Uniden SX307-3C Le manuel du propriétaire

Marque: Uniden

Modèle: SX307-3C

Catégorie: Radios bidirectionnelles

Taper: Le manuel du propriétaire

F R S

2-way

radios

SX307

• 22 FRS Channels • Weather Channels

• 121 Privacy Codes • Weather Alert

• Channel Scan • 5 VOX levels

• Channel Monitor • 10 Call tones

• Key Lock • Roger Beep

• Beep Tone • Battery Strength Meter

• Backlight • Battery Save/Low Battery

Alert

• Volume Setting • Call Button

• Last Channel

Memory

• Up to 30-mile Range*

• Auto Squelch • Charging Kit (model names

with CK) or Y-Split micro

USB cable (model names

with C)

• microUSB Jack • Earbud/Headphone Jack

* Range may vary depending on environmental and/or

topographical conditions.

1 Antenna 8 LCD

2 Push to Talk 9 CH/VOL Up

3 Headphone/microUSB jack 10 CH/VOL Down

4 WX/LOCK 11 CH/LIGHT

5 CALL/MON 12 Microphone

6 MENU/Power 13 Charging Contacts

7 Speaker

Congratulations on your purchase of a Uniden

SX307 series radio. This lightweight, palm-sized

radio is a state-of-the-art device, equipped with

many valuable features. Use it at sporting

events, to stay in contact with family and

friends, hiking, skiing, outdoors, or in a

neighborhood watch for vital communication.

Each radio uses 3 AA rechargeable Ni MH

batteries, included.

If your model number contains a "C," your

package contains a microUSB Y charging cable.

If your model number contains "CK," it contains

a charging kit (including a charging cradle).

If your models number contains "HS," it contains

headsets.

Refer to the packaging for other specific

contents. .

Each radio uses 3 AA rechargeable NiMH

batteries (included).

1. If necessary, remove the belt clip. Press

up on the belt clip latch and slide the belt

clip off of the radio.

2. Remove the battery compartment door by

pressing on and sliding out the

compartment door. Remove the cover.

3. Install the 3 AA batteries into the battery

compartment. Be certain to follow the +

and – symbols in the compartment.

Installing the batteries incorrectly will

prevent the unit from operating.

4. Replace the battery compartment door by

sliding the door into place.

5. Replace the belt clip if necessary.

6. Replace the belt clip if necessary.

BATTERY LEVEL /

LOW LEVEL ALERT

This unit has a battery level meter on the

display to indicate the status of the batteries.

When the battery in the unit is low, the battery

level meter icon flashes and . Recharge

the batteries immediately.

CHARGING THE RADIO

For radios with microUSB Y-cable:

1. Plug one branch of the microUSB Y-Cable

into each radio's microUSB charge port.

2. Insert the other end (USB) into a USB

power source (computer, phone charger,

etc - not included).

3. Charge the batteries for 16 hours and

disconnect the radio from the Y-cable after

charging.

For radios with a charging cradle:

1. Connect the AC adapter to DC IN 9V jack

on the charger and to a standard 120V AC

wall outlet.

2. Set the charging cradle on the desk or

PACKAGE CONTENTS

INSTALL THE BATTERIES

tabletop, and place the radio in the

charging cradle with the keypad facing

forward.

3. Make sure that the LED illuminates. Charge

the batteries for 16 hours and remove the

radio from the charging cradle after

charging.

Warning!

• Neither the radio nor the charging cradle are

waterproof.

• If the charging cradle falls into water, unplug it

before attempting to remove it from the water.

Allow the cradle to dry completely before

reconnecting the power.

• Wipe off dirt or shake water from your radio

before placing in the charging cradle if your

radio is soiled or wet.

Notes:

• Install the batteries before charging. Charge

time may vary depending on the battery life

remaining. For fastest charging, turn off the

radio before charging.

• If battery power is low, you cannot operate the

radio even using external power. Allow the

batteries to charge before using. If you try to

transmit while power is low, the radio will

automatically turn off.

USING THE RADIO

In order to get the most out of your new radio,

read this reference guide completely before

attempting to operate the radio.

TURNING THE RADIO ON AND ADJUSTING

THE VOLUME

1. Press and hold the MENU/ key to turn

the radio ON.

2. Press and hold the MENU/ key to turn

the radio OFF.

3. Press the ▲ or ▼ keys to increase or

decrease the volume level. L0 - L8 displays

as you press the keys.

USING THE MENUS

Press MENU/ key to enter the Menu system.

Each time you press MENU/ key you advance

through the system.

• Press MENU/ once; access Privacy Codes

(0 - 121).

• Press MENU/ twice; set the transmit (call)

tone for your radio (1 - 10, Off)

• Press MENU/ three times - access VOX.

(Levels 1 - 5, Off)

• Press MENU/ four times - exit Menus.

WORKING WITH CHANNELS / PRIVACY

CODES

Your radio has 22 channels and 121 Privacy

Codes you can use to talk to others. In order to

speak to someone, each of you must be set to

the same channel/Privacy Code.

1. With the radio on, press CH/LIGHT key

once. The current channel number flashes.

2. Use the ▲ or ▼ keys to select other

channels (1 - 22). Press and hold ▲ or ▼

keys to rapidly change channels.

3. Press CH/LIGHT key again to set the

selected channel.

4. Press MENU/ key once. The current

Privacy Code flashes.

5. Use the ▲ or ▼ keys to select other

Privacy Codes (1 - 121). Press and hold ▲

or ▼ keys to rapidly change Privacy

codes.

6. Press MENU/ key three times to set the

Privacy Code and exit the Menus.

VOICE OPERATED TRANSMISSIOS

Your radio is equipped with a user selectable

Voice Operated Transmitter (VOX) that can be

used for automatic voice transmissions. The

VOX feature is designed to be used with a

headset with a microphone. Transmission is

initiated by speaking into the headset's

microphone instead of pushing the PTT button.

To select the VOX level:

1. Enter the Menu. Advance through the

Menu until the vox icon appears on the

display. The current level (OFF, 1-5) will be

indicated. Level oF (OFF) disables VOX,

while levels 1-5 set the sensitivity of the

VOX circuit.

2. Press either the ▲ or ▼ keys to select the

desired VOX sensitivity level. Use level 1

for increased

sensitivity to voice in normally

quiet environments

, and use a higher level

to reduce undesired activation in very noisy

environments.

CHANNEL SCAN FEATURES

Your radio has a channel scan feature that

allows you to easily scan all 22 channels. When

an active channel is detected, the unit pauses on

that channel until the channel is clear. Then,

after a 2 second delay, the radio continues

scanning.

When the unit stops on an active channel, you

can press the PTT button on the microphone to

transmit on that channel.

To turn ON channel scan

Quickly press CH/LIGHT then hold ▼ for 3

seconds. The channels will cycle down

through all 22 chanels. To reverse scan

direction, press ▲. To stop scanning,

press MENU/ .

TALKING ON YOUR RADIO

1. Press and hold the PTT button and speak

in a clear, normal voice about 2-3 inches

away from the microphone. (While you are

transmitting, the tx icon displays. To avoid

cutting off the first part of your

transmission, pause slightly after pressing

the PTT button before you start talking.)

2. When you are finished speaking, release

the PTT button. You can now receive

incoming calls. While receiving, the rx icon

displays.

KEY LOCK

1. To lock the keypad, press and hold WX

LOCK key. The icon appears on the

display.

2. To unlock the keypad, press and hold WX

LOCK key again. The icon disappears

from the display.

Note: While keylock is on, you can still use the

radio to receive, transmit, use call, turn volume

up or down, MON and MENU/ to turn the

radio on or off.

BACKLIGHT

Press and hold CH/LIGHT. A red backlight turns

on. It automatically turns off after several

seconds

TRANSMITTING A CALL ALERT TONE

Your radio is equipped with a call tone that will

be transmitted when the CALL/MON key is

pressed.

To transmit the call tone, press the CALL/MON

key. The tone will be transmitted.

AUTO SQUELCH

The radio is equipped with an automatic squelch

system which shuts off weak transmissions and

unwanted noise due to terrain conditions or

range limitations.

MONITOR MODE

Your radio allows you to listen for weak signals

on the current channel at the press of a key.

To turn ON monitor mode, Press and hold

CALL/MON for 2 seconds. The tx icon

displays. On a channel that does not have

activity, you will hear only an open-squelch

hissing noise.

To turn OFF monitor mode, press and hold the

CALL/MON key for 2 seconds again.

Channels 143 (22 Channels + 121 Privacy

Codes)

Operating

Frequency

UHF 462.5500 - 467.7125 MHz

(GMRS/FRS)

162.4000 - 162.5500 MHz (WX)

Power

Source

3 rechargeable NiMH batteries

per radio

Battery

Life

12 hours typical (5/5/90 duty

cycle)

SPECIFICATIONS

Frequency Chart

CH Freq.[MHz] -

Cross Ref.

CH Freq.[MHz] -

Cross Ref.

1 462.5625 - FRS &

GMRS 1

12 467.6625 - FRS

2 462.5875 - FRS &

GMRS 2

13 467.6875 - FRS

3 462.6125 - FRS &

GMRS 3

14 467.7125 - FRS

4 462.6375 - FRS &

GMRS 4

15 462.5500 - GMRS

5 462.6625 - FRS &

GMRS 5

16 462.5750 -

GMRS 8

6 462.6875- FRS &

GMRS 6

17 462.6000 - GMRS

7 462.7125 - FRS &

GMRS 7

18 462.6250 -

GMRS 9

8 467.5625 - FRS 8 19 462.6500 - GMRS

9 467.5875 - FRS 9 20 462.6750 - GMRS

10 467.6125 - FRS

21 462.7000 - GMRS

11 467.6375 - FRS

22 462.7250 - GMRS

Note: This product is considered FRS only with 22 FRS

channels in the US market. It is considered a

GMRS product in the Canadian market.

CTCSS Chart (Hz)

Code Freq. Code Freq.

oF OFF 20 131.8

1 67.0 21 136.5

2 71.9 22 141.3

3 74.4 23 146.2

4 77.0 24 151.4

5 79.7 25 156.7

6 82.5 26 162.2

7 85.4 27 167.9

8 88.5 28 173.8

9 91.5 29 179.9

10 94.8 30 186.2

11 97.4 31 192.8

12 100.0 32 203.5

13 103.5 33 210.7

14 107.2 34 218.1

15 110.9 35 225.7

16 114.8 36 233.6

17 118.8 37 241.8

18 123.0 38 250.3

19 127.3

MAINTENANCE

To be safe and sure:

• Never open your radio’s case.

• Never change or replace anything in your radio

except the batteries.

Your radio might cause TV or radio interference even

when it is operating properly. To determine whether

your radio is causing the interference, turn it off. If the

interference goes away, your radio is causing it. Try to

eliminate the interference by moving your radio away

from the receiver. If you cannot eliminate the

interference, the FCC requires that you stop using the

radio.

Hazardous Environments

Do not operate the radio in hazardous environments.

Explosion or fire may result. Do not operate the radio

near unshielded electrical blasting caps.

Under certain conditions, radios can interfere with

blasting operations and may cause an explosion. Turn

your radio OFF to prevent accidental transmission

when in a blasting area or in areas posted: "Turn off

two-way radio." Construction crews often use remote

control RF devices to set off explosives.

Care and Safety

To clean the radio, use a soft cloth dampened with

water. Do not use cleaners or solvents because they

can harm the body of the unit and leak inside, causing

permanent damage. Use a dry, lint-free cloth to clean

the battery contacts. Do not submerge the unit in

water. If the unit gets wet, turn it off and remove the

batteries immediately.

Dry the battery compartment with a soft cloth to

minimize potential water damage. Leave the battery

compartment cover off overnight to ensure complete

drying. Do not use the radio until the unit is completely

dry.

WARNING! Read this information before using the

radio. In August 1996 the Federal Communications

Commission (FCC) of the United States with its action

in Report and Order FCC 96-326 adopted an updated

safety standard for human exposure to radio frequency

electromagnetic energy emitted by FCC regulated

transmitters.

Those guidelines are consistent with the safety

standard previously set by both U.S. and international

standards bodies. The design of the radio complies

with the FCC guidelines and these international

standards.

Never allow children to operate the radio without adult

supervision and the knowledge of the following

guidelines.

FCC RF EXPOSURE INFORMATION

WARNING! It is up to the user to properly operate this radio

transmitter to insure safe operation. Please adhere to the

following:

Use only the supplied or an approved antenna. Unauthorized

antennas, modifications, or attachments could impair call

quality, damage the radio, or result in violation of FCC

regulations.

Do not use the radio with a damaged antenna. If a damaged

antenna comes into contact with the skin, a minor burn may result.

Please contact your local dealer for a replacement antenna.

Body-Worn Operation

This device was tested for typical body-worn operations using the

supplied belt-clip.

To maintain compliance with FCC RF exposure requirements,

body-worn operations are restricted to the supplied belt-clip.

For hand-held operation, the radio should be held 1 inch from the

user's face. The use of accessories that do not satisfy these

requirements may not comply with FCC RF exposure requirements

and should be avoided.

For more information about RF exposure, please visit the FCC web

site at www.fcc.gov.

FCC PART 15 / IC COMPLIANCE

FCC ID: AMWSX237

IC: 513C-SX307

FCC PART 15 COMPLIANCE

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void your authority to operate the

equipment.

Avis de conformité à la FCC : Ce dispositif a été testé et s’avère

conforme à l’article 15 des règlements de la Commission fédérale

des communications (FCC). Ce dispositif est soumis aux conditions

suivantes: 1) Ce dispositif ne doit pas causer d’interférences

nuisibles et; 2) Il doit pouvoir supporter les parasites qu’il reçoit,

incluant les parasites pouvant nuire à son fonctionnement.

Tout changement ou modification non approuvé expressément par

la partie responsable pourrait annuler le droit à l’utilisateur de faire

fonctionner cet équipement.

IC COMPLIANCE

This device complies with Industry Canada license-exempt RSS

standard(s).Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including

interference that may cause undesired operation of the

device.

Changes or modifications not expressly approved by the party

responsible for compliance could void your authority to operate the

equipment.

Cet appareil est conforme aux normes RSS exemptes de licences

d’Industrie Canada. Son fonctionnement est soumis aux deux

conditions suivantes :

1. Cet appareil ne doit pas causer d’interférences nuisibles et

2. Cet appareil doit accepter toute interférence, y compris les

interférences susceptibles de provoquer un fonctionnement

non désiré de l'appareil.

Tout changement ou modification non approuvé expressément par

la partie responsable pourrait annuler le droit à l’utilisateur de faire

fonctionner cet équipement.

ONE YEAR LIMITED WARRANTY

Important: Evidence of original purchase is required for warranty

service.

WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")

RBRC Information

As part of our commitment to protect the

environment and conserve natural

resources, Uniden voluntarily participates

in an RBRC

industry program to collect

and recycle used Ni-MH batteries within the US.

Please call 1-800-8-BATTERY for information on

Ni-MH battery recycling in your area. (RBRC

is a

registered trademark of the Rechargeable Battery

Recycling Corporation.)

ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original

retail owner, this Uniden Product to be free from defects in materials and

craftsmanship with only the limitations or exclusions set out below.

WARRANTY DURATION: This warranty to the original user shall terminate and

be of no further effect 12 months after the date of original retail sale. The

warranty is invalid if the Product is: (A) damaged or not maintained as

reasonable or necessary, (B) modified, altered, or used as part of any

conversion kits, sub-assemblies, or any configurations not sold by Uniden, (C)

improperly installed, (D) serviced or repaired by someone other than an

authorized Uniden service center for a defect or malfunction covered by this

warranty, (E) used in any conjunction with equipment or parts or as part of any

system not manufactured by Uniden, or (F) installed or programmed by anyone

other than as detailed by the owner’s manual for this product.

STATEMENT OF REMEDY: In the event that the product does not conform to

this warranty at any time while this warranty is in effect, warrantor will either, at

its option, repair or replace the defective unit and return it to you without charge

for parts, service, or any other cost (except shipping and handling) incurred by

warrantor or its representatives in connection with the performance of this

warranty. Warrantor, at its option, may replace the unit with a new or refurbished

unit.

THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE

WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND

EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER,

WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,

INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS

WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT

OVERPAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some

states do not allow this exclusion or limitation of incidental or consequential

damages so the above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state. This warranty is void

outside the United States of America and Canada.

PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after

following the instructions in the owner’s manual you are certain that the Product

is defective, pack the Product carefully (preferably in its original packaging). The

Product should include all parts and accessories originally packaged with the

Product. Include evidence of original purchase and a note describing the defect

that has caused you to return it.The Product should be shipped freight prepaid,

by traceable means, to warrantor:

Uniden America Corporation

C/O Saddle Creek

743 Henrietta Creek Road, Suite 100

Roanoke, TX 76262

Tone Octal

No. Code

39 023

40 025

41 026

42 031

43 032

44 043

45 047

46 051

47 054

48 065

49 071

50 072

51 073

52 074

53 114

54 115

55 116

56 125

57 131

58 132

59 134

60 143

61 152

62 155

63 156

64 162

65 165

66 172

67 174

68 205

69 223

70 226

71 243

72 244

73 245

74 251

75 261

76 263

Tone Octal

No. Code

77 265

78 271

79 306

80 311

81 315

82 331

83 343

84 346

85 351

86 364

87 365

88 371

89 411

90 412

91 413

92 423

93 431

94 432

95 445

96 464

97 465

98 466

99 503

100 506

101 516

102 532

103 546

104 565

105 606

106 612

107 624

108 627

109 631

110 632

111 654

112 662

113 664

114 703

Tone Octal

No. Code

115 712

116 723

117 731

118 732

119 734

120 743

121 754

122 036

123 053

124 122

125 145

126 212

127 225

128 246

129 252

130 255

131 266

132 274

133 325

134 332

135 356

136 446

137 452

138 454

139 455

140 462

141 523

142 526

DCS Code List

Uniden SX307-3C Le manuel du propriétaire

Marque: Uniden

Modèle: SX307-3C

Catégorie: Radios bidirectionnelles

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Uniden SX307-3C Owner's manual

Uniden SX307-3C Le manuel du propriétaire

Uniden SX307-3C Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents