Pioneer X-HM50K-K Le manuel du propriétaire

Marque: Pioneer

Modèle: X-HM50K-K

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

Ce manuel convient également à

11/2/23 X-HM50_Cover.fm

X-HM50-K/-S

CD Receiver System

Système récepteur CD

Sistema receptor de CD

Operating Instructions

Mode d’emploi

Manual de instrucciones

Discover the benefits of registering your product online at

http://www.pioneer.co.uk (or http://www.pioneer.eu).

Découvrez les nombreux avantages offerts en enregistrant votre produit en

ligne maintenant sur

http://www.pioneer.fr (ou http://www.pioneer.eu).

Registre su producto en

http://www.pioneer.es (o en

http://www.pioneer.eu) Descubra los beneficios de registrarse on-line:

11/2/23 X-HM50_Anki_En.fm

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 10 cm at top, 10 cm at rear, and 10 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

10 cm 10 cm

10 cm

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

11/2/23 X-HM50_Anki_En.fm

E-3

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Condensation

If the player is moved suddenly from a cold place into a

warm room (in winter, for example) or if the

temperature in the room in which the player is installed

rises suddenly due to a heater, etc., water droplets

(condensation) may form inside (on operating parts and

the lens). When condensation is present, the player will

not operate properly and playback is not possible. Let

the player stand at room temperature for 1 or 2 hours

with the power turned on (the time depends on the

extent of condensation). The water droplets will

dissipate and playback will become possible.

Condensation can also occur in the summer if the

player is exposed to the direct wind from an

air-conditioner. If this happens, move the player to a

different place.

S005_A1_En

“Made for iPod” and “Made for iPhone” mean that an

electronic accessor y has been designed to connect

specifically to iPod, or iPhone, respectively, and has

been certified by the developer to meet Apple

performance standards. Apple is not responsible for

the operation of this device or its compliance with

safety and regulator y

standards.

iPod and iPhone are a trademarks of Apple Inc.,

registered in the U.S. and other countries.

CAUTION

This product is a class 1 laser product classified

under the Safety of laser products, IEC 60825-1:2007,

but this product contains a laser diode higher than

Class 1. To ensure continued safety, do not remove

any covers or attempt to gain access to the inside of

the product.

Refer all servicing to qualified personnel.

The

following caution label appears on your unit.

Location: Inside of the unit

D58-5-2-2b*_A1_En

CLASS 1 LASER PRODUCT

Laser Diode Properties

Material: AIGaAs

Wavelength: 790 nm

Emission Duration: continuous

Laser Output: max. 0.7 mW

11/2/23 X-HM50_En.fm

En-4

l X-HM50 CD Receiver System consisting of main unit and speaker system.

Introduction

Thank you for purchasing this PIONEER product. To obtain the best performance from this product, please read this

manual carefully. It will guide you in operating your PIONEER product.

Special Note

Supply of this product does not convey a license nor imply any right to distribute content created with this product in

revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue-generating

streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution

systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact

discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for

such use is required. For details, please visit http://mp3licensing.com

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

Accessories

Please confirm that the following accessories are included.

Page

General Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . 5 - 6

Preparation for Use

System connections . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 8

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Basic Operation

General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting the clock (Remote control only) . . . . . . . . . . 9 - 10

iPod and iPhone

Listening to the iPod or iPhone . . . . . . . . . . . . . . . 10 - 11

CD or MP3/WMA disc Playback

Listening to a CD or MP3/WMA disc . . . . . . . . . . . . . . 12

Advanced CD or MP3/WMA disc playback . . . . . . 13 - 14

MP3/WMA folder mode

(only for MP3/WMA files) . . . . . . . . . . . . . . . . . . . . 14 - 15

Page

USB

Listening to USB mass storage

device/MP3 player . . . . . . . . . . . . . . . . . . . . . . . . .15 - 16

Advanced USB playback . . . . . . . . . . . . . . . . . . . . . . . 16

Radio

Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Advanced Features

Using the Radio Data System (RDS) . . . . . . . . . . 18- 20

Timer and sleep operation

(Remote control only) . . . . . . . . . . . . . . . . . . . . . 21 - 22

Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . 23

References

Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . .23 - 24

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

iPhone adaptors x 3 Remote control x 1 “AAA” size battery

(UM/SUM-4, R3, HP-16

or similar) x 2

AM loop aerial x 1

Warranty card

These operating instructions

FM aerial x 1 Speaker wires x 2

CONTENTS

ENGLISH

11/2/23 X-HM50_En.fm

En-5

Precautions

l Use the unit on a firm, level surface free from vibration.

l Place the speakers at least 30 cm away from any CRT

TV to avoid colour variations across the TV screen. If

the variations persist, move the speakers further away

from the TV. LCD TV is not prone to such variation.

l Keep the unit away from direct sunlight, strong

magnetic fields, excessive dust, humidity and

electronic/electrical equipment (home computers,

facsimiles, etc.) which generate electrical noise.

l Do not place anything on top of the unit.

l Do not expose the unit to moisture, to temperatures

higher than 60°C (140°F) or to extremely low

temperatures.

l If your system does not work properly, disconnect the

AC power lead from the wall socket. Plug the AC power

lead back in, and then turn on your system.

l In case of an electrical storm, unplug the unit for safety.

l Hold the AC power plug by the head when removing it

from the wall socket, as pulling the lead can damage

internal wires.

l The AC power plug is used as a disconnect device and

shall always remain readily operable.

l Do not remove the outer cover, as this may result in

electric shock. Refer internal service to your local

PIONEER service facility.

l The ventilation should not be impeded by covering the

ventilation openings with items, such as newspapers,

tablecloths, curtains, etc.

l No naked flame sources, such as lighted candles,

should be placed on the apparatus.

l Attention should be drawn to the environmental aspects

of battery disposal.

l The apparatus is designed for use in moderate

climates.

Warning:

The voltage used must be the same as that specified on

this unit. Using this product with a higher voltage other

than that which is specified is dangerous and may result in

a fire or other type of accident causing damage. PIONEER

will not be held responsible for any damage resulting from

use of this unit with a voltage other than that which is

specified.

The sound level at a given volume setting depends on

speaker efficiency, location, and various other factors. It is

advisable to avoid exposure to high volume levels. Do not

turn the volume on to full at switch on. Listen to music at

moderate levels. Excessive sound pressure from

earphones and headphones can cause hearing loss.

Controls and indicators

Page

1. Remote sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2. Timer indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3. Disc Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4. iPod or iPhone Docking Station . . . . . . . . . . . . . 10

5. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6. STANDBY/ON Button. . . . . . . . . . . . . . 9, 11, 12, 17

7. INPUT Button . . . . . . . . . . . . . . . . . . . 11, 12, 15, 17

8. Headphone Socket . . . . . . . . . . . . . . . . . . . . . . . 23

9. Audio In Socket . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Page

10. USB Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

11. Tuner Preset Down, CD/USB Track Down,

iPod/iPhone Skip Down . . . . . . . . . . . . . . . . . 11, 12

12. Tuner Preset Up, CD/USB Track Up,

iPod/iPhone Skip Up . . . . . . . . . . . . . . . . . . . 11, 12

13. Disc/USB Stop Button . . . . . . . . . . . . . . . . . . . . . 12

14. Disc/USB/iPod/iPhone Play or

Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . 11, 12

15. Disc Tray Open/Close Button . . . . . . . . . . . . . . . 12

n General

n Volume control

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

8 10 11 12 13 14 15

52 3

n Front panel

11/2/23 X-HM50_En.fm

En-6

Controls and indicators (continued)

Page

1. Remote Control Transmitter . . . . . . . . . . . . . . . . . 8

2. STANDBY/ON Button . . . . . . . . . . . . . . 9, 11, 12, 21

3. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . 17, 18

4. RDS ASPM Button . . . . . . . . . . . . . . . . . . . . . . . . 18

5. Mute Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6. Direct Search Buttons . . . . . . . . . . . . . . . . . . . . . 13

7. iPod/iPhone DISPLAY TV OUT Button . . . . . . . . 11

8. Disc/USB Display Button. . . . . . . . . . . . . . . . . . . 15

9. Tuning Down, Skip Down, Fast Reverse,

Time Down Button . . . . . . . . . . 9, 11, 12, 15, 17, 21

10. Tuner Preset Up Button,

iPod Cursor Up. . . . . . . . . . . . . . . . . . . . . 11, 15, 17

11. Volume Down Button . . . . . . . . . . . . . . . . . . . . . . . 9

12. Tuner Preset Down Button,

iPod Cursor Down . . . . . . . . . . . . . . . . . . 11, 15, 17

13. Equalizer Mode Button . . . . . . . . . . . . . . . . . . . . . 9

14. iPod/iPhone Button . . . . . . . . . . . . . . . . . . . . . . . 11

15. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

16. Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . 12

17. RDS Display Button . . . . . . . . . . . . . . . . . . . . . . 18

18. RDS PTY Button. . . . . . . . . . . . . . . . . . . . . . . . . . 18

19. EXTRA BASS Button . . . . . . . . . . . . . . . . . . . . . . . 9

20. Bass/Treble Button . . . . . . . . . . . . . . . . . . . . . . . . 9

21. Memory Button. . . . . . . . . . . . . . . . . . . . . . . . 13, 17

22. Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

23. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . 9, 21

24. Sleep Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

25. Folder Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

26. Play Mode Button. . . . . . . . . . . . . . . . . . . . . . . . . 13

27. iPod/iPhone Play/Pause Button . . . . . . . . . . . . . 11

28. iPod/iPhone Menu Button . . . . . . . . . . . . . . . . . . 11

29. Disc/USB Play/Pause Button . . . . . . . . . 12, 13, 15

30. Disc/USB Stop Button . . . . . . . . . . . . . . 12, 15, 16

31. Tuning Up, Skip Up, Fast Forward,

Time Up Button . . . . . . . . . . . . 9, 11, 12, 15, 17, 21

32. Volume Up Button . . . . . . . . . . . . . . . . . . . . . . . . . 9

33. Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 21

34. Dimmer Button . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 9

35. Audio/Line (INPUT) Button . . . . . . . . . . . . . . . 8, 23

36. USB Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Page

1. USB Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2. iPod Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3. CD Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4. MP3 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5. WMA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6. RDM (Random) Indicator. . . . . . . . . . . . . . . . . . . 13

7. MEM (Memory) Indicator . . . . . . . . . . . . . . . . . . . 13

8. Repeat Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . 13

9. Play/Pause Indicator . . . . . . . . . . . . . . . . . . . . . . 12

10. Tuning FM/AM Indicator . . . . . . . . . . . . . . . . . . . 17

11. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . 17

12. Stereo Station Indicator . . . . . . . . . . . . . . . . . . . 17

13. RDS Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

14. PTY Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

15. TP Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

16. TA Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

17. Muting Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

18. Title Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

19. Artist Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

20. Folder Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 15

21. Album Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 15

22. File Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

23. Track Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

24. Daily Timer Indicator . . . . . . . . . . . . . . . . . . . . . . 21

25. Once Timer Indicator . . . . . . . . . . . . . . . . . . . . . . 21

26. Disc Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

27. Total Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

28. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

n Speaker system

1. Dome-Tweeter

2. Woofer

3. Bass Reflex Duct

4. Speaker Terminal

n Speaker grilles are removable

Make sure nothing comes into contact

with the speaker diaphragms when

you remove the speaker grilles.

1 4 5 6 7

10 11 1312 14

28272624 2523221918 2120

2 3

n Remote control

n Display

11/2/23 X-HM50_En.fm

En-7

System connections

Supplied FM aerial:

Connect the FM aerial wire to the FM 75 ohms socket and

position the FM aerial wire in the direction where the

strongest signal can be received.

External FM aerial:

Use an external FM aerial (75 ohms coaxial cable) for

better reception. When an external FM aerial is used,

disconnect the supplied FM aerial wire.

Supplied AM loop aerial:

Connect the AM loop aerial to the AM terminal. Position

the AM loop aerial for optimum reception. Place the AM

loop aerial on a shelf, etc., or attach it to a stand or a wall

with screws (not supplied).

Note:

Placing the aerial on the unit or near the AC power lead

may cause noise pickup. Place the aerial away from the

unit for better reception.

Photo and video files from iPod or iPhone can be viewed

by connecting the system to TV/monitor.

If the TV/monitor has a video input, connect it to the VIDEO

OUT socket at the back of the unit and set the TV Out on

the iPod or iPhone unit to “ON” position.

Note:

Please make sure to set iPod unit to either NTSC or PAL to

match your TV signal. Please visit Apple’s homepage for

further information.

After checking all the connections have been made

correctly, plug the AC power lead of this unit into the wall

socket.

Note:

Unplug the AC power lead from the wall socket if the unit

will not be in use for a prolonged period of time.

CAUTION

Handle the power cord by the plug part. Do not pull out the

plug by tugging the cord, and never touch the power cord

when your hands are wet, as this could cause a short

circuit or electric shock. Do not place the unit, a piece of

furniture, or other object on the power cord or pinch the

cord in any other way. Never make a knot in the cord or tie

it with other cables. The power cords should be routed so

that they are not likely to be stepped on. A damaged power

cord can cause a fire or give you an electric shock. Check

the power cord once in a while. If you find it damaged, ask

your nearest Pioneer authorized independent service

company for a replacement.

Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

Right

speaker

FM aerial

To video input socket

screws (not supplied)

wall

< Attaching

to the wall >

< Assembling >

Wall socket

(AC 220 V to 230 V,

50 Hz/60 Hz)

Installing the AM loop aerial

Video cable

(not supplied)

AM loop

aerial

Left

speaker

n Aerial connection

n Speaker connection

Twist exposed wire strands together.

l Connect the red wire to the plus

(+) terminal, and other wire to the

minus (–) terminal.

l Use speakers with an impedance

of 4 ohms - 16 ohms, as lower

impedance speakers can damage

the unit.

These speaker terminals carry HAZARDOUS LIVE voltage.

To prevent the risk of electric shock when connecting or

disconnecting the speaker cables, disconnect the power

cord before touching any uninsulated parts.

l Do not attach these speakers to the wall or ceiling, as

they may cause injury in the event of a fall.

Do not mistake the right and the left channels. The right

speaker is the one on the right side when you face the unit.

l Do not let the bare speaker wires touch each other.

l Do not allow any objects to fall into or to be placed in

the bass reflex ducts.

Do not stand or sit on the speakers. You may be injured.

Do not connect the supplied speakers with any other

amplifier. This may result in malfunction or fire.

Incorrect

n Connecting iPod or iPhone to TV

n AC power connection

11/2/23 X-HM50_En.fm

En-8

System connections (continued)

You can connect a subwoofer with an amplifier to the

SUBWOOFER PRE OUT socket.

Notes:

No sound is heard from the subwoofer without a built-in

amplifier.

Subwoofer Pre-out (audio signal): 350 mV / 10 k ohms at

70 Hz.

Connect to the TV using an audio cable

To select Line In function:

On main unit: Press INPUT button repeatedly until

Line In is displayed.

On remote control: Press AUDIO/LINE (INPUT) button

repeatedly until Line In is displayed.

Remote control

WARNNIG:

l Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a

heater. This can cause batteries to leak, overheat,

explode or catch fire. It can also reduce the life or

performance of batteries.

Caution:

l When inserting the batteries, make sure not to damage

the springs on the battery’s (

–

) terminals.

Replace all old batteries with new ones at the same time.

Do not mix old and new batteries.

Remove the batteries if the unit will not be used for a long

period of time. This will prevent potential damage due to

battery leakage.

Do not use rechargeable batteries (nickel-cadmium

battery, etc.).

Installing the batteries incorrectly may cause the unit to

malfunction.

Notes concerning use:

Replace the batteries if the operating distance is reduced

or if the operation becomes erratic. Purchase 2 “AAA” size

batteries (UM/SUM-4, R3, HP-16 or similar).

Periodically clean the transmitter on the remote control

and the sensor on the unit with a soft cloth.

Exposing the sensor on the unit to strong light may

interfere with operation. Change the lighting or the

direction of the unit if this occurs.

Keep the remote control away from moisture, heat, shock,

and vibrations.

l When disposing of used batteries, please comply with

governmental regulations or environmental public

instruction's rules that apply in your country or area.

Check the remote control after checking all the connections.

Point the remote control directly at the remote sensor on the

unit. The remote control can be used within the range shown

below:

n Using other subwoofer

n Connecting a TV, etc.

Audio cable

(commercially

available)

Audio signal

To audio input

socket

To SUBWOOFER PRE

OUT socket

Main unit

Commercially available subwoofer

(amplifier built in)

Audio signal

To audio

output sockets

Audio cable

(commercially

available)

Main unit

To L INE

input

sockets

n Battery installation

Open the battery cover.

Insert the supplied batteries according to the direction

indicated in the battery compartment.

When inserting or removing the batteries, push them

towards the (–) battery terminals.

Close the cover.

n Test of the remote control

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

7 m

Remote sensor

11/2/23 X-HM50_En.fm

En-9

General control

Press the STANDBY/ON button to turn the power on.

To dim the display brightness, press the DIMMER button on the

remote control.

If you turn off and on the main unit with the volume set to 27 or higher,

the volume starts at 16 and fades in to the last set level.

Turn the volume knob towards VOLUME (on main unit) or press VOL

+/– (on remote control) to increase or decrease the volume.

When you press any of the following buttons, the unit turns on.

iPod / iPhone, CD, USB, AUDIO / LINE (INPUT), TUNER (BAND)

on the remote control: Selected function is activated.

/ button on the main unit: The unit turns on and playback of

the last function will start (CD, TUNER, USB, iPod, AUDIO IN,

LINE IN)

The main unit will enter the stand-by mode (when iPod/iPhone is not

docked) after 15 minutes of inactivity during:

iPod/iPhone: No connection or in the pause mode.

CD / USB: In the stop mode.

The volume is muted temporarily when pressing the MUTE button on

the remote control. Press again to restore the volume.

When the power is first turned on, the unit will enter the extra bass

mode which emphasises the bass frequencies. To cancel the extra

bass mode, press the EXTRA BASS button on the remote control.

Press the BASS/TREBLE button to select “Bass”.

Within 5 seconds, press the VOL (+ or –) button to adjust the bass.

Press the BASS/TREBLE button to select “Treble”.

Within 5 seconds, press the VOL (+ or –) button to adjust the

treble.

When the INPUT button on main unit is pressed, the current function

will change to different mode. Press the INPUT button repeatedly to

select desired function.

Note:

The backup function will protect the memorised function mode for a

few hours should there be a power failure or the AC power lead

becomes disconnected.

Setting the clock (

Remote

control only)

In this example, the clock is set for the 24-hour (00:00) display.

n To turn the power on

After use:

Press the STANDBY/ON button to enter the power stand-by mode.

Note:

However, if iPod/iPhone is docked, the unit will begin charging.

“iPod charge” will be displayed.

n Display brightness control

n Volume auto fade-in

n Volume control

n Auto power on function

n Auto power off function

n Muting

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

INPUT

Dimmer 1

Dimmer 2

Dimmer off

(Display is dim).

(Display gets dimmer).

(Display is bright).

n Extra-Bass control

n Bass control

n Treble control

n Equaliser

n Function

Press the STANDBY/ON button to turn the power on.

Press the CLOCK/TIMER button.

Within 10 seconds, press the ENTER button. To adjust the day,

press the or button and then press the ENTER button.

Press the or button to select 24-hour or 12-hour display

and then press the ENTER button.

The 24-hour display will appear.

(00:00 - 23:59)

The 12-hour display will appear.

(AM 12:00 - PM 11:59)

The 12-hour display will appear.

(AM 00:00 - PM 11:59)

Pops

Vocal

Jazz

Flat

Game

Classic

For rock music.

For pop music.

No equalization.

For classical music.

For jazz.

Vocals are enhanced.

Equaliser off.

For game.

For classical music.

For pop music.

Vocals are enhanced.

For jazz.

When the EQUALIZER MODE

button is pressed, the current

mode setting will be displayed.

To change to a different mode,

press the EQUALIZER MODE

button repeatedly until the

desired sound mode appears.

FM STEREO

FM MONO

USB

iPod

Audio In

Line In

CD AM

11/2/23 X-HM50_En.fm

En-10

Setting the clock (Remote control

only) (continued)

To confirm the time display:

Press the CLOCK/TIMER button. The time display will appear

for about 5 seconds.

Note:

When power supply is restored after unit is plugged in again

or after a power failure, reset the clock (pages 9 - 10).

To readjust the clock:

Perform “Setting the clock” from step 1. If the “Clock” does not

appear in step 2, step 4 (for selecting the 24-hour or 12-hour

display) will be skipped.

To change the 24-hour or 12-hour display:

Listening to the iPod or iPhone

Supported iPod and iPhone models:

iPod touch (1

generation)

iPod classic

iPod nano (2

generation)

iPhone 4

iPhone 3GS

iPhone 3G

iPhone

Notes:

l Audio from the iPod/iPhone cannot be heard via the

headphones connected to the unit.

Once the iPod or iPhone is connected to the unit it will

begin charging.

Error message “This accessory is not made to work with

iPhone” may appear on the iPhone screen when iPhone

battery is low.

The message “This accessory is not made to work with

iPhone” or “This accessory is not supported by iPhone”

may appear on the iPhone screen when the iPhone is not

properly docked (eg. slanting) on this product. If this

occurs, please remove and re-dock the iPhone.

To prevent random interference when iPod/iPhone

function is selected, the headphone output is

disabled.

You may also experience brief audio interference

during incoming calls.

Notes:

Please use the adaptor supplied with your iPod or iPhone

unit.

You can use an audio cable to connect your iPod to the

AUDIO IN socket if:

your iPod adaptor does not fit into the iPod dock on the

main unit.

you have an iPod that does not have an iPod adaptor.

you have an iPod that does not have an iPod 30 pin

connector.

Caution:

Unplug all accessories from the iPod or iPhone before

inserting it into the dock.

To adjust the hour, press the or button and then

press the ENTER button. Press the or button

once to advance the time by 1 hour. Hold it down to

advance continuously.

To adjust the minutes, press the or button and

then press the ENTER button. Press the or

button once to advance the time by 1 minute.

1 Clear all the programmed contents. [Refer to “Factory

reset, clearing all memory” on page 24 for details.]

2 Perform “Setting the clock” from step 1 onwards.

n iPod and iPhone adaptor connection

iPhone

Adaptor No.

iPhone

Description

Capacity

12 iPhone 4GB & 8GB & 16GB

15 iPhone 3G,

iPhone 3GS

8GB & 16GB & 32GB

& 64GB

19 iPhone 4 16GB & 32GB

n To insert iPod or iPhone adaptor

Open the iPod cover by pulling up.

2 Insert the iPod or iPhone adaptor into unit and connect

your iPod or iPhone.

n To remove iPod or iPhone adaptor

Insert the tip of a screwdriver (“–” type,

small) into the adaptor hole as shown

and lift upward to remove.

n iPod or iPhone playback

Press the STANDBY/ON button to turn the power on.

Press the iPod/iPhone button on the remote control or INPUT

button repeatedly on the main unit to select iPod function.

Insert iPod or iPhone unit in iPod dock of main unit.

Press the / (iPod/iPhone / ) button to start playback.

iPhone

Dock connector

iPhone (bottom)

iPhone dock

iPhone connector

iPhone adaptor

11/2/23 X-HM50_En.fm

En-11

Listening to the iPod or iPhone (continued)

Sound will only switch from iPhone to the main unit after

authentication process is completed in approximately 10

seconds.

Incoming calls will pause the playback and iPhone ringtones

will be heard from the main unit speakers only.

Once the calls are answered, the conversation can only be

heard through the built-in iPhone speaker. Turn on the

iPhone speaker or undock the iPhone to start conversation.

Simply remove the iPod or iPhone from the iPod dock. It is safe

to do so even during playback.

Note:

When navigating the iPod or iPhone menu with remote control, do

not operate any of the buttons on the iPod or iPhone unit. The

volume level is adjusted by pressing the VOL (+ or –) button on

the main unit or the remote control. Adjusting the volume on the

iPod and iPhone units give no effect.

iPod and iPhone operations:

The operations described below depend on the generation iPod

and iPhone you are using.

System on operation:

When the main unit is powered on, the iPod and iPhone units will

automatically power on when docked in the unit.

System off (stand-by operation):

When the main unit is turned to stand-by mode, the docked iPod

and iPhone unit will automatically turn to stand-by mode.

Notes:

If the TV Out setting is already turned on at video menu, the

video is automatically displayed on the TV screen when

ENTER key is pressed.

To return to watching video on iPod or iPhone screen, press

the MENU button to enter video menu. Then press the

DISPLAY TV OUT button for more than 2 seconds until “iPod

Display” appears.

During iPod or iPhone video playback, pressing the DISPLAY

TV OUT button will not toggle video out display between iPod

and TV.

Caution:

Unplug all accessories for the iPod or iPhone before inserting

it into the iPod dock.

n iPhone playback

n To disconnect iPod or iPhone

n Navigating the iPod and iPhone menus

Press the MENU button to view the menu on iPod or iPhone

unit. Press it again to go back to previous menu.

Use the PRESET (

) button to select an item on the

menu and then press ENTER button.

STANDBY/ON

INPUT

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

n Watching videos on a TV connected to

iPod or iPhone

Press the DISPLAY TV OUT button for more than 2 seconds.

“TV Display” will appear on display.

Press the ENTER button to start playback.

n Various iPod functions

Function Main

unit

Remote

control

Operation

Play

Press in the pause

mode.

Pause

Press in the playback

mode.

Track up/

down

Press in the playback or

pause mode.

If you press the button in

the pause mode, press

the / button to start

the desired track.

Fast

forward/

reverse

Press and hold down in

the playback mode.

Release the button to

resume playback.

Display

____

iPod back light ON.

Press for more than 2

seconds to toggle the

video out display

between iPod or TV.

Repeat

____

Press to toggle repeat

mode.

Shuffle

____

Press and hold down to

toggle shuffle mode.

iPod

____

Press to view the iPod

menu during iPod

function.

iPod

Enter

____

Press to confirm the

selection.

iPod

Cursor

Up/Down

____

Press to select the iPod

menu.

11/2/23 X-HM50_En.fm

En-12

Listening to a CD or MP3/WMA disc

This system can play back a standard CD, CD-R/RW in the CD

format and CD-R/RW with MP3 or WMA files, but cannot record

on them. Some audio CD-R and CD-RW discs may not be

playable due to the state of the disc or the device that was used

for recording.

MP3:

MP3 is a form of compression. It is an acronym which stands

for MPEG Audio Layer 3. MP3 is a type of audio code which

is processed by significant compression from the original

audio source with very little loss in sound quality.

This system supports MPEG 1 Layer 3 and VBR files.

During VBR file playback, time counter in the display may

differ from its actual playback time.

Bitrate which is supported by MP3 is 32 kbps to 320 kbps.

WMA:

WMA files are Advanced System Format files that include

audio files which are compressed with Windows Media

Audio codec. WMA is developed by Microsoft as an audio

format file for Windows Media Player.

“MP3” and “WMA” indicator will light up after the unit reads

information on an MP3 or WMA disc.

Bitrate which is supported by WMA is 64 kbps to 160 kbps.

Caution:

Do not place two discs in one disc tray.

Do not play discs of special shapes (heart, octagon, etc). It

may cause malfunctions.

Do not push the disc tray whilst it is moving.

If the power fails whilst the tray is open, wait until the power

is restored.

If TV or radio interference occurs during CD operation, move

the unit away from the TV or radio.

Be sure to place 8 cm disc in the middle of the disc tray.

Due to the structure of the disc information, it takes longer to

read an MP3/WMA disc than a normal CD (approximately 20

to 90 seconds).

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

STANDBY/ON

INPUT

n Disc playback

Press the STANDBY/ON button to turn the power on.

Press the CD button on the remote control or INPUT button

repeatedly on the main unit to select CD function.

Press the button to open the disc tray.

Place the disc on the disc tray, label side up.

Press the button to close the disc tray.

Press the

(CD/USB

) button to start playback. After

the last track is played, the unit will stop automatically.

n Various disc functions

Function Main

unit

Remote

control

Operation

Play

Press in the stop mode.

Stop

Press in the playback

mode.

Pause

Press in the playback

mode. Press the /

button to resume

playback from the

paused point.

Track

up/

down

Press in the playback or

stop mode.

If you press the button in

the stop mode, press the

/ button to start the

desired track.

Fast

forward/

reverse

Press and hold down in

the playback mode.

Release the button to

resume playback.

PHONES

AUDIO IN

USB

11/2/23 X-HM50_En.fm

En-13

Advanced CD or MP3/WMA disc playback

By using the Direct Search buttons, the desired tracks on the

current disc can be played.

Use the Direct Search buttons on the remote control to

select the desired track whilst playing the selected disc.

The Direct Search buttons allow you to select up to

number 9.

When selecting number 10 or higher, use the “>10” button.

Notes:

A track number higher than the number of tracks on the

disc cannot be selected.

During random play, direct search is not possible.

To stop playback:

Press the (CD/USB ) button.

Repeat play can play one track, all tracks or a programmed

sequence continuously.

To repeat one track:

Press the PLAY MODE button repeatedly until “Repeat One”

appears. Press the / (CD/USB / ) button.

To repeat all tracks:

Press the PLAY MODE button repeatedly until “Repeat All”

appears. Press the / (CD/USB / ) button.

To repeat desired tracks:

Perform steps 1 - 5 in “Programmed play” section on this page

and then press the PLAY MODE button repeatedly until

“Repeat All” appears.

To cancel repeat play:

Press the PLAY MODE button repeatedly until “Normal”

appears and “ ” disappears.

The tracks on the disc can be played in random order

automatically.

To random play all tracks:

Whilst in the stop mode, press and hold down PLAY MODE

button on the remote control until “Random” appears. Press the

/ (CD/USB /) button.

To cancel random play:

Press the (CD/USB ) button.

Notes:

If you press the button during random play, you can

move to the track selected next by the random operation.

On the other hand, the button does not allow you to move

to the previous track. The beginning of the track being

played will be located.

In random play, the unit will select and play tracks

automatically. (You cannot select the order of the tracks.)

Caution:

After performing repeat play, be sure to press the (CD/USB

) button. Otherwise, the disc will play continuously.

You can choose up to 32 selections for playback in the order

you like.

n Direct track search

A. For example, to choose 13

Press the “>10” button once.

Press the “1” button.

Press the “3” button.

B. For example, to choose 130

Press the “>10” button twice.

Press the “1” button.

Press the “3” button.

Press the “0” button.

n Repeat play

Selected track number

n Random play

n Programmed play (CD)

Whilst in the stop mode, press the MEMORY button on the

remote control to enter the programming save mode.

Press the or buttons on the remote control to

select the desired track.

Press the MEMORY button to save the track number.

Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be

programmed. If you want to check the programmed tracks,

press the MEMORY button repeatedly. If you make a

mistake, the programmed tracks can be cleared by

pressing the CLEAR button.

Press the / (CD/USB / ) button to start playback.

Selected track number

11/2/23 X-HM50_En.fm

En-14

Advanced CD or MP3/WMA disc

playback (continued)

To cancel the programmed play mode:

Press the (CD/USB ) button. The display will show

“Memory Clear” and all the programmed contents will be

cleared.

Adding tracks to the programme:

If a programme has been previously stored, the “MEM”

indicator will be displayed. Press the MEMORY button

repeatedly to go to the last programme memory. Then

follow steps 2 - 3 to add tracks. The new tracks will be

stored after the last track of the previous programme.

Notes:

l When a disc is ejected, the programme is automatically

cancelled.

l If you press the STANDBY/ON button to enter the

stand-by mode or change the function from CD to

another, the programmed selections will be cleared.

l During the programme operation, random play is not

possible.

MP3/WMA folder mode (only for MP3/

WMA files)

To play back MP3/WMA (Windows Media Audio) file

There are many music sites on the internet that you can

download MP3/WMA (Windows Media Audio) music files.

Follow the instructions from the website on how to

download the music files. You can then play back these

downloaded music files by burning them to a CD-R/RW

disc.

l Your downloaded song/files are for personal use only.

Any other usage of the song without owner’s

permission, is against the law.

If MP3/WMA files are recorded in several folders, a folder

number will be set to each folder automatically.

These folders can be selected by the FOLDER button on

the remote control. If there is no supported file formats

inside the selected folder, the folder is skipped and the next

folder will be selected.

Example: How to set folder number if MP3/WMA format

files are recorded as below figure.

l The folder and file order information which is recorded

on the disc depends on the writing software. There

maybe possibilities that this unit will playback the files

not according to our expected playback order.

l For CD MP3/WMA, 255 numbers of folders and files

inclusive of the folders which have non playable files

can be read.

Folder mode on/off can be operated by the FOLDER

button on the remote control. Files that are played when

folder mode is set to the on position, may differ from those

played back when folder mode is turned off.

n Programmed play (MP3/WMA)

Whilst in the stop mode, press the MEMORY button to

enter the programming save mode.

2 Press the PRESET

(

)

button on the remote

control to select the desired folder.

Then press the or button on the remote control

to select the desired tracks.

3 Press the MEMORY button to save the folder and track

number.

4 Repeat steps 2 - 3 for other folder/tracks. Up to 32

tracks can be programmed.

5 Press the / (CD/USB / ) button to start playback.

n About folder playback order

ROOT folder is set as folder 1.

2 As for folders inside ROOT folder (Folder A and Folder

B), the folder which is recorded earlier on the disc will be

set as folder 2 and folder 3.

3 As for folder inside Folder A (Folder C and Folder D), the

folder which is recorded earlier on the disc will be set as

folder 4 and folder 5.

4 Folder E that is inside Folder D will be set as folder 6.

ROOT

(FOLDER 1)

FOLDER A

(FOLDER 2)

FOLDER B

(FOLDER 3)

FILE 9

FILE 10

FILE 3

FILE 4

FILE 5

FILE 6

FILE 7

FILE 8

FOLDER E

(FOLDER 6)

FOLDER C

(FOLDER 4)

FOLDER D

(FOLDER 5)

FILE 1

FILE 2

11/2/23 X-HM50_En.fm

En-15

MP3/WMA folder mode (only for MP3/

WMA files) (continued)

To play back CD-R/RW.

Note:

If “Not Support” is displayed, it means “Copyright protected

WMA file” or “Not supported playback file” is selected.

Listening to USB mass storage

device/MP3 player

Notes:

l This USB mass storage device or MP3 player is not

compatible with MTP and AAC file systems.

l Some external storage devices may not operate with

this system.

l Operation of external storage devices (USB memory

devices, external hard disks, etc.) is not guaranteed.

Note:

To pause playback:

Press the / (CD/USB / ) button.

n Procedure to playback MP3/WMA disc with

folder mode on

Press the CD button, and load an MP3/WMA disc.

Press the FOLDER button and disc info will be

displayed.

2 Press the PRESET

(

)

button to select desired

playback folder. (Folder mode on)

3 Select desired file to be played back by pressing the

or button.

4 Press the / (CD/USB / ) button. Playback will start

and file name will be displayed.

l Title, Artist and Album name are displayed if they are

recorded on the disc.

l Display content can be changed by pressing the

DISPLAY button.

MP3 indicator

WMA indicator

TOTAL indicator

Total number of files

Total number of folder

First track number

in the folder

FOLDER

indicator

FOLDER number

File name display Folder display

Title display

Album display

Counter display

Artist display

n To play back USB/MP3 player with folder

mode off

Press the USB button on the remote control or INPUT

button repeatedly on main unit to select USB function.

Connect the USB memory device that has MP3/WMA

format files on the unit. When the USB memory is

connected to the main unit, the device information will

be displayed.

2 Select desired file to be played back by pressing the

or button.

3 Press the / (CD/USB / ) button. Playback will start

and the file name will be displayed.

l Title, Artist and Album name are displayed if they are

recorded in the USB memory device.

l Display content can be changed by pressing the

DISPLAY button.

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

INPUT

11/2/23 X-HM50_En.fm

En-16

Listening to USB mass storage device/MP3 player (continued)

Notes:

l PIONEER will not be held liable for the loss of data

whilst the USB memory device is connected to the

audio system.

l Files compressed in MP3 and/or WMA format can be

played back when connected to the USB terminal.

l This USB memory’s format supports FAT 16 or FAT 32.

l PIONEER cannot guarantee that all USB memory

devices will work on this audio system.

l USB cable is not recommended for use in this audio

system to connect to USB memory device. Use of the

USB cable will affect the performance of this audio

system.

l This USB memory cannot be operated via USB hub.

l The USB terminal in this unit is not intended for a PC

connection but is used for music streaming with a USB

memory device.

l External HDD-storage cannot be played back via USB

terminal.

l If the data inside the USB memory is large, it may take

longer time for the data to be read.

l This product can play WMA and MP3 files. It will

automatically detect the file type being played. If

unplayable file is played on this product, “Not Support”

is indicated and the file will be automatically skipped.

This will take a few seconds. If abnormal indications

appear on the display due to the unspecified file, turn

off the unit and then turn it on again.

l This product relates to USB mass storage devices and

MP3 players. It may however face some irregularities

due to various unforeseen reasons from some devices.

Should this happen, turn off the unit and then turn it on

again.

l The USB port is only intended for direct connection to

a USB memory device without any cable.

l During CD function, MP3 player will not be charging.

l “Not support” will be displayed if you connect an iPod to

USB terminal when the USB function is selected.

Advanced USB playback

The following functions are the same as CD

operations:

Page

Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Programmed play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Note:

If USB memory device is not connected, “No USB” will be

shown on the display.

Notes:

l This unit only supports “MPEG-1 Audio Layer-3”

format. (Sampling Frequency is 32 kHz, 44.1 kHz, 48

kHz)

l Playback order for MP3 files may differ depending on

the writing software used during file download.

l Bitrate which is supported by MP3 is 32 kbps to 320

kbps, WMA is 64 kbps to 160 kbps.

l For MP3/WMA files, please put “.MP3” “.WMA”

extension. Files cannot be played back if there is no

MP3/WMA extension.

l Playlists are not supported on this unit.

l This unit can display Folder Name or File Name up to

32 characters.

l Maximum total number of MP3/WMA files is 1024.

Maximum total number of folders is 255 inclusive of

root directory.

l The display playback time may not be displayed

correctly when playing back a variable bitrate file.

l The ID3TAG information supported are TITLE, ARTIST

and ALBUM only. Title name, artist name and album

name can be displayed by pressing the DISPLAY

button during file playback or pause mode.

l WMA meta tag also supports title, artist and album

name which are recorded in WMA files. Copyright

protected WMA files cannot be played back.

n To play back USB/MP3 player with folder

mode on

Press the USB button on the remote control or INPUT

button repeatedly on main unit to select USB function.

Connect the USB memory device that has MP3/WMA

format files on the unit. When the USB memory is

connected to the main unit, the device information will

be displayed.

2 Press the FOLDER button, and press the PRESET

(

)

button to select desired playback folder. To start

playback with folder mode on, go to step 4. To change

the playback folder, press the PRESET

(

)

button

to select another folder.

3 Select desired file to be played back by pressing the

or button.

4 Press the / (CD/USB / ) button. Playback will start

and the file name will be displayed.

l Title, Artist and Album name are displayed if they are

recorded in the USB memory device.

l Display content can be changed by pressing the

DISPLAY button.

n To remove USB memory device

Press the (CD/USB ) button to stop playback.

2 Disconnect USB memory device from the USB terminal.

11/2/23 X-HM50_En.fm

En-17

Listening to the radio

Notes:

l When radio interference occurs, auto scan tuning may

stop automatically at that point.

l Auto scan tuning will skip weak signal stations.

l To stop the auto tuning, press the TUNING (

)

button again.

l When an RDS (Radio Data System) station is tuned in,

the frequency will be displayed first, and then the RDS

indicator will light up. Finally, the station name will

appear.

l Full auto tuning can be achieved for RDS stations

“ASPM”, see page 18.

To receive an FM stereo transmission:

l Press the TUNER (BAND) button to select stereo mode

and “ST” indicator will be displayed. “ ” and “ ” will

appear when an FM broadcast is in stereo.

l If the FM reception is weak, press the TUNER (BAND)

button to extinguish the “ST” indicator. The reception

changes to monaural, and the sound becomes clearer.

You can store 40 AM and FM stations in memory and recall

them at the push of a button. (Preset tuning)

Note:

The backup function protects the memorised stations for a

few hours should there be a power failure or the AC power

lead become disconnected.

1 Press the PRESET

(

)

button for less than 0.5

seconds to select the desired station.

The stations saved in the memory can be scanned

automatically. (Preset memory scan)

n Tuning

Press the STANDBY/ON button to turn the power on.

2 Press the TUNER (BAND) button repeatedly to select

the desired frequency band (FM or AM).

3 Press the TUNING (

) button on the remote

control to tune in to the desired station.

l Manual tuning:

Press the TUNING (

) button repeatedly to

tune in to the desired station.

l Auto tuning:

When the TUNING (

) button is pressed for

more than 0.5 seconds, scanning will start

automatically and the tuner will stop at the first

receivable broadcast station.

STANDBY/ON

INPUT

PHONES AUDIO IN

TIMER

VOLUME

USB

X-HM50

STANDBY/ON

INPUT

n Memorising a station

Perform steps 1 - 3 in “Tuning”.

2 Press the MEMORY button.

3 Within 30 seconds, press the PRESET

(

)

button

to select the preset channel number. Store the stations

in memory, in order, starting with preset channel 1.

4 Within 30 seconds, press the MEMORY button to store

that station in memory. If the “MEMORY” and preset

number indicators disappear before the station is

memorised, repeat the operation from step 2.

5 Repeat steps 1 - 4 to set other stations, or to change a

preset station. When a new station is stored in the

memory, the station previously memorised for that

preset channel number will be erased.

n To recall a memorised station

n To scan the preset stations

Press the PRESET

(

)

button for more than 0.5

seconds. The preset number will flash and the

programmed stations will be tuned in sequentially, for 5

seconds each.

2 Press the PRESET

(

)

button again when the

desired station is located.

n To erase entire preset memory

Press the STANDBY/ON button to enter the stand-by

mode.

2 Whilst pressing down the button, press the

STANDBY/ON button until “Tuner Clear” appears.

STANDBY/ON

11/2/23 X-HM50_En.fm

En-18

Using the Radio Data System (RDS)

RDS is a broadcasting service which a growing

number of FM stations provide. These FM stations

send additional signals along with their regular

programme signals. They send their station names,

and information about the type of programme such as

sport, music, etc.

When tuned to an RDS station, “RDS” and the station

name will be displayed.

“TP” (Traffic Programme) will appear on the display when

the received broadcast carries traffic information, and “TA”

(Traffic Announcement) will appear whilst a traffic

information is on air.

“PTYI” (Dynamic PTY Indicator) will appear whilst the

Dynamic PTY station is received.

You can control the RDS by using the buttons on the

remote control only.

Each time the RDS DISPLAY button is pressed, the

display will switch as follows:

Whilst in the ASPM operation mode, the tuner will

automatically search for new RDS stations. Up to 40

stations can be stored.

If you have already stored some stations in memory, the

number of new stations you can store will be less.

To stop the ASPM operation before it is complete:

Press the RDS ASPM button whilst it is scanning for

stations.

The stations which are already stored in memory will be

kept there.

Notes:

l If the same station is broadcasting on different

frequencies, the strongest frequency will be stored in

memory.

l Any station which has the same frequency as the one

stored in memory will not be stored.

l If 40 stations have already been stored in memory, the

scan will be aborted. If you want to redo the ASPM

operation, erase the preset memory.

l If no station have been stored in memory, “END” will

appear for about 4 seconds.

l If the RDS signals are very weak, station names may

not be stored in memory.

l The same station name can be stored in different

channels.

l In a certain area or during certain time periods, the

station names may temporarily be different.

n Information provided by RDS

When tuning in to a station other than an RDS station or

to an RDS station which sends weak signal, the display

will change in the following order:

Station name (PS) Programme type (PTY)

Frequency Radio text (RT)

No PS No PTY

FM 98.80 MHz

No RT

n Using the Auto Station Programme

Memory (ASPM)

Press the TUNER (BAND) button on the remote

control or INPUT button repeatedly on the main unit to

select TUNER function.

2 Press and hold down the RDS ASPM button on the

remote control.

1 After “ASPM” has flashed for about 4 seconds,

scanning will start (87.50 - 108.00 MHz).

2 When an RDS station is found, “RDS” will appear

for a short time and the station will be stored in

memory.

3 After scanning, the number of stations stored in

memory will be displayed for 4 seconds, and then

“END” will appear for 4 seconds.

11/2/23 X-HM50_En.fm

En-19

Using the Radio Data System (RDS) (continued)

If any of the following events occur, it does not mean

that the unit is faulty:

l “PS”, “No PS” and a station name appear alternately,

and the unit does not operate properly.

l If a particular station is not broadcasting properly or a

station is conducting tests, the RDS reception function

may not work properly.

l When you receive an RDS station whose signal is too

weak, information like the station name may not be

displayed.

l “No PS”, “No PTY” or “No RT” will flash for about 5

seconds, and then the frequency will be displayed.

Notes for radio text:

l The first 14 characters of the radio text will appear for

4 seconds and then they will scroll across the display.

l If you tune in to an RDS station which is not

broadcasting any radio text, “No RT” will be displayed

when you switch to the radio text position.

l Whilst radio text data is received or when the text

contents change, “RT” will be displayed.

To specify programmed types and select stations

(PTY search):

You can search a station by specifying the programme type

(news, sports, traffic programme, etc. ... see page 20) from

the stations in memory.

Notes:

l If the display has stopped flashing, start again from

step 2. If the unit finds a desired programme type, the

corresponding channel number will lit for about

8 seconds, and then the station name will remain it.

l If you want to listen to the same programme type of

another station, press the RDS PTY button whilst the

channel number or station name is flashing. The unit

will look for the next station.

l If no station can be found, “NOT FOUND” will appear

for 4 seconds.

If you select the traffic programme:

If you select the traffic programme (TP) in step 3, “TP” will

appear.

(This does not mean that you can listen to the traffic

information at that time.)

When the traffic information is broadcast, “TA” will appear.

n Notes for RDS operation n To recall stations in memory

Press the TUNER (BAND) button on the remote control

or INPUT button repeatedly on the main unit to select

TUNER function.

2 Press the RDS PTY button on the remote control.

“SELECT” and “PTY TI” will appear alternately for

about 6 seconds.

3 Within 6 seconds, press the or button to select

the programme type.

Each time the button is pressed, the programme type

will appear. If the button is held down for more than

0.5 seconds, the programme type will appear

continuously.

4 Whilst the selected programme type is flashing (within

6 seconds), press the RDS PTY button again.

After the selected programme type has been lit for 2

seconds, “SEARCH” will appear, and the search

operation will start.

11/2/23 X-HM50_En.fm

En-20

Using the Radio Data System (RDS) (continued)

Descriptions of the PTY (Programme Type) codes, TP

(Traffic Programme) and TA (Traffic Announcement)

You can search for and receive the following PTY, TP and

TA signals.

NEWS Short accounts of facts, events and

publicly expressed views, reportage and

actuality.

AFFAIRS Topical programme expanding or

enlarging upon the news, generally in

different presentation style or concept,

including debate, or analysis.

INFO Programmes whose purpose is to impart

advice in the widest sense.

SPORT Programme concerned with any aspect

of sport.

EDUCATE Programme intended primarily to

educate, of which the formal element is

fundamental.

DRAMA All radio plays and serials.

CULTURE Programmes concerned with any aspect

of national or regional culture, including

language, theatre, etc.

SCIENCE Programmes about the natural sciences

and technology.

VARIED Used for mainly speech-based

programmes usually of light-

entertainment nature, not covered by

other categories. Examples include:

quizzes, panel games, personality

interviews.

POP M Commercial music, which would

generally be considered to be of current

popular appeal, often featuring in current

or recent record sales charts.

ROCK M Contemporary modern music, usually

written and performed by young

musicians.

EASY M Current contemporary music considered

to be “easy-listening”, as opposed to

Pop, Rock or Classical, or one of the

specialised music styles, Jazz, Folk or

Country. Music in this category is often

but not always, vocal, and usually of

short duration.

LIGHT M Classical music for general, rather than

specialist appreciation. Examples of

music in this category are instrumental

music, and vocal or choral works.

CLASSICS Performances of major orchestral works,

symphonies, chamber music, etc., and

including Grand Opera.

OTHER M Musical styles not fitting into any of the

other categories. Particularly used for

specialist music of which Rhythm &

Blues and Reggae are examples.

WEATHER Weather reports and forecasts and

meteorological information.

FINANCE Stock Market reports, commerce,

trading, etc.

CHILDREN For programmes targeted at a young

audience, primarily for entertainment

and interest, rather than where the

objective is to educate.

SOCIAL Programmes about people and things

that influence them individually or in

groups. Includes: sociology, history,

geography, psychology and society.

RELIGION Any aspect of beliefs and faiths, involving

a God or Gods, the nature of existence

and ethics.

PHONE IN Involving members of the public

expressing their views either by phone or

at a public forum.

TRAVEL Features and programmes concerned

with travel to near and far destinations,

package tours and travel ideas and

opportunities. Not for use for

announcements about problems, delays,

or roadworks affecting immediate travel

where TP/TA should be used.

LEISURE Programmes concerned with

recreational activities in which the

listener might participate. Examples

include, Gardening, Fishing, Antique

collecting, Cooking, Food & Wine, etc.

JAZZ Polyphonic, syncopated music

characterised by improvisation.

COUNTRY Songs which originate from, or continue

the musical tradition of the American

Southern States. Characterised by a

straightforward melody and narrative

story line.

NATION M Current Popular Music of the Nation or

Region in that country's language, as

opposed to International “Pop” which is

usually US or UK inspired and in English.

OLDIES Music from the so-called “golden age” of

popular music.

FOLK M Music which has its roots in the musical

culture of a particular nation, usually

played on acoustic instruments. The

narrative or story may be based on

historical events or people.

DOCUMENT Programme concerned with factual

matters, presented in an investigative

style.

TEST Broadcast when testing emergency

broadcast equipment or receivers.

ALARM Emergency announcement made under

exceptional circumstances to give

warning of events causing danger of a

general nature.

NONE No programme type (receive only).

TP Broadcasts which carry traffic

announcements.

TA Traffic announcements are being

broadcast.

La page charge ...

Pioneer X-HM50K-K Le manuel du propriétaire

Marque: Pioneer

Modèle: X-HM50K-K

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Pioneer X-HM50K-K Owner's manual
español: Pioneer X-HM50K-K El manual del propietario

Pioneer X-HM50K-K Le manuel du propriétaire

Ce manuel convient également à

Pioneer X-HM50K-K Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents