DCS RF24BTR1 Guide d'installation

OUTDOOR BEER DISPENSERS

Installation, Operation and Maintenance Instructions

MODELS:

MODÈLES:

RF24TR1

RF24TL1

RF24BTR1

RF24BTL1

DISTRIBUTEURS DE BIÈRE D’EXTÉRIEUR

Instructions d’installation, d’utilisation et d’entretien

2

NOTE

!

CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ...................................................3

Warranty registration............................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product dimensions ............................................................8

Using your Electronic control...............................................9

Starting your appliance....................................................9

Turning your appliance "ON" or "OFF".............................9

Adjusting the temperature................................................9

Beer dispenser operation..................................................9

Alarms............................................................................9

Door ajar......................................................................9

Temperature sensor fault............................................9

High and Low temperature alarms..............................9

Alarm mute......................................................................9

Using your beer dispenser.................................................10

Tap equipment and assembly.......................................10

CO2 regulator.................................................................14

Drain kit..........................................................................15

Care and cleaning ............................................................15

Cleaning the drain sump................................................15

Keg coupler cleaning.....................................................16

Faucet cleaning ............................................................16

Front grille .....................................................................16

Cabinet.........................................................................16

Interior...........................................................................16

Long term storage / winterization .......................................17

Stainless steel maintenance ............................................19

Energy saving tips .............................................................20

Troubleshooting .................................................................21

Obtaining service .............................................................21

Warranty ............................................................................22

US

CA

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals

known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals

known to the State of California to cause birth defects or

other reproductive harm.

3

A Message To Our Customers

Thank you for selecting this DCS Outdoor Refrigerator.

Because of this appliances’ unique features we have devel-

oped this Use and Care and Installation Guide. It contains

valuable information on how to properly install, operate and

maintain your new appliance for years of safe and enjoy-

able operation.

For your convenience, product questions can be answered

by a DCS Customer Care Representative at

1-888-936-7872, or email: customer.care@sherpaykel.com

NOTE: Please write the Model, Code, and Serial Number

on this page for references (the serial plate is located on

the upper left side, inner wall).

MODEL NUMBER:

CODE:

SERIAL NUMBER:

NOTE: Inspect the product to verify that there is no ship-

ping damage. If any damage is detected, call the shipper

and initiate a damage claim. DCS by Fisher & Paykel is not

responsible for shipping damage.

DO NOT discard any packing material (box, pallet, straps)

until the unit has been inspected.

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

US

CA

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

NOTE

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

!

CAUTION

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

UNPACKING YOUR APPLIANCE

4

!

CAUTION

US

CA

Figure 1

Front Leveling

Legs

Front Grille,

keep this area

open.

Rear

Leveling

Legs

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from

55 to 115°F (13 to 46°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstructed.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean (See Figure 1). The use of a custom

made grille is not recommended as it may restrict air ow.

INSTALLING YOUR APPLIANCE

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The

overall height of your appliance may be adjusted between

the minimum, 33

3

⁄4" (85.7 cm), by turning the leveling leg in

(CW ↷) and the maximum, 34

3

⁄4" (88.3 cm) by turning the

leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 2).

Figure 2

Front grille screw

Front grille

5

NOTE

Figure 5

US

CA

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 5). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

6

!

CAUTION

NOTE

Anti-Tip Device

US

CA

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

Figure 6

Bottom View of

Beer dispenser

Anti-Tip

Bracket

Leveling Leg

Front of cabinet

21

1

⁄2"

(54.6 cm)

Step by step instructions for locating the

position of the bracket:

1) Decide where you want to place the beer dispenser.

Slide it into place, being careful not to damage the oor,

leaving 1" (2.5 cm) of clearance from the rear wall to allow

room for the anti-tip bracket.

2) Raise the rear leveling legs approximately

1

⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the beer dispenser is in the desired location,

then mark on the oor the rear and side corner of the cabi-

net where the anti-tip bracket will be installed. If the instal-

lation does not allow marking the rear corner of the cabinet,

then make temporary lines on the oor marking the front

corner of the cabinet, excluding the door. Slide the beer

dispenser out of the way. From the temporary line extend

the sidewall line back 21

1

⁄2" (54.6 cm) as shown in Figure 6.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

1

⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 7).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the beer dispenser as shown in

Figure 6.

!

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

!

WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

7

NOTE

US

CA

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

"V" notches

in bracket

"V" notches

in bracket

When the oor mounted anti-tip bracket is used the mini-

mum adjusted height of the cabinet is increased by

3

⁄8" (9 mm).

Figure 7

Front of cabinet line

Rear of cabinet line

Figure 7a

21

1

⁄2"

(54.6 cm)

Rear Leveling leg

Screw

Side of cabinet line

8

"A"

"B"

"C"

"D"

"E"

"H"

"G"

"F"

"J"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

US

CA

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

All Models

24

1

⁄4" (61.6 cm)

24 ½" (62 cm)

(with optional DCS

side trim kit)

**34" to 35"

(86.4 to 88.9 cm)

*

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

26

1

⁄4"

(66.7 cm)

46

13

⁄32"

(117.9 cm)

26

1

⁄4"

(66.7 cm)

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS***

PRODUCT

WEIGHT

All Models 115V/60Hz/15A

140 lbs

(63.6 kg)

Figure 9

21

1

⁄2"

(54.6 cm)

12

1

⁄4"

(31.1 cm)

11

15

⁄16"

(30.3 cm)

11"

(27.9 cm)

Figure 8

* Depth dimension of rough-in opening may vary depend-

ing on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug

is required.

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

*** A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

PRODUCT DIMENSIONS

Figure 8a

9

US

CA

USING YOUR ELECTRONIC CONTROL

• Temperature Sensor Fault: If the control-

ler detects that the temperature sensor is not

properly functioning, a temperature sensor

alarm will sound in one (1) second intervals. "E1" will ash

on the display panel and the Alarm LED located at the top

left of the display below the word "Alarm" will be illuminated.

• High and Low Temperature Alarm: If your

unit reaches an unacceptable temperature

outside of your set-point, the alarm will sound

in (1) second intervals. The display panel will

ash either "Hi" or "Lo" depending upon the

condition and the Alarm LED light at the top

left of the display below the word "Alarm" will be illuminat-

ed. These alarms indicate that the compartment tempera-

ture has moved 10° or more from the set point for more

than 1 hour duration. The alarm will remain active until the

condition is corrected.

NOTE

During initial appliance start-up, the high temperature alarm

may sound until the interior temperature reaches set point.

The high temperature alarm can also occur if the door re-

mains open during an extended period of time (i.e. cleaning

or door ajar alarm condition), high usage or loading with

warm product. After a high temperature alarm condition check

all perishables to ensure they are safe for consumption.

Alarm Mute

Press any key to mute the audible portion of an alarm.

NOTE

This action will only mute the alarm. If the condition that

caused the alarm continues, the alarm code will continue to

ash and will sound for 20 seconds every 60 minutes.

Starting your beer dispenser

Plug the beer dispenser power cord into a wall outlet. Your

beer dispenser will begin cooling after power is applied.

If your beer dispenser does not start, check that the beer dis-

penser is turned on and the set temperature is cold enough.

Turning your beer dispenser ON or OFF

If the beer dispenser is on, the beer dispenser temperature

will be shown on the display. To turn the beer dispenser

off, press and hold the "ON/OFF" button for three seconds.

"OFF" will appear on the display.

If the beer dispenser is not on, "OFF" will be shown on the

display. To turn the beer dispenser on, press and hold the

"ON/OFF" button for three seconds. The beer dispenser

temperature will be shown on the display.

Set temperature

To set the beer dispenser temperature, press and hold

the "SET" button. When the "SET" button is pressed, the

display will show the set temperature. While holding the

"SET" button, press the "WARMER" or "COLDER" buttons

to adjust set temperature.

Beer dispenser operation

The available temperature range of the beer dispenser is

34 to 46°F (1 to 8°C).

It may take up to 24 hours for your beer dispenser to reach

desired temperature. This will depend on amount of content

loaded and number of door opening and closings.

For best results allow beer dispenser to "pull down" to

desired set temperature before loading. Once contents are

loaded, allow at least 48 hours for temperature to stabilize

before making any adjustments to the set temperature.

Alarms

Your digital display function will monitor beer dispenser

function and alert you with a series of audible and

visual alarms.

• Door Ajar Alarm: If the door has been left

open for over ve minutes, the alarm will

sound in one second intervals. The display

panel will ash "do" and the Alarm LED located at the top

left of the display below the word "Alarm" will be illuminat-

ed. This will stop as soon as the door is closed.

Set

Colder Warmer

ON/OFF

Press and Hold Press and Hold

Alarm

F

Figure 11

Figure 10

close-up of control

10

USING YOUR BEER DISPENSER

Tap Equipment and Assembly

Your dispensing kit includes the following parts:

Polished stainless steel tower with clear beer line (single

or double dispense)

Tower Gasket

Phillips oval head screws

Knob for Tower (Faucet Handle)

Keg coupler(s)

CO2 regulator with red gas line(s) attached

Empty 5 pound CO2 tank

Plastic clamp(s) large and small

Faucet wrench

Tools required for installation:

Flat bladed screwdriver

Phillips screwdriver

Pliers

Adjustable wrench or a 1

1

⁄8" open end wrench

1

⁄2" open end wrench

Barrel Sizes

1/6 barrel 1/4 Barrel 1/2 Barrel

Height

23

5

⁄16"

(59.2 cm)

14

13

⁄16"

(37.6 cm)

23

5

⁄16"

(59.2 cm)

Diameter

9

1

⁄4"

(23.5 cm)

17"

(43.2 cm)

17" to 17

1

⁄4"

(43.2 to 43 cm)

Gallons 5.16 7.75 15.5

#12 ounce

Glasses

60 82 163

This beer dispensing unit will support

1

⁄2 barrel or

1

⁄4 bar-

rel. The double draft tower units can support two sixth (

1

⁄6)

barrels of beer. See chart below for quantity of beer in each

barrel size.

Table A

Table B

Keg Size

#of kegs per

5 pound CO2 Tank

5 gallon Corny 15 to 22

1/6 barrel 14 to 21

1/4 Barrel 10 to 14

1/2 Barrel 5 to 7

CO2 can be dangerous. If it becomes difcult to

breathe and/or your head starts to ache, a high

concentration of carbon dioxide may be present.

Leave the area immediately.

• The CO2 tank must always be connected to the

regulator. Never connect the tank to the keg.

• The CO2 tank must be securely mounted in the

upright position. Secure it with the chain pro-

vided.

• Never drop or throw the CO2 tank.

• Keep the CO2 tank away from heat.

• Ventilate the area after a CO2 leak.

!

WARNING

1. Remove shelving and packaged components from the

interior of the refrigerator before beginning the assem-

bly process.

2. Take your empty 5 pound CO2 tank to your local gas

supply dealer to be lled. You can usually nd them in

your "yellow pages" under "Welding Supply" or "Fire

Protection". One 5 pound tank can process many kegs

(see table "B") Your dealer should supply you with a

new plastic washer every time the tank is lled. This

washer is used at the regulator to tank connection. See

Figure 15 and 22 on page 11. Replace the old washer

with the new one whenever the tank is relled.

3. Tower mounting (if you are installing the unit under a

counter skip to step 4). If you are mounting the tower

directly to the top of the refrigerator, rst remove the

four screws from the top of the refrigerator. Remove the

foam plug from the large hole in the top of the refrigera-

tor. Feed the clear beer line through the tower gasket

and the large hole in the refrigerator top. Align the 4

holes in the tower with the 4 holes in the refrigerator

top and secure the tower with the 4 screws removed

previously. Skip to step 5.

US

CA

11

B

5 Pound

CO2 Tank

5 Pound

CO2 Tank

Figure 15

Figure 21

A

C

Regulator

with red

airline

Regulator

with red

airline

Keg

Coupler

Keg

Coupler

Keg

Coupler

Single

Dispense

Tower

Double

Dispense

Tower

A

C

Hose clamps

use for connections

and

A

C

Hose clamps

use for connections

and

A A

Single Dispense Tower Kit

Connect to ,etc........

A A

Double Dispense Tower Kit

Connect to ,etc........

Figure 12

Figure 13

Figure 14

Figure 19

Figure 20

Figure 22

Figure 18

Figure 16

Figure 17

New plastic

washer

New plastic

washer

US

CA

USING YOUR BEER DISPENSER

12

4. If you are installing your keg refrigerator under a

counter you will need to drill 5 holes in the counter top

to mount the tower. The rst hole is a 1

1

⁄2" diameter

hole located at the center of the tower for the beer

line, locate approximately 13

1

⁄2" (34.3 cm) from the

front edge of the counter top (based on a counter top

depth of 25

5

⁄16"). Next drill the 4 tower mounting holes

per the dimensions in Figure 23. The hole diameter

is dependent on the counter top material and if screw

anchors are required. The screws supplied are in the

literature pack and are a #10 x 1" type AB stainless

steel screw. Mark and cut the rectangular cutout for

the drain sump. After the holes are drilled and the

keg refrigerator is in place under the counter top feed

the beer line through the tower gasket, the 1

1

⁄2" hole

in the counter top and the hole in the top of the keg

refrigerator. Mount the tower to the counter top with the

4 screws provided. Place the counter top drain sump,

from the literature pack, in the rectangular hole with the

radius cutout to the rear around the tower and place

the grate in the sump.

5. Mount the regulator to the CO

2 tank (connection

B

)

use the new plastic washer you received from the gas

supply company. Note that the regulator has left hand

threads and has to be turned counterclockwise to

tighten. Tighten with the adjustable wrench or the 1

1

⁄8"

open end wrench.

6. Connect the red air line(s) from the regulator to the

large air line tting on the keg coupler with a large

hose clamp (connection

C

).

7. Connect the clear beer line from the tower to the small

air line tting on the keg coupler with a small hose

clamp (connection

A

).

Figure 23

Figure 24

Figure 25

Tower

!

CAUTION

The cutout dimensions shown in Figure 23 are based on

a 25

5

⁄16" (64.3 cm) deep counter top. Your counter top may

be different than this and require other front to back dimen-

sioning. Refer to the product dimensions on page 8 when

determining the required dimensions.

Grate from top of

beer dispenser

Counter top

sump from

literature pack

Rear of counter top

1

3

⁄8"

(3.5 cm)

typical

1

⁄2" (38 mm)

Diameter

2

7

⁄38"

(7.3 cm)

4

1

⁄4"

(10.8 cm)

6

3

⁄8"

(16.2 cm)

1

⁄4" (6 mm)

radii,

typical

12

1

⁄4"

(31.1 cm)

6

1

⁄8"

(15.6 cm)

counter

top depth

25

5

⁄16"

(64.3 cm)

Diameter

to suit

US

CA

USING YOUR BEER DISPENSER

13

Figure 27

Figure 27a

Rotate the top of the coupler coun-

ter clockwise to extend the coupler

to the to the "OFF"position.

Coupler

extended

8. Locate the CO

2 tank in the corner of the refrigerator as

shown in Figure 26 and secure with the chain. Close

the faucet handle on the tower.

9. Hooking up the keg coupler to the keg: Verify the cou-

pler is in the "OFF" position (see Figure 27a).Align the

lugs on the keg with the corresponding openings on the

keg coupler and turn clockwise until the coupler stops

(about 90°). Push down and twist the top of the coupler

clockwise to allow gas to enter the keg.

Figure 26

Chain-The chain is fastened

and taped to the top of the

interior liner. Remove the tape

and secure the CO

2 tank in

place in the back right corner.

Loop chain around top of tank

and connect with "S" hook.

Push faucet handle back toward

tower to close the faucet

Figure 26a

Connect with

"S" hook

US

CA

USING YOUR BEER DISPENSER

Lugs

on keg

Figure 27b

14

CO2 Regulator (Double Dispense Tower)

Your beer dispenser comes equipped with a 5 pound CO2

tank and a dual gauge regulator. The lower gauge should

be reading approximately 750 psi (52 bar) when the tank is

properly lled and the tank is not in the refrigerator (at room

temperature). The tank will read less when chilled. Use this

lower gauge as an indicator of how much CO2 you have left

in the tank.

The upper gauge reads the pressure being supplied to the

beer keg. Follow the procedure below to adjust the pres-

sure to 12 - 14 psi (0.8 to 1 bar) for lager beer or 9 - 12 psi

(0.6 to 0.8 bar) for ale's.

To adjust the pressure (Upper Gauge):

1. Close the shutoff valves at the bottom of the regulator.

2. Be sure the faucet handle is closed on the tower (see

Figure 29).

3. Loosen the lock nut by turning ↶ counterclockwise us-

ing the

1

⁄2" open end wrench until loose, this will allow

adjustment of the pressure adjustment screw.

4. With the at bladed screwdriver turn the adjustment

screw ↷ clockwise to increase the pressure or ↶ coun-

terclockwise to decrease the pressure.

5. Open the shutoff valve on the bottom of the regula-

tor. The gauge reading may drop but will return very

quickly.

6. Pull the ring on the keg coupler to allow the gas to ow

momentarily.

7. Make any ne adjustments if necessary with the adjust-

ment screw.

8. Tighten the locknut with the

1

⁄2" open end wrench by

turning clockwise ↷.

CO2 Regulator (Single Dispense Tower)

Your beer dispenser comes equipped with a 5 pound CO2

tank and a single gauge regulator. The gauge reads the

pressure being supplied to the beer keg. Follow the pro-

cedure below to adjust the pressure to 12 - 14 psi (0.8 to

1 bar) for lager beer or 9 - 12 psi (0.6 to 0.8 bar) for ale's.

To adjust the pressure (Single Gauge):

1. Close the shutoff valve at the bottom of the regulator.

2. Be sure the faucet handle is closed on the tower (see

Figure 26).

3. Loosen the lock nut by turning ↶ counterclockwise us-

ing the

1

⁄2" open end wrench until loose, this will allow

adjustment of the pressure adjustment screw.

4. With the at bladed screwdriver turn the adjustment

screw ↷ clockwise to increase the pressure or ↶ coun-

terclockwise to decrease the pressure.

5. Open the shutoff valve on the bottom of the regula-

tor. The gauge reading may drop but will return very

quickly.

6. Pull the ring on the keg coupler to allow the gas to ow

momentarily.

7. Make any ne adjustments if necessary with the adjust-

ment screw.

8. Tighten the locknut with the

1

⁄2" open end wrench by

turning clockwise ↷.

Ring on keg

coupler

Figure 29 (Regulator for

Single Dispense Tower)

Figure 30 (Regulator for

Double Dispense Tower)

Figure 28

(2) shutoff

valves (closed

position shown)

Upper Gauge

Pressure Gauge

Lower Gauge

Pressure

Adjustment

Screw

Lock Nut

US

CA

USING YOUR BEER DISPENSER

Pressure

Adjustment

Screw

Lock Nut

shutoff valve

(closed posi-

tion shown)

15

Figure 31

Drain kit (All Models): The drain kit is shipped in

place and ready to use. To empty: Pull drain hose out of

bottle cap, remove bottle from unit, unscrew cap and dis-

card waste and rinse bottle. Reinstall bottle in unit.

Unscrew

cap

Removable

grate for clean-

ing sump area

Cleaning the drain sump:

On a free standing beer dispenser remove the grate from

in front of the tower, clean with soap and water and dry

before reinstalling. Clean the sump area with soapy water

and dry. (See gure 31).

On a built in beer dispenser remove the grate and coun-

ter top sump, clean with soap and water and dry before

reinstalling. Clean the sump area with soapy water and dry.

(See Figure 32).

Counter top

sump

Clean and dry

sump area

Figure 32

Push faucet handle back toward

tower to close the faucet

USING YOUR BEER DISPENSER AND CARE AND CLEANING

US

CA

16

Faucet Cleaning

Turn off the gas supply with the shutoff valve(s) under the

regulator (see Figure 29 or 30) and open the faucet to re-

lieve the pressure. To remove the faucet from the tower use

the spanner wrench provided. Place the pin on the wrench

into the hole on the faucet collar and turn clockwise ↷ to

remove the faucet. (See Figure 35).

Remove the knurled cap from the faucet body just below

the handle and pull the handle assembly from the faucet.

This will allow the shaft to be removed from the back of the

faucet, see Figure 36.

Soak all faucet parts in hot water or a solution of hot water

and a sanitizing solution. Do not use soap. Rinse thorough-

ly with clean water.

Reassemble faucet, assemble faucet to tower (be sure

faucet is in off position), and turn on gas valve.

Figure 35

Figure 36

After removing the

handle the shaft will

slide out the back of the

faucet

Unscrew knurled

cap on faucet body

and remove handle

assembly

Place pin on

wrench into hole

in faucet collar.

CARE AND CLEANING

Cleaning

Remove the keg coupler from the keg if necessary. Close the

gas valve(s) below the regulator, remove both the red gas

line(s) and clear beer line(s) from the keg coupler(s) by remov-

ing the plastic hose clamps (See Figure 33). Soak and brush

the keg coupler in hot water or a sanitizing solution. Rinse

thoroughly with clean water. Dry all parts and reassemble.

Cleaning and Maintaining Dispensing System

The dispensing system needs to be cleaned between

usage to prevent spoilage and/or foul taste in your beer.

Figure 34

Figure 33

Hose clamps can be

released by a lateral

movement to the head.

!

CAUTION

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

US

CA

Cabinet

The stainless steel cabinet can be washed with either a

mild soap and water and thoroughly rinsed with clear water.

NEVER use abrasive scouring cleaners. Dry thoroughly

with a terry towel.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Front Grille

Be sure that nothing obstructs the required air ow openings

in front of the cabinet. At least once or twice a year, brush or

vacuum lint and dirt from the front grille area (see page 4).

17

CARE AND CLEANING

US

CA

Long term storage / winterization:

1. Time to Winterize, when the daily low ambient tempera-

ture is at or below 38°F (3.3°C).

2. Turn unit off, (see page 9).

3. Remove all contents.

4. If necessary, move the unit so you can gain access to

the rear of the product.

5. Unplug the unit from the power outlet.

6. It is also recommended that the power to the outlet be

turned-off if the circuit is not required for other items

during the Winter season.

7. Shut-off CO

2

tank valve.

8. Drain beer line(s)

9. Disassemble faucet and clean, (see page 16).

10. Soak and clean Sankey Low-Boy tap, (see page 16).

11. When cleaning unit pay particular attention to any

cracks and crevices that may have accumulated dirt

and debris.

12. Remove the front toe-grille, (see Figures 37 and 38),

and use a brush and vacuum to clean dirt and debris

from beneath the unit.

13. Thoroughly clean the toe-grille and re-install on the

unit.

14. Remove the rear access cover, (see Figure 39), and

use a brush and vacuum to clean dirt and debris from

the machine compartment.

15. Thoroughly clean the rear access cover and re-install

on the unit.

16. Wipe down all interior surfaces with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals which could cause staining. Do

not use any abrasive cleaners or scouring pads.

!

CAUTION

Operating of the unit at ambient temperatures below the

recommended Winterization temperature will void your war-

ranty.

a. Remove keg coupler (sankey tap), (see

page 16).

b. Remove faucet on tower, (see page 16).

c. Beer lines will gravity drain.

d. Clean beer line tubing.

• If the plastic defrost drain pan located

under the compressor contains water,

use a sponge to remove as much

water as possible

• Remove plastic oor protector and

stainless steel lower edge guard to

clean underneath.

Front grille screw

Front grille

Figure 37

Remove oor

protector and

edge guard

and clean

Floor protector

Edge

guard

Figure 38

Figure 38a

Grille

Spacer

Clean out

behind

grille

18

CARE AND CLEANING

US

CA

Start-Up After Long-Term Storage:

1. Connect the unit to electrical power.

2. If stored outside, it is recommended that the unit again

be thoroughly inspected per the storage instructions

above to address any dirt or debris from the weather

and/or animals/insects.

3. Turn unit on and conrm your desired control settings.

4. Allow 24-hrs for the unit to stabilize before loading

contents.

17. Leave door open and allow to completely dry out be-

fore closing door.

18. Thoroughly clean the door gasket with anti-bacterial

cleaner to be followed with clean rinse water to remove

any residual chemicals.

19. Thoroughly clean the exterior with a cleaner approved

for stainless steel . Do not use any abrasive cleaners

or scouring pads.

20. Any mounting hardware / fasteners that are showing

signs of corrosion should be replaced.

21. Once the exterior has been thoroughly cleaned, you

may want to apply a coating of car wax to help protect

against spotting from moisture, dirt, and debris that

may accumulate on the surfaces during the Winteriza-

tion period.

After completion of the above, you may choose to store the

unit indoors, although this is not required.

Remove 11

screws from

around the

perimeter of the

access cover

with a

5

⁄16" nut

driver.

Figure 39

Figure 40

Remove the power

cord from the grommet

in the access cover.

Soak up water

from plastic

drain pan if

necessary

Clean out

debris

19

US

CA

STAINLESS STEEL MAINTENANCE

Background

Stainless steel does not stain, corrode, or rust as easily as

ordinary steel, but it is not stain or corrosion proof. Stain-

less steels can discolor or corrode if not maintained prop-

erly.

Stainless steels differ from ordinary carbon steels by the

amount of chromium present. It is this chromium that

provides an invisible protective lm on the surface called

chrome-oxide. This protective chrome-oxide lm on the

surface can be damaged or contaminated, which may

result in discoloration, staining, or corrosion of the base

metal.

Care & Cleaning

Routine cleaning of the stainless steel surfaces will serve to

greatly extend the life of your product by removing contami-

nants. This is especially important in coastal areas which

can expose the stainless to severe contaminants such as

halide salts, (sodium chloride).

It is strongly recommended to periodically inspect and thor-

oughly clean crevices, weld points, under gaskets, rivets,

bolt heads, and any locations where small amounts of liquid

could collect, become stagnant, and concentrate contami-

nates. Additionally, any mounting hardware that is showing

signs of corrosion should be replaced.

Frequency of cleaning will depend upon the installation

location, environmental, and usage conditions.

Choosing a Cleaning Product

The choice of a proper cleaning product is ultimately that

of the consumer, and there are many products from which

to choose. Depending upon the type of cleaning and the

degree of contamination, some products are better than

others.

Typically the most effective and efcient means for routine

cleaning of most stainless steel products is to give the sur-

faces a brisk rubbing with a soft cloth soaked in warm water

and a gentle detergent, or mild mixture of ammonia. Rub-

bing should, to the extent possible, follow the polish lines of

the steel, and always insure thorough rinsing after cleaning.

Although some products are called "stainless steel clean-

ers," some may contain abrasives which could scratch the

surface, (compromising the protective chrome-oxide lm),

and some many contain chlorine bleach which will dull,

tarnish or discolor the surface if not completely removed.

After the stainless surfaces have been thoroughly cleaned,

a good quality car wax may be applied to help maintain the

nish.

Note: Stainless steel products should never be installed, or

stored in close proximity to chlorine chemicals.

Whichever cleaning product you chose, it should be used

in strict accordance with the instructions of the cleaner

manufacturer.

20

US

CA

ENERGY SAVING TIPS

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

La page est en cours de chargement...

DCS RF24BTR1 Guide d'installation

Ce manuel convient également à

DCS RF24BTR1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents