................................

Exigences de l’installation

......................

Installation

..............................................

Comment procéder à l’installation

..........

Retirer le climatiseur de la fenêtre

...............

FONCTIONNEMENT

............................

Comment et pourquoi

.............................

Sons normaux

........................................

Capacité et durée de fonctionnement

....

Caractéristiques

.....................................

Utilisation du climatiseur

........................

Affichage

................................................

Télécommande

......................................

MAINTENANCE

.....................................

Nettoyage du filtre à air

..........................

Nettoyage de l’appareil

..........................

Comment retirer la grille frontale

.................

Comment remettre en place la grille frontale

SOLUTION DE PROBLÈMES

..........

Avant d’appeler le service technique

.....

ACCORDS SUR LA PROTECTION

DU MASTER

..........................................

...................................

Au dos

NUM ROS DE SERVICE

TECHNIQUE

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

Garantie Limitée d’une Année

S i cet appareil est installé, utilisé et entretenu selon toutes les instructions fournies avec, en

cas de panne due à

des défauts de matériel ou de fabrication arrivées pendant la première

année suivant la date d’achat marquez

800

MY - HOME®

pour arranger des réparations

gratuites.

Cinq Années de Garantie Limitée pour le Système de Réfrigération Hermétique

Pendant les cinq années suivant la date d’achat, et s i cet appareil est installé, utilisé et entretenu selon toutes les

instructions fournies, le système de réfrigération hermétique sera réparé gratuitement en cas de dé faut matériel

ou de fabrication.

La couverture des garanties n’est valable que pour les 90 jours suivant la date d’achat si ce

produit est utilis é dans pour des raisons non familiales et privées.

Cette garantie ne recouvre que des d éfauts de matériel ou de fabrication.

Sears ne pr

end PAS en charge

1.Des éléments à usure sous un usage normal, y compris, entre autre, filtres, courroies,

ampoules et sacs.

2.Un technicien qualifié pour instruire l’usager sur l’installation, le fonctionnement ou l’entretien

corrects du produit.

3.U

n technicien qualifié pour nettoyer ou ent retenir ce produit.

4.D

es dégâts ou des pannes du produit s’il n’est pas install é, utilisé ou entretenu selon toutes les

instructions qui l’accompagnent.

5.D

es dégâts ou des pannes du pro duit découlant d’accidents, d’abus, d’usage incorrect ou

dans des buts différent

s à ce ux pour lesquel s il a été conçu.

6.D

es dégâts ou des pannes du produit dus à l’utilisation de détergents, de produits nettoyants ou chimiques, ou

d’ustensiles différents à ceux qui sont recommandés dans les instructions qui l’accompagne

nt.

7.D

es dégâts ou des pannes des pièces ou des systèmes issus de modifications non autorisées

à l’appareil.

Négation de garanties tacites ; limitation des recours

Le seul et unique remède accordé à l’usager avec cette garantie limitée sera la réparation ici

décrite. Les garanties

tacites, telles les garanties de conformité ou d’aptitude à des fins

spécifiques, sont limitées à une année où à la

période la plus courte permise par la loi. Sears ne sera pas responsable pour des dommages accidentels ou

conséquents. Certains états ou provinces ne permettent pas d’exclusions ou de limitations sur les dommages

accidentels ou conséquents, ou la limitation de la durée des garanties tacites de conformité ou d’aptitude à des fins

spécifiques, et il est donc possible que ces exclusions ou limitations ne soient pas

valables dans votre cas.

Cette garantie est seulement valable pour des appareils utilis

és aux Etats

-Unis ou au Canada.

Cette garantie vous accorde des droits particuliers,et il est possible que vous enayez d’autres

qui varient d’ état en état.

GARANTIE

SECURITE

- 18 -

IMPORTANTES RECOMMANDATIONS DE SECURITE

Les recommandations qui suivent vous indiqueront comment utiliser votre CLIMATISEUR DE PIÈCE sans

vous blesser ni endommager celui-ci.

CONCERNANT VOTRE SECURITE

Ne pas stocker ni utiliser de l’essence ni aucun

autre liquide inflammable ou produisant des

vapeurs inflammables à proximité de cet appareil ni

d’aucun autre. Lire les étiquettes concernant les

avertissements liés à l’inflammabilité ou à d’autres

dangers.

SUR LA PREVENTION D’ACCIDENTS

Pour réduire les risques d’incendie, de décharge

électrique, ou de blessures personnelles lors de

l’utilisation du climatiseur, respecter les précautions

de base, incluant celles qui suivent :

• Assurez-vous que le courant est adapté au

modèle que vous avez choisi.

• Si le climatiseur doit être installé sur une fenêtre,

vous voudrez sans doute d’abord nettoyer les

deux faces de la vitre. Si la fenêtre est composée

de 3 panneaux dont un panneau écran, ce dernier

doit être retiré avant l’installation.

• Assurez-vous que le climatiseur a été installé

correctement et dans le respect des

recommandations de sécurité en fonction des

instructions d’installation fournies dans ce manuel.

Conserver ce manuel et les instructions

d’installation pour vous y reporter dans le futur lors

du retrait et de la réinstallation de cet appareil.

• Utilisez des gants lors des manipulations de

l’appareil. Faites attention de ne pas vous couper

avec les extrémités métalliques des serpentins

avant et arrière.

SUR LES PRECAUTIONS ELECTRIQUES

L’évaluation électrique complète de votre nouveau

climatiseur figure sur la plaque de série. Vous

reporter à cette évaluation lors de la vérification des

exigences électriques.

• Assurez-vous que le climatiseur est correctement relié à

la terre. La connexion à la terre est importante afin de

réduire les risques de décharges électriques et

d’incendies. Le câble d’alimentation est équipé d’une

prise à trois fiches dont une reliée à la terre pour une

meilleure protection contre les risques de décharges.

• Votre climatiseur doit être correctement branché sur une

prise murale disposant d’une connexion à la terre. Si la

prise murale que vous voulez utiliser n’a pas de

connexion à la terre ou n’est pas protégée par un fusible

temporisé ou un disjoncteur, faites appel à un électricien

qualifié pour installer une prise murale conforme.

• Na pas utiliser le climatiseur avec une couverture

protectrice. Ceci pourrait provoquer un problème

mécanique à l’intérieur du climatiseur.

• Ne pas utiliser de prolongateur ou

d’adaptateur.

IDEES POUR ECONOMISER L’ENERGIE

• La capacité du climatiseur doit correspondre à la taille

de la pièce afin que son fonctionnement soit efficace et

satisfaisant.

• Installer le climatiseur à l’ombre. Une fenêtre orientée

vers le nord est le meilleur emplacement parce qu’il est

à l’ombre presque toute la journée.

• Ne pas bloquer la circulation de l’air, à l’intérieur par des

stores, des rideaux ou des meubles, et à l’extérieur par

des arbustes, des clôtures ou des constructions.

• Fermer les ouvertures du sol et des murs de même que

le conduit de la cheminée afin que l’air froid ne

s’échappe pas par ces différents conduits.

• Fermer les stores et les tentures des autres fenêtres

durant les moments les plus ensoleillés.

• Nettoyer le filtre à air comme indiqué dans la section

MAINTENANCE de ce manuel.

• Une isolation correcte et un nettoyage saisonnier de

votre maison permettront de maintenir l’air chaud à

l’extérieur et l’air froid à l’intérieur.

• Les arbres, les plantes ou les bannes extérieures faisant

de l’ombre à la maison faciliteront la mise en place du

travail du climatiseur.

• Faire fonctionner les appareils générant de la chaleur,

tels cuisinières, machines à laver, séchoirs et

lave-vaisselle durant le moment le plus frais de la

journée.

AVERTISSEMENT

Prise à

3 fiches

Remise

à zéro

Test

Prise de terre

Câble

d’alimentation

Prise murale

avec 3 entrées

AVERTISSEMENT

Pour éviter les risques d’incendie

ou de décharge électrique.

N’utiliser ni prolongateur ni adaptateur.

Ne retirer aucune fiche du câble d’alimentation.

AVERTISSEMENT

TABLE OF CONTENTS

- 19 -

FRANÇAIS

EXIGENCES ELECTRIQUES

INSTALLATION DU CÂBLE D’ALIMENTATION

Fixer le taquet à l’aide de la cavité prévue pour la vis et

faire sortir la câble d’alimentation par l’encoche ‘’A’’.

Fixer le taquet à l’aide de la cavité prévue pour la vis et

effectuer une rotation correcte pour permettre de faire sortir la

câble d’alimentation par l’encoche ‘’B’’.

UTILISATION DE L’ENCOCHE « A » UTILISATION DE L’ENCOCHE « B »

Vous pouvez choisir entre les deux méthodes ci-dessous en fonction de la forme du rebord de votre fenêtre et votre préférence.

Power cord

OBSERVER TOUS LES CODES ET ORDONNANCES

LOCAUX.

NE RETIRER SOUS AUCUN PRETEXTE LA FICHE DE

CONNEXION A LA TERRE DE LA PRISE DU CÂBLE

D’ALIMENTATION.

UNE PRISE DE TERRE EST EXIGEE SUR CET APPAREIL.

l est exigé un courant de

230/208V

60Hz, exclusivement

AC un fusible de 20A et une correcte connexion à la terre.

Il est recommandé un fusible temporisé ou un disjoncteur.

Utiliser un circuit particulier pour cet appareil.

NE PAS UTILISER DE PROLONGATEUR.

METHODE RECOMMANDEE DE CONNEXION A LA TERRE.

Pour votre sécurité personnelle, cet appareil doit être relié à la

terre. Cet appareil a un câble d’alimentation muni d’une prise à

3 fiches avec connexion à la terre. Afin de réduire au maximum

les risques de décharge, le câble doit être branché sur une

prise murale encastrée et reliée à la terre suivant la dernière

édition du Code Électrique National (ANSI/NFPA 70) et toutes

les ordonnances et codes locaux. Si vous ne disposez pas

d’une prise murale de ce type, c’est votre obligation et

responsabilité personnelle d’en faire installer une par un

électricien qualifié.

115V~ 230V~

Utiliser une prise Murale encastrée

125V standard,

boîtier de 3 entrées

de 15A, 125V AC.

NOTE: La forme peut différer suivant les modèles.

Le câble d’alimentation inclut un dispositif

interrupteur. Sur le boîtier de la prise il existe une

touche de test et une de remise à zéro. Le dispositif

doit être testé périodiquement en appuyant sur

TEST et ensuite sur RESET. Si la touche TEST ne

bouge pas ou si la touche RESET ne se maintient

pas engagée, interrompre l’usage de l’appareil et

contacter un électricien agréé

250V standard,

boîtier de 3 entrées

de 15A, 250 AC.

250V standard,

boîtier de 3 entrées

de 20A, 250V AC.

Utiliser un fusible

temporisé ou un

disjoncteur de 15 AMP.

Utiliser un fusible

temporisé ou un

disjoncteur de 20 AMP.

AVERTISSEMENT

Risque de décharge électrique

Brancher la prise sur une prise murale à 3 entrées

Ne pas retirer la fiche reliée à la terre

Ne pas utiliser d’adaptateur

Ne pas utiliser de prolongateur

Le non respect de ces instructions peut provoquer la mort,

un incendie ou une décharge électrique.

TABLE OF CONTENTS

- 20 -

INSTALLATION

CONDITIONS D’INSTALLATION

Le climatiseur doit être installé sur une fenêtre standard à

guillotine à deux panneaux ayant une ouverture d’une largeur

comprise entre 686 et 990mm (FIG. 1). Le châssis inférieur

doit ouvrir de manière à laisser une ouverture verticale de

406mm. Les parois latérales et la partie postérieure du

climatiseur doivent disposer d’un espace permettant la

circulation de l’air dans le condenseur afin d’éliminer la

chaleur. La partie postérieure de l’appareil doit donner sur

l’extérieur et non sur une autre pièce ou un garage.

COURANT ELECTRIQUE

Vérifier le courant disponible. Le courant disponible

fourni doit être le même que celui qui figure sur la

plaque nominative de l‘appareil (sur la gauche du

coffrage). Tous les modèles sont équipés d’une

prise à 3 fiches prévue pour fournir un service

adéquat et une connexion sure à la terre. Ne faire

aucune modification sur la prise. Ne pas utiliser

d’adaptateur. Si votre prise murale ne coïncide pas

avec la prise du câble, faites appel à un électricien

qualifié pour effectuer les corrections nécessaires.

CONSERVER L’EMBALLAGE et LE MANUEL DE

L’USAGER pour vous y reporter dans le futur.

L’emballage original est la meilleure manière de

ranger l’appareil en hiver ou quand il n’est pas

utilisé.

MATERIEL D’INSTALLATION

686 et 990mm

406mm

Seuil interieur

Decalage

Fenetre

Seuil

Exterieur

Mur interieur

Cadre

FIG. 1

FIG. 2

Pour éviter les risques de blessures, des dommages

personnels ou d’endommager l’appareil à cause de

son poids ou des angles pointus :

• Les climatiseurs couverts par ce manuel sont

généralement lourds. Deux personnes ou plus sont

nécessaires pour déplacer et installer un appareil.

Afin d’éviter de vous blesser ou d’être sous

pression, utiliser les méthodes correctes pour

soulever et transporter l’appareil.

• Inspecter soigneusement l’endroit dans lequel le

climatiseur sera installé. Assurer vous que cet

endroit pourra supporter le poids de l’appareil

pendant longtemps.

• Manipuler soigneusement le climatiseur. Utiliser

des gants de protection lorsque vous le soulevez

ou le déplacez. ÉVITER le contact avec les

extrémités métalliques des serpentins avant et

arrière.

PRÉCAUTION

E F G H I

B C D

OUTILS NÉCESSAIRES:

• Gants moulants

• Tournevis standard

• Tournevis Phillips

• Pince

• Couteau pointu

• Clé avec ouverture de 3/8 pouces ou clé réglable

• Prise hexagonale de 1/4 pouces et rochet

• Centimètre

• Perçeuse électrique

• Mèche de 1/4 de pouce

NOM DES PIÈCES

ET QUANTITÉS

PANNEAUX COULISSANTS

SUPPORT POUR REBORD

C BOULON 2

D ÉCROU DE SERRAGE 2

E VIS 25/64’’ 13

F VIS 5/8’’ 3

G VIS 5/8’’ 5

H BANDE DE MOUSSE 1

SCELLAGE DE MOUSSE

J ÉQUERRE L 1

La page charge ...

LG 35912 Le manuel du propriétaire

Marque: LG

Modèle: 35912

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: LG 35912 Owner's manual

LG 35912 Le manuel du propriétaire

LG 35912 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents