MTD 705r Le manuel du propriétaire

Marque: MTD

Modèle: 705r

Catégorie: Coupe-herbe

Taper: Le manuel du propriétaire

2-Cycle Gas Trimmer

OPERATOR’S MANUAL

FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or

1-800-668-1238 in CANADA

www.RyobiOutdoor.com

IMPORTANT MANUAL DO NOT THROW AWAY

705r

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS

AND SPECIFICATIONS

All information, illustrations and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

2003 MTD SOUTHWEST INC

SpeedSpool is a registered trademark of MTD

SOUTHWEST INC.

SERVICE INFORMATION

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

• Call 1-800-345-8746 in the United States, or

1-800-668-1238 in Canada, to obtain a list of

authorized service dealers near you

• Go to www.RyobiOutdoor.com on the World Wide

Web for a list of authorized service dealers

DO NOT RETURN THE UNIT TO THE RETAILER.

NOTE: PROOF OF PURCHASE WILL BE REQUIRED

FOR WARRANTY SERVICE.

Make sure you carefully read and understand this

manual before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE

US PATENTS, OTHER PATENTS PENDING.

INTRODUCTION TABLE OF CONTENTS

I. California Proposition 65 Warning . . . . . . . . . . . . . . . . 3

II. Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . 3-7

A. Important Safety Information . . . . . . . . . . . . . . . . . 4

B. Safety and International Symbols . . . . . . . . . . . . . . 6

C. Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

III. Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 8

A. Installing and Adjusting the D-Handle . . . . . . . . . . 8

B. Installing the Cutting Attachment Shield . . . . . . . . 8

IV. Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . 9

V. Starting/Stopping Instructions . . . . . . . . . . . . . . . . . 10

VI. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . 11

A. Holding the Trimmer . . . . . . . . . . . . . . . . . . . . . . . 11

B. Adjusting Trimming Line Length . . . . . . . . . . . . . . 11

C. Tips for Best Trimming Results . . . . . . . . . . . . . . 11

D. Decorative Trimming . . . . . . . . . . . . . . . . . . . . . . . 11

VII. Maintenance and Repair Instructions . . . . . . . . . 12-18

A. Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . 12

B. Line Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

C. Installing a Pre-wound Wheel . . . . . . . . . . . . . . . .13

D. Cleaning the SpeedSpool . . . . . . . . . . . . . . . . . . . 14

E. Air Filter Maintenance . . . . . . . . . . . . . . . . . . . . . . 15

F. Spark Arrestor Maintenance . . . . . . . . . . . . . . . . . 16

G. Carburetor Adjustment . . . . . . . . . . . . . . . . . . . . . 17

H. Replacing the Spark Plug . . . . . . . . . . . . . . . . . . . 17

I. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

J. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

K. Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 18

L. Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

M.Accessories/Replacement Parts . . . . . . . . . . . . . . 18

VIII.Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . 19

IX. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

X. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

XI. Parts List . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover

CONTENTS OF CARTON

•Model 705r Trimmer with SpeedSpool

Bump Head

Cutting Attachment

∆ D-Handle and Hardware

∆ Cutting Attachment Shield with Hardware

•Operator's Manual

• Product Registration Card

• Bottle of 2-Cycle Oil

∆ This item will either be installed on the unit or in the

hardware pack

NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S.

Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by

law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a

spark arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the

prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If

it requires replacement, ask your LOCAL SERVICE DEALER to install the Accessory Part #182747 Spark Arrestor Kit.

Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so

can result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-668-1238 in CANADA

SPARK ARRESTOR

WARNING!

RULES FOR SAFE OPERATION

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

DANGER: Failure to obey a safety warning

will result in serious injury to yourself or to

others. Always follow the safety

precautions to reduce the risk of fire,

electric shock and personal injury.

WARNING: Failure to obey a safety

warning can result in injury to yourself and

others. Always follow the safety

precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION: Failure to obey a safety warning

may result in property damage or personal

injury to yourself or to others. Always follow

the safety precautions to reduce the risk of

fire, electric shock and personal injury.

SAFETY ALERT SYMBOL: Indicates

danger, warning or caution. Attention is

required in order to avoid serious personal

injury. May be used in conjunction with

other symbols or pictographs.

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital

to the operation or maintenance of the

equipment.

SYMBOL MEANING

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

• Children under the age of 15 must not use the unit;

teens may operate the unit with adult guidance.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace cutting attachment parts

that are cracked, chipped or damaged in any way.

Make sure the cutting attachment is properly installed

and securely fastened. Be sure that the cutting

attachment shield is properly attached, and positioned

as recommended. Failure to do so can result in

personal injury to the operator and bystanders, as well

as damage to the unit.

• Use only 0.080 inch (2.03 mm) diameter Genuine

Factory Parts™ replacement line. Never use metal-

reinforced line, wire, chain or rope. These can break

off and become dangerous projectiles.

• Be aware of risk of injury to the head, hands and feet.

• Clear the area to be cut before each use. Remove

rocks, broken glass, nails, wire, string and other

objects which may be thrown or become entangled in

the cutting attachment. Clear the area of children,

bystanders and pets; keep them outside a 50-foot

(15 m.) radius, at a minimum. Even then, they are still

at risk from thrown objects. Encourage bystanders to

wear eye protection. If you are approached, stop the

unit immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments

or repairs before using the unit.

• This unit was not designed to be used as a brushcutter.

Do not attach or operate this unit with any type of

brushcutting blade or brushcutting attachment.

• IMPORTANT SAFETY INFORMATION •

SAFETY WARNINGS FOR GAS TRIMMERS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Always stop the engine and allow it to cool before

filling the fuel tank. Never remove the fuel tank cap or

add fuel when the engine is hot. Never operate the unit

without the fuel cap securely in place. Loosen the fuel

tank cap slowly to relieve any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where

there are no sparks or flames. Remove the fuel cap

slowly, and only after the engine stops. Do not smoke

while fueling or mixing fuel. Wipe up any spilled fuel

from the unit immediately.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke. Keep sparks and open flames away from the

area while adding fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can be fatal.

Operate this unit only in a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face or

dust mask if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long

sleeve shirt. Do not wear loose clothing, jewelry, short

pants, sandals or go barefoot. Secure hair above

shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without

both trimming lines extended, and the proper line

installed. Do not extend the trimming line beyond the

length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have

the unit adjusted by an authorized service technician.

• Adjust the D-handle to your size in order to provide the

best grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

WARNING

When using the unit, you must

follow the safety rules. For your own safety

and that of bystanders, please read these

instructions before operating the unit.

Please keep the instructions for later use.

WARNING

Gasoline is highly flammable,

and its vapors can explode if ignited. Take

the following precautions:

RULES FOR SAFE OPERATION

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. Refer

to Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended

purpose.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it rotates.

• Do not touch the engine, gear housing or muffler.

These parts get extremely hot from operation, even

after the unit is turned off.

• Do not operate the engine faster than the speed

needed to cut, trim or edge. Do not run the engine at

high speed when not cutting.

• Always stop the engine when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop the unit, switch the engine to off, and disconnect

the spark plug for maintenance or repair.

• Use only Genuine Factory Parts™ replacement parts

and accessories for this unit. These are available from

your authorized service dealer. Use of any

unauthorized parts or accessories could lead to

serious injury to the user, or damage to the unit, and

void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

• To reduce fire hazard, replace a faulty muffler and

spark arrestor. Keep the engine and muffler free from

grass, leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

• Never store a fueled unit inside a building where fumes

may reach an open flame or spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to

prevent unauthorized use or damage, out of the reach

of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use, see Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ OPERATOR'S

MANUAL

Read the Operator’s Manual(s) and

follow all warnings and safety

instructions. Failure to do so can

result in serious injury to the

operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING: Thrown objects and

loud noise can cause severe eye

injury and hearing loss. Wear eye

protection meeting ANSI Z87.1-1989

standards and ear protection when

operating this unit.

Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders,

especially children and pets, at least

50 feet (15 m.) from the operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the

proper type of oil.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

• THROWN OBJECTS AND

ROTATING CUTTER CAN CAUSE

SEVERE INJURY

WARNING

Do not operate without

the cutting attachment shield in

place. Keep away from the rotating

cutting attachment.

•ON/OFF STOP CONTROL

ON / START / RUN

•ON/OFF STOP CONTROL

OFF or STOP

• HOT SURFACE WARNING

Do not touch a hot muffler or

cylinder. You may get burned. These

parts get extremely hot from

operation. When turned off they

remain hot for a short time.

• SHARP BLADE

WARNING: Sharp blade on cutting

attachment shield. To prevent

serious injury, do not

touch line cutting blade.

• CHOKE CONTROL

A • FULL choke position

B •

PARTIAL choke position

C •

RUN position

RULES FOR SAFE OPERATION

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

KNOW YOUR UNIT

Cutting Attachment

Shield

Fuel Cap

Throttle

Control

Cutting Attachment

Shaft Grip

Primer Bulb

Choke Lever

Air Filter/Muffler

Cover

Spark Plug

On/Off Stop Control

Shaft

Housing

Starter Rope Grip

Line Cutting Blade

Muffler

D-handle

ASSEMBLY INSTRUCTIONS

Fig. 2

INSTALL AND ADJUST THE D-HANDLE

1. Push the D-handle down onto the shaft housing so

that the handle slants towards the shaft grip (Fig. 1).

The squared bolt hole in the handle is to the right.

2. Insert the shoulder bolt into the squared hole in the

handle and push through. On the left side of the

handle, place the washer on the bolt, then screw the

wing nut onto the bolt. Do not tighten until you make

the handle adjustment.

3. Rotate the D-handle to place the grip above the top

of the shaft housing. Place it a minimum of 6 inches

(15.24 cm) from the end of the shaft grip.

4. While holding the unit in the operating position

(Fig. 2), position the D-handle to the location that

provides you the best grip.

5. Tighten the wing nut until the D-handle is secure.

Fig. 1

Bolt

Washer

Wing Nut

Tighten

Shaft Grip

D-Handle

Minimum 6 inches

(15.24 cm)

Shaft Housing

INSTALL THE CUTTING ATTACHMENT SHIELD

Use the following instructions if the cutting attachment

shield on your unit is not installed.

1. Place the cutting attachment shield onto the shaft

housing above the clamp assembly (Fig. 3).

2. Push the cutting attachment shield down to the top of

the cutting attachment assembly and then rotate the

cutting attachment shield until the screw holes align

and the guard fits into the recessed pocket (Fig. 4).

3. Install the screws with a Phillips screwdriver (Fig. 5).

WARNING: To prevent serious personal

injury, never operate the trimmer without

the cutting attachment shield in place.

Fig. 3

Fig. 4

Shaft Housing

(4) Screws

Clamp

Assembly

Cutting

Attachment

Assembly

Cutting Attachment

Shield

Recessed

Pocket

Fig. 5

OIL AND FUEL INFORMATION

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State and Local regulations.

CAUTION: For proper engine operation and

maximum reliability, pay strict attention to

the oil and fuel mixing instructions on the

2-cycle oil container. Using improperly

mixed fuel can severely damage the engine.

WARNING: Gasoline is extremely

flammable. Ignited Vapors may explode.

Always stop the engine and allow it to cool

before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING: Remove fuel cap slowly to avoid

injury from fuel spray. Never operate the unit

without the fuel cap securely in place

WARNING: Add fuel in a clean, well

ventilated area outdoors. Wipe up any

spilled fuel immediately. Avoid creating a

source of ignition for spilt fuel. Do not start

the engine until fuel vapors dissipate.

OIL AND FUEL MIXING INSTRUCTIONS

Old and/or improperly mixed fuel are the main reasons

for the unit not running properly. Be sure to use fresh,

clean unleaded fuel. Follow the instructions carefully for

the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol, or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate. It forms

acids when stored. When using alcohol-blended fuel,

use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions:

• Always use the fresh fuel mix explained in your

operator's manual

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing

the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit

contains a fuel additive which will help inhibit corrosion

and minimize the formation of gum deposits. It is

recommended that you use our 2-cycle oil with this unit.

If unavailable, use a good 2-cycle oil designed for

air-cooled engines along with a fuel additive, such as

STA-BIL

Gas Stabilizer or an equivalent. Add 0.8 oz.

(23 ml.) of fuel additive per gallon of fuel according to the

instructions on the container. NEVER add fuel additives

directly to the unit's fuel tank.

Thoroughly mix the proper ratio of 2-cycle engine oil

with unleaded gasoline in a separate fuel can. Use a 40:1

fuel/oil ratio. Do not mix them directly in the engine fuel

tank. See the table below for specific gas and oil mixing

ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed

with one 3.2 oz. (95 ml.) bottle of

2-cycle oil makes a 40:1 fuel/oil ratio.

UNLEADED GAS 2 CYCLE OIL

1 US. GALLON + 3.2 FL. OZ.

(3.8 LITERS) (95 ml)

1 LITER + 25 ml

MIXING RATIO - 40:1

STARTING INSTRUCTIONS

1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.

Refer to Oil and Fuel Mixing Instructions.

2. Put the On/Off Stop Control in the ON (I) position

(Fig. 6).

3. Fully press and release the primer bulb 10 times,

slowly, until FUEL IS VISIBLE IN THE PRIMER

BULB (Fig. 7). If you can’t see fuel in the bulb, press

and release the bulb as many times as it takes before

you can see fuel in it.

4. Place the choke lever in the FULL choke (A )

position (Fig. 7).

5. With the unit in the starting position (Fig. 8), squeeze

the throttle control to the wide open (full throttle)

position. Pull the starter rope briskly 5 times while still

in the FULL choke (A ) position. If the engine

attempts to run before the fifth pull, proceed to step 6.

NOTE: The engine will not run in the FULL choke (A )

position.

6. Place the choke lever in the PARTIAL choke (B )

position (Fig. 7).

7. Pull starter rope briskly 1 to 3 times to start the

engine (Fig. 8).

NOTE: Squeeze the throttle control until the engine has

started and warmed up.

8. If the engine does not start, repeat steps 3 through 7.

NOTE: If the engine floods while trying to start, place the

choke lever in the RUN (C ) position (Fig. 7).

Squeeze the throttle control. Pull the starter rope

briskly. The engine should start within three (3) to

eight (8) pulls.

9. Squeeze the throttle control to warm up the engine

for 5 to 10 seconds. Place the choke lever in the

RUN (C ) position (Fig. 7).

NOTE: Choking is unnecessary when starting a warm

engine. Put the On/Off Stop Control in the ON

position (Fig. 6), and start in PARTIAL choke

(B ) position (Fig. 7). After starting, place the

choke lever in the RUN (C ) position.

WARNING:

Operate this unit only in a well-

ventilated outdoor area. Carbon monoxide

exhaust fumes can be lethal in a confined area.

WARNING: Avoid accidental starting. Make

sure you are in the starting position when

pulling the starter rope (Fig. 8).

To avoid

serious injury, the operator and unit must be

in a stable position while starting.

STARTING/STOPPING INSTRUCTIONS

Fig. 8

Starter Rope

Throttle Control

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control (Fig. 8).

Allow the engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position

(Fig. 6).

Fig. 6

On/Off Stop Control

Start/On (I)

Stop/Off (O)

Choke Lever

Full Choke

Position (A)

Run

Position (C)

Partial Choke

Position (B)

Primer Bulb

Fig. 7

OPERATING INSTRUCTIONS

NOTE: Do not rest the Bump Head™ on the ground

while the unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence posts

TIPS FOR BEST TRIMMING RESULTS

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of the

line to do the cutting, especially along walls. Cutting with

more than the tip will reduce cutting efficiency and may

overload the engine.

• Cut grass over 8 inches (200 mm) by working from top

to bottom in small increments to avoid premature line

wear or engine drag.

• Cut from right to left whenever possible. Cutting to the left

improves the unit's cutting efficiency. Clippings are

thrown away from the operator.

• Slowly move the trimmer into and out of the cutting

area at the desired height. Move either in a forward-

backward or side-to-side motion. Cutting shorter

lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon;

• Adherence of the listed trimming techniques

• What vegetation is cut

• Where vegetation is cut

For example, the line will wear faster when trimming against

a foundation wall as opposed to trimming around a tree.

HOLDING THE TRIMMER

Before operating the unit, stand in the operating position

(Fig. 9). Check for the following:

• The operator is wearing eye protection and proper

clothing

• With a slightly-bent right arm, the operator’s right hand

is holding the shaft grip

• The operator’s left arm is straight, the left hand holding

the D-handle

• The unit is at waist level

•

The cutting attachment is parallel to the ground and

easily contacts the grass without the need to bend ove

Fig. 9

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to

release trimming line without stopping the engine. To

release more line, lightly tap the cutting attachment on the

ground (Fig. 10) while operating the trimmer at high speed.

NOTE: Always keep the trimming line fully extended.

Line release becomes more difficult as cutting

line becomes shorter

Fig. 10

CAUTION:

Do not remove or alter the line

cutting blade assembly. Excessive line length

will make the clutch overheat. This may lead to

serious personal injury or damage to the unit.

WARNING: Always wear eye, hearing, foot

and body protection to reduce the risk of

injury when operating this unit.

Each time the head is bumped, about 1 inch (25.4 mm)

of trimming line releases. A blade in the cutting

attachment shield will cut the line to the proper length if

any excess line is released.

For best results, tap the bump knob on bare ground or

hard soil. If you attempt a line release in tall grass, the

engine may stall. Always keep the trimming line fully

extended. Line release becomes more difficult when the

cutting line gets shorter.

DECORATIVE TRIMMING

Decorative trimming is accomplished by removing all

vegetation around trees, posts, fences, etc.

Rotate the whole unit so that the cutting attachment is at

a 30° angle to the ground (Fig. 11).

Fig. 11

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures take your unit to any non-road

engine repair establishment, individual or

authorized service dealer.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by any non-road engine repair

establishment, individual or authorized service

dealer.

In order to assure peak performance of your engine,

inspection of the engine exhaust port may be necessary

after 50 hours of operation. If you notice lost RPM, poor

performance or general lack of acceleration, this service

may be required. If you feel your engine is in need of this

inspection, refer service to any non-road engine repair

establishment, individual or authorized service dealer for

repair. DO NOT attempt to perform this process yourself

as engine damage may result from contaminants

involved in the cleaning process for the port.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine Fill fuel tank with fresh fuel Page 9

Every 10 hours Clean and re-oil air filter Page 15

Every 25 hours

Check and clean spark arrestor

Check spark plug condition and gap

Page 16

Page 17

Every 50 hours

Inspect exhaust port and spark arrestor screen for clogging or

obstruction to assure maximum performance levels

Page 16

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: To prevent serious injury, never

perform maintenance or repairs with unit

running. Always service and repair a cool unit.

Disconnect the spark plug wire to ensure that

the unit cannot start.

LINE INSTALLATION FOR THE SPEEDSPOOL

Always use Genuine Factory Parts™ 0.080 inch (2.03

mm) replacement line. Lines other than those specified

may make the engine overheat or fail.

There are two methods to replace the SpeedSpool

trimming line:

• Wind the inner reel with new line

• Install a pre-wound inner reel

Winding the Inner Reel With New Line

NOTE: It Is unnecessary to remove the bump knob to

install a new trimming line.

1. Cut two pieces of 0.080 inch (2.03 mm) trimming

line, 10 feet (3 m) long.

2. Hold the outer spool and turn the inner reel

counterclockwise to line up the arrows on the outer

spool and inner reel (Fig. 12).

Top View Of The SpeedSpool

Outer Spool

Inner Reel

Fig. 12

Bump Knob

Arrows

WARNING: Always use the correct line

length when installing trimming line on the

unit. The line may not release properly if the

line is too long.

WARNING: Never use metal-reinforced

line, wire, chain or rope. These can break

off and become dangerous projectiles.

MAINTENANCE AND REPAIR INSTRUCTIONS

Line Locking Hole

Trimming Line

Line Loading Hole

Eyelet

5. Insert the line into the locking hole (Fig. 14). Do not

push the line more than a 1/2 inch (12.7 mm) into the

line locking hole. The line will form a small loop

(Fig. 14) when it is inserted correctly.

3. Pull old line out of the line loading and line locking

holes (Fig. 13 and 14).

4. Insert a piece of trimming line straight into one of the

two eyelets in the outer spool. Push it up through the

line loading hole in the inner reel (Fig. 13). Do not

bend the line when inserting it into the eyelet.

Fig. 13

Fig. 14

6. Pull the line from the outer spool until the line is tight

against the inner reel (Fig. 15).

Fig. 15

INSTALLING A PRE-WOUND REEL

1. Turn the bump knob counterclockwise and remove

the bump knob, spring and foam seal (Fig. 18).

9. If winding the line becomes difficult or if the line

jams, pull the ends of the line from the spool

(Fig. 17). Continue winding the inner reel

counterclockwise.

Fig. 16

Fig. 17

7. Repeat procedures 4-6 with the second piece of line.

8. Hold the outer spool. Wind the inner reel

counterclockwise until approximately four (4) inches

(102 mm) of line remain (Fig. 16).

NOTE: Do not wind the inner reel before installing the

second piece of line.

Bump Knob

Foam Seal

Spring

Inner Reel

Fig. 18

MAINTENANCE AND REPAIR INSTRUCTIONS

SPEEDSPOOL

REPLACEMENT PARTS

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472

Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465

Foam Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181467

Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464

Bump Knob Assembly . . . . . . . . . . . . . . . . . . . . 181468

These SpeedSpool

replacement parts can be

purchased from your local authorized dealer.

4. Hold the inner reel in place and install the bump

knob, spring and foam seal. Press down and turn the

bump knob clockwise. Grasp the ends and pull

firmly to release the line from the holding slots in the

inner reel (Fig. 18).

Releasing the Inner Reel

If the SpeedSpool

does not release line correctly, pull

the ends of the line firmly from the spool (Fig. 17). If this

does not the release line, follow the Cleaning the

SpeedSpool

instructions.

2. Pull the old inner reel with existing line from the outer

spool.

3. Insert the ends of the prewound inner reel line into

the outer spool eyelets (Fig. 19). Push the new inner

reel, arrow side up, into the outer spool.

Fig. 19

4. Remove any existing line from the inner reel before

cleaning. Remove any debris or grass from the knob,

spring, inner reel and foam seal. Wash the inner reel

with warm soapy water (Fig. 21).

Fig. 20

CLEANING THE SPEEDSPOOL

Cleaning the SpeedSpool

may be necessary if:

•A jammed or excessive line must be removed

• The SpeedSpool

becomes difficult to wind or does

not operate correctly when bumping the head on the

ground

1. Hold the outer spool, and unscrew the bump knob

counterclockwise (Fig. 20).

2. Pull out the bump knob, spring and foam seal (Fig. 18).

Shaft

Plunger

NOTE: The inner reel must be totally dry before

reinstalling it into the outer spool. Do not lubricate

the inner reel or outer spool assembly.

6. Place the inner reel into the outer spool.

7. Place the bump knob, spring and foam seal into the

inner reel (Fig. 18).

8. Press the bump knob down and tighten clockwise.

9. Install new line as described in Line Installation for

the SpeedSpool

5. Clean the shaft and the inner surface of the outer

spool. To clean the shaft underneath the plunger,

press down on the plunger (Fig. 22). Remove any dirt

or debris from the shaft.

Fig. 22

Inner Reel

Fig. 21

3. Pull the inner reel with existing line from the outer

spool (Fig. 19).

MAINTENANCE AND REPAIR INSTRUCTIONS

AIR FILTER MAINTENANCE

Removing the Air Filter/Muffler Cover

Place the choke lever in the PARTIAL choke position (B).

NOTE: The choke lever must be in the PARTIAL choke

position (B) to remove the air filter/ muffler cover.

2. Remove the four (4) screws securing the air

filter/muffler cover (Fig. 23). Use a flat blade or

T-20 Torx bit screwdriver.

3. Pull the cover from the engine. Do not force.

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean or service it.

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain the

air filter will VOID the warranty.

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Turn cover over and look inside to locate the air filter.

Remove the air filter from inside the air filter/muffler

cover (Fig. 24).

3. Wash the filter in detergent and water (Fig. 25). Rinse

the filter thoroughly. Squeeze out excess water. Allow

it to dry completely.

4. Apply enough clean SAE 30 oil to lightly coat the filter

(Fig. 26).

5. Squeeze the filter to spread and remove excess oil

(Fig. 27).

Fig. 24

Fig. 25

Fig. 26

Fig. 27

6. Replace the air filter inside the air filter/muffler cover

(Fig. 24).

NOTE: Operating the unit without the air filter and air

filter/muffler cover assembly will VOID the

warranty.

Reinstalling the Air Filter/Muffler Cover

1. Place the air filter/muffler cover over the back of the

carburetor and muffler. Align the screw holes.

2. Insert the four (4) screws into the holes in the air

filter/muffler cover (Fig. 23) and tighten.

Do not over tighten.

Air Filter

Inside Muffler

Cover

Choke Lever

Screws

Partial Choke

Position (B)

Fig. 23

SPARK ARRESTOR MAINTENANCE

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Locate muffler front and the two (2) bolts securing it

to the engine (Fig. 28). Remove the two (2) bolts

using a flatblade screwdriver or 5/16-inch socket or

nut driver. Pull muffler off of the engine.

3. Turn muffler over to the back side and locate the

exhaust gasket. Remove the muffler gasket from the

muffler (Fig. 28).

NOTE: If the exhaust gasket is torn or damaged, replace

it with a new gasket before reassembling muffler.

4. Using a small flatblade screwdriver, carefully pry up

the spark arrestor from the recessed hole (Fig. 29).

Remove the spark arrestor from the muffler.

5. Clean the spark arrestor with a wire brush. Replace it

if it is damaged or if it is impossible to clean

thoroughly (Fig. 29).

6. Reinstall the spark arrestor by pressing it into the

recessed hole on the muffler's back side. Make sure

it fits tightly against the muffler and is not raised up.

7. Place the exhaust gasket against muffler's back side.

Align the gasket bolt holes with the bolt holes in the

muffler. While holding exhaust gasket in place, insert

the bolts into the muffler's front side (Fig. 28).

8. Place the muffler (with the exhaust gasket in place

and bolts inserted), against the engine, aligning the

bolt holes. Tighten the bolts to secure the muffler to

the engine.

If using a torque wrench, torque to:

80-90 in.•lb. (9-10.2 N•m)

9. Reinstall the air filter/muffler cover.

Fig. 29

Fig. 28

Muffler - Front Side

Muffler - Back Side

Bolts

Exhaust

Gasket

Spark

Arrestor

Muffler - Back Side

Spark

Arrestor

Flatblade

Screwdriver

Spark Arrestor

WARNING:

If the muffler is not tightened

securely, it could fall off causing damage to

the unit and possible serious personal injury

MAINTENANCE AND REPAIR INSTRUCTIONS

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason

for improper unit performance. Drain and refill the tank

with fresh, properly-mixed fuel prior to making any

adjustments. Refer to Oil and Fuel Information.

Clean Air Filter

The condition of the air filter is important to the operation

of the unit. A dirty air filter will restrict air flow and

change the air/fuel mixture. This is often mistaken for an

out of adjustment carburetor. Check the condition of the

air filter before adjusting the idle speed screw. Refer to

Air Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel mixture and cleaning the air

filter, the engine still will not idle, adjust the idle speed

screw as follows:

1. Start the engine and let it run at a high idle for a

minute to warm up. Refer to Starting/Stopping

Instructions.

2. Release the throttle trigger and let the engine idle. If

the engine stops, insert a small phillips or flat blade

screwdriver into the hole in the air filter/muffler cover

(Fig. 30). Turn the idle speed screw in, clockwise,

1/8 of a turn at a time (as needed) until the engine

idles smoothly.

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable through the air

filter/muffler cover (Fig. 30).

NOTE: Careless adjustments can seriously damage your

unit. An authorized service dealer should make

carburetor adjustments.

NOTE: The cutting attachment should not rotate when

the engine idles.

3. If the cutting attachment rotates when the engine idles,

turn the idle speed screw counterclockwise 1/8 of a

turn at a time (as needed), to reduce idle speed.

Checking the fuel mixture, cleaning the air filter, and

adjusting the idle speed should solve most engine

problems. If not and all of the following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

REPLACING THE SPARK PLUG

Use a Champion RDJ7Y spark plug, or equivalent. The

correct air gap is 0.020 inch (0.5 mm). Remove the plug

after every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug

from the cylinder head by turning a 5/8-inch socket

counterclockwise.

3. Replace a cracked, fouled or dirty spark plug. Set

the air gap at 0.020 in. (0.5 mm) using a feeler gauge

(Fig. 31).

4. Install a correctly-gapped spark plug in the cylinder

head. Tighten by turning the 5/8-inch socket

clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

0.020 in.

(0.5 mm)

Fig. 31

CAUTION: Do not sand blast, scrape or

clean electrodes. Grit in the engine could

damage the cylinder.

WARNING: The cutting attachment may spin

during idle speed adjustments. Wear

protective clothing and observe all safety

instructions to prevent serious personal injury.

WARNING: To prevent serious personal

injury, make sure the cutting attachment

has stopped rotating before you turn it off

and set it down.

MAINTENANCE AND REPAIR INSTRUCTIONS

Idle Speed Screw

Fig. 30

MAINTENANCE AND REPAIR INSTRUCTIONS

CLEANING

Use a small brush to clean off the outside of the unit.

Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

STORAGE

• Never store a fueled unit where fumes may reach an

open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

If you plan on storing the unit for an extended time, use

the following storage procedure:

1. Drain all fuel from the fuel tank into a container with

the same 2-cycle fuel mixture. Do not use fuel that

has been stored for more than 60 days. Dispose of

the old fuel/oil mix in accordance to Federal, State

and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all fuel has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and

put 1 oz. (30 ml) of any high quality motor oil or

2-cycle oil into the cylinder. Pull the starter rope

slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil

from the cylinder before attempting to start the

trimmer after storage.

4. Thoroughly clean the unit and inspect it for any loose

or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts. The unit is

ready for storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Drain fuel from unit.

• Tighten fuel cap before transporting.

• Secure the unit while transporting.

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean or service it.

ACCESSORIES/REPLACEMENT PARTS

2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147543

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610311

Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . .182747

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472

Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 181465

Outer Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181457

Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464

Bump Knob™ . . . . . . . . . . . . . . . . . . . . . . . . . . . 181468

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000

Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . 682075

For specific replacement parts, refer to the parts list

located on the inside back cover of this manual.

If further assistance is required, contact your authorized service dealer.

CAUSE ACTION

Cutting attachment bound with grass Stop the engine and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section and rewind

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the bump knob and pull out line until 4 inches

(102 mm) of line is outside of the cutting attachment

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Take to an authorized service dealer for an adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

Empty fuel tank Fill fuel tank with properly mixed fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Engine is flooded Squeeze the trigger and pull the starter rope

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN CUTTING

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Adjust according to the Carburetor Adjustments section

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Take to an authorized service dealer for an adjustment

Cutting attachment bound with grass Stop the engine and clean the cutting attachment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

CAUSE ACTION

Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head

CUTTING LINE ADVANCES UNCONTROLLABLY

TROUBLESHOOTING

SPECIFICATIONS

ENGINE*

DRIVE SHAFT and CUTTING ATTACHMENT*

*All specifications are based on the latest product information available at the time of printing. We reserve the right to

make changes at any time without notice.

Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle

Stroke................................................................................................................................................... 1.25 in. (31.75 mm.)

Clutch Type ......................................................................................................................................................... Centrifugal

Displacement............................................................................................................................................ 1.9 cu in. (31 cc.)

Operating RPM.................................................................................................................................................. 6,600

+ rpm

Idle Speed RPM ...................................................................................................................................... 3,200 - 4,400 rpm

Ignition Type.......................................................................................................................................................... Electronic

Ignition Switch................................................................................................................................................... Slide Switch

Spark Plug Gap...................................................................................................................................... 0.020 in. (0.5 mm.)

Lubrication................................................................................................................................................... Fuel/Oil Mixture

Fuel/Oil Ratio................................................................................................................................................................. 40:1

Carburetor....................................................................................................................................... Diaphragm, All-Position

Starter............................................................................................................................................................... Auto Rewind

Muffler..................................................................................................................................................... Baffled with Guard

Throttle............................................................................................................................................... Manual Spring Return

Fuel Tank Capacity................................................................................................................................... 12 fl.oz. (355 ml.)

Drive Shaft Housing ............................................................................................................................................ Steel Tube

Throttle Control ........................................................................................................................................ Finger-Tip Trigger

Approximate Unit Weight (No fuel, with cutting attachment, shield and D-handle).................................... 12 lbs. (5.5 kg.)

Cutting Mechanism................................................................................................ SpeedSpool

Dual String Cutting Head

Shoulder Strap ........................................................................................................................................................ Optional

Line Spool Diameter.................................................................................................................................... 3 in. (76.2 mm.)

Trimming Line Diameter....................................................................................................................... 0.080 in. (2.03 mm.)

Cutting Path Diameter................................................................................................................................ 15 in. (38.1 cm.)

La page charge ...