MTD 705r Le manuel du propriétaire

Catégorie
Coupe-herbe
Taper
Le manuel du propriétaire
2-Cycle Gas Trimmer
OPERATOR’S MANUAL
FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or
1-800-668-1238 in CANADA
www.RyobiOutdoor.com
IMPORTANT MANUAL DO NOT THROW AWAY
705r
THANK YOU
Thank you for buying this quality product. This modern
outdoor power tool will provide many hours of useful
service. You will find it to be a great labor-saving device.
This operator’s manual provides you with easy-to-
understand operating instructions. Read the whole
manual and follow all the instructions to keep your new
outdoor power tool in top operating condition.
PRODUCT REFERENCES, ILLUSTRATIONS
AND SPECIFICATIONS
All information, illustrations and specifications in this
manual are based on the latest product information
available at the time of printing. We reserve the right to
make changes at any time without notice.
Copyright
©
2003 MTD SOUTHWEST INC
All Rights Reserved.
SpeedSpool is a registered trademark of MTD
SOUTHWEST INC.
SERVICE INFORMATION
Service on this unit both within and after the warranty
period should be performed only by an authorized and
approved service dealer.
Call 1-800-345-8746 in the United States, or
1-800-668-1238 in Canada, to obtain a list of
authorized service dealers near you
Or
Go to www.RyobiOutdoor.com on the World Wide
Web for a list of authorized service dealers
DO NOT RETURN THE UNIT TO THE RETAILER.
NOTE: PROOF OF PURCHASE WILL BE REQUIRED
FOR WARRANTY SERVICE.
Make sure you carefully read and understand this
manual before starting or operating this equipment.
THIS PRODUCT IS COVERED BY ONE OR MORE
US PATENTS, OTHER PATENTS PENDING.
2
INTRODUCTION TABLE OF CONTENTS
I. California Proposition 65 Warning . . . . . . . . . . . . . . . . 3
II. Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . 3-7
A. Important Safety Information . . . . . . . . . . . . . . . . . 4
B. Safety and International Symbols . . . . . . . . . . . . . . 6
C. Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
III. Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 8
A. Installing and Adjusting the D-Handle . . . . . . . . . . 8
B. Installing the Cutting Attachment Shield . . . . . . . . 8
IV. Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . 9
V. Starting/Stopping Instructions . . . . . . . . . . . . . . . . . 10
VI. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . 11
A. Holding the Trimmer . . . . . . . . . . . . . . . . . . . . . . . 11
B. Adjusting Trimming Line Length . . . . . . . . . . . . . . 11
C. Tips for Best Trimming Results . . . . . . . . . . . . . . 11
D. Decorative Trimming . . . . . . . . . . . . . . . . . . . . . . . 11
VII. Maintenance and Repair Instructions . . . . . . . . . 12-18
A. Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . 12
B. Line Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
C. Installing a Pre-wound Wheel . . . . . . . . . . . . . . . .13
D. Cleaning the SpeedSpool . . . . . . . . . . . . . . . . . . . 14
E. Air Filter Maintenance . . . . . . . . . . . . . . . . . . . . . . 15
F. Spark Arrestor Maintenance . . . . . . . . . . . . . . . . . 16
G. Carburetor Adjustment . . . . . . . . . . . . . . . . . . . . . 17
H. Replacing the Spark Plug . . . . . . . . . . . . . . . . . . . 17
I. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
J. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
K. Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 18
L. Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
M.Accessories/Replacement Parts . . . . . . . . . . . . . . 18
VIII.Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . 19
IX. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
X. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
XI. Parts List . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover
CONTENTS OF CARTON
•Model 705r Trimmer with SpeedSpool
®
Bump Head
Cutting Attachment
D-Handle and Hardware
Cutting Attachment Shield with Hardware
•Operator's Manual
Product Registration Card
Bottle of 2-Cycle Oil
This item will either be installed on the unit or in the
hardware pack
3
NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S.
Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by
law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a
spark arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the
prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to
follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If
it requires replacement, ask your LOCAL SERVICE DEALER to install the Accessory Part #182747 Spark Arrestor Kit.
Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so
can result in serious injury to the operator and/or bystanders.
FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-668-1238 in CANADA
SPARK ARRESTOR
WARNING!
RULES FOR SAFE OPERATION
CALIFORNIA PROPOSITION 65 WARNING
WARNING
THE ENGINE EXHAUST FROM THIS
PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER, BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
DANGER: Failure to obey a safety warning
will result in serious injury to yourself or to
others. Always follow the safety
precautions to reduce the risk of fire,
electric shock and personal injury.
WARNING: Failure to obey a safety
warning can result in injury to yourself and
others. Always follow the safety
precautions to reduce the risk of fire,
electric shock and personal injury.
CAUTION: Failure to obey a safety warning
may result in property damage or personal
injury to yourself or to others. Always follow
the safety precautions to reduce the risk of
fire, electric shock and personal injury.
SAFETY ALERT SYMBOL: Indicates
danger, warning or caution. Attention is
required in order to avoid serious personal
injury. May be used in conjunction with
other symbols or pictographs.
SYMBOL MEANING
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
NOTE: Advises you of information or instructions vital
to the operation or maintenance of the
equipment.
SYMBOL MEANING
4
READ ALL INSTRUCTIONS
BEFORE OPERATING
Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
Do not operate this unit when tired, ill or under the
influence of alcohol, drugs or medication.
Children under the age of 15 must not use the unit;
teens may operate the unit with adult guidance.
Inspect the unit before use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in
place and secure. Replace cutting attachment parts
that are cracked, chipped or damaged in any way.
Make sure the cutting attachment is properly installed
and securely fastened. Be sure that the cutting
attachment shield is properly attached, and positioned
as recommended. Failure to do so can result in
personal injury to the operator and bystanders, as well
as damage to the unit.
Use only 0.080 inch (2.03 mm) diameter Genuine
Factory Parts™ replacement line. Never use metal-
reinforced line, wire, chain or rope. These can break
off and become dangerous projectiles.
Be aware of risk of injury to the head, hands and feet.
Clear the area to be cut before each use. Remove
rocks, broken glass, nails, wire, string and other
objects which may be thrown or become entangled in
the cutting attachment. Clear the area of children,
bystanders and pets; keep them outside a 50-foot
(15 m.) radius, at a minimum. Even then, they are still
at risk from thrown objects. Encourage bystanders to
wear eye protection. If you are approached, stop the
unit immediately.
Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments
or repairs before using the unit.
This unit was not designed to be used as a brushcutter.
Do not attach or operate this unit with any type of
brushcutting blade or brushcutting attachment.
• IMPORTANT SAFETY INFORMATION •
SAFETY WARNINGS FOR GAS TRIMMERS
Store fuel only in containers specifically designed and
approved for the storage of such materials.
Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the fuel tank cap or
add fuel when the engine is hot. Never operate the unit
without the fuel cap securely in place. Loosen the fuel
tank cap slowly to relieve any pressure in the tank.
Add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. Remove the fuel cap
slowly, and only after the engine stops. Do not smoke
while fueling or mixing fuel. Wipe up any spilled fuel
from the unit immediately.
Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke. Keep sparks and open flames away from the
area while adding fuel or operating the unit.
WHILE OPERATING
Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can be fatal.
Operate this unit only in a well-ventilated outdoor area.
Wear safety glasses or goggles that meet ANSI Z87.1
standards and are marked as such. Wear ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty.
Wear heavy long pants, boots, gloves and a long
sleeve shirt. Do not wear loose clothing, jewelry, short
pants, sandals or go barefoot. Secure hair above
shoulder level.
The cutting attachment shield must always be in place
while operating the unit. Do not operate unit without
both trimming lines extended, and the proper line
installed. Do not extend the trimming line beyond the
length of the shield.
This unit has a clutch. The cutting attachment remains
stationary when the engine is idling. If it does not, have
the unit adjusted by an authorized service technician.
Adjust the D-handle to your size in order to provide the
best grip.
Be sure the cutting attachment is not in contact with
anything before starting the unit.
Use the unit only in daylight or good artificial light.
WARNING
:
When using the unit, you must
follow the safety rules. For your own safety
and that of bystanders, please read these
instructions before operating the unit.
Please keep the instructions for later use.
WARNING
:
Gasoline is highly flammable,
and its vapors can explode if ignited. Take
the following precautions:
RULES FOR SAFE OPERATION
5
Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and
unit must be in a stable position while starting. Refer
to Starting/Stopping Instructions.
Use the right tool. Only use this tool for its intended
purpose.
Do not overreach. Always keep proper footing and
balance.
Always hold the unit with both hands when operating.
Keep a firm grip on both handles or grips.
Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the cutting
attachment when it rotates.
Do not touch the engine, gear housing or muffler.
These parts get extremely hot from operation, even
after the unit is turned off.
Do not operate the engine faster than the speed
needed to cut, trim or edge. Do not run the engine at
high speed when not cutting.
Always stop the engine when cutting is delayed or
when walking from one cutting location to another.
If you strike or become entangled with a foreign
object, stop the engine immediately and check for
damage. Do not operate before repairing damage. Do
not operate the unit with loose or damaged parts.
Stop the unit, switch the engine to off, and disconnect
the spark plug for maintenance or repair.
Use only Genuine Factory Parts™ replacement parts
and accessories for this unit. These are available from
your authorized service dealer. Use of any
unauthorized parts or accessories could lead to
serious injury to the user, or damage to the unit, and
void your warranty.
Keep unit clean of vegetation and other materials.
They may become lodged between the cutting
attachment and shield.
To reduce fire hazard, replace a faulty muffler and
spark arrestor. Keep the engine and muffler free from
grass, leaves, excessive grease or carbon build up.
OTHER SAFETY WARNINGS
Never store a fueled unit inside a building where fumes
may reach an open flame or spark.
Allow the engine to cool before storing or transporting.
Be sure to secure the unit while transporting.
Store the unit in a dry area, locked up or up high to
prevent unauthorized use or damage, out of the reach
of children.
Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use, see Cleaning and Storage
instructions.
Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
SAVE THESE INSTRUCTIONS
RULES FOR SAFE OPERATION
6
RULES FOR SAFE OPERATION
SYMBOL MEANING
SAFETY ALERT SYMBOL
Indicates danger, warning, or
caution. May be used in conjunction
with other symbols or pictographs.
WARNING - READ OPERATOR'S
MANUAL
Read the Operator’s Manual(s) and
follow all warnings and safety
instructions. Failure to do so can
result in serious injury to the
operator and/or bystanders.
WEAR EYE AND HEARING
PROTECTION
WARNING: Thrown objects and
loud noise can cause severe eye
injury and hearing loss. Wear eye
protection meeting ANSI Z87.1-1989
standards and ear protection when
operating this unit.
Use a full face
shield when needed.
KEEP BYSTANDERS AWAY
WARNING: Keep all bystanders,
especially children and pets, at least
50 feet (15 m.) from the operating area.
UNLEADED FUEL
Always use clean, fresh unleaded fuel.
OIL
Refer to operator's manual for the
proper type of oil.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
THROWN OBJECTS AND
ROTATING CUTTER CAN CAUSE
SEVERE INJURY
WARNING
:
Do not operate without
the cutting attachment shield in
place. Keep away from the rotating
cutting attachment.
•ON/OFF STOP CONTROL
ON / START / RUN
•ON/OFF STOP CONTROL
OFF or STOP
HOT SURFACE WARNING
Do not touch a hot muffler or
cylinder. You may get burned. These
parts get extremely hot from
operation. When turned off they
remain hot for a short time.
SHARP BLADE
WARNING: Sharp blade on cutting
attachment shield. To prevent
serious injury, do not
touch line cutting blade.
CHOKE CONTROL
A • FULL choke position
B •
PARTIAL choke position
C •
RUN position
7
RULES FOR SAFE OPERATION
APPLICATIONS
As a trimmer:
Cutting grass and light weeds
Edging
Decorative trimming around trees, fences, etc.
KNOW YOUR UNIT
Cutting Attachment
Shield
Fuel Cap
Throttle
Control
Cutting Attachment
Shaft Grip
Primer Bulb
Choke Lever
Air Filter/Muffler
Cover
Spark Plug
On/Off Stop Control
Shaft
Housing
Starter Rope Grip
Line Cutting Blade
Muffler
D-handle
8
ASSEMBLY INSTRUCTIONS
Fig. 2
INSTALL AND ADJUST THE D-HANDLE
1. Push the D-handle down onto the shaft housing so
that the handle slants towards the shaft grip (Fig. 1).
The squared bolt hole in the handle is to the right.
2. Insert the shoulder bolt into the squared hole in the
handle and push through. On the left side of the
handle, place the washer on the bolt, then screw the
wing nut onto the bolt. Do not tighten until you make
the handle adjustment.
3. Rotate the D-handle to place the grip above the top
of the shaft housing. Place it a minimum of 6 inches
(15.24 cm) from the end of the shaft grip.
4. While holding the unit in the operating position
(Fig. 2), position the D-handle to the location that
provides you the best grip.
5. Tighten the wing nut until the D-handle is secure.
Fig. 1
Bolt
Washer
Wing Nut
Tighten
Shaft Grip
D-Handle
Minimum 6 inches
(15.24 cm)
Shaft Housing
INSTALL THE CUTTING ATTACHMENT SHIELD
Use the following instructions if the cutting attachment
shield on your unit is not installed.
1. Place the cutting attachment shield onto the shaft
housing above the clamp assembly (Fig. 3).
2. Push the cutting attachment shield down to the top of
the cutting attachment assembly and then rotate the
cutting attachment shield until the screw holes align
and the guard fits into the recessed pocket (Fig. 4).
3. Install the screws with a Phillips screwdriver (Fig. 5).
WARNING: To prevent serious personal
injury, never operate the trimmer without
the cutting attachment shield in place.
Fig. 3
Fig. 4
Shaft Housing
(4) Screws
Clamp
Assembly
Cutting
Attachment
Assembly
Cutting Attachment
Shield
Recessed
Pocket
Fig. 5
9
OIL AND FUEL INFORMATION
NOTE: Dispose of the old fuel/oil mix in accordance to
Federal, State and Local regulations.
CAUTION: For proper engine operation and
maximum reliability, pay strict attention to
the oil and fuel mixing instructions on the
2-cycle oil container. Using improperly
mixed fuel can severely damage the engine.
WARNING: Gasoline is extremely
flammable. Ignited Vapors may explode.
Always stop the engine and allow it to cool
before filling the fuel tank. Do not smoke
while filling the tank. Keep sparks and open
flames at a distance from the area.
WARNING: Remove fuel cap slowly to avoid
injury from fuel spray. Never operate the unit
without the fuel cap securely in place
.
WARNING: Add fuel in a clean, well
ventilated area outdoors. Wipe up any
spilled fuel immediately. Avoid creating a
source of ignition for spilt fuel. Do not start
the engine until fuel vapors dissipate.
OIL AND FUEL MIXING INSTRUCTIONS
Old and/or improperly mixed fuel are the main reasons
for the unit not running properly. Be sure to use fresh,
clean unleaded fuel. Follow the instructions carefully for
the proper fuel/oil mixture.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and
oxygenates such as ethanol, methanol, or MTBE (ether).
Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate. It forms
acids when stored. When using alcohol-blended fuel,
use fresh fuel (less than 60 days old).
Using Blended Fuels
If you choose to use a blended fuel, or its use is
unavoidable, follow recommended precautions:
Always use the fresh fuel mix explained in your
operator's manual
Always agitate the fuel mix before fueling the unit
Drain the tank and run the engine dry before storing
the unit
Using Fuel Additives
The bottle of 2-cycle oil that came with your unit
contains a fuel additive which will help inhibit corrosion
and minimize the formation of gum deposits. It is
recommended that you use our 2-cycle oil with this unit.
If unavailable, use a good 2-cycle oil designed for
air-cooled engines along with a fuel additive, such as
STA-BIL
®
Gas Stabilizer or an equivalent. Add 0.8 oz.
(23 ml.) of fuel additive per gallon of fuel according to the
instructions on the container. NEVER add fuel additives
directly to the unit's fuel tank.
Thoroughly mix the proper ratio of 2-cycle engine oil
with unleaded gasoline in a separate fuel can. Use a 40:1
fuel/oil ratio. Do not mix them directly in the engine fuel
tank. See the table below for specific gas and oil mixing
ratios.
NOTE: One gallon (3.8 liters) of unleaded gasoline mixed
with one 3.2 oz. (95 ml.) bottle of
2-cycle oil makes a 40:1 fuel/oil ratio.
+
UNLEADED GAS 2 CYCLE OIL
1 US. GALLON + 3.2 FL. OZ.
(3.8 LITERS) (95 ml)
1 LITER + 25 ml
MIXING RATIO - 40:1
10
STARTING INSTRUCTIONS
1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.
Refer to Oil and Fuel Mixing Instructions.
2. Put the On/Off Stop Control in the ON (I) position
(Fig. 6).
3. Fully press and release the primer bulb 10 times,
slowly, until FUEL IS VISIBLE IN THE PRIMER
BULB (Fig. 7). If you can’t see fuel in the bulb, press
and release the bulb as many times as it takes before
you can see fuel in it.
4. Place the choke lever in the FULL choke (A )
position (Fig. 7).
5. With the unit in the starting position (Fig. 8), squeeze
the throttle control to the wide open (full throttle)
position. Pull the starter rope briskly 5 times while still
in the FULL choke (A ) position. If the engine
attempts to run before the fifth pull, proceed to step 6.
NOTE: The engine will not run in the FULL choke (A )
position.
6. Place the choke lever in the PARTIAL choke (B )
position (Fig. 7).
7. Pull starter rope briskly 1 to 3 times to start the
engine (Fig. 8).
NOTE: Squeeze the throttle control until the engine has
started and warmed up.
8. If the engine does not start, repeat steps 3 through 7.
NOTE: If the engine floods while trying to start, place the
choke lever in the RUN (C ) position (Fig. 7).
Squeeze the throttle control. Pull the starter rope
briskly. The engine should start within three (3) to
eight (8) pulls.
9. Squeeze the throttle control to warm up the engine
for 5 to 10 seconds. Place the choke lever in the
RUN (C ) position (Fig. 7).
NOTE: Choking is unnecessary when starting a warm
engine. Put the On/Off Stop Control in the ON
position (Fig. 6), and start in PARTIAL choke
(B ) position (Fig. 7). After starting, place the
choke lever in the RUN (C ) position.
WARNING:
Operate this unit only in a well-
ventilated outdoor area. Carbon monoxide
exhaust fumes can be lethal in a confined area.
WARNING: Avoid accidental starting. Make
sure you are in the starting position when
pulling the starter rope (Fig. 8).
To avoid
serious injury, the operator and unit must be
in a stable position while starting.
STARTING/STOPPING INSTRUCTIONS
Fig. 8
Starter Rope
Throttle Control
STOPPING INSTRUCTIONS
1. Release your hand from the throttle control (Fig. 8).
Allow the engine to cool down by idling.
2. Put the On/Off Stop Control in the OFF (O) position
(Fig. 6).
Fig. 6
On/Off Stop Control
Start/On (I)
Stop/Off (O)
Choke Lever
Full Choke
Position (A)
Run
Position (C)
Partial Choke
Position (B)
Primer Bulb
Fig. 7
11
OPERATING INSTRUCTIONS
NOTE: Do not rest the Bump Head™ on the ground
while the unit is running.
Some line breakage will occur from:
Entanglement with foreign matter
Normal line fatigue
Attempting to cut thick, stalky weeds
Forcing the line into objects such as walls or fence posts
TIPS FOR BEST TRIMMING RESULTS
Keep the cutting attachment parallel to the ground.
Do not force the cutting attachment. Allow the tip of the
line to do the cutting, especially along walls. Cutting with
more than the tip will reduce cutting efficiency and may
overload the engine.
Cut grass over 8 inches (200 mm) by working from top
to bottom in small increments to avoid premature line
wear or engine drag.
Cut from right to left whenever possible. Cutting to the left
improves the unit's cutting efficiency. Clippings are
thrown away from the operator.
Slowly move the trimmer into and out of the cutting
area at the desired height. Move either in a forward-
backward or side-to-side motion. Cutting shorter
lengths produces the best results.
Trim only when grass and weeds are dry.
The life of your cutting line is dependent upon;
• Adherence of the listed trimming techniques
• What vegetation is cut
• Where vegetation is cut
For example, the line will wear faster when trimming against
a foundation wall as opposed to trimming around a tree.
HOLDING THE TRIMMER
Before operating the unit, stand in the operating position
(Fig. 9). Check for the following:
The operator is wearing eye protection and proper
clothing
With a slightly-bent right arm, the operator’s right hand
is holding the shaft grip
The operator’s left arm is straight, the left hand holding
the D-handle
The unit is at waist level
The cutting attachment is parallel to the ground and
easily contacts the grass without the need to bend ove
r
Fig. 9
ADJUSTING TRIMMING LINE LENGTH
The Bump Head™ cutting attachment allows you to
release trimming line without stopping the engine. To
release more line, lightly tap the cutting attachment on the
ground (Fig. 10) while operating the trimmer at high speed.
NOTE: Always keep the trimming line fully extended.
Line release becomes more difficult as cutting
line becomes shorter
Fig. 10
CAUTION:
Do not remove or alter the line
cutting blade assembly. Excessive line length
will make the clutch overheat. This may lead to
serious personal injury or damage to the unit.
WARNING: Always wear eye, hearing, foot
and body protection to reduce the risk of
injury when operating this unit.
Each time the head is bumped, about 1 inch (25.4 mm)
of trimming line releases. A blade in the cutting
attachment shield will cut the line to the proper length if
any excess line is released.
For best results, tap the bump knob on bare ground or
hard soil. If you attempt a line release in tall grass, the
engine may stall. Always keep the trimming line fully
extended. Line release becomes more difficult when the
cutting line gets shorter.
DECORATIVE TRIMMING
Decorative trimming is accomplished by removing all
vegetation around trees, posts, fences, etc.
Rotate the whole unit so that the cutting attachment is at
a 30° angle to the ground (Fig. 11).
Fig. 11
12
MAINTENANCE SCHEDULE
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should
also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require
special tools or skills. If you are unsure about
these procedures take your unit to any non-road
engine repair establishment, individual or
authorized service dealer.
NOTE: Maintenance, replacement, or repair of the
emission control devices and system may be
performed by any non-road engine repair
establishment, individual or authorized service
dealer.
In order to assure peak performance of your engine,
inspection of the engine exhaust port may be necessary
after 50 hours of operation. If you notice lost RPM, poor
performance or general lack of acceleration, this service
may be required. If you feel your engine is in need of this
inspection, refer service to any non-road engine repair
establishment, individual or authorized service dealer for
repair. DO NOT attempt to perform this process yourself
as engine damage may result from contaminants
involved in the cleaning process for the port.
FREQUENCY MAINTENANCE REQUIRED REFER TO
Before starting engine Fill fuel tank with fresh fuel Page 9
Every 10 hours Clean and re-oil air filter Page 15
Every 25 hours
Check and clean spark arrestor
Check spark plug condition and gap
Page 16
Page 17
Every 50 hours
Inspect exhaust port and spark arrestor screen for clogging or
obstruction to assure maximum performance levels
Page 16
MAINTENANCE AND REPAIR INSTRUCTIONS
WARNING: To prevent serious injury, never
perform maintenance or repairs with unit
running. Always service and repair a cool unit.
Disconnect the spark plug wire to ensure that
the unit cannot start.
LINE INSTALLATION FOR THE SPEEDSPOOL
®
Always use Genuine Factory Parts™ 0.080 inch (2.03
mm) replacement line. Lines other than those specified
may make the engine overheat or fail.
There are two methods to replace the SpeedSpool
®
trimming line:
• Wind the inner reel with new line
• Install a pre-wound inner reel
Winding the Inner Reel With New Line
NOTE: It Is unnecessary to remove the bump knob to
install a new trimming line.
1. Cut two pieces of 0.080 inch (2.03 mm) trimming
line, 10 feet (3 m) long.
2. Hold the outer spool and turn the inner reel
counterclockwise to line up the arrows on the outer
spool and inner reel (Fig. 12).
Top View Of The SpeedSpool
®
Outer Spool
Inner Reel
Fig. 12
Bump Knob
Arrows
WARNING: Always use the correct line
length when installing trimming line on the
unit. The line may not release properly if the
line is too long.
WARNING: Never use metal-reinforced
line, wire, chain or rope. These can break
off and become dangerous projectiles.
13
MAINTENANCE AND REPAIR INSTRUCTIONS
Line Locking Hole
Trimming Line
Line Loading Hole
Eyelet
5. Insert the line into the locking hole (Fig. 14). Do not
push the line more than a 1/2 inch (12.7 mm) into the
line locking hole. The line will form a small loop
(Fig. 14) when it is inserted correctly.
3. Pull old line out of the line loading and line locking
holes (Fig. 13 and 14).
4. Insert a piece of trimming line straight into one of the
two eyelets in the outer spool. Push it up through the
line loading hole in the inner reel (Fig. 13). Do not
bend the line when inserting it into the eyelet.
Fig. 13
Fig. 14
6. Pull the line from the outer spool until the line is tight
against the inner reel (Fig. 15).
Fig. 15
INSTALLING A PRE-WOUND REEL
1. Turn the bump knob counterclockwise and remove
the bump knob, spring and foam seal (Fig. 18).
9. If winding the line becomes difficult or if the line
jams, pull the ends of the line from the spool
(Fig. 17). Continue winding the inner reel
counterclockwise.
Fig. 16
Fig. 17
7. Repeat procedures 4-6 with the second piece of line.
8. Hold the outer spool. Wind the inner reel
counterclockwise until approximately four (4) inches
(102 mm) of line remain (Fig. 16).
NOTE: Do not wind the inner reel before installing the
second piece of line.
Bump Knob
Foam Seal
Spring
Inner Reel
Fig. 18
14
MAINTENANCE AND REPAIR INSTRUCTIONS
SPEEDSPOOL
®
REPLACEMENT PARTS
Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472
Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460
Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465
Foam Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181467
Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464
Bump Knob Assembly . . . . . . . . . . . . . . . . . . . . 181468
These SpeedSpool
®
replacement parts can be
purchased from your local authorized dealer.
4. Hold the inner reel in place and install the bump
knob, spring and foam seal. Press down and turn the
bump knob clockwise. Grasp the ends and pull
firmly to release the line from the holding slots in the
inner reel (Fig. 18).
Releasing the Inner Reel
If the SpeedSpool
®
does not release line correctly, pull
the ends of the line firmly from the spool (Fig. 17). If this
does not the release line, follow the Cleaning the
SpeedSpool
®
instructions.
2. Pull the old inner reel with existing line from the outer
spool.
3. Insert the ends of the prewound inner reel line into
the outer spool eyelets (Fig. 19). Push the new inner
reel, arrow side up, into the outer spool.
Fig. 19
4. Remove any existing line from the inner reel before
cleaning. Remove any debris or grass from the knob,
spring, inner reel and foam seal. Wash the inner reel
with warm soapy water (Fig. 21).
Fig. 20
CLEANING THE SPEEDSPOOL
®
Cleaning the SpeedSpool
®
may be necessary if:
•A jammed or excessive line must be removed
The SpeedSpool
®
becomes difficult to wind or does
not operate correctly when bumping the head on the
ground
1. Hold the outer spool, and unscrew the bump knob
counterclockwise (Fig. 20).
2. Pull out the bump knob, spring and foam seal (Fig. 18).
Shaft
Plunger
NOTE: The inner reel must be totally dry before
reinstalling it into the outer spool. Do not lubricate
the inner reel or outer spool assembly.
6. Place the inner reel into the outer spool.
7. Place the bump knob, spring and foam seal into the
inner reel (Fig. 18).
8. Press the bump knob down and tighten clockwise.
9. Install new line as described in Line Installation for
the SpeedSpool
®
.
5. Clean the shaft and the inner surface of the outer
spool. To clean the shaft underneath the plunger,
press down on the plunger (Fig. 22). Remove any dirt
or debris from the shaft.
Fig. 22
Inner Reel
Fig. 21
3. Pull the inner reel with existing line from the outer
spool (Fig. 19).
15
MAINTENANCE AND REPAIR INSTRUCTIONS
AIR FILTER MAINTENANCE
Removing the Air Filter/Muffler Cover
1.
Place the choke lever in the PARTIAL choke position (B).
NOTE: The choke lever must be in the PARTIAL choke
position (B) to remove the air filter/ muffler cover.
2. Remove the four (4) screws securing the air
filter/muffler cover (Fig. 23). Use a flat blade or
T-20 Torx bit screwdriver.
3. Pull the cover from the engine. Do not force.
WARNING: To avoid serious personal injury,
always turn your trimmer off and allow it to
cool before you clean or service it.
Cleaning the Air Filter
Clean and re-oil the air filter every 10 hours of operation.
It is an important item to maintain. Failure to maintain the
air filter will VOID the warranty.
1. Remove air filter/muffler cover. Refer to Removing
the Air Filter/Muffler Cover.
2. Turn cover over and look inside to locate the air filter.
Remove the air filter from inside the air filter/muffler
cover (Fig. 24).
3. Wash the filter in detergent and water (Fig. 25). Rinse
the filter thoroughly. Squeeze out excess water. Allow
it to dry completely.
4. Apply enough clean SAE 30 oil to lightly coat the filter
(Fig. 26).
5. Squeeze the filter to spread and remove excess oil
(Fig. 27).
Fig. 24
Fig. 25
Fig. 26
Fig. 27
6. Replace the air filter inside the air filter/muffler cover
(Fig. 24).
NOTE: Operating the unit without the air filter and air
filter/muffler cover assembly will VOID the
warranty.
Reinstalling the Air Filter/Muffler Cover
1. Place the air filter/muffler cover over the back of the
carburetor and muffler. Align the screw holes.
2. Insert the four (4) screws into the holes in the air
filter/muffler cover (Fig. 23) and tighten.
Do not over tighten.
Air Filter
Inside Muffler
Cover
Choke Lever
Screws
Screws
Partial Choke
Position (B)
Fig. 23
16
SPARK ARRESTOR MAINTENANCE
1. Remove air filter/muffler cover. Refer to Removing
the Air Filter/Muffler Cover.
2. Locate muffler front and the two (2) bolts securing it
to the engine (Fig. 28). Remove the two (2) bolts
using a flatblade screwdriver or 5/16-inch socket or
nut driver. Pull muffler off of the engine.
3. Turn muffler over to the back side and locate the
exhaust gasket. Remove the muffler gasket from the
muffler (Fig. 28).
NOTE: If the exhaust gasket is torn or damaged, replace
it with a new gasket before reassembling muffler.
4. Using a small flatblade screwdriver, carefully pry up
the spark arrestor from the recessed hole (Fig. 29).
Remove the spark arrestor from the muffler.
5. Clean the spark arrestor with a wire brush. Replace it
if it is damaged or if it is impossible to clean
thoroughly (Fig. 29).
6. Reinstall the spark arrestor by pressing it into the
recessed hole on the muffler's back side. Make sure
it fits tightly against the muffler and is not raised up.
7. Place the exhaust gasket against muffler's back side.
Align the gasket bolt holes with the bolt holes in the
muffler. While holding exhaust gasket in place, insert
the bolts into the muffler's front side (Fig. 28).
8. Place the muffler (with the exhaust gasket in place
and bolts inserted), against the engine, aligning the
bolt holes. Tighten the bolts to secure the muffler to
the engine.
If using a torque wrench, torque to:
80-90 in.•lb. (9-10.2 N•m)
9. Reinstall the air filter/muffler cover.
Fig. 29
Fig. 28
Muffler - Front Side
Muffler - Back Side
Bolts
Exhaust
Gasket
Spark
Arrestor
Muffler - Back Side
Spark
Arrestor
Flatblade
Screwdriver
Spark Arrestor
WARNING:
If the muffler is not tightened
securely, it could fall off causing damage to
the unit and possible serious personal injury
MAINTENANCE AND REPAIR INSTRUCTIONS
17
Check Fuel Mixture
Old and/or improperly mixed fuel is usually the reason
for improper unit performance. Drain and refill the tank
with fresh, properly-mixed fuel prior to making any
adjustments. Refer to Oil and Fuel Information.
Clean Air Filter
The condition of the air filter is important to the operation
of the unit. A dirty air filter will restrict air flow and
change the air/fuel mixture. This is often mistaken for an
out of adjustment carburetor. Check the condition of the
air filter before adjusting the idle speed screw. Refer to
Air Filter Maintenance.
Adjust Idle Speed Screw
If, after checking the fuel mixture and cleaning the air
filter, the engine still will not idle, adjust the idle speed
screw as follows:
1. Start the engine and let it run at a high idle for a
minute to warm up. Refer to Starting/Stopping
Instructions.
2. Release the throttle trigger and let the engine idle. If
the engine stops, insert a small phillips or flat blade
screwdriver into the hole in the air filter/muffler cover
(Fig. 30). Turn the idle speed screw in, clockwise,
1/8 of a turn at a time (as needed) until the engine
idles smoothly.
CARBURETOR ADJUSTMENT
The idle speed of the engine is adjustable through the air
filter/muffler cover (Fig. 30).
NOTE: Careless adjustments can seriously damage your
unit. An authorized service dealer should make
carburetor adjustments.
NOTE: The cutting attachment should not rotate when
the engine idles.
3. If the cutting attachment rotates when the engine idles,
turn the idle speed screw counterclockwise 1/8 of a
turn at a time (as needed), to reduce idle speed.
Checking the fuel mixture, cleaning the air filter, and
adjusting the idle speed should solve most engine
problems. If not and all of the following are true:
the engine will not idle
the engine hesitates or stalls on acceleration
there is a loss of engine power
Have the carburetor adjusted by an authorized service dealer.
REPLACING THE SPARK PLUG
Use a Champion RDJ7Y spark plug, or equivalent. The
correct air gap is 0.020 inch (0.5 mm). Remove the plug
after every 25 hours of operation and check its condition.
1. Stop the engine and allow it to cool. Grasp the plug
wire firmly and pull it from the spark plug.
2. Clean around the spark plug. Remove the spark plug
from the cylinder head by turning a 5/8-inch socket
counterclockwise.
3. Replace a cracked, fouled or dirty spark plug. Set
the air gap at 0.020 in. (0.5 mm) using a feeler gauge
(Fig. 31).
4. Install a correctly-gapped spark plug in the cylinder
head. Tighten by turning the 5/8-inch socket
clockwise until snug.
If using a torque wrench torque to:
110-120 in.•lb. (12.3-13.5 N•m)
Do not over tighten.
0.020 in.
(0.5 mm)
Fig. 31
CAUTION: Do not sand blast, scrape or
clean electrodes. Grit in the engine could
damage the cylinder.
WARNING: The cutting attachment may spin
during idle speed adjustments. Wear
protective clothing and observe all safety
instructions to prevent serious personal injury.
WARNING: To prevent serious personal
injury, make sure the cutting attachment
has stopped rotating before you turn it off
and set it down.
MAINTENANCE AND REPAIR INSTRUCTIONS
Idle Speed Screw
Fig. 30
18
MAINTENANCE AND REPAIR INSTRUCTIONS
CLEANING
Use a small brush to clean off the outside of the unit.
Do not use strong detergents. Household cleaners that
contain aromatic oils such as pine and lemon, and
solvents such as kerosene, can damage plastic housing
or handle. Wipe off any moisture with a soft cloth.
STORAGE
Never store a fueled unit where fumes may reach an
open flame or spark.
Allow the engine to cool before storing.
Store the unit locked up to prevent unauthorized use
or damage.
Store the unit in a dry, well-ventilated area.
Store the unit out of the reach of children.
LONG TERM STORAGE
If you plan on storing the unit for an extended time, use
the following storage procedure:
1. Drain all fuel from the fuel tank into a container with
the same 2-cycle fuel mixture. Do not use fuel that
has been stored for more than 60 days. Dispose of
the old fuel/oil mix in accordance to Federal, State
and Local regulations.
2. Start the engine and allow it to run until it stalls. This
ensures that all fuel has been drained from the
carburetor.
3. Allow the engine to cool. Remove the spark plug and
put 1 oz. (30 ml) of any high quality motor oil or
2-cycle oil into the cylinder. Pull the starter rope
slowly to distribute the oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil
from the cylinder before attempting to start the
trimmer after storage.
4. Thoroughly clean the unit and inspect it for any loose
or damaged parts. Repair or replace damaged parts
and tighten loose screws, nuts or bolts. The unit is
ready for storage.
TRANSPORTING
Allow the engine to cool before transporting.
Drain fuel from unit.
Tighten fuel cap before transporting.
Secure the unit while transporting.
WARNING: To avoid serious personal injury,
always turn your trimmer off and allow it to
cool before you clean or service it.
ACCESSORIES/REPLACEMENT PARTS
2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147543
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610311
Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . .182747
Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472
Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460
Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465
Outer Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181457
Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464
Bump Knob™ . . . . . . . . . . . . . . . . . . . . . . . . . . . 181468
Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000
Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . 682075
For specific replacement parts, refer to the parts list
located on the inside back cover of this manual.
19
If further assistance is required, contact your authorized service dealer.
CAUSE ACTION
Cutting attachment bound with grass Stop the engine and clean cutting attachment
Cutting attachment out of line Refill with new line
Inner reel bound up Replace the inner reel
Cutting head dirty Clean inner reel and outer spool
Line welded Disassemble, remove the welded section and rewind
Line twisted when refilled Disassemble and rewind the line
Not enough line is exposed Push the bump knob and pull out line until 4 inches
(102 mm) of line is outside of the cutting attachment
CAUSE ACTION
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Improper carburetor adjustment Take to an authorized service dealer for an adjustment
Fouled spark plug Replace or clean the spark plug
Plugged spark arrestor Clean or replace spark arrestor
CAUSE ACTION
Empty fuel tank Fill fuel tank with properly mixed fuel
Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times
Engine is flooded Squeeze the trigger and pull the starter rope
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Fouled spark plug Replace or clean the spark plug
Plugged spark arrestor Clean or replace spark arrestor
ENGINE WILL NOT START
ENGINE WILL NOT IDLE
ENGINE WILL NOT ACCELERATE
ENGINE LACKS POWER OR STALLS WHEN CUTTING
CAUSE ACTION
Air filter is plugged Replace or clean the air filter
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Improper carburetor adjustment Adjust according to the Carburetor Adjustments section
CAUSE ACTION
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Improper carburetor adjustment Take to an authorized service dealer for an adjustment
Cutting attachment bound with grass Stop the engine and clean the cutting attachment
Dirty air filter Clean or replace the air filter
Plugged spark arrestor Clean or replace spark arrestor
CUTTING ATTACHMENT WILL NOT ADVANCE LINE
CAUSE ACTION
Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head
CUTTING LINE ADVANCES UNCONTROLLABLY
TROUBLESHOOTING
20
SPECIFICATIONS
ENGINE*
DRIVE SHAFT and CUTTING ATTACHMENT*
*All specifications are based on the latest product information available at the time of printing. We reserve the right to
make changes at any time without notice.
Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle
Stroke................................................................................................................................................... 1.25 in. (31.75 mm.)
Clutch Type ......................................................................................................................................................... Centrifugal
Displacement............................................................................................................................................ 1.9 cu in. (31 cc.)
Operating RPM.................................................................................................................................................. 6,600
+ rpm
Idle Speed RPM ...................................................................................................................................... 3,200 - 4,400 rpm
Ignition Type.......................................................................................................................................................... Electronic
Ignition Switch................................................................................................................................................... Slide Switch
Spark Plug Gap...................................................................................................................................... 0.020 in. (0.5 mm.)
Lubrication................................................................................................................................................... Fuel/Oil Mixture
Fuel/Oil Ratio................................................................................................................................................................. 40:1
Carburetor....................................................................................................................................... Diaphragm, All-Position
Starter............................................................................................................................................................... Auto Rewind
Muffler..................................................................................................................................................... Baffled with Guard
Throttle............................................................................................................................................... Manual Spring Return
Fuel Tank Capacity................................................................................................................................... 12 fl.oz. (355 ml.)
Drive Shaft Housing ............................................................................................................................................ Steel Tube
Throttle Control ........................................................................................................................................ Finger-Tip Trigger
Approximate Unit Weight (No fuel, with cutting attachment, shield and D-handle).................................... 12 lbs. (5.5 kg.)
Cutting Mechanism................................................................................................ SpeedSpool
®
Dual String Cutting Head
Shoulder Strap ........................................................................................................................................................ Optional
Line Spool Diameter.................................................................................................................................... 3 in. (76.2 mm.)
Trimming Line Diameter....................................................................................................................... 0.080 in. (2.03 mm.)
Cutting Path Diameter................................................................................................................................ 15 in. (38.1 cm.)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

MTD 705r Le manuel du propriétaire

Catégorie
Coupe-herbe
Taper
Le manuel du propriétaire

dans d''autres langues