Stile CF0130 Mode d'emploi

Anderson 22 in. Enclosed Ceiling Fan

Anderson de 22 po Ventilateur de plafond

Ventilador de techo cerrado Anderson de 22 pulg.

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

AVERTISSEMENT :

Pour réduire les risques de

blessures, l’utilisateur doit lire et

veiller à bien comprendre le manuel

d’utilisation avant d’employer ce

produit.

ADVERTENCIA:

P

ara reducir el riesgo de lesiones,

el usuario debe leer y comprender

el manual del operador antes de

usar este producto

.

WARNING :

To reduce the risk of injury, the

user must read and understand

the operator’s manual before using

this product.

TABLE OF CONTENTS

****************

 Important Safety Instructions .................... 2

 Symbols ..................................................... 3

 Package Contents ..................................4-5

 Tools Needed ............................................. 5

 Product Specifications ............................... 6

 Installation ............................................. 6-15

 Operation ............................................16-17

 Maintenance ............................................ 18

 Troubleshooting ....................................... 19

 Warranty ................................................... 20

 Parts Ordering and Service ......... Back Page

TABLE DES MATIÈRES

****************

 Instructions importantes concernant

la sécurité .................................................. 2

 Symboles ................................................... 3

 Contenu de l’emballage .......................... 4-5

 Outils nécessaires ...................................... 5

 Fiche technique ......................................... 6

 Installation ............................................. 6-15

 Utilisation ............................................16-17

 Entretien ................................................... 18

 Dépannage ............................................... 19

 Garantie ................................................... 20

 Commande de pièces et

dépannage................................Page arrière

ÍNDICE DE CONTENIDO

****************

 Instrucciones de seguridad importantes ... 2

 Símbolos .................................................... 3

 Contenido del paquete ...........................4-5

 Herramientas necesarias ........................... 5

 Especificaciones del producto................... 6

 Instalación ............................................ 6-15

 Funcionamiento ..................................16-17

 Mantenimiento ......................................... 18

 Solución de problemas ............................ 19

 Garantía ................................................... 20

 Pedidos de piezas y

servicio ..................................Pág. posterior

INSTALLATION GUIDE

GUIDE D’INSTALLATION / GUÍA DE INSTALACIÓN

CF0110

CF0120

CF0130

CF0140

2 - English

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may

result in electric shock, fire and/or serious injury.

READ AND SAVE THESE INSTRUCTIONS



Use this unit only in the manner intended by the manu-

facturer. If you have questions, contact the manufacturer.



Before beginning installation, read and understand all

instructions and safety information. Thoroughly review

all assembly information and drawings and be sure you

understand the assembly requirements.



Before installing, servicing, or cleaning unit, switch power

off at service panel and lock the service disconnecting

means to prevent power from being switched on acci-

dentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

Installation and wiring must be in accordance with the

National Electrical Code, ANSI/NFPA 70 and all local

codes. If you are unfamiliar with or unable to comply with

these requirements, have ceiling fan installed by a licensed

electrician.

When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.



If this unit is to be installed over a tub or shower, it must

be marked as appropriate for the application and be

connected to a GFCI (Ground Fault Circuit Interrupter) —

protected branch circuit.

Do not bend the blade brackets when cleaning the fan. Do

not insert foreign objects in between rotating fan blades.

Mount ceiling fan directly to a structural framing member or

to a metal outlet box marked “Acceptable for Fan Support

of 35 lbs. or less. For outlet box mounting, use mounting

screws provided with the outlet box.

When using an existing outlet box, make sure it is securely

attached to the building structure and can support the full

weight of the fan. Most outlet boxes commonly used for

the support of lighting fixtures are not acceptable for fan

support and would therefore need to be replaced. Do not

use a plastic outlet box. Failure to follow this instruction

can result in serious injury or death.

To reduce the risk of injury to persons, install ceiling fan

so that the blade guard is at least 7 feet above the floor.



Ensure power is off before beginning installation. After

making the wire connections, wires should be spread

apart with the grounded conductor and the equipment-

grounding conductor on one side of the outlet box and

the ungrounded conductor on the other side of the outlet

box. Splices should be turned upward and pushed care-

fully up into the outlet box.



Always turn fan off and allow to come to a complete stop

before reversing blade direction.



When installation is complete, make sure all connections

are secure to prevent ceiling fan from falling.

Save these instructions. Refer to them frequently and

use them to instruct others who may use this product.

If you loan someone this product, loan them these

instructions also.

3 - English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation

of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

min Minutes Time

Alternating Current Type of current

n Rated Speed Maximum rotational speed

.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or serious

injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or seri-

ous injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or moder-

ate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but not

related to a potential injury (e.g. messages relating to property damage).

4 - English

HI

MED

LOW

OFF

PACKAGE CONTENTS

WARNING:

Items in this section are not assembled to the prod-

uct by the manufacturer and require installation.

Use of a product that may have been improperly

assembled could result in serious personal injury.

 Remove all parts from the package, and verify that

everything listed in this Package Contents section are

present.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call

1-877-258-9740 for assistance.

WARNING:

If any parts are damaged or missing, do not

operate this product until the parts are replaced.

Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this

product. Any such alteration or modification is

misuse and could result in a hazardous condition

leading to possible serious personal injury.

Part Description Quantity

1 Mounting bracket assembly* 1

2 Pivot ball/downrod assembly 1

3 Canopy* 1

4 Canopy screw cover ring* 1

5 Center arm support 1

6 Decorative legs 3

7 Motor housing cap 1

8 Fan assembly 1

9 Remote receiver 1

10 Remote control 1

11 Remote control wall mount 1

12 Remote control AAA batteries 2

13 Center arm support cover** 1

*For packing purposes, the mounting bracket assembly, canopy,

and canopy screw cover ring are assembled together.

**This part is used only if you install your ceiling fan using an

extended-length downrod longer than the one provided in this

package.

1

2

3

10

9

6

13

8

7

5

11

4

CEILING FAN PARTS AND ACCESSORIES

12

5 - English

PACKAGE CONTENTS

Part Description of Enclosed Installation Hardware Quantity

A Canada installation hardware bag 1

B Wire nuts 6

C Phillips cap screws 4

D Phillips cap screw covers 4

E Remote control wall mount screws 2

A

E

B

C

D

CEILING FAN HARDWARE

TOOLS NEEDED

Step ladder

Wire cutters/Strippers

LOOP

STRIP

WIREGAGE

PLERS

22

20

18

16

14

12

10

Phillips screwdriver

Adjustable wrench

Flat head screwdriver

6 - English

Speeds ............................................Hi - 1,400 r/min. (RPM)

Med - 940 r/min. (RPM)

Low - 500 r/min. (RPM)

Airflow (cubic feet per minute) .....................Hi - 1,437 CFM

Med - 830 CFM

Low - 445 CFM

Input ......................120 V, AC only, 60 Hz, 0.61 Amps Max.

Net Weight ................................................... approx. 24 lbs.

Ceiling Clearance Distance ......................................10.4 in.

Ceiling Mount Options............................. Angled, Standard

INSTALLATION

BEFORE YOU BEGIN

WARNING:

To reduce the risk of fire, electric shock, or

personal injury, turn off power to room and

wall switch by removing fuses or turning off

circuit breakers as needed before beginning

installation.

WARNING:

Mount fan only to a metal outlet box marked

acceptable for fan support and use only the

mounting screws provided with the outlet box.

Plastic outlet boxes and outlet boxes commonly

used for the support of lighting fixtures may not

be acceptable for fan support and may need to

be replaced. If you are unsure whether your outlet

box is appropriate or uncertain about the proper

method for mounting your ceiling fan, contact a

qualified electrician.

 If your installation site does not have an existing UL-listed

metal outlet box, one must be installed before proceed-

ing. Make sure box is mounted directly to the building

structure using ceiling joist screws provided with the box.

 Once installed, there must be at least 7 ft. clearance

between the bottom of the ceiling fan and the floor.

 Ceilings taller than 8 ft. may benefit from an extended-

length downrod (not included) to achieve the best results.

NOTE: Extended-length downrods longer than 48 in. will

also require a downrod wire extension kit (not included,

available from the retailer where you purchased your fan).

 Angled ceilings must not be steeper than 30˚ from the

horizontal canopy.

30˚ max.

CEILING

PRODUCT SPECIFICATIONS

7 - English

INSTALLATION

INSTALLING THE CEILING FAN MOUNTING

BRACKET ASSEMBLY

 The mounting bracket assembly, canopy, and the canopy

screw cover ring are assembled together for shipping

purposes. If you haven’t already done so, separate these

pieces now.

• Twist the canopy screw cover ring counterclockwise

to release.

• Loosen the two screws over the slots in the canopy.

• Remove the two screws securing the canopy to the

mounting bracket assembly, then twist the canopy

counterclockwise to release from the other two screws.

 Remove any existing ceiling fan or light where you intend

to install this ceiling fan. Verify the existing outlet box is

marked acceptable for fan support up to 35 lbs. and that

it is securely fastened to the ceiling joists.

CANOPY SCREW

COVER RING

CANOPY

MOUNTING

BRACKET

SCREW

For Canada installations, refer to the Canada

Installation Addendum located in the Canada

Installation Hardware Bag and install the eye

bolt or anchor assembly now.

 Using the screws provided with the outlet box, attach the

ceiling mounting bracket assembly to the electrical box,

passing the 120V electrical supply wires through the hole

in the center of the mounting bracket assembly.

NOTE:

If you are installing the mounting bracket assembly

for an angled orientation, make sure the open end of the

bracket is installed facing the lower point of the ceiling.

SCREW

SCREW OVER

CANOPY SLOT

SCREW OVER

CANOPY SLOT

OUTLET

BOX

CEILING

MOUNTING

BRACKET

ANGLED CEILING

OPEN END

FACING DOWN

ANGLED CEILING

8 - English

PREPARING YOUR CEILING FAN FOR

MOUNTING

 Loosen the screw securing the pivot ball to the downrod.

Slide the pivot ball down and off the downrod and set

aside.

 Remove the retainer pin from the downrod.

 Remove the screw and star washer securing the ground

wire terminal to the downrod. Remove the wire and set

aside.

INSTALLATION

 Loosen (but do not remove) the lock screws securing the

downrod to the mounting collar on the fan assembly, then

remove the hitch pin and the clevis pin from the mounting

collar. Carefully feed the fan’s electrical wiring up through

the threaded end of the downrod.

PIVOT BALL

DOWNROD

STAR WASHER

SCREW

GROUND WIRE

TERMINAL

RETAINER PIN

SCREW

CLEVIS PIN

MOUNTING COLLAR

DOWNROD

HITCH PIN

LOCK SCREW

DOWNROD

HOLE

LOCK SCREW

9 - English

INSTALLATION

DOWNROD HOLE

MOTOR HOUSING

HOLE

 Carefully feed the fan’s electrical wiring through the motor

housing cap, then install the cap as shown.

 Install the clevis pin through the holes in the motor hous-

ing and the downrod, then reinsert hitch pin. Retighten

the lock screws to secure.

LOCK SCREW

DOWNROD

MOTOR HOUSING CAP

 Thread the downrod into the motor housing until it bot-

toms out, then back it out until the hole in the downrod

aligns with the hole in the motor housing. Be careful not

to twist the electrical wiring when tightening.

 Carefully feed the fan’s electrical wiring through the center

arm support, then install the support with the cupped side

facing up.

NOTE: If you do not intend to use the decorative arms

supplied with this ceiling fan, you can skip this step

because the center arm support will not be needed.

However, if you are installing using an extended-length

downrod (not provided), you may still wish to use the

center arm support and the cover discussed in the next

step for a more finished appearance, even when not using

the decorative arms.

CUP SIDE UP

HITCH PIN

MOTOR HOUSING

CLEVIS PIN

LOCK SCREW

CENTER ARM

SUPPORT

10 - English

INSTALLATION

 Carefully feed the fan’s electrical wiring through the

canopy screw cover ring and canopy, then install the

cover ring and canopy on the downrod as shown.

NOTE: Make sure the notched openings on the rim of the

canopy screw cover ring are facing up.

CANOPY

CANOPY SCREW

COVER RING

NOTCHED

OPENINGS

This step is needed only if you are installing your

ceiling fan using an extended-length downrod

(not provided) and have installed the center arm

support from the previous step. If you are using

the downrod provided in this package, or if you

are using an extended-length downrod but chose

not to install the center arm support, skip this step

and proceed directly to installing the canopy screw

cover ring and canopy.

 Carefully feed the fan’s electrical wiring through the

center arm support cover, then install the support with

the cupped side facing down.

CUP SIDE DOWN

CENTER ARM

SUPPORT COVER

11 - English

ANGLED CEILING

INSTALLATION

 Carefully feed the fan’s electrical wiring through the pivot

ball, then reinstall the pivot ball on the downrod with the

flat side facing the ceiling.

 Reinstall the ground wire with the wire facing up to ensure

proper grounding, make sure the star washer is reinstalled

in the location shown below.

 Reinstall the retainer pin in the downrod.

For Canada installations, refer to the Canada

Installation Addendum and install the support

cable on the retainer pin now.

 Lift the pivot ball back to the top of the downrod until the

retainer pin is captured. Tighten the screw to secure.

NOTE: When the pivot ball is oriented correctly, it will

also cover the ground screw and will be flush with the

top of the downrod.

PIVOT BALL

FLAT SIDE UP

PIVOT BALL FLUSH WITH

TOP OF DOWNROD

DOWNROD

GROUND

SCREW

GROUND WIRE

STAR WASHER

RETAINER PIN

SCREW

For Canada installations, refer to the Canada

Installation Addendum and test the support

cable connection now.

12 - English

1

2

3

4

ON

DIP

 Verify the DIP switches on the receiver and the remote

control are both in the same configuration.

NOTE: The switches can be adjusted as needed to avoid

possible interference with other remote units in your

home, but always make sure that the same configuration

is set on both the remote and the receiver.

HANGING THE CEILING FAN

WARNING:

Once you begin the process of hanging the ceil-

ing fan, do not leave the fan unattended until the

installation process is complete. A falling fan

could cause serious personal injury or death.

 Carefully lift the assembled fan up to the mounting bracket

assembly and seat the pivot ball in the mounting bracket

socket. Rotate the fan as needed so the tab on the mount-

ing bracket socket seats in the groove in the pivot ball.

WARNING:

Failure to engage the fan’s tab into the groove

on the mounting bracket could allow the fan

to wobble and/or fall. A falling fan could cause

serious personal injury or death.

INSTALLATION

BACK SIDE OF

MOUNTING BRACKET

FRONT SIDE OF

MOUNTING BRACKET

PIVOT BALL

GROOVE

MOUNTING

BRACKET TAB

DIP SWITCH

ON

DIP

1 2

3

4

ON

E

1 2

3

4

C

E

REMOTE CONTROL

RECEIVER

13 - English

INSTALLATION

MAKING THE ELECTRICAL CONNECTIONS

WARNING:

Verify the power has been disconnected to both

the room and the wall switch before making the

electrical connections. Failure to do so could

cause fire, electric shock, serious personal injury,

or death.

NOTICE:

When shipped, the electrical wires from the ceiling

fan offer enough length to accommodate extended-

length downrods up to 48 in. (not included). For

shorter downrods, including the one provided

with this fan, this excess length is not needed

and should be cut off before making the electrical

connections in order to allow enough room for

everything to fit inside the mounting bracket. Trim

the electrical wires so that only 12 in. of electrical

wires extend from the top of the downrod. Failure

to trim the electrical wires as noted may make it

impossible to fit the receiver into the mounting

bracket as described in these instructions.

Connect the ceiling fan to the receiver:

 Connect the ceiling fan black wire to the black wire on

the receiver marked TO MOTOR L.

 Connect the ceiling fan white wire to the white wire on

the receiver marked TO MOTOR N.

 Connect the ceiling fan blue wire to the blue wire on the

receiver marked FOR LIGHT.

Connect the receiver to the 120V electrical supply wires:

 If your outlet box has a ground wire (green or bare cop-

per), connect it to the ground wire on the ceiling fan’s

pivot ball. If there is no ground wire in your outlet box,

connect the ground wire on the pivot ball to the ground

wire on the mounting bracket assembly.

 Connect the white (neutral) supply wire to the white wire

on the receiver marked AC in N.

 Connect the black (hot) supply wire to the black wire on

the receiver marked AC in L.

NOTE: If your electrical box has both red and black hot

wires, only one of these will be needed. Choose the sup-

ply wire that matches the wall switch you want to use for

your ceiling fan. Use a wire cap and electrical tape to seal

off the other wire and tuck it back up into the box and

out of the way.

 Install a plastic wire nut over each connection to secure.

Reinforce with electrical tape as needed to make sure

no bare wire is visible at the wire nuts (except for a bare

ground wire, if present).

ON

DIP

1 2

3

4

MOUNTING

BRACKET

GROUND

CONDUCTOR

BLACK

WHITE

GREEN/

YELLOW

GREEN/

YELLOW

WHITE

BLACK

WHITE

BLUE

RECEIVER

WIRE

NUT

 Spread the wires apart so the green/yellow and white

wires go to one side and the black and blue go to the

other, then carefully tuck all the wire connections up into

the outlet box.

NOTE: Orient the wires so the wire nuts are facing up

and are not touching each other. This will help minimize

potential noise once the installation is complete.

For Canada installations, refer to the Canada

Installation Addendum and connect the support

cable to the eye bolt or anchor assembly now.

14 - English

4

INSTALLATION

 Place the receiver into the top of the mounting bracket

with the flat side facing the ceiling. Tuck the receiver an-

tenna and all wiring up into the mounting bracket, making

sure the wires don’t become pinched.

 Slide the canopy up into place and rotate clockwise to lock

to mounting bracket assembly. Reinstall the two screws

(M4 x 6 mm) removed previously and tighten securely.

 Lift the screw cover ring up over the screws and twist

counterclockwise to secure in place.

CANOPY

SCREW

COVER RING

SCREWSSCREWS

CANOPY

SCREWS

CANOPY

SCREWS

MOUNTING

BRACKET

TOP VIEW

MOUNTING

BRACKET

RECEIVER

ANTENNA

TOP

SLIDES IN FROM THIS DIRECTION

15 - English

INSTALLATION

NOTICE:

The decorative arms in the next two steps are not

required for fan operation. You may skip these two

steps if you do not wish to install the decorative

arms.

 Install the decorative arms using a Phillips head screw-

driver. Attach one side of each arm to the center arm

support using the Phillips cap screws and screw covers

as shown.

NOTE: For easier assembly, insert each screw and par-

tially tighten, then go back and fully tighten each screw.

 Finish the assembly by screwing the finial screw on each

arm into the threaded holes in the top lens cover.

 Restore power to the room and wall switch. Turn on the

wall switch, then refer to the remote control operating

instructions in the next section to test the fan’s operation.

DECORATIVE ARM

SCREW

COVERS

CAP

SCREWS

FINIAL

SCREW

DECORATIVE ARM

16 - English

OPERATION

USING THE REMOTE CONTROL

NOTE: If you have not already done so, restore power to

the room and wall switch, then make sure the wall switch

controlling the fan is turned on. The remote control will have

no effect on the fan if the switch is turned off.

 Install the two AAA batteries provided into the remote

control.

To mount the remote control holder:

 Remove the screw cover from the remote control holder.

 Install the remote control holder in the desired location

using the two mounting screws provided.

 Replace the screw cover to cover the screw heads.

 To turn the light on and off, press and release the but-

ton. Press and hold the button to control the brightness

of the light.

NOTE: The brightness of the fan light can only be con-

trolled by the remote control. A wall-mounted dimmer

switch will not change the light’s brightness.

 To set the fan speed, press the desired speed button.

 To turn the fan OFF, press the OFF button.

HI

MED

LOW

OFF

ON

E

1 2

3

4

C

E

+ AAA 1.5V

AAA 1.5V +

AAA BATTERY

+

REMOTE CONTROL

BATTERY COVER

SCREWS

REMOTE CONTROL

HOLDER

SCREW COVER

MODEL NO: UC7216T

FCC ID: CHQ7216T

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this de-

vice must accept any interference received, including inter-

ference that may cause undesired operation.

17 - English

OPERATION

SETTING THE AIRFLOW DIRECTION

Choosing the correct airflow direction of the ceiling fan will

enhance the fan’s performance and make its use more en-

joyable. To change the direction of airflow, use the direction

switch on top of the ceiling fan’s housing.

NOTICE:

Always allow the ceiling fan to come to a complete

stop before changing the fan’s direction.

 Choose the DOWN position to provide a downward air

flow. In warmer weather, this direction will provide a con-

stant breeze, creating a wind chill effect for the room’s

occupants.

 In cooler weather, choose the UP position to provide an

upward direction of air travel. This will help circulate warm

air off the ceiling and back down into the room.

DIRECTION SWITCH

IN DOWN POSITION

DIRECTION SWITCH

IN UP POSITION

18 - English

MAINTENANCE

GENERAL CARE AND CLEANING

 Due to the natural movement of a ceiling fan, connections

can become loose over time. Check all the ceiling fan’s

connections (not including the electrical connections) at

least twice a year.

 The fan has permanently lubricated sealed bearings,

therefore no further lubrication is required.

 Clean your fan periodically to help maintain its new

appearance over time. Use only a soft brush or lint-free

cloth to avoid scratching the finish. The plating is sealed

with a lacquer to minimize discoloration or tarnishing. Do

not use water when cleaning, as this could damage the

motor or cause an electrical shock.

When shipped, the blade and guard on the ceiling fan are

preassembled. To diassemble for cleaning purposes:

WARNING:

Turn off power to room and wall switch by re-

moving fuses or turning off circuit breakers as

needed before disassembling the ceiling fan.

Failure to do so can cause serious personal injury.

 Remove the screws securing the decorative grill, then

remove the decorative grill.

 Remove the guard screws, then remove the blade guard.

 Remove the set screws at the top of the blade head using

a 3 mm hex wrench (not provided).

 Remove the blade from the motor shaft.

To reassemble the fan:

 Reinstall the blade on the motor shaft so the shaft opening

on the blade straddles the recessed area on the blade

shaft.

 Reinstall the set screws and tighten securely.

 Reinstall the blade guard and guard screws; tighten se-

curely.

 Reinstall the decorative grill and screws; tighten securely.

SCREW

COVERS

SCREWS

DECORATIVE

GRILL

BLADE GUARD

FAN

BLADE

SET

SCREWS

RECESSED AREA

ON MOTOR SHAFT

MOTOR SHAFT

HEX

WRENCH

19 - English

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE

Fan will not start. Wall switch is turned off. Turn wall switch on.

Circuit breaker is tripped or fuse is blown. Reset circuit breaker or replace fuse.

Ceiling fan wiring is incorrect. Check the ceiling fan’s electrical connections. If you are unable

to detect the problem, consult a qualified electrician.

Fan is noisy. Some noise is natural during the break-in period of the fan. Allow a minimum 24 hours

break-in period. Most noises associated with a new fan will be resolved during this time.

Ceiling fan housing screws are loose. Make sure all housing screws are snugly tightened.

Blade set screw is loose. Retighten the blade set screw.

Fan wobbles. Pivot ball is not captured in slot on fan mounting bracket. Refer to the instructions under

Hanging the Ceiling Fan on page 12 to be sure the ceiling fan is hung correctly.

Outlet box is not securely fastened to the ceiling joists. Tighten the outlet box screws or use

longer screws, if needed, to fasten securely.

Remote control is not

working.

Wall switch is turned off. Turn wall switch on.

Remote batteries are dead. Replace the batteries in the remote control.

Wall switch has solid-state speed controls. Do not use a wall switch that has variable speed

control (i.e. a dimmer switch).

DIP switches on the wall remote and the receiver do not match. Reset DIP switches so that

the configuration is the same on both the remote and the receiver.

Remote control and

fan are working, but

lights don’t work.

Verify the indicator light on the remote control lights up when you press the button. This

light indicates a signal is being sent from the remote control to the ceiling fan. If the indicator

light does not illuminate when the button is pressed, the remote control may be damaged and

need to be replaced. Contact a customer service representative.

If the light on the remote illuminates, but the lights on the fan still don’t work, contact a customer

service representative.

WARNING:

Turn off power to room and wall switch by removing fuses or turning off circuit breakers as needed before

attempting any repairs to the ceiling fan or the electrical connections. Failure to do so can cause serious

personal injury.

20 - English

WARRANTY

Limited Lifetime Warranty

WHAT THIS WARRANTY COVERS: For the original purchaser only, your Stile

™

ceiling fan motor is warranted to be free

of material and workmanship defects for the lifetime of the fan motor. All other ceiling fan parts are warranted to be free of

material and workmanship defects for a period of one year.

HOW TO GET SERVICE: To obtain replacement parts or servicing under warranty, please contact a service representative

at One World Technologies, Inc., 1428 Pearman Dairy Road, Anderson, SC 29625, by calling 1-877-258-9740, or by log-

ging on to www.TheStileLife.com. When you request warranty service, you must also present proof of purchase documen-

tation, which includes the date of purchase (for example, a bill of sale). We will repair any faulty workmanship, and either

repair or replace any defective part, at our option. We will do so without any charge to you.

WHAT’S NOT COVERED: This warranty applies only to the original purchaser at retail and may not be transferred. This

warranty does not cover any malfunction, failure, or defects resulting from misuse, abuse, normal wear and tear, neglect,

alteration, modification or repairs by other than Authorized Service Centers. This warranty does not cover any damage

caused by improper installation or the use of parts not provided or approved by the manufacturer for use with this fan. A

certain amount of “wobble” is normal and is not a defect. Due to varying climate conditions, this warranty does not cover

changes in the finish from rusting, pitting, tarnishing, corroding, or peeling. You should always protect the fan from varying

weather conditions.

All costs of removal and reinstallation are the express responsibility of the purchaser. One World Technologies, Inc., makes

no warranties, representations or promises as to the quality or performance of its products other than those specifically

stated in this warranty.

ADDITIONAL LIMITATIONS: Any implied warranties granted under state law, including warranties of merchantability or

fitness for a particular purpose, are limited to the terms stated above. One World Technologies, Inc. is not responsible for

direct, indirect, or incidental damages, so the above limitations and exclusions may not apply to you. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state.

CUSTOMER SERVICE INFORMATION:

For parts or service, or access to an Authorized Service Center, please call 1-877-258-9740 or visit us online at

www.TheStileLife.com.

The model number and serial number of this ceiling fan is found on a label located on the top of the fan housing. Please

record the serial number in the space provided below. When calling about warranty service or if ordering repair parts, always

give the following information:

Model No. ______________________________________ Serial No. ____________________________________________

La page charge ...

Stile CF0130 Mode d'emploi

Ce manuel convient également à

Stile CF0130 Mode d'emploi

dans d''autres langues

Autres documents