Pioneer X-HM50-S Le manuel du propriétaire

Catégorie
Lecteur CD
Taper
Le manuel du propriétaire

Ce manuel convient également à

11/2/23 X-HM50_Cover.fm
X-HM50-K/-S
CD Receiver System
Système récepteur CD
Sistema receptor de CD
Operating Instructions
Mode d’emploi
Manual de instrucciones
Discover the benefits of registering your product online at
http://www.pioneer.co.uk (or http://www.pioneer.eu).
Découvrez les nombreux avantages offerts en enregistrant votre produit en
ligne maintenant sur
http://www.pioneer.fr (ou http://www.pioneer.eu).
Registre su producto en
http://www.pioneer.es (o en
http://www.pioneer.eu) Descubra los beneficios de registrarse on-line:
11/2/23 X-HM50_Anki_En.fm
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1_A1_En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the rear panel.
D3-4-2-1-4*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 10 cm at top, 10 cm at rear, and 10 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
10 cm 10 cm
10 cm
10 cm
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).
D3-4-2-2-1a_A1_En
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
11/2/23 X-HM50_Anki_En.fm
E-3
9
8
7
6
5
4
3
2
1
Information for users on collection and disposal of old equipment and used batteries
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
K058a_A1_En
Symbol examples
for batteries
Symbol for
equipment
Pb
Condensation
If the player is moved suddenly from a cold place into a
warm room (in winter, for example) or if the
temperature in the room in which the player is installed
rises suddenly due to a heater, etc., water droplets
(condensation) may form inside (on operating parts and
the lens). When condensation is present, the player will
not operate properly and playback is not possible. Let
the player stand at room temperature for 1 or 2 hours
with the power turned on (the time depends on the
extent of condensation). The water droplets will
dissipate and playback will become possible.
Condensation can also occur in the summer if the
player is exposed to the direct wind from an
air-conditioner. If this happens, move the player to a
different place.
S005_A1_En
“Made for iPodand “Made for iPhonemean that an
electronic accessor y has been designed to connect
specifically to iPod, or iPhone, respectively, and has
been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulator y
standards.
iPod and iPhone are a trademarks of Apple Inc.,
registered in the U.S. and other countries.
CAUTION
This product is a class 1 laser product classified
under the Safety of laser products, IEC 60825-1:2007,
but this product contains a laser diode higher than
Class 1. To ensure continued safety, do not remove
any covers or attempt to gain access to the inside of
the product.
Refer all servicing to qualified personnel.
The
following caution label appears on your unit.
Location: Inside of the unit
D58-5-2-2b*_A1_En
CLASS 1 LASER PRODUCT
Laser Diode Properties
Material: AIGaAs
Wavelength: 790 nm
Emission Duration: continuous
Laser Output: max. 0.7 mW
11/2/23 X-HM50_En.fm
En-4
l X-HM50 CD Receiver System consisting of main unit and speaker system.
Introduction
Thank you for purchasing this PIONEER product. To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your PIONEER product.
Special Note
Supply of this product does not convey a license nor imply any right to distribute content created with this product in
revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue-generating
streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution
systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact
discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for
such use is required. For details, please visit http://mp3licensing.com
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
Accessories
Please confirm that the following accessories are included.
Page
General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 8
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the clock (Remote control only) . . . . . . . . . . 9 - 10
iPod and iPhone
Listening to the iPod or iPhone . . . . . . . . . . . . . . . 10 - 11
CD or MP3/WMA disc Playback
Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . 12
Advanced CD or MP3/WMA disc playback . . . . . . 13 - 14
MP3/WMA folder mode
(only for MP3/WMA files) . . . . . . . . . . . . . . . . . . . . 14 - 15
Page
USB
Listening to USB mass storage
device/MP3 player . . . . . . . . . . . . . . . . . . . . . . . . .15 - 16
Advanced USB playback . . . . . . . . . . . . . . . . . . . . . . . 16
Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Advanced Features
Using the Radio Data System (RDS) . . . . . . . . . . 18- 20
Timer and sleep operation
(Remote control only) . . . . . . . . . . . . . . . . . . . . . 21 - 22
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . 23
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . .23 - 24
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
iPhone adaptors x 3 Remote control x 1 “AAA” size battery
(UM/SUM-4, R3, HP-16
or similar) x 2
AM loop aerial x 1
Warranty card
These operating instructions
FM aerial x 1 Speaker wires x 2
CONTENTS
ENGLISH
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-5
Precautions
l Use the unit on a firm, level surface free from vibration.
l Place the speakers at least 30 cm away from any CRT
TV to avoid colour variations across the TV screen. If
the variations persist, move the speakers further away
from the TV. LCD TV is not prone to such variation.
l Keep the unit away from direct sunlight, strong
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home computers,
facsimiles, etc.) which generate electrical noise.
l Do not place anything on top of the unit.
l Do not expose the unit to moisture, to temperatures
higher than 60°C (140°F) or to extremely low
temperatures.
l If your system does not work properly, disconnect the
AC power lead from the wall socket. Plug the AC power
lead back in, and then turn on your system.
l In case of an electrical storm, unplug the unit for safety.
l Hold the AC power plug by the head when removing it
from the wall socket, as pulling the lead can damage
internal wires.
l The AC power plug is used as a disconnect device and
shall always remain readily operable.
l Do not remove the outer cover, as this may result in
electric shock. Refer internal service to your local
PIONEER service facility.
l The ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers,
tablecloths, curtains, etc.
l No naked flame sources, such as lighted candles,
should be placed on the apparatus.
l Attention should be drawn to the environmental aspects
of battery disposal.
l The apparatus is designed for use in moderate
climates.
Warning:
The voltage used must be the same as that specified on
this unit. Using this product with a higher voltage other
than that which is specified is dangerous and may result in
a fire or other type of accident causing damage. PIONEER
will not be held responsible for any damage resulting from
use of this unit with a voltage other than that which is
specified.
The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It is
advisable to avoid exposure to high volume levels. Do not
turn the volume on to full at switch on. Listen to music at
moderate levels. Excessive sound pressure from
earphones and headphones can cause hearing loss.
Controls and indicators
Page
1. Remote sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. Timer indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3. Disc Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. iPod or iPhone Docking Station . . . . . . . . . . . . . 10
5. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. STANDBY/ON Button. . . . . . . . . . . . . . 9, 11, 12, 17
7. INPUT Button . . . . . . . . . . . . . . . . . . . 11, 12, 15, 17
8. Headphone Socket . . . . . . . . . . . . . . . . . . . . . . . 23
9. Audio In Socket . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Page
10. USB Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
11. Tuner Preset Down, CD/USB Track Down,
iPod/iPhone Skip Down . . . . . . . . . . . . . . . . . 11, 12
12. Tuner Preset Up, CD/USB Track Up,
iPod/iPhone Skip Up . . . . . . . . . . . . . . . . . . . 11, 12
13. Disc/USB Stop Button . . . . . . . . . . . . . . . . . . . . . 12
14. Disc/USB/iPod/iPhone Play or
Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . 11, 12
15. Disc Tray Open/Close Button . . . . . . . . . . . . . . . 12
n General
n Volume control
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
1
9
6
7
8 10 11 12 13 14 15
52 3
4
n Front panel
11/2/23 X-HM50_En.fm
En-6
Controls and indicators (continued)
Page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . 8
2. STANDBY/ON Button . . . . . . . . . . . . . . 9, 11, 12, 21
3. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . 17, 18
4. RDS ASPM Button . . . . . . . . . . . . . . . . . . . . . . . . 18
5. Mute Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. Direct Search Buttons . . . . . . . . . . . . . . . . . . . . . 13
7. iPod/iPhone DISPLAY TV OUT Button . . . . . . . . 11
8. Disc/USB Display Button. . . . . . . . . . . . . . . . . . . 15
9. Tuning Down, Skip Down, Fast Reverse,
Time Down Button . . . . . . . . . . 9, 11, 12, 15, 17, 21
10. Tuner Preset Up Button,
iPod Cursor Up. . . . . . . . . . . . . . . . . . . . . 11, 15, 17
11. Volume Down Button . . . . . . . . . . . . . . . . . . . . . . . 9
12. Tuner Preset Down Button,
iPod Cursor Down . . . . . . . . . . . . . . . . . . 11, 15, 17
13. Equalizer Mode Button . . . . . . . . . . . . . . . . . . . . . 9
14. iPod/iPhone Button . . . . . . . . . . . . . . . . . . . . . . . 11
15. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
16. Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 12
17. RDS Display Button . . . . . . . . . . . . . . . . . . . . . . 18
18. RDS PTY Button. . . . . . . . . . . . . . . . . . . . . . . . . . 18
19. EXTRA BASS Button . . . . . . . . . . . . . . . . . . . . . . . 9
20. Bass/Treble Button . . . . . . . . . . . . . . . . . . . . . . . . 9
21. Memory Button. . . . . . . . . . . . . . . . . . . . . . . . 13, 17
22. Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
23. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . 9, 21
24. Sleep Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
25. Folder Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
26. Play Mode Button. . . . . . . . . . . . . . . . . . . . . . . . . 13
27. iPod/iPhone Play/Pause Button . . . . . . . . . . . . . 11
28. iPod/iPhone Menu Button . . . . . . . . . . . . . . . . . . 11
29. Disc/USB Play/Pause Button . . . . . . . . . 12, 13, 15
30. Disc/USB Stop Button . . . . . . . . . . . . . . 12, 15, 16
31. Tuning Up, Skip Up, Fast Forward,
Time Up Button . . . . . . . . . . . . 9, 11, 12, 15, 17, 21
32. Volume Up Button . . . . . . . . . . . . . . . . . . . . . . . . . 9
33. Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 21
34. Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 9
35. Audio/Line (INPUT) Button . . . . . . . . . . . . . . . 8, 23
36. USB Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Page
1. USB Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2. iPod Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3. CD Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4. MP3 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6. RDM (Random) Indicator. . . . . . . . . . . . . . . . . . . 13
7. MEM (Memory) Indicator . . . . . . . . . . . . . . . . . . . 13
8. Repeat Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . 13
9. Play/Pause Indicator . . . . . . . . . . . . . . . . . . . . . . 12
10. Tuning FM/AM Indicator . . . . . . . . . . . . . . . . . . . 17
11. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . 17
12. Stereo Station Indicator . . . . . . . . . . . . . . . . . . . 17
13. RDS Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
14. PTY Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
15. TP Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
16. TA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
17. Muting Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
18. Title Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
19. Artist Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
20. Folder Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 15
21. Album Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 15
22. File Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
23. Track Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
24. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . 21
25. Once Timer Indicator . . . . . . . . . . . . . . . . . . . . . . 21
26. Disc Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
27. Total Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
28. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
n Speaker system
1. Dome-Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Terminal
n Speaker grilles are removable
Make sure nothing comes into contact
with the speaker diaphragms when
you remove the speaker grilles.
25
26
30
34
33
24
21
16
17
18
22
23
8
9
10
11
12
13
15
14
4
2
3
5
6
1
20
19
7
32
27
31
29
36
35
28
1 4 5 6 7
8
9
10 11 1312 14
15
16
28272624 2523221918 2120
17
2 3
2
1
3
4
n Remote control
n Display
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-7
System connections
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 ohms socket and
position the FM aerial wire in the direction where the
strongest signal can be received.
External FM aerial:
Use an external FM aerial (75 ohms coaxial cable) for
better reception. When an external FM aerial is used,
disconnect the supplied FM aerial wire.
Supplied AM loop aerial:
Connect the AM loop aerial to the AM terminal. Position
the AM loop aerial for optimum reception. Place the AM
loop aerial on a shelf, etc., or attach it to a stand or a wall
with screws (not supplied).
Note:
Placing the aerial on the unit or near the AC power lead
may cause noise pickup. Place the aerial away from the
unit for better reception.
Photo and video files from iPod or iPhone can be viewed
by connecting the system to TV/monitor.
If the TV/monitor has a video input, connect it to the VIDEO
OUT socket at the back of the unit and set the TV Out on
the iPod or iPhone unit to “ON” position.
Note:
Please make sure to set iPod unit to either NTSC or PAL to
match your TV signal. Please visit Apple’s homepage for
further information.
After checking all the connections have been made
correctly, plug the AC power lead of this unit into the wall
socket.
Note:
Unplug the AC power lead from the wall socket if the unit
will not be in use for a prolonged period of time.
CAUTION
Handle the power cord by the plug part. Do not pull out the
plug by tugging the cord, and never touch the power cord
when your hands are wet, as this could cause a short
circuit or electric shock. Do not place the unit, a piece of
furniture, or other object on the power cord or pinch the
cord in any other way. Never make a knot in the cord or tie
it with other cables. The power cords should be routed so
that they are not likely to be stepped on. A damaged power
cord can cause a fire or give you an electric shock. Check
the power cord once in a while. If you find it damaged, ask
your nearest Pioneer authorized independent service
company for a replacement.
Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.
Right
speaker
FM aerial
To video input socket
screws (not supplied)
wall
< Attaching
to the wall >
< Assembling >
Wall socket
(AC 220 V to 230 V,
50 Hz/60 Hz)
Installing the AM loop aerial
Video cable
(not supplied)
TV
AM loop
aerial
Left
speaker
n Aerial connection
n Speaker connection
l
Twist exposed wire strands together.
l Connect the red wire to the plus
(+) terminal, and other wire to the
minus (–) terminal.
l Use speakers with an impedance
of 4 ohms - 16 ohms, as lower
impedance speakers can damage
the unit.
l
These speaker terminals carry HAZARDOUS LIVE voltage.
To prevent the risk of electric shock when connecting or
disconnecting the speaker cables, disconnect the power
cord before touching any uninsulated parts.
l Do not attach these speakers to the wall or ceiling, as
they may cause injury in the event of a fall.
l
Do not mistake the right and the left channels. The right
speaker is the one on the right side when you face the unit.
l Do not let the bare speaker wires touch each other.
l Do not allow any objects to fall into or to be placed in
the bass reflex ducts.
l
Do not stand or sit on the speakers. You may be injured.
l
Do not connect the supplied speakers with any other
amplifier. This may result in malfunction or fire.
Incorrect
n Connecting iPod or iPhone to TV
n AC power connection
11/2/23 X-HM50_En.fm
En-8
System connections (continued)
You can connect a subwoofer with an amplifier to the
SUBWOOFER PRE OUT socket.
Notes:
l
No sound is heard from the subwoofer without a built-in
amplifier.
l
Subwoofer Pre-out (audio signal): 350 mV / 10 k ohms at
70 Hz.
Connect to the TV using an audio cable
.
To select Line In function:
l
On main unit: Press INPUT button repeatedly until
Line In is displayed.
l
On remote control: Press AUDIO/LINE (INPUT) button
repeatedly until Line In is displayed.
Remote control
WARNNIG:
l Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
Caution:
l When inserting the batteries, make sure not to damage
the springs on the battery’s (
) terminals.
l
Replace all old batteries with new ones at the same time.
l
Do not mix old and new batteries.
l
Remove the batteries if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
l
Do not use rechargeable batteries (nickel-cadmium
battery, etc.).
l
Installing the batteries incorrectly may cause the unit to
malfunction.
Notes concerning use:
l
Replace the batteries if the operating distance is reduced
or if the operation becomes erratic. Purchase 2 “AAA” size
batteries (UM/SUM-4, R3, HP-16 or similar).
l
Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
l
Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the
direction of the unit if this occurs.
l
Keep the remote control away from moisture, heat, shock,
and vibrations.
l When disposing of used batteries, please comply with
governmental regulations or environmental public
instruction's rules that apply in your country or area.
Check the remote control after checking all the connections.
Point the remote control directly at the remote sensor on the
unit. The remote control can be used within the range shown
below:
n Using other subwoofer
n Connecting a TV, etc.
Audio cable
(commercially
available)
Audio signal
To audio input
socket
To SUBWOOFER PRE
OUT socket
Main unit
Commercially available subwoofer
(amplifier built in)
Audio signal
TV
To audio
output sockets
Audio cable
(commercially
available)
Main unit
To L INE
input
sockets
n Battery installation
1
Open the battery cover.
2
Insert the supplied batteries according to the direction
indicated in the battery compartment.
When inserting or removing the batteries, push them
towards the (–) battery terminals.
3
Close the cover.
n Test of the remote control
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-9
General control
Press the STANDBY/ON button to turn the power on.
To dim the display brightness, press the DIMMER button on the
remote control.
If you turn off and on the main unit with the volume set to 27 or higher,
the volume starts at 16 and fades in to the last set level.
Turn the volume knob towards VOLUME (on main unit) or press VOL
+/– (on remote control) to increase or decrease the volume.
When you press any of the following buttons, the unit turns on.
l
iPod / iPhone, CD, USB, AUDIO / LINE (INPUT), TUNER (BAND)
on the remote control: Selected function is activated.
l
/ button on the main unit: The unit turns on and playback of
the last function will start (CD, TUNER, USB, iPod, AUDIO IN,
LINE IN)
The main unit will enter the stand-by mode (when iPod/iPhone is not
docked) after 15 minutes of inactivity during:
iPod/iPhone: No connection or in the pause mode.
CD / USB: In the stop mode.
The volume is muted temporarily when pressing the MUTE button on
the remote control. Press again to restore the volume.
When the power is first turned on, the unit will enter the extra bass
mode which emphasises the bass frequencies. To cancel the extra
bass mode, press the EXTRA BASS button on the remote control.
1
Press the BASS/TREBLE button to select “Bass”.
2
Within 5 seconds, press the VOL (+ or –) button to adjust the bass.
1
Press the BASS/TREBLE button to select “Treble”.
2
Within 5 seconds, press the VOL (+ or –) button to adjust the
treble.
When the INPUT button on main unit is pressed, the current function
will change to different mode. Press the INPUT button repeatedly to
select desired function.
Note:
The backup function will protect the memorised function mode for a
few hours should there be a power failure or the AC power lead
becomes disconnected.
Setting the clock (
Remote
control only)
In this example, the clock is set for the 24-hour (00:00) display.
n To turn the power on
After use:
Press the STANDBY/ON button to enter the power stand-by mode.
Note:
However, if iPod/iPhone is docked, the unit will begin charging.
“iPod charge” will be displayed.
n Display brightness control
n Volume auto fade-in
n Volume control
n Auto power on function
n Auto power off function
n Muting
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
INPUT
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display gets dimmer).
(Display is bright).
n Extra-Bass control
n Bass control
n Treble control
n Equaliser
n Function
1
Press the STANDBY/ON button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust the day,
press the or button and then press the ENTER button.
4
Press the or button to select 24-hour or 12-hour display
and then press the ENTER button.
The 24-hour display will appear.
(00:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 00:00 - PM 11:59)
Pops
Vocal
Jazz
Flat
Game
Classic
For rock music.
For pop music.
No equalization.
For classical music.
For jazz.
Vocals are enhanced.
Equaliser off.
For game.
For classical music.
For pop music.
Vocals are enhanced.
For jazz.
When the EQUALIZER MODE
button is pressed, the current
mode setting will be displayed.
To change to a different mode,
press the EQUALIZER MODE
button repeatedly until the
desired sound mode appears.
FM STEREO
FM MONO
USB
iPod
Audio In
Line In
CD AM
11/2/23 X-HM50_En.fm
En-10
Setting the clock (Remote control
only) (continued)
To confirm the time display:
Press the CLOCK/TIMER button. The time display will appear
for about 5 seconds.
Note:
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock (pages 9 - 10).
To readjust the clock:
Perform “Setting the clock” from step 1. If the “Clock” does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
Listening to the iPod or iPhone
Supported iPod and iPhone models:
l
iPod touch (1
st
/2
nd
/3
rd
/4
th
generation)
l
iPod classic
l
iPod nano (2
nd
/3
rd
/4
th
/5
th
/6
th
generation)
l
iPhone 4
l
iPhone 3GS
l
iPhone 3G
l
iPhone
Notes:
l Audio from the iPod/iPhone cannot be heard via the
headphones connected to the unit.
l
Once the iPod or iPhone is connected to the unit it will
begin charging.
l
Error message “This accessory is not made to work with
iPhone” may appear on the iPhone screen when iPhone
battery is low.
l
The message “This accessory is not made to work with
iPhone” or “This accessory is not supported by iPhone”
may appear on the iPhone screen when the iPhone is not
properly docked (eg. slanting) on this product. If this
occurs, please remove and re-dock the iPhone.
l
To prevent random interference when iPod/iPhone
function is selected, the headphone output is
disabled.
You may also experience brief audio interference
during incoming calls.
Notes:
l
Please use the adaptor supplied with your iPod or iPhone
unit.
l
You can use an audio cable to connect your iPod to the
AUDIO IN socket if:
1.
your iPod adaptor does not fit into the iPod dock on the
main unit.
2.
you have an iPod that does not have an iPod adaptor.
3.
you have an iPod that does not have an iPod 30 pin
connector.
Caution:
Unplug all accessories from the iPod or iPhone before
inserting it into the dock.
5
To adjust the hour, press the or button and then
press the ENTER button. Press the or button
once to advance the time by 1 hour. Hold it down to
advance continuously.
6
To adjust the minutes, press the or button and
then press the ENTER button. Press the or
button once to advance the time by 1 minute.
1 Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 24 for details.]
2 Perform “Setting the clock” from step 1 onwards.
n iPod and iPhone adaptor connection
iPhone
Adaptor No.
iPhone
Description
Capacity
12 iPhone 4GB & 8GB & 16GB
15 iPhone 3G,
iPhone 3GS
8GB & 16GB & 32GB
& 64GB
19 iPhone 4 16GB & 32GB
n To insert iPod or iPhone adaptor
1
Open the iPod cover by pulling up.
2 Insert the iPod or iPhone adaptor into unit and connect
your iPod or iPhone.
n To remove iPod or iPhone adaptor
Insert the tip of a screwdriver (“–” type,
small) into the adaptor hole as shown
and lift upward to remove.
n iPod or iPhone playback
1
Press the STANDBY/ON button to turn the power on.
2
Press the iPod/iPhone button on the remote control or INPUT
button repeatedly on the main unit to select iPod function.
3
Insert iPod or iPhone unit in iPod dock of main unit.
4
Press the / (iPod/iPhone / ) button to start playback.
iPhone
Dock connector
iPhone (bottom)
iPhone dock
iPhone connector
iPhone adaptor
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-11
Listening to the iPod or iPhone (continued)
l
Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately 10
seconds.
l
Incoming calls will pause the playback and iPhone ringtones
will be heard from the main unit speakers only.
l
Once the calls are answered, the conversation can only be
heard through the built-in iPhone speaker. Turn on the
iPhone speaker or undock the iPhone to start conversation.
Simply remove the iPod or iPhone from the iPod dock. It is safe
to do so even during playback.
Note:
When navigating the iPod or iPhone menu with remote control, do
not operate any of the buttons on the iPod or iPhone unit. The
volume level is adjusted by pressing the VOL (+ or –) button on
the main unit or the remote control. Adjusting the volume on the
iPod and iPhone units give no effect.
iPod and iPhone operations:
The operations described below depend on the generation iPod
and iPhone you are using.
System on operation:
When the main unit is powered on, the iPod and iPhone units will
automatically power on when docked in the unit.
System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked iPod
and iPhone unit will automatically turn to stand-by mode.
Notes:
l
If the TV Out setting is already turned on at video menu, the
video is automatically displayed on the TV screen when
ENTER key is pressed.
l
To return to watching video on iPod or iPhone screen, press
the MENU button to enter video menu. Then press the
DISPLAY TV OUT button for more than 2 seconds until “iPod
Display” appears.
l
During iPod or iPhone video playback, pressing the DISPLAY
TV OUT button will not toggle video out display between iPod
and TV.
Caution:
l
Unplug all accessories for the iPod or iPhone before inserting
it into the iPod dock.
n iPhone playback
n To disconnect iPod or iPhone
n Navigating the iPod and iPhone menus
1
Press the MENU button to view the menu on iPod or iPhone
unit. Press it again to go back to previous menu.
2
Use the PRESET (
or
) button to select an item on the
menu and then press ENTER button.
STANDBY/ON
INPUT
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
n Watching videos on a TV connected to
iPod or iPhone
1
Press the DISPLAY TV OUT button for more than 2 seconds.
“TV Display” will appear on display.
2
Press the ENTER button to start playback.
n Various iPod functions
Function Main
unit
Remote
control
Operation
Play
Press in the pause
mode.
Pause
Press in the playback
mode.
Track up/
down
Press in the playback or
pause mode.
If you press the button in
the pause mode, press
the / button to start
the desired track.
Fast
forward/
reverse
Press and hold down in
the playback mode.
Release the button to
resume playback.
Display
____
iPod back light ON.
Press for more than 2
seconds to toggle the
video out display
between iPod or TV.
Repeat
____
Press to toggle repeat
mode.
Shuffle
____
Press and hold down to
toggle shuffle mode.
iPod
Menu
____
Press to view the iPod
menu during iPod
function.
iPod
Enter
____
Press to confirm the
selection.
iPod
Cursor
Up/Down
____
Press to select the iPod
menu.
11/2/23 X-HM50_En.fm
En-12
Listening to a CD or MP3/WMA disc
This system can play back a standard CD, CD-R/RW in the CD
format and CD-R/RW with MP3 or WMA files, but cannot record
on them. Some audio CD-R and CD-RW discs may not be
playable due to the state of the disc or the device that was used
for recording.
MP3:
MP3 is a form of compression. It is an acronym which stands
for MPEG Audio Layer 3. MP3 is a type of audio code which
is processed by significant compression from the original
audio source with very little loss in sound quality.
l
This system supports MPEG 1 Layer 3 and VBR files.
l
During VBR file playback, time counter in the display may
differ from its actual playback time.
l
Bitrate which is supported by MP3 is 32 kbps to 320 kbps.
WMA:
WMA files are Advanced System Format files that include
audio files which are compressed with Windows Media
Audio codec. WMA is developed by Microsoft as an audio
format file for Windows Media Player.
l
“MP3” and “WMA” indicator will light up after the unit reads
information on an MP3 or WMA disc.
l
Bitrate which is supported by WMA is 64 kbps to 160 kbps.
Caution:
l
Do not place two discs in one disc tray.
l
Do not play discs of special shapes (heart, octagon, etc). It
may cause malfunctions.
l
Do not push the disc tray whilst it is moving.
l
If the power fails whilst the tray is open, wait until the power
is restored.
l
If TV or radio interference occurs during CD operation, move
the unit away from the TV or radio.
l
Be sure to place 8 cm disc in the middle of the disc tray.
l
Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
STANDBY/ON
INPUT
n Disc playback
1
Press the STANDBY/ON button to turn the power on.
2
Press the CD button on the remote control or INPUT button
repeatedly on the main unit to select CD function.
3
Press the button to open the disc tray.
4
Place the disc on the disc tray, label side up.
5
Press the button to close the disc tray.
6
Press the
/
(CD/USB
/
) button to start playback. After
the last track is played, the unit will stop automatically.
n Various disc functions
Function Main
unit
Remote
control
Operation
Play
Press in the stop mode.
Stop
Press in the playback
mode.
Pause
Press in the playback
mode. Press the /
button to resume
playback from the
paused point.
Track
up/
down
Press in the playback or
stop mode.
If you press the button in
the stop mode, press the
/ button to start the
desired track.
Fast
forward/
reverse
Press and hold down in
the playback mode.
Release the button to
resume playback.
PHONES
AUDIO IN
USB
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-13
Advanced CD or MP3/WMA disc playback
By using the Direct Search buttons, the desired tracks on the
current disc can be played.
Use the Direct Search buttons on the remote control to
select the desired track whilst playing the selected disc.
l
The Direct Search buttons allow you to select up to
number 9.
l
When selecting number 10 or higher, use the “>10” button.
Notes:
l
A track number higher than the number of tracks on the
disc cannot be selected.
l
During random play, direct search is not possible.
To stop playback:
Press the (CD/USB ) button.
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press the PLAY MODE button repeatedly until “Repeat One”
appears. Press the / (CD/USB / ) button.
To repeat all tracks:
Press the PLAY MODE button repeatedly until “Repeat All”
appears. Press the / (CD/USB / ) button.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play” section on this page
and then press the PLAY MODE button repeatedly until
“Repeat All” appears.
To cancel repeat play:
Press the PLAY MODE button repeatedly until “Normal”
appears and ” disappears.
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
Whilst in the stop mode, press and hold down PLAY MODE
button on the remote control until “Random” appears. Press the
/ (CD/USB /) button.
To cancel random play:
Press the (CD/USB ) button.
Notes:
l
If you press the button during random play, you can
move to the track selected next by the random operation.
On the other hand, the button does not allow you to move
to the previous track. The beginning of the track being
played will be located.
l
In random play, the unit will select and play tracks
automatically. (You cannot select the order of the tracks.)
Caution:
After performing repeat play, be sure to press the (CD/USB
) button. Otherwise, the disc will play continuously.
You can choose up to 32 selections for playback in the order
you like.
n Direct track search
A. For example, to choose 13
1
Press the “>10” button once.
2
Press the “1” button.
3
Press the “3” button.
B. For example, to choose 130
1
Press the “>10” button twice.
2
Press the “1” button.
3
Press the “3” button.
4
Press the “0” button.
n Repeat play
Selected track number
n Random play
n Programmed play (CD)
1
Whilst in the stop mode, press the MEMORY button on the
remote control to enter the programming save mode.
2
Press the or buttons on the remote control to
select the desired track.
3
Press the MEMORY button to save the track number.
4
Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be
programmed. If you want to check the programmed tracks,
press the MEMORY button repeatedly. If you make a
mistake, the programmed tracks can be cleared by
pressing the CLEAR button.
5
Press the / (CD/USB / ) button to start playback.
Selected track number
11/2/23 X-HM50_En.fm
En-14
Advanced CD or MP3/WMA disc
playback (continued)
To cancel the programmed play mode:
Press the (CD/USB ) button. The display will show
“Memory Clear” and all the programmed contents will be
cleared.
Adding tracks to the programme:
If a programme has been previously stored, the “MEM”
indicator will be displayed. Press the MEMORY button
repeatedly to go to the last programme memory. Then
follow steps 2 - 3 to add tracks. The new tracks will be
stored after the last track of the previous programme.
Notes:
l When a disc is ejected, the programme is automatically
cancelled.
l If you press the STANDBY/ON button to enter the
stand-by mode or change the function from CD to
another, the programmed selections will be cleared.
l During the programme operation, random play is not
possible.
MP3/WMA folder mode (only for MP3/
WMA files)
To play back MP3/WMA (Windows Media Audio) file
There are many music sites on the internet that you can
download MP3/WMA (Windows Media Audio) music files.
Follow the instructions from the website on how to
download the music files. You can then play back these
downloaded music files by burning them to a CD-R/RW
disc.
l Your downloaded song/files are for personal use only.
Any other usage of the song without owner’s
permission, is against the law.
If MP3/WMA files are recorded in several folders, a folder
number will be set to each folder automatically.
These folders can be selected by the FOLDER button on
the remote control. If there is no supported file formats
inside the selected folder, the folder is skipped and the next
folder will be selected.
Example: How to set folder number if MP3/WMA format
files are recorded as below figure.
l The folder and file order information which is recorded
on the disc depends on the writing software. There
maybe possibilities that this unit will playback the files
not according to our expected playback order.
l For CD MP3/WMA, 255 numbers of folders and files
inclusive of the folders which have non playable files
can be read.
Folder mode on/off can be operated by the FOLDER
button on the remote control. Files that are played when
folder mode is set to the on position, may differ from those
played back when folder mode is turned off.
n Programmed play (MP3/WMA)
1
Whilst in the stop mode, press the MEMORY button to
enter the programming save mode.
2 Press the PRESET
(
or
)
button on the remote
control to select the desired folder.
Then press the or button on the remote control
to select the desired tracks.
3 Press the MEMORY button to save the folder and track
number.
4 Repeat steps 2 - 3 for other folder/tracks. Up to 32
tracks can be programmed.
5 Press the / (CD/USB / ) button to start playback.
n About folder playback order
1
ROOT folder is set as folder 1.
2 As for folders inside ROOT folder (Folder A and Folder
B), the folder which is recorded earlier on the disc will be
set as folder 2 and folder 3.
3 As for folder inside Folder A (Folder C and Folder D), the
folder which is recorded earlier on the disc will be set as
folder 4 and folder 5.
4 Folder E that is inside Folder D will be set as folder 6.
ROOT
(FOLDER 1)
FOLDER A
(FOLDER 2)
FOLDER B
(FOLDER 3)
FILE 9
FILE 10
FILE 3
FILE 4
FILE 5
FILE 6
FILE 7
FILE 8
FOLDER E
(FOLDER 6)
FOLDER C
(FOLDER 4)
FOLDER D
(FOLDER 5)
FILE 1
FILE 2
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-15
MP3/WMA folder mode (only for MP3/
WMA files) (continued)
To play back CD-R/RW.
Note:
If “Not Support” is displayed, it means “Copyright protected
WMA file” or “Not supported playback file” is selected.
Listening to USB mass storage
device/MP3 player
Notes:
l This USB mass storage device or MP3 player is not
compatible with MTP and AAC file systems.
l Some external storage devices may not operate with
this system.
l Operation of external storage devices (USB memory
devices, external hard disks, etc.) is not guaranteed.
Note:
To pause playback:
Press the / (CD/USB / ) button.
n Procedure to playback MP3/WMA disc with
folder mode on
1
Press the CD button, and load an MP3/WMA disc.
Press the FOLDER button and disc info will be
displayed.
2 Press the PRESET
(
or
)
button to select desired
playback folder. (Folder mode on)
3 Select desired file to be played back by pressing the
or button.
4 Press the / (CD/USB / ) button. Playback will start
and file name will be displayed.
l Title, Artist and Album name are displayed if they are
recorded on the disc.
l Display content can be changed by pressing the
DISPLAY button.
MP3 indicator
WMA indicator
TOTAL indicator
Total number of files
Total number of folder
First track number
in the folder
FOLDER
indicator
FOLDER number
File name display Folder display
Title display
Album display
Counter display
Artist display
n To play back USB/MP3 player with folder
mode off
1
Press the USB button on the remote control or INPUT
button repeatedly on main unit to select USB function.
Connect the USB memory device that has MP3/WMA
format files on the unit. When the USB memory is
connected to the main unit, the device information will
be displayed.
2 Select desired file to be played back by pressing the
or button.
3 Press the / (CD/USB / ) button. Playback will start
and the file name will be displayed.
l Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
l Display content can be changed by pressing the
DISPLAY button.
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
INPUT
11/2/23 X-HM50_En.fm
En-16
Listening to USB mass storage device/MP3 player (continued)
Notes:
l PIONEER will not be held liable for the loss of data
whilst the USB memory device is connected to the
audio system.
l Files compressed in MP3 and/or WMA format can be
played back when connected to the USB terminal.
l This USB memory’s format supports FAT 16 or FAT 32.
l PIONEER cannot guarantee that all USB memory
devices will work on this audio system.
l USB cable is not recommended for use in this audio
system to connect to USB memory device. Use of the
USB cable will affect the performance of this audio
system.
l This USB memory cannot be operated via USB hub.
l The USB terminal in this unit is not intended for a PC
connection but is used for music streaming with a USB
memory device.
l External HDD-storage cannot be played back via USB
terminal.
l If the data inside the USB memory is large, it may take
longer time for the data to be read.
l This product can play WMA and MP3 files. It will
automatically detect the file type being played. If
unplayable file is played on this product, “Not Support”
is indicated and the file will be automatically skipped.
This will take a few seconds. If abnormal indications
appear on the display due to the unspecified file, turn
off the unit and then turn it on again.
l This product relates to USB mass storage devices and
MP3 players. It may however face some irregularities
due to various unforeseen reasons from some devices.
Should this happen, turn off the unit and then turn it on
again.
l The USB port is only intended for direct connection to
a USB memory device without any cable.
l During CD function, MP3 player will not be charging.
l “Not support” will be displayed if you connect an iPod to
USB terminal when the USB function is selected.
Advanced USB playback
The following functions are the same as CD
operations:
Page
Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programmed play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Note:
If USB memory device is not connected, “No USB” will be
shown on the display.
Notes:
l This unit only supports “MPEG-1 Audio Layer-3”
format. (Sampling Frequency is 32 kHz, 44.1 kHz, 48
kHz)
l Playback order for MP3 files may differ depending on
the writing software used during file download.
l Bitrate which is supported by MP3 is 32 kbps to 320
kbps, WMA is 64 kbps to 160 kbps.
l For MP3/WMA files, please put “.MP3” “.WMA”
extension. Files cannot be played back if there is no
MP3/WMA extension.
l Playlists are not supported on this unit.
l This unit can display Folder Name or File Name up to
32 characters.
l Maximum total number of MP3/WMA files is 1024.
Maximum total number of folders is 255 inclusive of
root directory.
l The display playback time may not be displayed
correctly when playing back a variable bitrate file.
l The ID3TAG information supported are TITLE, ARTIST
and ALBUM only. Title name, artist name and album
name can be displayed by pressing the DISPLAY
button during file playback or pause mode.
l WMA meta tag also supports title, artist and album
name which are recorded in WMA files. Copyright
protected WMA files cannot be played back.
n To play back USB/MP3 player with folder
mode on
1
Press the USB button on the remote control or INPUT
button repeatedly on main unit to select USB function.
Connect the USB memory device that has MP3/WMA
format files on the unit. When the USB memory is
connected to the main unit, the device information will
be displayed.
2 Press the FOLDER button, and press the PRESET
(
or
)
button to select desired playback folder. To start
playback with folder mode on, go to step 4. To change
the playback folder, press the PRESET
(
or
)
button
to select another folder.
3 Select desired file to be played back by pressing the
or button.
4 Press the / (CD/USB / ) button. Playback will start
and the file name will be displayed.
l Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
l Display content can be changed by pressing the
DISPLAY button.
n To remove USB memory device
1
Press the (CD/USB ) button to stop playback.
2 Disconnect USB memory device from the USB terminal.
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-17
Listening to the radio
Notes:
l When radio interference occurs, auto scan tuning may
stop automatically at that point.
l Auto scan tuning will skip weak signal stations.
l To stop the auto tuning, press the TUNING (
or
)
button again.
l When an RDS (Radio Data System) station is tuned in,
the frequency will be displayed first, and then the RDS
indicator will light up. Finally, the station name will
appear.
l Full auto tuning can be achieved for RDS stations
“ASPM”, see page 18.
To receive an FM stereo transmission:
l Press the TUNER (BAND) button to select stereo mode
and “ST” indicator will be displayed. “ ” and “ ” will
appear when an FM broadcast is in stereo.
l If the FM reception is weak, press the TUNER (BAND)
button to extinguish the “ST” indicator. The reception
changes to monaural, and the sound becomes clearer.
You can store 40 AM and FM stations in memory and recall
them at the push of a button. (Preset tuning)
Note:
The backup function protects the memorised stations for a
few hours should there be a power failure or the AC power
lead become disconnected.
1 Press the PRESET
(
or
)
button for less than 0.5
seconds to select the desired station.
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
n Tuning
1
Press the STANDBY/ON button to turn the power on.
2 Press the TUNER (BAND) button repeatedly to select
the desired frequency band (FM or AM).
3 Press the TUNING (
or
) button on the remote
control to tune in to the desired station.
l Manual tuning:
Press the TUNING (
or
) button repeatedly to
tune in to the desired station.
l Auto tuning:
When the TUNING (
or
) button is pressed for
more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
STANDBY/ON
INPUT
PHONES AUDIO IN
TIMER
VOLUME
USB
X-HM50
STANDBY/ON
INPUT
n Memorising a station
1
Perform steps 1 - 3 in “Tuning”.
2 Press the MEMORY button.
3 Within 30 seconds, press the PRESET
(
or
)
button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
4 Within 30 seconds, press the MEMORY button to store
that station in memory. If the “MEMORY” and preset
number indicators disappear before the station is
memorised, repeat the operation from step 2.
5 Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
n To recall a memorised station
n To scan the preset stations
1
Press the PRESET
(
or
)
button for more than 0.5
seconds. The preset number will flash and the
programmed stations will be tuned in sequentially, for 5
seconds each.
2 Press the PRESET
(
or
)
button again when the
desired station is located.
n To erase entire preset memory
1
Press the STANDBY/ON button to enter the stand-by
mode.
2 Whilst pressing down the button, press the
STANDBY/ON button until “Tuner Clear” appears.
STANDBY/ON
11/2/23 X-HM50_En.fm
En-18
Using the Radio Data System (RDS)
RDS is a broadcasting service which a growing
number of FM stations provide. These FM stations
send additional signals along with their regular
programme signals. They send their station names,
and information about the type of programme such as
sport, music, etc.
When tuned to an RDS station, “RDS” and the station
name will be displayed.
“TP” (Traffic Programme) will appear on the display when
the received broadcast carries traffic information, and “TA”
(Traffic Announcement) will appear whilst a traffic
information is on air.
“PTYI” (Dynamic PTY Indicator) will appear whilst the
Dynamic PTY station is received.
You can control the RDS by using the buttons on the
remote control only.
Each time the RDS DISPLAY button is pressed, the
display will switch as follows:
Whilst in the ASPM operation mode, the tuner will
automatically search for new RDS stations. Up to 40
stations can be stored.
If you have already stored some stations in memory, the
number of new stations you can store will be less.
To stop the ASPM operation before it is complete:
Press the RDS ASPM button whilst it is scanning for
stations.
The stations which are already stored in memory will be
kept there.
Notes:
l If the same station is broadcasting on different
frequencies, the strongest frequency will be stored in
memory.
l Any station which has the same frequency as the one
stored in memory will not be stored.
l If 40 stations have already been stored in memory, the
scan will be aborted. If you want to redo the ASPM
operation, erase the preset memory.
l If no station have been stored in memory, “END” will
appear for about 4 seconds.
l If the RDS signals are very weak, station names may
not be stored in memory.
l The same station name can be stored in different
channels.
l In a certain area or during certain time periods, the
station names may temporarily be different.
n Information provided by RDS
When tuning in to a station other than an RDS station or
to an RDS station which sends weak signal, the display
will change in the following order:
Station name (PS) Programme type (PTY)
Frequency Radio text (RT)
No PS No PTY
FM 98.80 MHz
No RT
n Using the Auto Station Programme
Memory (ASPM)
1
Press the TUNER (BAND) button on the remote
control or INPUT button repeatedly on the main unit to
select TUNER function.
2 Press and hold down the RDS ASPM button on the
remote control.
1 After “ASPM” has flashed for about 4 seconds,
scanning will start (87.50 - 108.00 MHz).
2 When an RDS station is found, “RDS” will appear
for a short time and the station will be stored in
memory.
3 After scanning, the number of stations stored in
memory will be displayed for 4 seconds, and then
“END” will appear for 4 seconds.
11/2/23 X-HM50_En.fm
9
8
7
6
5
4
3
2
1
En-19
Using the Radio Data System (RDS) (continued)
If any of the following events occur, it does not mean
that the unit is faulty:
l “PS”, “No PS” and a station name appear alternately,
and the unit does not operate properly.
l If a particular station is not broadcasting properly or a
station is conducting tests, the RDS reception function
may not work properly.
l When you receive an RDS station whose signal is too
weak, information like the station name may not be
displayed.
l “No PS”, “No PTY” or “No RT” will flash for about 5
seconds, and then the frequency will be displayed.
Notes for radio text:
l The first 14 characters of the radio text will appear for
4 seconds and then they will scroll across the display.
l If you tune in to an RDS station which is not
broadcasting any radio text, “No RT” will be displayed
when you switch to the radio text position.
l Whilst radio text data is received or when the text
contents change, “RT” will be displayed.
To specify programmed types and select stations
(PTY search):
You can search a station by specifying the programme type
(news, sports, traffic programme, etc. ... see page 20) from
the stations in memory.
Notes:
l If the display has stopped flashing, start again from
step 2. If the unit finds a desired programme type, the
corresponding channel number will lit for about
8 seconds, and then the station name will remain it.
l If you want to listen to the same programme type of
another station, press the RDS PTY button whilst the
channel number or station name is flashing. The unit
will look for the next station.
l If no station can be found, “NOT FOUND” will appear
for 4 seconds.
If you select the traffic programme:
If you select the traffic programme (TP) in step 3, “TP” will
appear.
(This does not mean that you can listen to the traffic
information at that time.)
When the traffic information is broadcast, “TA” will appear.
n Notes for RDS operation n To recall stations in memory
1
Press the TUNER (BAND) button on the remote control
or INPUT button repeatedly on the main unit to select
TUNER function.
2 Press the RDS PTY button on the remote control.
“SELECT” and “PTY TI” will appear alternately for
about 6 seconds.
3 Within 6 seconds, press the or button to select
the programme type.
Each time the button is pressed, the programme type
will appear. If the button is held down for more than
0.5 seconds, the programme type will appear
continuously.
4 Whilst the selected programme type is flashing (within
6 seconds), press the RDS PTY button again.
After the selected programme type has been lit for 2
seconds, “SEARCH” will appear, and the search
operation will start.
11/2/23 X-HM50_En.fm
En-20
Using the Radio Data System (RDS) (continued)
Descriptions of the PTY (Programme Type) codes, TP
(Traffic Programme) and TA (Traffic Announcement)
You can search for and receive the following PTY, TP and
TA signals.
NEWS Short accounts of facts, events and
publicly expressed views, reportage and
actuality.
AFFAIRS Topical programme expanding or
enlarging upon the news, generally in
different presentation style or concept,
including debate, or analysis.
INFO Programmes whose purpose is to impart
advice in the widest sense.
SPORT Programme concerned with any aspect
of sport.
EDUCATE Programme intended primarily to
educate, of which the formal element is
fundamental.
DRAMA All radio plays and serials.
CULTURE Programmes concerned with any aspect
of national or regional culture, including
language, theatre, etc.
SCIENCE Programmes about the natural sciences
and technology.
VARIED Used for mainly speech-based
programmes usually of light-
entertainment nature, not covered by
other categories. Examples include:
quizzes, panel games, personality
interviews.
POP M Commercial music, which would
generally be considered to be of current
popular appeal, often featuring in current
or recent record sales charts.
ROCK M Contemporary modern music, usually
written and performed by young
musicians.
EASY M Current contemporary music considered
to be “easy-listening”, as opposed to
Pop, Rock or Classical, or one of the
specialised music styles, Jazz, Folk or
Country. Music in this category is often
but not always, vocal, and usually of
short duration.
LIGHT M Classical music for general, rather than
specialist appreciation. Examples of
music in this category are instrumental
music, and vocal or choral works.
CLASSICS Performances of major orchestral works,
symphonies, chamber music, etc., and
including Grand Opera.
OTHER M Musical styles not fitting into any of the
other categories. Particularly used for
specialist music of which Rhythm &
Blues and Reggae are examples.
WEATHER Weather reports and forecasts and
meteorological information.
FINANCE Stock Market reports, commerce,
trading, etc.
CHILDREN For programmes targeted at a young
audience, primarily for entertainment
and interest, rather than where the
objective is to educate.
SOCIAL Programmes about people and things
that influence them individually or in
groups. Includes: sociology, history,
geography, psychology and society.
RELIGION Any aspect of beliefs and faiths, involving
a God or Gods, the nature of existence
and ethics.
PHONE IN Involving members of the public
expressing their views either by phone or
at a public forum.
TRAVEL Features and programmes concerned
with travel to near and far destinations,
package tours and travel ideas and
opportunities. Not for use for
announcements about problems, delays,
or roadworks affecting immediate travel
where TP/TA should be used.
LEISURE Programmes concerned with
recreational activities in which the
listener might participate. Examples
include, Gardening, Fishing, Antique
collecting, Cooking, Food & Wine, etc.
JAZZ Polyphonic, syncopated music
characterised by improvisation.
COUNTRY Songs which originate from, or continue
the musical tradition of the American
Southern States. Characterised by a
straightforward melody and narrative
story line.
NATION M Current Popular Music of the Nation or
Region in that country's language, as
opposed to International “Pop” which is
usually US or UK inspired and in English.
OLDIES Music from the so-called “golden age” of
popular music.
FOLK M Music which has its roots in the musical
culture of a particular nation, usually
played on acoustic instruments. The
narrative or story may be based on
historical events or people.
DOCUMENT Programme concerned with factual
matters, presented in an investigative
style.
TEST Broadcast when testing emergency
broadcast equipment or receivers.
ALARM Emergency announcement made under
exceptional circumstances to give
warning of events causing danger of a
general nature.
NONE No programme type (receive only).
TP Broadcasts which carry traffic
announcements.
TA Traffic announcements are being
broadcast.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Pioneer X-HM50-S Le manuel du propriétaire

Catégorie
Lecteur CD
Taper
Le manuel du propriétaire
Ce manuel convient également à