JVC KD-LH1101 Le manuel du propriétaire

GET0152-001A

[E/EX]

KD-LH1101

CD RECEIVER

CD-RECEIVER

RECEPTEUR CD

CD-RECEIVER

ENGLISH

DEUTSCH

NEDERLANDS

FRANÇAIS

For installation and connections, refer to the separate manual.

Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.

Pour l’installation et les raccordements, se référer au manuel séparé.

Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende

handleiding.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

• This unit is equipped with the display demonstration. To cancel it, see page 8.

• Dieses Gerät ist mit einer Demonstrationsfunktion für das Display ausgestattet. Auf Seite 8 wird

beschrieben, wie Sie diese Demonstrationsfunktion deaktivieren können.

• Cet appareil est équipé d’une fonction de démonstration des affichages. Pour l’annuler, référez-

vous à la page 8.

• Dit toestel heeft een display-demonstratiefunctie. Zie bladzijde 8 voor het annuleren van deze

functie.

Cover001AKD-LH1101[E_EX]f.p65 2/26/03, 11:42 AM3

2

ENGLISH

How to reset your unit

After detaching the control panel, press the

reset button on the panel holder using a

ball-point pen or a similar tool.

This will reset the built-in microcomputer.

Note:

Your preset adjustments—such as preset channels or

sound adjustments—will also be erased.

Caution:

If the temperature inside the car is below 0°C, the movement of animation and text scroll will be halted on

the display to prevent the display from being blurred. (LOW TEMP.) indicator appears on the display.

When the temperature increases, the operating temperature is resumed, and these functions will start

working again.

CAUTION on Volume Setting:

Discs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for

example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the

volume before playing a disc and adjust it as required during playback.

Position And Reproduction Of Labels

IMPORTANT FOR LASER PRODUCTS

Precautions:

1.CLASS 1 LASER PRODUCT

2.CAUTION: Invisible laser radiation when open and

interlock failed or defeated. Avoid direct exposure to

beam.

3.CAUTION: Do not open the top cover. There are no

user-serviceable parts inside. Leave all servicing to

qualified service personnel.

4.CAUTION: This CD player uses invisible laser radiation

and is equipped with safety switches to prevent

radiation emission when unloading CDs. It is dangerous

to defeat the safety switches.

5.CAUTION: Use of controls, adjustments or performance

of procedures other than those specified herein may

result in hazardous radiation exposure.

CAUTION: Invisible laser

radiation when open and

interlock failed or defeated.

AVOID DIRECT EXPOSURE

TO BEAM. (e)

ADVARSEL: Usynlig laser -

stråling ved åbning, når

sikkerhedsafbrydere er ude

af funktion. Undgåudsæt-

telse for stråling. (d)

VARNING: Osynlig laser-

strålning när denna del är

öppnad och spärren är

urkopplad. Betrakta

ej

strålen. (s)

VARO: Avattaessa ja

suojalukitus ohitettaessa

olet alttiina näkymättö-

mälle lasersäteilylle.

Älä katso säteeseen. (f)

Caution:

This product contains a laser component

of higher laser class than Class 1.

Bottom panel of the main unit

Name/Rating plate

Note:

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on

the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

EN02-04KD-LH1101[E_EX]f.p65 2/26/03, 11:42 AM2

3

ENGLISH

CONTENTS

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

How to reset your unit ............................... 2

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

Illumination Navigation for easy

operations ............................................... 4

Remote controller ...................................... 5

Preparing the remote controller ................ 6

BASIC OPERATIONS ....................... 7

Turning on the power ................................ 7

Canceling the display demonstration ........ 8

Setting the clock ........................................ 9

RADIO OPERATIONS ...................... 10

Listening to the radio ................................. 10

Storing stations in memory ....................... 11

Tuning in to a preset station ...................... 13

Changing the display pattern .................... 14

RDS OPERATIONS ......................... 15

What you can do with RDS ....................... 15

Other convenient RDS functions and

adjustments ............................................ 20

CD OPERATIONS ........................... 22

Playing a CD ............................................. 22

Locating a track or a particular portion

on a CD .................................................. 23

Selecting CD playback modes .................. 24

Prohibiting CD ejection ............................. 25

Changing the display pattern .................... 26

SOUND ADJUSTMENTS ................... 27

Adjusting the sound .................................. 27

Selecting preset sound modes

(iEQ: intelligent equalizer) ...................... 28

Storing your own sound adjustments ........ 29

Activating the level meter .......................... 30

OTHER MAIN FUNCTIONS ................ 31

Changing the general settings (PSM) ....... 31

Selecting the dimmer mode ...................... 35

Changing the display color ........................ 36

Assigning names to the sources ................ 38

Detaching the control panel ...................... 39

CD CHANGER OPERATIONS .............. 40

Playing discs ............................................. 40

Selecting a disc/folder/track using

the name lists ......................................... 43

Selecting the playback modes .................. 44

Changing the display information .............. 46

EXTERNAL COMPONENT OPERATIONS ... 47

Playing an external component ................. 47

DAB TUNER OPERATIONS ................ 48

Tuning in to an ensemble and one of the

services .................................................. 48

Storing DAB services in memory .............. 49

Tuning in to a preset DAB service ............. 50

What you can do more with DAB .............. 51

Changing the display information .............. 52

ADDITIONAL INFORMATION ............. 53

TROUBLESHOOTING ...................... 54

MAINTENANCE ............................. 56

Handling discs ........................................... 56

SPECIFICATIONS ........................... 57

*Temperature inside the car....

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in the

car becomes normal before operating the unit.

BEFORE USE

*For safety....

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

EN02-04KD-LH1101[E_EX]f.p65 2/26/03, 11:42 AM3

4

ENGLISH

LOCATION OF THE BUTTONS

Control panel

1 (standby/on/attenuator) button

2 TP/PTY (traffic programme/programme type)

button

3 Control dial

4 Display window

5 FM/AM button

6 5 (up) button

7 0 (eject) button

8 4 /¢ buttons

9 (control panel release) button

p SEL (select) button

q D (DISP: display) button

w Number buttons

e M (MODE) button

r Remote sensor

t CD/CD-CH (CD changer) button

y ∞ (down) button

u Trim illumination

Illumination Navigation for easy operations

If you press M (MODE) or SEL (select), the display and some controls (such as the number

buttons, ¢ /4 , 5/∞ , and control dial) enter the corresponding control mode, then the

controls start flashing to lead you to the next operational steps. (Illumination Navigation)

• The display show how these buttons function during this period.

Ex.: When you press number button 1 after pressing M (MODE), to operate the FM tuner.

To use these controls for original functions again, wait until the controls stop flashing without

using these controls.

• Pressing M (MODE) again also restores original functions. However, pressing SEL (select)

makes the unit into a different mode.

Time countdown indicator

71 2 5

p w e

6

r9 q

8

t

3 4

y

u

EN02-04KD-LH1101[E_EX]f.p65 2/27/03, 6:48 PM4

ENGLISH

5

Remote controller

3 • Selects the preset stations while listening to

the radio (or the DAB tuner).

Each time you press the button, the preset

station (or service) number increases, and

the selected station (or service) is tuned in.

• While playing an MP3 disc on an MP3-

compatible CD changer;

– Skips to the previous disc if pressed

briefly.

– Skips to the previous folder if pressed and

held.

Note:

While playing a CD on a CD changer, this

always skips to the previous disc.

4 Selects the sound mode (iEQ: intelligent

equalizer).

Each time you press the button, the sound

mode (iEQ) changes.

5 • Selects the band while listening to the radio

(or the DAB tuner).

Each time you press the button, the band

changes.

• While playing an MP3 disc on an MP3-

compatible CD changer;

– Skips to the next disc if pressed briefly.

– Skips to the next folder if pressed and

held.

Note:

While playing a CD on a CD changer, this

always skips to the next disc.

6 Selects the source.

Each time you press the button, the source

changes.

7 Functions the same as the control dial on the

main unit.

Note:

These buttons do not function for the

preferred setting mode adjustment.

1 • Turns on the unit if pressed when the unit is

turned off.

• Turns off the unit if pressed and held for a

few seconds.

• Drops the volume level in a moment if

pressed briefly.

Press again to resume the volume.

2 • Searches for stations while listening to the

radio.

• Selects services while listening to the DAB

tuner if pressed briefly.

• Searches for ensembles while listening to

the DAB tuner if pressed for more than one

second.

• Fast-forwards or reverses the track/file if

pressed and held while listening to a disc.

• Skips to the beginning of the next track/file

or goes back to the beginning of the current

(or previous) tracks/files if pressed briefly

while listening to a disc.

EN05-06KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM5

ENGLISH

6

Preparing the remote

controller

Before using the remote controller:

• Aim the remote controller directly at the remote

sensor on the main unit. Make sure there is no

obstacle in between.

• Do not expose the remote sensor to strong

light (direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness of

the remote controller decreases, replace the

battery.

1. Remove the battery holder.

1) Push out the battery holder in the direction

indicated by the arrow using a ball-point

pen or a similar tool.

2) Remove the battery holder.

2. Place the battery.

Slide the battery into the holder with the +

side facing upwards so that the battery is

fixed in the holder.

Lithium coin

battery (product

number: CR2025)

Remote sensor

(back side)

3. Return the battery holder.

Insert again the battery holder by pushing it

until you hear a clicking sound.

WARNING:

• Store the battery in a place where children

cannot reach.

If a child accidentally swallows the battery,

consult a doctor immediately.

• Do not recharge, short, disassemble, or heat the

battery or dispose of it in a fire.

Doing any of these things may cause the battery

to give off heat, crack, or start a fire.

• Do not leave the battery with other metallic

materials.

Doing this may cause the battery to give off

heat, crack, or start a fire.

• When throwing away or saving the battery,

wrap it in tape and insulate; otherwise, the

battery may start to give off heat, crack, or start

a fire.

• Do not poke the battery with tweezers or similar

tools.

Doing this may cause the battery to give off

heat, crack, or start a fire.

CAUTION:

DO NOT leave the remote controller in a place

(such as dashboards) exposed to direct sunlight for

a long time. Otherwise, it may be damaged.

KD-LH1101 is equipped with the steering

wheel remote control function.

If your car is equipped with the steering wheel

remote controller, you can operate this

receiver using the controller.

• See the Installation/Connection Manual

(separate volume) for connection to utilize

this function.

(back side)

EN05-06KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM6

7

ENGLISH

4

Adjust the sound as you want. (See

pages 27 – 29.)

Note:

While playing a source, you can also show the level

meter on the display. For details, see “Activating the

level meter” on page 30.

To drop the volume in a moment

Press briefly while listening to any

source. “ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

• If you turn the control dial, you can also restore

the sound.

To turn off the power

Press and hold for more than one

second.

• If you turn off the power while listening to a

disc, disc play will start from where playback

has been stopped previously, next time you

turn on the power.

NOTICE:

The illustrations of the display used in this manual

are mainly of the initial setting when shipped from

the factory. If you have changed the display

patterns or some PSM items, the actual displays

you see will be different.

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step

2

below, the

power automatically comes on. You do not have

to press this button to turn on the power.

2

Select the source.

To operate the tuner (FM or AM),

see pages 10 – 21.

To play a CD,

see pages 22 – 26.

To operate the CD changer,

see pages 40 – 46.

To operate the external component

(LINE IN), see page 47.

To operate the DAB tuner,

see pages 48 – 52.

3

Adjust the volume.

BASIC OPERATIONS

Volume level appears.

To increase the volume

To decrease the volume

Current sound mode (iEQ)

(see page 28)

1 23

EN07-09KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM7

8

ENGLISH

Canceling the display

demonstration

When shipped from the factory, display

demonstration has been activated, and starts

automatically when no operations are done for

about 20 seconds.

• It is recommended to cancel the demonstration

before you use the unit for the first time.

To cancel the display demonstration, follow

the procedure below:

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 31 and 32.)

The next-step-operation

buttons start flashing.

2

Press number button 1 to select

“MOVIE”—Movie category of the

PSM settings.

The “Graphics” setting screen appears on

the display.

3

Select “Off.”

4

Finish the setting.

To activate the display demonstration, repeat

the same procedure and select “Int Demo” or

“All Demo” in step

3

.

• For more details, see “To set the movie

demonstration—Graphics” on page 33.

Off

Int Demo

All Demo

EN07-09KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM8

9

ENGLISH

Setting the clock

You can also set the clock system to either

24 hours or 12 hours.

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 31 and 32.)

The next-step-operation

buttons start flashing.

2

Press number button 2 to select

“CLOCK”—Clock category of the

PSM settings.

The “Clock Hr” (hour) setting screen

appears on the display.

3

Adjust the hour.

4

Set the minute.

1 Select “Clock Min” (minute).

2 Adjust the minute.

12

5

Set the clock system.

1 Select “24H/12H.”

2 Select “24Hours” or “12Hours.”

12

6

Finish the setting.

To check the current clock time when the unit

is turned off, press D (DISP).

The power turns on and the clock time is shown

for 5 seconds, then the power turns off.

EN07-09KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM9

10

ENGLISH

RADIO OPERATIONS

Listening to the radio

You can use either automatic searching or manual

searching to tune in to a particular station.

Searching a station automatically:

Auto search

1

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

2

Start searching a station.

When a station is received, searching stops.

To stop searching before a station is received,

press the same button you have pressed for

searching.

Searching a station manually:

Manual search

1

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

2

Press and hold ¢ or 4

until “Manual Search” starts flashing

on the display.

Selected band appears.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

To search stations of

higher frequencies

To search stations of lower frequencies

FM1 FM2 FM3 AM

FM1 FM2

FM3 AM

EN10-14KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM10

11

ENGLISH

3

Tune in to a station you want while

“Manual Search” is flashing.

• If you release your finger from the button,

the manual mode automatically turns off

after 5 seconds.

• If you hold down the button, the frequency

keeps changing (in 50 kHz intervals for

FM and 9 kHz for AM—MW/LW) until you

release the button.

When an FM stereo broadcast is hard to

receive:

1 Press M (MODE) while listening to an FM

stereo broadcast.

“Mode” appears on the display.

The next-step-operation buttons

start flashing.

2 Press number button 1 to select “Mono On”

while “Mode” is still on the display.

Each time you press the button, “Mono On” and

“Mono Off” appears alternately.

The display returns to the source indication

screen.

To tune in to stations

of higher frequencies

To tune in to stations of lower frequencies

If the sound quality decreases and the

stereo effect is lost while listening to an

FM station

In some areas, adjacent stations may

interfere with each other. If this interference

occurs, this unit can automatically reduce this

interference noise (the initial setting when

shipped from the factory). However, in this

case, the sound quality will be degraded and

the stereo effect will also be lost.

If you do not want to degrade the sound

quality and to lose the stereo effect, rather

than to eliminate the interference noise, see

“To change the FM tuner selectivity—IF Filter”

on page 34.

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM

band (FM1, FM2, and FM3).

1

Select the FM band (FM1 – 3) you

want to store FM stations into.

Each time you press the

button, the band changes as

follows:

FM1 FM2 FM3 AM

CONTINUED ON THE NEXT PAGE

MONO indicator lights up.

After about

5 seconds

EN10-14KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM11

12

ENGLISH

2

Start automatic preset.

1 Press M (MODE).

“Mode” appears on the display.

The next-step-operation

buttons start flashing.

2 Press and hold number button 5, while

“Mode” is still on the display.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number buttons

—No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

1

Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

Each time you press the

button, the band changes as

follows:

FM1 FM2 FM3 AM

“–SSM–” appears, then disappears

when automatic preset is over.

2

Tune in to a station (in this example,

of 92.5 MHz).

3

Press and hold the number button

(in this example, 1) for more than

2 seconds.

4

Repeat the above procedure to store

other stations into other preset

numbers.

Notes:

• A previously preset station is erased when a new

station is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example,

during battery replacement). If this occurs, preset

the stations again.

The display pattern automatically changes

to the small animation display (see page

14). The preset number flashes for about

5 seconds, then the previous display pattern

resumes.

To tune in to stations

of higher frequencies

To tune in to stations of lower frequencies

EN10-14KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM12

13

ENGLISH

Selecting a preset station using the

preset station list

If you forget what stations are stored in what

preset numbers, you can check the preset station

list, then select your desired station.

1

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

2

Press and hold 5 (up) or ∞ (down)

until the preset station list for the

current band (FM1, FM2, FM3, or AM)

appears on the display.

Notes:

• You can show the other FM band preset station lists

(FM1, FM2, or FM3) by pressing 5 (up) or ∞

(down).

• If a preset station is an FM RDS station with PS

signal, PS name will be shown instead of the station

frequency.

3

Select the number (1 – 6) for the

preset station you want.

FM1 FM2 FM3 AM

Tuning in to a preset station

You can easily tune in to a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

stations in memory” on pages 11 and 12.

Selecting a preset station directly

1

Select the band (FM1 – 3, AM).

Each time you press the

button, the band changes as

follows:

2

Select the number (1 – 6) for the

preset station you want.

FM1 FM2 FM3 AM

EN10-14KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM13

14

ENGLISH

Changing the display pattern

By pressing D (DISP), you can change the information shown on the display.

Each time you press the button, the display patterns change as follows:

Large animation display

• When receiving an AM or non FM RDS-

station

• When receiving an FM RDS station (see the

following pages)

Small animation

display 1

Small animation

display 2

Large animation display

Clock time display

PS name

PTY code appears

Current sound

mode (iEQ)

(see page 28)

Clock time

Clock time display

Current sound

mode (iEQ)

(see page 28)

Clock time

Small animation

display

Appears only when

selecting a preset station

EN10-14KD-LH1101[E_EX]f.p65 2/26/03, 11:43 AM14

15

ENGLISH

RDS OPERATIONS

What you can do with RDS

RDS (Radio Data System) allows FM stations to

send an additional signal along with their regular

programme signals. For example, the stations

send their station names, as well as information

about what type of programme they broadcast,

such as sports or music, etc.

Another advantage of RDS function is called

“Enhanced Other Networks.” By using the

Enhanced Other Networks data sent from a

station, you can tune in to a different station of a

different network broadcasting your favorite

programme or traffic announcement while

listening to another programme or to another

source such as CD.

By receiving the RDS data, this unit can do the

following:

• Tracing the same programme automatically

(Network-Tracking Reception)

• Standby Reception of TA (Traffic

Announcement) or your favorite programme

• PTY (Programme Type) search

• Programme search

• And some other functions

Tracing the same programme

automatically (Network-Tracking

Reception)

When driving in an area where FM reception is

not good, the tuner built in this unit automatically

tunes in to another RDS station, broadcasting the

same programme with stronger signals. So, you

can continue to listen to the same programme in

its finest reception, no matter where you drive.

(See the illustration on page 21.)

Two types of the RDS data are used to make

Network-Tracking Reception work correctly

—PI (Programme Identification) and AF

(Alternative Frequency).

Without receiving these data correctly from the

RDS station you are listening to, Network-

Tracking Reception will not operate.

To use Network-Tracking Reception

You can select the different modes of network-

tracking reception to continue listening to the

same programme in its finest reception.

When shipped from the factory, “AF” is selected.

• AF: Network-Tracking Reception is

activated without Regionalization.

With this setting, the unit switches to

another station within the same

network when the receiving signals

from the current station become

weak. (In this mode, the programme

may differ from the one currently

received.)

The AF indicator lights up.

• AF Reg: Network-Tracking Reception is

activated with Regionalization.

With this setting, the unit switches to

another station, within the same

network, broadcasting the same

programme when the receiving

signals from the current station

become weak.

The REG indicator lights up.

• Off: Network-Tracking Reception is

deactivated.

Neither the AF nor the REG indicator

lights up.

Note:

If a DAB tuner is connected and Alternative Reception

(for DAB services) is activated, Network-Tracking

Reception is also activated (“AF”) automatically. On

the other hand, Network-Tracking Reception cannot

be deactivated without deactivating Alternative

Reception. (See page 51.)

AF or REG indicator lights up.

CONTINUED ON THE NEXT PAGE

EN15-21KD-LH1101[E_EX]f.p65 2/26/03, 11:44 AM15

16

ENGLISH

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 31 and 32.)

2

Press number button 4 to select

“TUNER”—Tuner category of the

PSM settings.

The “PTY Stnby” (standby) setting screen

appears on the display.

3

Select “AF-Regn’l” (alternative

frequency/regionalization

reception).

4

Select the desired mode—“AF,”

“AF Reg,” or “Off.”

5

Finish the setting.

Using TA Standby Reception

TA Standby Reception allows the unit to switch

temporarily to Traffic Announcement (TA) from

the current source (another FM station, CD, or

other connected components).

• TA Standby Reception will not work if you are

listening to an AM station.

Press TP/PTY to activate TA

Standby Reception.

Each time your press the button,

this function is turned on and off

alternately.

7 When the current source is FM, the TP

indicator either lights up or flashes.

• If the TP indicator lights up, TA Standby

Reception is activated.

If a station starts broadcasting a traffic

announcement, “Traffic Flash” appears on

the display, and this unit automatically tunes

in to the station. The volume changes to the

preset TA volume level (see page 20) and the

traffic announcement can be heard.

• If the TP indicator flashes, TA Standby

Reception is not yet activated since the

station being received does not provide the

signals used for TA Standby Reception.

To activate TA Standby Reception, you need

to tune in to another station providing these

signals. Press ¢ or 4 to search

for such a station.

When a station providing these signals is

tuned in, the TP indicator stops flashing and

remains lit. Now TA Standby Reception is

activated.

7 When the current source is other than FM,

the TP indicator lights up.

If a station starts broadcasting a traffic

announcement, “Traffic Flash” appears on the

display, and this unit automatically changes the

source and tunes in to the station.

TP indicator appears.

(either lights up or flashes)

EN15-21KD-LH1101[E_EX]f.p65 2/26/03, 11:44 AM16

17

ENGLISH

Using PTY Standby Reception

PTY Standby Reception allows the unit to switch

temporarily to your favorite programme (PTY:

Programme Type) from any source except AM

stations.

To select your favorite PTY code for PTY

Standby Reception

When shipped from factory, PTY Standby

Reception has been set to work for searching for

“News” programmes.

You can select your favorite programme type for

PTY Standby Reception.

1

Press and hold SEL (select) for more

than 2 seconds so that one of the

PSM items appears on the display.

(PSM: see pages 31 and 32.)

2

Press number button 4 to select

“TUNER”—Tuner category of the

PSM settings.

The “PTY Stnby” (standby) setting screen

appears on the display.

3

Select one of the twenty-nine PTY

codes. (See page 21.)

Selected code name

appears on the display

and is stored into

memory.

CONTINUED ON THE NEXT PAGE

4

Finish the setting.

To set PTY Standby Reception

1 Press M (MODE) while listening to an FM

stereo broadcast.

“Mode” appears on the display.

The next-step-operation buttons

start flashing.

2 Press number button 3 to activate PTY

Standby Reception while “Mode” is still on the

display.

Each time you press the button, PTY Standby

Reception turns on and off alternately.

The display returns to the source indication

screen.

Ex.: When the currently selected PTY code

for PTY Standby Reception is “News”

PTY indicator appears.

(either lights up or flashes)

After about

5 seconds

EN15-21KD-LH1101[E_EX]f.p65 2/26/03, 11:44 AM17

18

ENGLISH

Searching your favorite programme

You can search any one of the PTY codes.

In addition, you can store your 6 favorite

programme types in the number buttons.

When shipped from the factory, the following

6 programme types have been stored in the

number buttons (1 to 6).

To store your favorite programme types, see

below and page 19.

To search your favorite programme type, see

page 19.

To store your favorite programme types

1

Press and hold TP/PTY for more

than 2 seconds while listening to an

FM station.

The last selected PTY code

appears.

2

Select one of the twenty-nine PTY

codes. (See page 21.)

Selected code name

appears on the display.

The PTY indicator either lights up or flashes.

• If the PTY indicator lights up, PTY Standby

Reception is activated.

If a station starts broadcasting the selected

PTY programme, this unit automatically tunes

in to the station.

• If the PTY indicator flashes, PTY Standby

Reception is not yet activated since the station

being received does not provide the signals

used for PTY Standby Reception.

To activate PTY Standby Reception, you need

to tune in to another station providing these

signals. Press ¢ or 4 to search for

such a station.

When a station providing these signals is tuned

in, the PTY indicator stops flashing and

remains lit. Now PTY Standby Reception is

activated.

Notes:

After turning on PTY Standby Reception, you can

change the source without canceling PTY Standby

Reception. In this case, the PTY indicator stops

flashing if it was. If a station starts broadcasting the

selected PTY programme, this unit automatically

changes the source and tunes in to the station.

• If you change the source to AM, PTY Standby

Reception will be temporarily canceled.

• You can only deactivate the PTY Standby Reception

when the source is FM.

Pop M

1

2

3

Rock M Easy M

45

6

Classics

Affairs

Varied

Ex.: If you have selected “Pop M” previously

EN15-21KD-LH1101[E_EX]f.p65 2/26/03, 11:44 AM18

19

ENGLISH

3

Press and hold the number button

for more than 2 seconds to store the

PTY code selected into the preset

number you want.

Selected preset number flashes for a while.

4

Press and hold TP/PTY for more than

2 seconds to exit from this mode.

To search your favorite programme type

1

Press and hold TP/PTY for more

than 2 seconds while listening to an

FM station.

The last selected PTY code

appears.

2

To select one of your favorite

programme type

or

To select any one of the twenty-nine

PTY codes

How to use the

5

(up) or

∞

(down) button

By pressing 5 (up) or ∞ (down) repeatedly,

you can show the list of your preset PTY codes

and all twenty-nine PTY codes (six PTY codes

at a time). First, the list of your stored PTY

codes appears, then all twenty-nine PTY codes

(six PTY codes at a time) appears in sequence.

Press the number button to select your desired

PTY code on the list currently shown on the

display.

3

Start PTY search for your favorite

programme.

• If there is a station broadcasting a programme

of the same PTY code as you have selected,

that station is tuned in.

• If there is no station broadcasting a

programme of the same PTY code as you have

selected, the station will not change.

Note:

In some areas, the PTY search will not work correctly.

Ex.: When “Rock M” is selected

or

Ex.: If you have selected “Pop M” previously

EN15-21KD-LH1101[E_EX]f.p65 2/26/03, 11:44 AM19

20

ENGLISH

Setting the TA volume level

You can preset the volume level for TA Standby

Reception. When a traffic programme is received,

the volume level automatically changes to the

preset level.

• See also “Changing the general settings

(PSM)” on pages 31 and 32.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2 Press number button 4 to select “TUNER”—

Tuner category of the PSM settings.

3 Press ¢ or 4 to select “TA Volume.”

4 Turn the control dial to set to the desired

volume.

You can set it from “Volume 0” to “Volume 50.”

5 Press SEL (select) to finish the setting.

Automatic clock adjustment

When shipped from the factory, the clock built in

this unit is set to be readjusted automatically

using the CT (Clock Time) data in the RDS

signal.

If you do not want to use automatic clock

adjustment, follow the procedure below.

• See also “Changing the general settings

(PSM)” on pages 31 and 32.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2 Press number button 2 to select “CLOCK”—

Clock category of the PSM settings.

3 Press ¢ or 4 to select “Auto Adj”

(adjustment).

4 Turn the control dial counterclockwise to select

“Off.”

Now automatic clock adjustment is canceled.

5 Press SEL (select) to finish the setting.

To reactivate clock adjustment, repeat the

same procedure and select “On” in step 4 by

turning the control dial clockwise.

Note:

You must stay tuned to the same station for more than

2 minutes after setting “Auto Adj” to “On.”

Otherwise, the clock time will not be adjusted. (This is

because the unit takes up to 2 minutes to capture the

CT data in the RDS signal.)

Other convenient RDS

functions and adjustments

Automatic selection of the station

when using the number buttons

Usually when you press the number button, the

preset station is tuned in.

However, when the preset station is an RDS

station, something different will happen. If the

signals from that preset station are not sufficient

for good reception, this unit, using the AF data,

tunes in to another frequency broadcasting the

same programme as the original preset station is

broadcasting. (Programme search)

• The unit takes some time to tune in to another

station using programme search.

To activate programme search, follow the

procedure below.

• See also “Changing the general settings

(PSM)” on pages 31 and 32.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items

appears on the display.

2 Press number button 4 to select “TUNER”—

Tuner category of the PSM settings.

3 Press ¢ or 4 to select

“P(Programme)-Search.”

4 Turn the control dial clockwise to select “On.”

Now programme search is activated.

5 Press SEL (select) to finish the setting.

To cancel programme search, repeat the same

procedure and select “Off” in step 4 by turning

the control dial counterclockwise.

EN15-21KD-LH1101[E_EX]f.p65 2/26/03, 11:44 AM20

La page charge ...

JVC KD-LH1101 Le manuel du propriétaire

JVC KD-LH1101 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents