Intermec MobileLAN power 6 Manuel utilisateur

P/N 071787-001

User’s Guide

MobileLAN

™

power 6/12

Intermec Technologies Corporation

6001 36th Avenue West

P.O. Box 4280

Everett, WA 98203-9280

U.S. service and technical support: 1-800-755-5505

U.S. media supplies ordering information: 1-800-227-9947

Canadian service and technical support: 1-800-668-7043

Canadian media supplies ordering information: 1-800-268-6936

Outside U.S.A. and Canada: Contact your local Intermec service supplier.

The information contained herein is proprietary and is provided solely for

the purpose of allowing customers to operate and/or service Intermec

manufactured equipment and is not to be released, reproduced, or used for

any other purpose without written permission of Intermec.

Information and specifications in this manual are subject to change

without notice.

©

2001 by Intermec Technologies Corporation

The word Intermec, the Intermec logo, the term Power Bridge

MobileLAN™ Power, and Universal Access Point are either trademarks

or registered trademarks of Intermec Technologies Corporation.

Throughout this manual, trademarked names may be used. Rather than put

a trademark (™ or ®) symbol in every occurrence of a trademark name, we

state that we are using the names only in an editorial fashion, and to the

benefit of the trademark owner, with no intention of infringement.

iii

Contents

Before You Begin vii

Warranty Information vii

Safety Summary vii

Warnings, Cautions, and Notes viii

About This Guide ix

Prerequisite Skills and Knowledge ix

Introduction

Introducing the Power Bridge 1-3

About the Power Bridge 1-3

Power Bridge—Front View Detail 1-4

LEDS—6-Port Option 1-5

6-Port Power Bridge Status Indications 1-5

LEDS—12-Port Option 1-6

12-Port Power Bridge Status Indications 1-7

Power Bridge—Rear View Detail 1-8

Console Port 1-9

Information Label 1-9

Supply Data Label 1-9

AC Power Receptacle 1-9

Network Configuration Examples 1-10

Powering Ethernet Devices 1-10

1

iv

Installing and Setting Up the

Power Bridge

Installing the Power Bridge 2-3

Verifying Kit Contents 2-3

Recording Identification Information 2-4

Choosing a Suitable Site 2-4

Rack Mounting (12-Port Bridge Only) 2-5

Shelf Mounting 2-6

Setting Up the Power Bridge 2-6

Powering Up 2-6

6-Port Option 2-7

12-Port Option 2-7

Connecting Cables to the Power Bridge 2-7

Connecting Cables to End Devices 2-8

Safety Information

Important Safety Information A-3

Power Cord Set A-6

2

A

v

Specifications and

Troubleshooting

6-Port Specifications B-3

Physical Specifications B-3

Environmental Specifications B-3

Electrical Specifications B-3

Ethernet Interface B-4

Serial Port Interface B-4

12-Port Specifications B-4

Physical Specifications B-4

Environmental Specifications B-4

Electrical Specifications B-5

Ethernet Interface B-5

Serial Port Interface B-5

Troubleshooting B-5

Commonly Asked Technical Support Questions B-6

B

vii

Before You Begin

This section introduces you to standard warranty provisions, safety

precautions, and cautions and notes.

Warranty Information

To receive a copy of the standard warranty provision for this product,

contact your local Intermec sales organization. In the U.S.A, call

1-800-755-5505; in Canada, call 1-800-668-7043.

Note: Opening this product may void the warranty. The

internal workings of this product can only be accessed by

Intermec service personnel. Radio replacements and

upgrades require Intermec service personnel.

Safety Summary

Your safety is extremely important. Read and follow all warnings and

cautions in this book before handling and operating Intermec

equipment. You can be seriously injured, and equipment and data can

be damaged if you do not follow the safety warnings and cautions.

Do not repair or adjust alone

Do not repair or adjust energized

equipment alone under any circumstances. Someone capable of

providing first aid must always be present for your safety.

First aid

Always obtain first aid or medical attention immediately

after an injury. Never neglect an injury, no matter how slight it seems.

Resuscitation

Begin resuscitation immediately if someone is injured

and stops breathing. Any delay could result in death. To work on or

near high voltage, you should be familiar with approved industrial first

aid methods.

Energized Equipment

Never work on energized equipment unless

authorized by a responsible authority. Energized electrical equipment is

dangerous. Electrical shock from energized equipment can cause death.

If you must perform authorized emergency work on energized

equipment, be sure that you comply strictly with approved safety

regulations.

viii

Warnings, Cautions, and Notes

Warning

Warnings contain directions that must be followed

for personal and product safety. Follow all

directions carefully.

Avertissement

Les avertissements comprennent des instructions

qui doivent être respectées pour assurer la sécurité

des personnes et de l’équipement. Respectez

scrupuleusement toutes les instructions.

Caution

A Caution alerts you to an operating procedure,

practice, condition, or statement that must be

strictly observed to prevent equipment damage or

destruction, or corruption or loss of data.

Conseil

Une précaution vous avertit d’une procédure de

fonctionnement, d’une méthode, d’un état ou d’un

rapport qui doit être strictement respecté pour

empêcher l’endommagement ou la destruction de

l’équipement, ou l’altération ou la perte de

données.

Note: Notes either provide extra information about a

topic or contain special instructions for handling a

particular condition or set of circumstances.

ix

About This Guide

This document provides information and procedures regarding

hardware installation, setup, configuration, and management of the

Power Bridges.

Prerequisite Skills and Knowledge

This guide is intended for use by network administrators who are

responsible for installing and setting up network equipment;

consequently, it assumes a basic working knowledge of LANs (Local

Area Networks).

To use this document effectively, you should have a working

knowledge of Ethernet infrastructures. In addition, you should have a

working knowledge of the following:

•

Basic electronics and mechanical assembly, as well as an

understanding of related local building codes

•

Local operating and troubleshooting procedures

kjhkjh

Introduction

1

jh

1-3

This chapter introduces the Power Bridge and explains how it can

be used in your network.

Introducing the Power Bridge

This chapter covers the following topics:

•

About the Power Bridge

•

Power Bridge—front view detail

•

LEDs—6-port option

•

LEDs—12-port option

•

Power Bridge—rear view detail

•

Network configuration examples

•

Power Ethernet devices

About the Power Bridge

The Power Bridge is a 6/12 Ethernet channel power-feeding device.

This device is designed for use with a 10BaseT/100BaseTx standard

Ethernet network over a standard TIA/EIA-568 Category 5, 6, or 6e

cabling plant. The DC operating power for the data terminal units is fed

through the unused pairs (7/8 and 4/5).

The Power Bridge normally powers devices that are Power over LAN

Enabled or are equipped to receive power over Ethernet. Devices that

are not equipped to receive power over Ethernet require an external

splitter to be powered.

1-4

The Power Bridge features the following:

•

Remote power feeding of Ethernet terminals

•

6 or 12 10BaseT/100BaseTx data + power combined channels

•

Universal 90 to 264 VAC, 50 to 60 Hz power input

•

Independent overload and short-circuit protection for each channel

•

Port status indications as specified in this manual

•

RS-232 software download, monitoring, and control serial port

•

Standard 19-inch, 1.5U rack mountable (12-port option)

•

Stand-alone unit, 1/2x19, 1U (6-Port option)

The Power Bridge also eliminates the need for terminal’s AC outlets,

UPS, and AC/DC adapters.

Power Bridge—Front View Detail

The next illustration shows the LEDs and ports of the 6-port Power

Bridge. The LEDs and ports are explained in the next sections.

1 23456

Data In

Data & Power Out

Main

Data Input Port Port Status LEDMain Power LED

Data & Power Output Port

The next illustration shows the LEDs and ports of the 12-port Power

Bridge. The LEDs and ports are explained in the next sections.

AC

Power Active

Alarm

Power Not Active

Data & Power out

Data In

Data & Power Output Port

Data Input Port

12

3456

78

9

10 11 12

1-5

10BaseT/100BaseTx Data Input Ports, Lower 6/12 Ports

The Power

Bridge has 6/12 10BaseT/100BaseTx data input ports, configured as

Media Dependant Interface (MDI) (non-crossover). These ports are

designed to carry Ethernet data only (Tx/Rx) over the standard 2-wire

pairs (RJ-45 pins 1/2 and 3/6).

10BaseT/100BaseTx Data and Power Output Ports, Upper 6/12 Ports

The Power Bridge has 6/12 Data and Power ports configured as MDI

(non-crossover). These ports are designed to carry Ethernet data over

the standard 2-wire pairs (RJ-45 pins 1/2 and 3/6) and DC power

source over the spare wire pair (RJ-45 pins 4/5 and 7/8).

The maximum segment length from the switch/hub to the Network

Interface Card (NIC), including the Power Bridge, is 100m (328 ft), per

the IEEE 802.3 standard.

LEDS—6-Port Option

The LEDs in the unit indicate the status of the Power Bridge and its

ports.

•

One bi-color LED (Main) marks the status of the AC power and

alarm for troubleshooting.

•

One bi-color LED per port provides port status.

6-Port Power Bridge Status Indications

The following tables contain Power Bridge status information as

presented on the front panel by the LED indicators during normal

operation.

1-6

6-Port Power Bridge Status Information

Port LED Port Load Conditions Port Voltage

Off Non-active load or

unplugged port

No DC voltage is present over

the wires

Green Active load is plugged in

and complies with

normal load conditions

Continuous nominal DC

voltage is present on the spare

pairs

Orange Overload conditions or

shorted terminal port or

forced external voltage

feed (constant DC) into

the port

Power to the port is

disconnected

No DC voltage is present on

the spare pairs

Green–

Blinking

Transitional mode in

which load detection is in

process

Power is disconnected

No DC voltage is present on

the spare pair

Main LED Main Power Status Remarks

Off Main internal power supply

unit is unplugged or faulty

Main voltage too low

Green

Main power supply unit is

plugged in and under normal

operating conditions

Main voltage is within

tolerance

Green–

Blinking

Main power supply unit

voltage exceeds specified

limits

Main voltage is out of

tolerance

All power ports are

disconnected

Red or

Blinking Red

Built-in self test failed

LEDS—12-Port Option

The LEDs in the unit indicate the status of the Power Bridge and its

ports.

•

Two LEDs provide the Power Bridge status. The AC LED (green)

indicates that the Power Bridge is receiving AC power. The Alarm

LED (orange) indicates an internal fault.

1-7

•

Two LEDs (one green and one orange) per port provide port status.

The Power Active LED (green) indicates that the terminal unit has

been identified as Power over LAN Enabled and is active and

receiving power.

•

The Power Not Active LED (orange) indicates that the port is not

supplying power and is not active.

Note: In the event that an Ethernet device that is not Power

over LAN Enabled is connected to the Power Bridge

(indicated by the orange Power Not Active LED), the

Ethernet device will be unaffected because power is not

being supplied.

12-Port Power Bridge Status Indications

The following tables contain Power Bridge status information as

presented on the front panel by the LED indicators during normal

operation.

Port LED

Port Load Conditions

Port Voltage

Green–Off

Orange–Off

Non-active load or

unplugged port

No DC voltage is present

over the wires

Green–On

Orange–Off

Active load is plugged

in and complies with

normal load conditions

Continuous nominal DC

voltage is present on the

spare pairs

Green–Off

Orange–On

Overload conditions or

shorted terminal port

or forced external

voltage feed (constant

DC) into the port

Power to the port is

disconnected

No DC voltage is present

on the spare pairs

Green–On

Orange–On

Internal hardware fault

No DC voltage is present

over the wires

Green–Blinking

Orange–Off

Transitional mode in

which load detection is

in process

Power is disconnected

No DC voltage is present

over the wires

1-8

12-Port Power Bridge Status Indications (continued)

AC LED Main Power Status Remarks

Off Main internal power supply

unit is unplugged or faulty

Main voltage too low

On Main power supply unit is

plugged in and under normal

operating conditions

Main voltage is within tolerance

Blinking Main power supply unit

voltage exceeds specified

limits

Main voltage is out of tolerance

All power ports are disconnected

Alarm LED Remarks

Off Built-in self test passed

On Built-in self test failed

For LED troubleshooting, see Appendix B.

Power Bridge—Rear View Detail

The next illustrations show the rear view details of the 6-port and 12-

port Power Bridges.

6-Port Power Bridge

Caution:Shock Potential.

Disconnect the Power

Before Servicing.

CONSOLE PORT

19200, 8, 1, N

12-Port Power Bridge

CONSOLE PORT

19200, 8, 1, N

SUPPLY DATA

V~

100-240

60/50

Hz A

3-1.5

Caution: Shock Potential.

Disconnect the Power

Before Servicing.

Refer to instruction

manual for correct

selection of power

cord.

1-9

Console Port

Use the console port (DB-9 connector) to connect a terminal and to

perform local out-of-band management. The console port uses a

standard null modem cable and is set to 19,200 baud, 8 data bits, no

parity, and 1 stop bit.

Information Label

The Information label (located on the bottom of the 1-port Power

Bridge and on the rear of the 12-port Power Bridge) shows the

following:

•

Part number of the Power Bridge

•

Serial number of the Power Bridge and date code

You may need this information for fault reporting purposes.

Supply Data Label

The Supply Data label contains information regarding the total AC

power input (100 to 240 VAC), power frequency (50 to 60 Hz), and the

corresponding amperes.

Refer to Appendix A for proper selection of a power cord.

AC Power Receptacle

The Power Bridge automatically adjusts its power setting to any supply

voltage from 90 to 240 VAC.

Warning

Electrocution Hazard. Before connecting power to

the Power Bridge, please refer to the safety

information in Appendix A.

Avertissement

Risque d’électrocution. Avant de connecter

l’alimentation au Pont d’alimentation, veuillez

consulter les informations relatives à la sécurité à

l’annexe A.

1-10

Network Configuration Examples

The following illustration shows network configuration examples.

Powering Ethernet Devices

The Power Bridge may be used to power any Ethernet device with

power requirements that are within the specified powering capabilities.

As shown in the previous illustration, the Power Bridge may be used to

power end devices such as IP phones, web cameras, laptop computers,

and others.

IP phones, for example, benefit from Power over LAN in that they no

longer need an external power source connected to wall sockets, which

are unreliable due to the possibility of power interruptions.

Wireless LAN (WLAN) access points may also be enabled to receive

power using the Power Bridge. This can be very effective when

installing WLAN access points or base stations which often require

drawing power from sockets close to the ceiling, where complicated

building codes and standards for power apply.

La page charge ...

Intermec MobileLAN power 6 Manuel utilisateur

Ce manuel convient également à

Intermec MobileLAN power 6 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents