Blade OZONE RTF BLH9700 Manuel utilisateur

Catégorie
Jouets télécommandés
Taper
Manuel utilisateur
RTF
READY-TO-FLY
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni
2
EN
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before
operating. Failure to operate the product correctly can result in damage to the product, personal property and
cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic
mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage
to the product or other property. This product is not intended for use by children without direct adult supervision. Do
not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon
Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow
all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid
damage or serious injury.
The following terms are used throughout the product literature to indicate various levels of potential harm when
operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,
and serious injury OR create a high probability of superfi cial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a
possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no
possibility of injury.
Always keep a safe distance in all directions around
your model to avoid collisions or injury. This model is
controlled by a radio signal subject to interference from
many sources outside your control. Interference can
cause momentary loss of control.
Always operate your model in open spaces away from
full-size vehicles, traffi c and people.
Always carefully follow the directions and warnings for
this and any optional support equipment
(chargers, rechargeable battery packs, etc.).
Always keep all chemicals, small parts and anything
electrical out of the reach of children.
Always avoid water exposure to all equipment not
specifi cally designed and protected for this purpose.
Moisture causes damage to electronics.
Never place any portion of the model in your mouth as it
could cause serious injury or even death.
Never operate your model with low transmitter
batteries.
Always keep aircraft in sight and under control.
Always move the throttle fully down at rotor strike.
Always use fully charged batteries.
Always keep transmitter powered on while aircraft is
powered.
Always remove batteries before disassembly
Always keep moving parts clean.
Always keep parts dry.
Always let parts cool after use before touching.
Always remove batteries after use.
Never operate aircraft with damaged wiring.
Never touch moving parts.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon
Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
Safety Precautions and Warnings
Age Recommendation: Not for children under 14 years. This is not a toy.
3
EN
Box Contents
Components
Specifi cations
• Blade
®
Ozone
• 3.7V 25C 500mAh 1S Li-Po Battery (RTF Only)
• 1S USB Li-Po Charger (RTF Only)
• MLP4DSM Transmitter (RTF Only)
• 4 AA Batteries (RTF Only)
Table of Contents
Length
6.78 in (172mm)
Height
2.20 in (56mm)
Propeller Diameter
2.56 in (65mm)
Flying Weight
2.65 oz (75 g)
RTF BLH9700 BNF BLH9750
Airframe – Blade
®
Ozone
(BLH9700) Included Included
Motors – 8.53mm Brushed, (BLH9709, CW), (BLH9710, CCW) Installed Installed
On-board Electronics – Main control board, SAFE
®
(BLH9706) Installed Installed
Battery – 500mAh 1S 3.7V 25C Li-Po (EFLB5001S25UM) Included Required
Charger – 1S USB Li-Po Charger, 500 mAh, High-current UMX (EFLC1013) Included Required
Transmitter – MLP4DSM 2.4 GHz, 4 CH Transmitter, BCMX2 (EFLH1064/B) Included Required
To register your product online,visit www.bladehelis.com
Components ....................................................................3
Specifi cations ..................................................................3
Box Contents ...................................................................3
First Flight Preparation .....................................................4
Flying Checklist ...............................................................4
Charging Warnings...........................................................4
Battery Charging ..............................................................5
Installing the Transmitter Batteries (RTF) ..........................5
Installing the Flight Battery ..............................................5
Transmitter and Receiver Binding .....................................6
SAFE Technology .............................................................7
Transmitter Control ..........................................................7
Flight Mode Selection ......................................................8
LED Codes .......................................................................8
Understanding the Primary Flight Controls .......................9
Flying the Ozone ............................................................10
Post-Flight Inspection and Maintenance Checklist ..........10
Troubleshooting Guide ...................................................10
Exploded View ...............................................................12
Parts Listings .................................................................12
Limited Warranty ...........................................................13
Warranty and Service Contact Information .....................14
FCC Information .............................................................14
IC Information ...............................................................14
Compliance Information for the European Union .............14
4
EN
The Battery Charger (EFLC1013) included with your
quadcopter has been designed to safely charge the Li-Po
battery.
CAUTION: All instructions and warnings must be
followed exactly. Mishandling of Li-Po batteries can
result in a fi re, personal injury and/or property damage.
By handling, charging or using the included Li-Po battery,
you assume all risks associated with lithium batteries.
If at any time the battery begins to balloon or swell,
discontinue use immediately. If charging or discharging,
discontinue and disconnect. Continuing to use, charge or
discharge a battery that is ballooning or swelling can result
in fi re.
Always store the battery at room temperature in a dry area
for best results.
Always transport or temporarily store the battery in a tem-
perature range of 40–120º F (5–49° C). Do not store battery
or model in a car or direct sunlight. If stored in a hot car, the
battery can be damaged or even catch fi re.
Always charge batteries away from fl ammable materials.
Always inspect the battery before charging.
Always disconnect the battery after charging, and let the
charger cool between charges.
Always constantly monitor the temperature of the battery
pack while charging.
ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE
LI-PO BATTERIES. Failure to charge the battery with a
compatible charger may cause a fi re resulting in personal
injury and/or property damage.
Never discharge Li-Po cells to below 3V under load.
Never cover warning labels with hook and loop strips.
Never leave charging batteries unattended.
Never charge batteries outside recommended levels.
Never charge damaged batteries.
Never attempt to dismantle or alter the charger.
Never allow minors to charge battery packs.
Never charge batteries in extremely hot or cold places
(recommended between 40–120° F or 549° C) or place in
direct sunlight.
Charging Warnings
Battery Charging
NOTICE: Charge only batteries that are cool to the touch
and are not damaged. Look at the battery to make sure it
is not damaged e.g., swollen, bent, broken or punctured.
1. Insert the charger into a USB port.
2. Properly connect the battery to the charger lead.
3. Always disconnect the fl ight battery from the charger immediately upon completion of charging.
CAUTION: Only use chargers specifi cally designed to charge the included Li-Po battery. Failure to do so could result
in fi re, causing injury or property damage.
CAUTION: Never exceed the recommended charge rate.
LED Indications
When you make the connection successfully, the LED on the charger turns solid red, indicating charging has begun.
Charging a fully discharged (not over-discharged) 500mAh battery takes approximately 60 minutes. The light goes out
when the charge is complete.
CHARGING (Solid Red)
MAX CHARGE (OFF)
CAUTION: Once charging is complete, immediately remove the battery. Never leave a battery connected to the
charger.
First Flight Preparation
Remove and inspect contents
Begin charging the fl ight battery
Install the fl ight battery in the quadcopter
(once it has been fully charged)
Program your computer transmitter (BNF only)
Bind your transmitter (BNF only)
Familiarize yourself with the controls
Find a suitable area for fl ying
Flying Checklist
Always turn the transmitter on fi rst
Plug the fl ight battery into the lead from the 5-in-1
control unit
Allow the 5-in-1 control unit to initialize and arm
properly
Fly the model
Land the model
Unplug the fl ight battery from the 5-in-1 control unit
Always turn the transmitter off last
5
EN
Installing the Transmitter Batteries (RTF)
Replace the transmitter batteries when the power LED fl ashes and the
transmitter beeps.
1. Lower the throttle to the lowest setting. For BNF aircraft, engage throttle hold if your transmitter is so equipped.
2. Power on the transmitter.
3. Install the battery by sliding it into the battery mounting slot below the control unit. Slide the battery into the slots
with the label facing upward so that the battery key molded into the battery end-cap comes in contact with
the key on the battery slot.
4. Connect the battery cable to the control unit.
5. Place the quadcopter on a fl at surface and leave the aircraft still until the LED on the control unit indicates one of the
following fl ight modes:
Solid blue: Stability mode, switch position 1
Solid red: Agility mode, switch position 2
CAUTION: Always disconnect the Li-Po battery from the aircraft when not fl ying to avoid over-discharging the
battery. Batteries discharged to a voltage lower than the lowest approved voltage may become damaged,
resulting in loss of performance and potential fi re when batteries are charged.
Installing the Flight Battery
12
ansmitter is so equipped
3
4
6
EN
CAUTION: When using a Futaba
®
transmitter with a SpektrumDSM2
®
/DSMX
®
module, you must reverse the
throttle channel and re-bind. Refer to your Spektrum module manual for binding and failsafe instructions.
Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.
MLP4DSM Binding Procedure
1. Disconnect the fl ight battery from the quadcopter.
2. Center all trims on your transmitter.
3. Power off the transmitter and move the throttle stick to the down/off position.
4. Connect the fl ight battery in the quadcopter. The LED on the control unit fl ashes after 5 seconds.
5. When the blue light is fl ashing, push in and hold down the left stick* while powering on the transmitter
(you will hear a ‘click’).
6. Release the left stick. The transmitter will beep and the power LED will blink.
7. The quadcopter is bound when all of the LEDs on the aircraft turn solid.
8. Disconnect the fl ight battery and power the transmitter off.
* The trigger switch may also be used for the binding procedure.
If you encounter problems, obey binding instructions and refer to the troubleshooting guide for other instructions.
If needed, contact the appropriate Horizon Product Support offi ce. For a list of compatible DSM
®
transmitters, please
visit www.bindnfl y.com.
RTF
Your RTF transmitter comes prebound to the model. If you need to re-bind, follow the directions below.
Transmitter and Receiver Binding
If you are using a computer transmitter, set the model type to “Acro” or “Airplane” mode. In the channel input menu, set
channel 6 (Aux1) to a momentary switch such as the bind button ( I) and channel 5 (Gear) to a 3-position switch (switch
B). In the Servo Setup menu, reverse channel 6 (Aux1).
Bind the quadcopter to your transmitter following the Transmitter and Receiver Binding directions below.
General Binding Procedure
1. Disconnect the fl ight battery from the quadcopter.
2. Center all trims on your transmitter.
3. Power off the transmitter and fully lower the throttle.
4. Connect the fl ight battery in the quadcopter. All of the LEDs on the aircraft will fl ash rapidly, indicating the aircraft has
entered bind mode.
5. Put the transmitter into bind mode while powering on the transmitter.
6. Release the bind button/switch after 2–3 seconds. The quadcopter is bound when all of the LEDs on the aircraft
turn solid.
7. Disconnect the fl ight battery and power the transmitter off.
7
EN
RTF
Transmitter Control
Revolutionary SAFE
®
(Sensor Assisted Flight Envelope) technology uses an innovative combination of multi-axis sensors and
software that allows model aircraft to know its position relative to the horizon. This spatial awareness is utilized to create a
controlled fl ight envelope the aircraft can use to maintain a safe region of bank and pitch angles so you can fl y more safely.
Far beyond stability, this level of protection offers multiple modes so the pilot can choose to develop his or her skills with a
greater degree of security and fl ight control that always feels crisp and responsive.
SAFE technology delivers:
• Flight envelope protection you can enable at the fl ip of a switch.
• Multiple modes let you adapt SAFE technology to your skill level instantly.
Best of all, sophisticated SAFE technology doesn’t require any work to enjoy. Every aircraft with SAFE installed is ready to use
and optimized to offer the best possible fl ight experience.
FlySAFERC.com
Technology
®
ABCDE F
Mode
1
Aileron (Left/Right)
Throttle (Up/Down)
Throttle
Trim
Aileron
Trim
Rudder
Trim
Elevator
Trim
Rudder (Left/Right)
Elevator (Up/Down)
Mode
2
Aileron (Left/Right)
Elevator (Up/Down)
Elevator
Trim
Aileron
Trim
Rudder
Trim
Throttle
Trim
Rudder (Left/Right)
Throttle (Up/Down)
Flight mode
selection
• Bind
• Long press:
Arm/Disarm
D
E
F
Power LED indicator
C
B
A
On/Off Switch
When pressed down, trim buttons make a sound that increases or decreases in pitch at each pressing. The middle or
neutral trim position is heard as a middle tone in the pitch range of the sounds. The end of the control range is sounded
by a series of beeps.
Fl
se
8
EN
RTF
Change fl ight modes by pushing down on the right stick. Ensure the fl ight mode switch is in the
desired position before fl ying.
• In Stability mode (switch position 1), the controls provide a minimum bank angle. This mode
is shown by the fl ight control LEDs on the quadcopter glowing solid blue.
• Agility mode (switch position 2) is shown by the fl ight control LEDs on the quadcopter
glowing solid red.
If you purchased a BNF Ozone
quadcopter, the channel 5 switch on your transmitter will select fl ight modes.
Flight Mode Selection
LED Codes
Equipment LED Color LED Status Operation
Quadcopter:
Flight control LEDs on
the control board
Blue
Solid Stability mode, switch position 1
Blinking Loss of RF / Transmitter OFF
Red
Solid Agility mode, switch position 2
Blinking Low Battery
White Blinking Disarmed, Ready
Quadcopter:
Outer motor pod LEDs
White (Front)
Red (Rear)
Slowly Dim and Brighten In relation to throttle input
9
EN
Elevator
ForwardElevator down
Elevator up
Backward
Left Side View Left Side View
Rudder
Rudder left
Rudder right
Nose Yaws Right
Nose Yaws Left
Understanding the Primary Flight Controls
If you are not familiar with the controls of your Ozone
quadcopter, take a few minutes to familiarize yourself with them
before attempting your fi rst fl ight.
Throttle
Throttle down
Throttle up
Left Side View Left Side View
Descend
Climb
Aileron
Aileron left
Left
Aileron right
Right
Rear ViewRear View
10
EN
Post-Flight Inspection and Maintenance Checklist
Cleaning
Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or
a dry, lint-free cloth.
Motors Replace the motor when the model will not fl y steady or veers off when doing a climb out.
Wiring Make sure the wiring does not block moving parts. Replace damaged wiring and loose connectors.
Fasteners
Make sure there are no loose screws, other fasteners or connectors. Do not over-tighten metal
screws in plastic parts. Tighten screws so the parts are mated together, then turn the screw only
1/8th of a turn more.
Propellers
Make sure there is no damage to the propellers or other parts that move at high speed. Damage to
these parts includes cracks, burrs, chips or scratches. Replace damaged parts before fl ying.
Troubleshooting Guide
Problem Possible Cause Solution
Quadcopter control response is
inconsistent or requires extra trim
to neutralize movement.
Aircraft not initialized on a level surface.
Disconnect the fl ight battery, center the control
trim and re-initialize the quadcopter.
Battery not correctly placed in
battery slot.
Adjust battery position so quadcopter balances
in the center of the frame.
Quadcopter will not respond to
throttle.
Throttle too high and/or throttle trim is
too high.
Reset controls with the throttle stick
and throttle trim at the lowest setting.
Quadcopter moved during initialization.
Disconnect the flight battery and re-initialize
the quadcopter while keeping the quadcopter
from moving.
Throttle channel is reversed.
Disconnect fl ight battery, reverse the throttle
channel on the transmitter,
recconnect fl ight battery.
Quadcopter does not function
and smells burnt after connecting
the fl ight battery.
Flight battery connected with the wrong
polarity.
Replace the 5-in-1 board. Connect the fl ight
battery noting proper polarity.
Quadcopter has reduced fl ight
time or is underpowered.
Flight battery charge is low. Completely recharge the fl ight battery.
Inadequate power to fl ight battery charger.
Use a different USB power source for the
charger.
Flight battery is damaged.
Replace the fl ight battery and follow the fl ight
battery instructions.
Flight conditions might be too cold.
Make sure the battery is warm (room
temperature) before use.
Takeo
Increase the throttle until the model is approximately 2 ft. (600mm) off the ground and check the trim so the model
ies as desired. Once the trim is adjusted, begin fl ying the model.
Typical fl ight times for the included battery range from 5 to 10 minutes.
Low Voltage Cuto (LVC)
LVC decreases the power to the motors when the battery voltage gets low. When the motor power decreases and the
front and rear FC LEDs fl ash red, land the aircraft immediately and recharge the fl ight battery.
LVC does not prevent the battery from over-discharge during storage.
NOTICE: Repeated fl ying to LVC will damage the battery.
Landing
To land, slowly decrease the throttle while in a low-level hover. After landing, hold the arm/disarm switch until the
motors have stopped, then remove the battery. Fully charge your battery before storing it. During storage, make sure the
battery charge does not fall below 3V per cell.
Flying the Ozone
11
EN
Problem Possible Cause Solution
LED on receiver fl ashes rapidly
and aircraft will not respond to
transmitter (during binding).
Transmitter too near aircraft during bind-
ing process.
Power off the transmitter. Move the transmitter
a larger distance from the aircraft. Disconnect
and reconnect the fl ight battery to the aircraft.
Follow the binding instructions.
Bind switch or button was not held while
transmitter was powered on.
Power off transmitter and repeat bind process.
Aircraft or transmitter is too close to large
metal object, wireless source or another
transmitter.
Move aircraft and transmitter to another
location and attempt binding again.
LED on the receiver fl ashes rap-
idly and the quadcopter will not
respond to the transmitter (after
binding).
Less than a 5-second wait between fi rst
powering on the transmitter and connect-
ing the fl ight battery to the quadcopter.
Leave the transmitter powered on. Disconnect
and reconnect the fl ight battery to the
quadcopter.
The quadcopter is bound to a different
model memory (ModelMatch™ transmit-
ters only).
Select the correct model memory on the
transmitter. Disconnect and reconnect the fl ight
battery to the quadcopter.
Flight battery or transmitter battery charge
is too low.
Replace or recharge batteries.
Aircraft or transmitter is too close to
large metal object, wireless source or
another transmitter.
Move aircraft and transmitter to another
location and attempt connecting again.
Crashes immediately upon lift-off
Propellers in wrong locations or
incorrect fl ight mode selected.
Ensure propeller direction and motor
direction are correct.
12
EN
Exploded View
Parts Listings
Part # Description
1 BLH9706 Main control board: Ozone
2 BLH9707 Left boom set (2)
3 BLH9708 Right boom set (2)
4 BLH9710 Counterclockwise motor
5 BLH9709 Clockwise motor
6 BLH9702 Inner frame
7 BLH9704 Canopy
8 BLH9703 Complete propeller set (4)
9 BLH9705 Motor mount cover (semi-transp)
10 BLH9712 Landing skids
11 BLH7521 Propeller, CCW rotation, black (2)
Part # Description
12 BLH7520 Propeller, CW rotation, black, (2)
13 BLH7513 Propeller shaft, carbon
14 BLH3506 Main gear: BMSR, mCP S/X
15 BLH3515
Main shaft bearing, 3x6x2mm (2):
BMCX/2/MSR, MH-35, mCP X
16
EFLB5001S25UM
3.7V 500mAh 1S 25C LiPo, High
current UMX connector
17 EFLC1013
1S USB LiPo charger, 500 mAh, High
current UMX connector
18 EFLH1064/B
Blade MLP4DSM 4CH transmitter,
2.4 GHz: BMCX2, 120SR
14
15
15
LED
13
17
18
10
8
12
8
12
8
11
8
11
1
6
2
3
9
16
4
4
5
5
7
13
EN
Limited Warranty
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser
that the product purchased (the "Product") will be free from
defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic
damage, (ii) damage due to acts of God, accident, misuse,
abuse, negligence, commercial use, or due to improper use,
installation, operation or maintenance, (iii) modification of or to
any part of the Product, (iv) attempted service by anyone other
than a Horizon Hobby authorized service center, (v) Product not
purchased from an authorized Horizon dealer, or (vi) Product not
compliant with applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES
THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT
WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive
remedy shall be that Horizon will, at its option, either (i)
service, or (ii) replace, any Product determined by Horizon to
be defective. Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S
SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY
OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Further, in no event shall the liability of Horizon exceed the
individual price of the Product on which liability is asserted.
As Horizon has no control over use, setup, final assembly,
modification or misuse, no liability shall be assumed nor
accepted for any resulting damage or injury. By the act of use,
setup or assembly, the user accepts all resulting liability. If you
as the purchaser or user are not prepared to accept the liability
associated with the use of the Product, purchaser is advised to
return the Product immediately in new and unused condition to
the place of purchase.
Law
These terms are governed by Illinois law (without regard to
conflict of law principals). This warranty gives you specific legal
rights, and you may also have other rights which vary from state
to state. Horizon reserves the right to change or modify this
warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide
warranty support or service. Once assembly, setup or use of the
Product has been started, you must contact your local distributor
or Horizon directly. This will enable Horizon to better answer your
questions and service you in the event that you may need any
assistance. For questions or assistance, please visit our website
at www.horizonhobby.com, submit a Product Support Inquiry, or
call the toll free telephone number referenced in the Warranty
and Service Contact Information section to speak with a Product
Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is
compliant in the country you live and use the Product in,
please use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a Return
Merchandise Authorization (RMA) number. Pack the Product
securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors
of shipping without additional protection. Ship via a carrier that
provides tracking and insurance for lost or damaged parcels, as
Horizon is not responsible for merchandise until it arrives and is
accepted at our facility. An Online Service Request is available at
http://www.horizonhobby.com/content/_service-center_render-
service-center. If you do not have internet access, please
contact Horizon Product Support to obtain a RMA number along
with instructions for submitting your product for service. When
calling Horizon, you will be asked to provide your complete
name, street address, email address and phone number where
you can be reached during business hours. When sending
product into Horizon, please include your RMA number, a list
of the included items, and a brief summary of the problem. A
copy of your original sales receipt must be included for warranty
consideration. Be sure your name, address, and RMA number
are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you
have any issue with a LiPo battery, please contact the
appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your
original sales receipt verifying the proof-of-purchase
date. Provided warranty conditions have been met, your
Product will be serviced or replaced free of charge. Service or
replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service
will be completed and payment will be required without
notification or estimate of the expense unless the
expense exceeds 50% of the retail purchase cost. By
submitting the item for service you are agreeing to payment of
the service without notification. Service estimates are available
upon request. You must include this request with your item
submitted for service. Non-warranty service estimates will be
billed a minimum of ½ hour of labor. In addition you will be billed
for return freight. Horizon accepts money orders and cashier’s
checks, as well as Visa, MasterCard, American Express, and
Discover cards. By submitting any item to Horizon for service,
you are agreeing to Horizon’s Terms and Conditions found on
our website http://www.horizonhobby.com/content/_service-
center_render-service-center.
ATTENTION: Horizon service is limited to Product
compliant in the country of use and ownership. If
received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging
return shipment of the un-serviced Product, through
a carrier of the sender’s choice and at the sender’s
expense. Horizon will hold non-compliant Product for a
period of 60 days from notification, after which it will be
discarded.
10/2015
14
EN
Warranty and Service Contact Information
FCC Information
FCC ID (Transmitter): BRWDXMTX10
FCC ID (Quadcopter): BRWBLH9706
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with
the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
IC Information
IC (Transmitter): 6175A-BRWDXMT
IC (Quadcopter): 6157A-BLH9706
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Country of
Purchase
Horizon Hobby Contact Information Address
United States of
America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/
RequestForm/
1608 Interstate Drive
Champaign, Illinois, 61822 USA
Horizon Product Support
(Product Technical Assistance)
productsupport@horizonhobby.com
877-504-0233
Sales
websales@horizonhobby.com
800-338-4639
European Union
Horizon Technischer Service service@horizonhobby.eu
Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100
EU Compliance Statement:
BLH9700: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements
and other relevant provisions of the RED and EMC Directives.
BLH9750: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other
relevant provisions of the RED Directive.
A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-
compliance.
Compliance Information for the European Union
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their
waste equipment by handing it over to a designated collections point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and make sure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your waste equipment for recycling, please
contact your local city offi ce, your household waste disposal service or where you purchased the product.
15
DE
WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen
vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönli-
chem Eigentum führen oder schwere Verletzungen verursachen.
Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden
und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und verantwortungs-
volle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten führen. Dieses
Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines Erwachsenen. Versuchen
Sie nicht ohne Genehmigung durch Horizon Hobby, LLC, das Produkt zu zerlegen, es mit inkompatiblen Komponenten
zu verwenden oder auf jegliche Weise zu erweitern. Diese Bedienungsanleitung enthält Anweisungen für Sicherheit,
Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung alle Anweisungen
und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben werden kann und
Schäden oder schwere Verletzungen vermieden werden.
Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahren-
risiken beim Betrieb dieses Produkts hinzuweisen:
WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,
Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberfl ächliche Verletzungen.
ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die
Gefahr von schweren Verletzungen.
HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe
oder keine Gefahr von Verletzungen ergeben.
Halten Sie stets in allen Richtungen einen Sicherhe-
itsabstand um Ihr Modell, um Zusammenstöße oder
Verletzungen zu vermeiden. Dieses Modell wird von
einem Funksignal gesteuert, das Interferenzen von
vielen Quellen außerhalb Ihres Einfl ussbereiches unter-
liegt. Diese Interferenzen können einen augenblicklichen
Steuerungsverlust verursachen.
Betreiben Sie Ihr Modell immer auf einer Freifl äche ohne
Fahrzeuge in voller Größe, Verkehr oder Menschen.
Befolgen Sie stets sorgfältig die Anweisungen und
Warnhinweise für das Modell und jegliche optionalen
Hilfsgeräte (Ladegeräte, Akkupacks usw.).
Bewahren Sie alle Chemikalien, Klein- und Elektroteile
stets außerhalb der Reichweite von Kindern auf.
Setzen Sie Geräte, die für diesen Zweck nicht speziell
ausgelegt und geschützt sind, niemals Wasser aus.
Feuchtigkeit kann die Elektronik beschädigen.
Stecken Sie keinen Teil des Modells in den Mund, da
dies zu schweren Verletzungen oder sogar zum Tod
führen kann.
Betreiben Sie Ihr Modell nie mit fast leeren Senderak-
kus.
Halten Sie das Fluggerät immer in Sicht und unter
Kontrolle.
Gehen Sie sofort auf Motor Aus bei Rotorberührung.
Verwenden Sie immer vollständig geladene Akkus.
Lassen Sie immer den Sender eingeschaltet wenn das
Fluggerät eingeschaltet ist.
Nehmen Sie vor der Demontage des Fluggerätes die
Akkus heraus.
Halten Sie bewegliche Teile immer sauber.
Halten Sie die Teile immer trocken.
Lassen Sie Teile immer erst abkühlen bevor Sie sie
anfassen.
Nehmen Sie die Akkus/Batterien nach Gebrauch heraus.
Betreiben Sie Ihr Fluggerät niemals mit beschädigter
Verkabelung.
Fassen Sie niemals bewegte Teile an.
HINWEIS
Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby, LLC
jederzeit geändert werden. Die aktuelle Produktliteratur fi nden Sie auf horizonhobby.com unter der Registerkarte „Support“
für das betreffende Produkt.
Spezielle Bedeutungen
Sicherheitsvorkehrungen und Warnhinweise
Nicht geeignet für Kinder unter 14 Jahren. Dies ist kein Spielzeug.
16
DE
Box Inhalt
Komponenten
Spezifi kationen
• Blade
®
Ozone
• 3.7V 25C 500mAh 1S Li-Po Akku (nur RTF)
• 1S USB Li-Po Ladegerät (nur RTF)
• MLP4DSM Sender (nur RTF)
• 4 AA Batterien (nur RTF)
Inhaltsverzeichnis
Länge
172mm
Höhe
56mm
Propeller Durchmesser
65mm
Fluggewicht
75 g
Sie können Ihr Produkt online unter
www.bladehelis.com registrieren.
Komponenten ................................................................16
Spezifi kationen ..............................................................16
Box Inhalt ......................................................................16
Vorbereitung für den Erstfl ug .........................................17
Checkliste zum Fliegen ..................................................17
Akku-Warnhinweise .......................................................17
Aufl aden des Flugakkus .................................................17
Einsetzen der Senderbatterien (RTF) ..............................18
Einsetzen des Flugakkus ................................................18
Binden von Sender und Empfänger ................................19
SAFE Technologie ..........................................................20
Sendersteuerung ...........................................................20
Auswahl des Flugmodus ................................................21
LED Anzeigen .................................................................21
Einführung in die Hauptsteuerfunktionen........................22
Fliegen des Ozone .........................................................23
Checkliste für die Kontrolle und Wartung nach dem Flug 23
Hilfestellung zur Problemlösung .....................................23
Explosionszeichnung......................................................25
Teileliste ........................................................................25
Garantie und Service Informationen ...............................26
Garantie und Service Kontaktinformationen....................27
Konformitätshinweise für die Europäische Union ............27
RTF BLH9700 BNF BLH9750
Rumpf – Blade
®
Ozone
(BLH9700) Inklusive Inklusive
Motoren – 8,53mm gebürstet, (BLH9709, CW) (BLH9710, CCW) Eingebaut Eingebaut
Elektronikplatine – Hauptschalttafel, SAFE
®
(BLH9706) Eingebaut Eingebaut
Akku – 500mAh 1S 3,7V 25C Li-Po (EFLB5001S25UM) Inklusive Erforderlich
Lader – 1S USB Li-Po, 500 mAh, Hochstrom-UMX (EFLC1013) Inklusive Erforderlich
Sender – MLP4DSM 2.4 GHz, 4 CH, BCMX2 (EFLH1064/B) Inklusive Erforderlich
17
DE
Das dem Blade Ozone beiliegende Akkuladegerät (EFLC1013)
wurde speziell auf eine sichere Aufl adung des Li-Po-Akkus
ausgelegt.
ACHTUNG: Alle Anweisungen und Warnhinweise
müssen genau befolgt werden. Falsche Handha-
bung von Li-Po-Akkus kann zu Brand, Personen- und/oder
Sachwertschäden führen.
Durch Handhabung, Aufl adung oder Verwendung des mitge-
lieferten Li-Po-Akkus übernehmen Sie alle mit Lithiumakkus
verbundenen Risiken.
Sollte der Akku zu einem beliebigen Zeitpunkt beginnen, sich
aufzublähen oder anzuschwellen, stoppen Sie die Verwendung
unverzüglich. Falls dies beim Laden oder Entladen auftritt,
stoppen Sie den Lade-/Entladevorgang, und entnehmen Sie
den Akku. Wird ein Akku, der sich aufbläht oder anschwillt,
weiter verwendet, geladen oder entladen, besteht Brandge-
fahr.
Lagern Sie den Akku stets bei Zimmertemperatur an einem
trockenen Ort.
Bei Transport oder vorübergehender Lagerung des Akkus
muss der Temperaturbereich zwischen 40°F und 120°F (ca.
5 – 49°C) liegen. Akku oder Modell dürfen nicht im Auto oder
unter direkter Sonneneinstrahlung gelagert werden. Bei Lage-
rung in einem heißen Auto kann der Akku beschädigt werden
oder sogar Feuer fangen.
Laden Sie die Akkus immer weit entfernt von brennbaren
Materialien.
Überprüfen Sie immer den Akku vor dem Laden und laden Sie
niemals defekte oder beschädigte Akkus.
Verwenden Sie ausschließlich ein Ladegerät das speziell für
das Laden von LiPo Akku geeignet ist. Das Laden mit einem
nicht geeignetem Ladegerät kann Feuer und / oder Sachbe-
schädigung zur Folge haben.
Überwachen Sie ständig die Temperatur des Akkupacks
während des Ladens.
Trennen Sie immer den Akku nach dem Laden und lassen das
Ladegerät abkühlen.
Entladen Sie niemals ein LiPo Akku unter 3V pro Zelle unter
Last.
Verdecken Sie niemals Warnhinweise mit Klettband.
Lassen Sie niemals Akkus während des Ladens unbeauf-
sichtigt.
Laden Sie niemals Akkus ausserhalb ihrer sicheren Grenzen.
Laden Sie nur Akkus die kühl genug zum anfassen sind.
Versuchen Sie nicht das Ladegerät zu demontieren oder zu
verändern.
Lassen Sie niemals Minderjährige Akkus laden.
Laden Sie niemals Akkus an extrem kalten oder heißen
Plätzen (empfohlener Temperaturbereich 5 – 49°) oder im
direkten Sonnenlicht.
Akku-Warnhinweise
Aufl aden des Flugakkus
HINWEIS: Laden Sie nur Akkus die kühl genug zum Anfas-
sen und unbeschädigt sind. Bitte prüfen Sie den Akku um
sicher zu stellen, dass er nicht beschädigt, angeschwollen,
verbogen, gebrochen und punktiert ist.
1. Stecken Sie das Ladegerät in den USB Anschluss.
2. Schließen Sie den Akku an das Ladekabel an.
3. Trennen Sie nach dem Laden den Akku unverzüglich vom Ladegerät.
ACHTUNG: Verwenden Sie nur Ladegeräte die zum Laden von LiPo Akkus geeignet sind. Ein Nichtbefolgen könnte zu
Feuer, Sachschäden und Verletzungen führen.
ACHTUNG: Überschreiten Sie niemals den empfohlenen Ladestrom.
LED Anzeige
Nach korrektem Anschluss leuchtet die LED auf dem Ladegerät Rot und zeigt damit den Ladevorgang an. Das Laden eines entla-
denen (nicht tiefentladenen) 500mAh Akkus dauert ca. 60 Minuten. Nach erfolgtem Ladevorgang ist die LED aus.
LADEN (leuchtet Rot)
LADEN FERTIG (AUS)
ACHTUNG: Entnehmen Sie nach dem Ladevorgang unverzüglich den Akku. Lassen Sie niemals den Akku am Ladegerät
angeschlossen.
Vorbereitung für den Erstfl ug
Entnehmen und überprüfen Sie die Komponenten
Laden Sie den Flugakku
Setzen Sie den Akku ein wenn er vollständig geladen ist
Programmieren Sie Ihren Sender (nur BNF Version)
Binden Sie Ihren Sender (nur BNF Version)
Machen Sie sich mit den Kontrollen vertraut
Finden Sie eine geeignete Fläche zum fl iegen
Checkliste zum Fliegen
Schalten Sie immer den Sender zuerst ein
Stecken Sie den Flugakku an den Anschluß der
Kontrolleinheit an
Lassen Sie der Kontrolleinheit Zeit zum initialisieren und
armieren
Fliegen Sie das Modell
Landen Sie das Modell
Stecken Sie den Flugakku von der Kontrolleinheit ab
Schalten Sie immer den Sender als letztes aus
18
DE
Einsetzen der Senderbatterien (RTF)
Blinkt die LED und ertönt ein Piepton müssen die Senderbatterien
gewechselt werden.
Einsetzen des Flugakkus
12
3
4
1. Die Gaszufuhr in die niedrigste Einstellung bringen. Bei BNF-Flugzeugen „Gas halten“ aktivieren, wenn Ihr Sender so
ausgerüstet ist.
2. Sender einschalten.
3. Einsetzen der Akkus durch Einschieben in den Akku-Halterungsschlitz unter der Steuereinheit. Akku mit dem Etikett
nach oben in die Schlitze schieben, sodass der in die Akkuendkappe eingefasste Akkutaster in Kontakt kommt mit
dem Taster auf dem Akkufach.
4. Das Akku-Kabel mit der Steuereinheit verbinden.
5. Stellen Sie den Quadcopter auf eine ebene Fläche und lassen Sie das Flugzeug stehen, bis die LED an der Steuerein-
heit einen der folgenden Flugmodi anzeigt:
Durchgängig blau: Stabilitäts Modus, Schalterposition 1
Durchgängig rot: Agilitätsmodus, Schalterposition2
ACHTUNG: Trennen Sie immer den Akku vom Quadcopter, wenn Sie nicht fl iegen, um ein Tiefentladen des
Akkus zu vermeiden. Akkus, die unter die zulässige Grenze entladen werden, können dabei beschädigt werden,
was zu Leistungsverlust und potenzieller Brandgefahr beim Laden führen kann.
19
DE
ACHTUNG: Wenn Sie einen Futaba-Sender mit einem Spektrum DSM-Modul verwenden, müssen Sie den
Gaskanal reversieren (umkehren) und danach das System neu binden. Lesen Sie bitte für den Bindevorgang
und programmieren der Failsafeeinstellungen die Bedienungsanleitung des Spektrum Modules. Zum reversieren des
Gaskanals lesen Sie bitte in der Anleitung des Futaba Senders nach.
* Dieser Stickschalter kann ebenfalls für den Bindevorgang verwendet werden.
Wenn Probleme auftreten beachten Sie bitte die Bindeanweisungen und schauen in die Hilfestellung zur
Problemlösung. Kontaktieren Sie falls notwendig den technischen Service von Horizon Hobby. Eine Liste der
kompatiblen DSM Sender sehen Sie unter www.bindnfl y.com.
RTF
Binden von Sender und Empfänger
Ihr RTF Sender ist bereits an das Modell gebunden. Sollten Sie neu binden wollen folgen Sie bitte den
untenstehenden Anweisungen.
MLP4DSM Bindeprozess
1. Den Flug-Akku vom Quadcopter trennen.
2. Alle Trimmungen auf Ihrem Sender zentrieren.
3. Den Sender ausschalten und den Gashebel in die Position niedrig/aus bringen.
4. Den Flug-Akku am Quadcopter anschließen. Die LED auf dem Steuergerät blinkt nach 5 Sekunden.
5. Wenn das blaue Licht blinkt, den linken Knüppel* gedrückt halten, während sich der Sender einschaltet
(es ist ein „Klicken“ zu hören).
6. Den linken Knüppel loslassen. Der Sender wird einen Piepton abgeben und die Strom-LED wird blinken.
7. Der Quadcopter ist gebunden, wenn alle LEDs auf dem Flugzeug durchgängig leuchten.
8. Den Flug-Akku trennen und den Sender ausschalten.
Bei Verwendung eines Computersenders den Modelltyp auf „Acro“ oder „Flugzeug“ einstellen. Kanal 6 (Aux1) im Ka-
naleingangsmenü auf momentanes Schalten stellen, wie z.B. den Bindungsschalter (I) und den Getriebekanal 5 (Gear)
auf einen 3-Positionen-Schalter (Schalter B). Im Servo-Setup-Menü Kanal 6 (Aux1) umkehren.
Den Quadcopter an Ihren Sender binden unter Beachtung der nachfolgenden Anweisungen zum Binden des Senders
und Empfängers.
Der Bindevorgang
1. Den Flug-Akku vom Quadcopter trennen.
2. Alle Trimmungen auf Ihrem Sender zentrieren.
3. Den Sender ausschalten und die Gaszufuhr vollständig senken.
4. Den Flug-Akku an den Quadcopter anschließen. Alle LEDs am Flugzeug blinken schnell und zeigen damit an, dass
das Flugzeug in den Bindungsmodus übergegangen ist.
5. Den Sender während des Einschaltens in den Bindungsmodus bringen.
6. Den Bindungstaster/-schalter nach 2 bis 3 Sekunden loslassen. Der Quadcopter ist gebunden, wenn alle LEDs
auf dem Flugzeug durchgängig leuchten.
7. Den Flug-Akku trennen und den Sender ausschalten.
20
DE
RTF
Sendersteuerung
Die revolutionäre SAFE Technologie von Horizon Hobby (Sensor Assited Flight Envelope) verwendet eine innovative Kombination
aus Multi-Achs Sensoren und Software, die es erlauben, die relative Position des Fluggerätes im Raum jederzeit zu bestimmen.
Diese dreidimensionale Wahrnehmung schafft eine schräglagenbegrenzte Fluglage die Sie sicherer Fliegen läßt. Dabei werden
Roll- und Nickwinkel beeinfl usst und geregelt, um die Flugsicherheit zu erhöhen. Und das System kann weit mehr, als die
Stabilisierung des Fluggerätes. Die verschiedenen Flugmodi können vom Piloten gemäß seiner Fähigkeiten individuell eingestellt
werden.
SAFE Technologie im Überblick:
• Flugstabilisierung über einen Schalter zuschaltbar.
• Mehrere Modi zur Anpassung von SAFE and die Fähigkeiten des Piloten.
Und das Beste an allem ist, dass SAFE keine weiteren Einstellungen und Vorbereitungen erfordert. Jedes Modell, welches
mit SAFE ausgestattet wurde, verfügt über eine angepasste und optimierte Programmierung der Elektronik, um für maximale
Sicherheit und maximalen Flugspaß zu sorgen. FLYSAFERC.com
Technologie
®
ABCDEF
Modus
1
Querruder (links/rechts)
Gas (auf/ab)
Gas trimm
Querruder-
trimm
Seitenruder-
trimm
Höhenruder-
trimm
Seitenruder
(links/rechts)
Höhenruder
(auf/ab)
Modus
2
Querruder (links/rechts)
Höhenruder (auf/ab)
Höhenruder-
trimm
Querruder-
trimm
Seitenruder-
trimm
Gas trimm
Seitenruder
(links/rechts)
Gas (auf/ab)
D
E
F
• Ein/Aus-LED
C
B
A
EIN/AUS-Schalter
Wenn die Trimmtasten gedrückt werden, geben sie einen Signalton von sich, der bei jedem erneuten Drücken höher
oder tiefer wird. Die mittlere oder neutrale Trimmstellung erklingt in der mittleren Tonhöhe. An den äußeren Enden des
Steuerbereichs erklingt eine Tonfolge.
Auswahl des
Flugmodus
• Einbinden
• Langes Drücken:
Ein-/Ausschalten
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Blade OZONE RTF BLH9700 Manuel utilisateur

Catégorie
Jouets télécommandés
Taper
Manuel utilisateur