User Guide
eLink 100
Wireless Extenders
HDMI Wireless Extender
68-2662-01 Rev.
I
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, ,when used on the product, is
intended to alert the user of the presence of uninsulated dangerous
voltage within the product’s enclosure that may present a risk of electric
shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению
электрическим током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
安全記事 • 繁體中文
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有
重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資
訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。
安全上のご注意 • 日本語
警告: この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 が製品上に表示されている場合は、本機の取扱説明書に
記載されている重要な操作と保守(整備)の指示についてユーザーの注意
を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウ ェブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。
Copyright
© 2014-2019 Extron Electronics. All rights reserved. www.extron.com
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks (
®
), registered service marks (
SM
), and trademarks (
TM
) are the property of RGBSystems, Inc. or
ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Glitch Free. Global
Configurator, GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink,
MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch,
StudioStation, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP,
XTPSystems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple
Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator,
DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk,
MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger,
ShareLink, SIS, SimpleInstructionSet, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, and
ZipCaddy
FCC Class B Notice
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part15 of the FCC rules. These limits provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. There is no
guarantee that interference will not occur. If this equipment does cause interference to radio
or television reception, which can be determined by turning the equipment off and on, you
are encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
In order to maintain compliance with FCC regulations, shielded cables must be used with
this equipment. Operation with non-approved equipment or unshielded cables is likely to
result in interference to radio and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of the manufacturer could void
the user’s authority to operate this equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ATTENTION:
• This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm (7.9 inches) between the radiator and your body.
• Cet équipement est conforme aux limites de radiation de la FCC établies pour un
environnement non géré. Il doit être installé et contrôlé à une distance minimale de
20 cm (7,9 inches) entre le radiateur et votre corps.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics see the “Extron Safety and Regulatory
Compliance Guide” on the Extron website.
Safety Notices
USA—FCC and FAA
The FCC with its action in ET Docket 96-8 has adopted a safety standard for human
exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified
equipment. The unit meets the Human Exposure limits found in OET Bulletin 65, supplement
C, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the
instructions found in this manual will result in exposure substantially below the FCC’s
recommended limits.
ATTENTION: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g,
and 802.11n wireless LAN devices may not yet be harmonized in all countries,
802.11a, 802.11b, 802.11g, and 802.11n products are designed for use only in
specific countries, and are not allowed to be operated in countries other than those of
designated use.
As a user of these products, you are responsible for ensuring that the products are
used only in the countries for which they were intended and for verifying that they are
configured with the correct selection of frequency and channel for the country of use.
Any deviation from the permissible power and frequency settings for the country of
use is an infringement of national law and may be punished as such.
FCC Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency
range. FCC requires this product to be used indoors for the frequency range 5.15 to
5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite
systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and
5.65 to 5.85 GHz bands.
USA—Federal Communications Commission (FCC)
NOTE: The radiated output power of the wireless network device is far below the FCC
radio frequency exposure limits. Nevertheless, the unit should be used in such a
manner that the potential for human contact during normal operation is minimized. To
avoid the possibility of exceeding the FCC radio frequency exposure limits, you should
keep a distance of at least 20 cm between you (or any other person in the vicinity) and
the antenna that is built into the unit. Details of the authorized configurations can be
found at http://www.fcc.gov/ by entering the FCC ID number on the device.
Security
IC Compliance
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.
ATTENTION:
• When using IEEE 802.11a wireless LAN, this product is restricted to indoor use
due to its operation in the 5.15 to 5.25 GHz frequency range. Industry Canada
requires this product to be used indoors for the frequency range of 5.15 GHz to
5.25 GHz to reduce the potential for harmful interference to co-channel mobile
satellite systems. High power radar is allocated as the primary user of the 5.25
to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause
interference with and/or damage to this device.
• The maximum allowed antenna gain for use with this device is 6dBi in order to
comply with the E.I.R.P limit for the 5.25 to 5.35 and 5.725 to 5.85 GHz frequency
range in point-to-point operation.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of
the device.
Radio Frequency (RF) Exposure Information
To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit
antenna) that is installed outdoors is subject to licensing.
The radiated output power of the Extron Wireless Device is below the Industry Canada (IC)
radio frequency exposure limits. The Extron Wireless Device should be used in such a
manner such that the potential for human contact during normal operation is minimized.
Extron Unit IC ID: IC: 10862A-EXT60150801
IC Antenna Statement
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter (IC:10862A-EXT60150801) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain and required
antenna impedance for each antenna type indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly prohibited for
use with this device.
Type: Dipole
Maximum Peak Gain: 2 dBi
Impedance: 50 Ohm
European Union
The low band 5.15-5.35 GHz is for indoor use only.
Consignes de sécurité :
USA—FCC et FAA
La FCC, par son action dans le dossier ET Docket 96-8, a adopté une norme de sécurité
relative à l’exposition humaine à l’énergie électromagnétique des ondes radio (RF), émise
par du matériel certifié FCC. L’unité satisfait aux restrictions relatives à l’exposition humaine,
énoncées dans le supplément C (2001) du OET Bulletin 65 et dans le standard
ANSI/IEEE C95.1 (1992). L’utilisation appropriée de cette radio, conformément aux
instructions figurant dans ce manuel, donnera lieu à une exposition nettement inférieure aux
limites recommandées par la FCC.
ATTENTION : Compte tenu de l’éventuel manque d’harmonisation des fréquences
utilisées par des périphériques LAN sans fil conformes aux standards 802.11a,
802.11b, 802.11g, et 802.11n, les produits 802.11a, 802.11b, 802.11g, et 802.11n
peuvent être utilisés uniquement dans certains pays, et ne peuvent fonctionner en
dehors des pays dans lesquels leur usage est prévu.
En tant qu’utilisateur de ces produits, vous devez veiller à ce que ces produits soient
utilisés uniquement dans les pays dans lesquels leur usage est prévu et vérifier qu’ils
soient configurés avec les fréquences et les canaux appropriés, en fonction du pays
dans lequel ils sont utilisés. Tout écart aux paramètres de puissance et de fréquence
pour le pays d’utilisation constitue une infraction à la législation locale et est passible
de sanctions.
Dispositions de la FCC en matière d’interférences électromagnétiques
Cet appareil est limité à une utilisation en intérieur du fait de son fonctionnement dans
la bande de fréquences 5,15-5,25 GHz. La FCC exige que ce produit soit utilisé en
intérieur pour la bande de fréquences de 5,15-5,25 GHz, afin de réduire les possibilités
d’interférences préjudiciables vers des systèmes mobiles par satellite affectant le même
canal. Un radar à haute puissance est désigné utilisateur principal des bandes
5,25-5,35 GHz et 5,65-5,85 GHz.
USA—Federal Communications Commission (FCC)
REMARQUE : La puissance de sortie radiée de l’appareil réseau sans fil est nettement
inférieure aux restrictions de la FCC en matière d’exposition aux ondes radio.
Néanmoins, l’unité devrait être utilisée de sorte que la possibilité de contact
humain lors d’un fonctionnement normal soit réduite. Afin d’éviter la possibilité de
dépassement des restrictions de la FCC en matière d’exposition aux ondes radio,
vous devez conserver une distance minimale de 20 cm entre vous (ou toute personne
se trouvant à proximité) et l’antenne incorporée dans l’ordinateur. Des informations
détaillées concernant les configurations autorisés sont disponibles sur
http://www.fcc.gov/ en entrant le numéro d’identification FCC de l’appareil.
Sécurité
IC conformité
Canada, avis d’Industry Canada (IC)
ATTENTION:
• L’utilisation d’un réseau local sans fil conforme à la norme IEEE 802.11a limite
l’emploi de ce produit à un usage en intérieur, du fait de son fonctionnement dans
la bande de fréquences 5,15-5,25 GHz. Industrie Canada exige que ce produit soit
utilisé en intérieur pour la bande de fréquences de 5,15-5,25 GHz, afin de réduire
les possibilités d’interférences préjudiciables vers des systèmes mobiles par
satellite. Un radar à haute puissance est désigné utilisateur principal des bandes
5,25-5,35 GHz et 5,65-5,85 GHz. Ces stations de radar peuvent causer des
interférences et/ou des dommages à cet appareil.
• Le gain maximal de l’antenne alloué pour une utilisation avec cet appareil est de
6 dBi afin de se conformer à la limitation de puissance isotrope rayonnée
équivalente (E.I.R.P) pour les bandes de fréquences 5,25-5,35 et 5,725-5,85 GHz
pour une exploitation point à point.
Cet appareil numérique de Classe B est conforme aux normes ICES-003 et RSS-210.
Cet appareil est conforme au Cahier des charges sur les normes radioélectriques (RSS) de
Industrie Canada relatif aux appareils exempts de licence. Son fonctionnement est soumis
aux deux conditions suivantes: (1) cet appareil ne doit pas causer d’interférences, et (2) cet
appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter
son fonctionnement.
Informations concernant l’exposition aux Fréquence Radio (RF)
La puissance de sortie émis par l’appareil de sans fil Extron est inférieure à la limite
d’exposition aux fréquences radio d’Industry Canada (IC). Utilisez l’appareil de sans fil
Extron de façon à minimiser les contacts humains lors du fonctionnement normale.
Extron Unit IC ID: IC: 10862A-EXT60150801
Déclaration d’antenne d’Industrie Canada (IC)
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé
pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l’intensité nécessaire à l’établissement d’une communication satisfaisante.
Le présent émetteur radio (IC:10862A-EXT60150801) a été approuvé par Industrie Canada
pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible
maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l’exploitation de l’émetteur.
Type: Dipole
Gain maximum: 2 dBi
Impédance: 50 Ohm
European Union
La basse fréquence 5,15-5,35 GHz est réservée à un usage en intérieur.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
• Risk of property damage.
• Risque de dommages matériels.
NOTE: A note draws attention to important information.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
ixeLink 100 HDMI Transmitter and Receiver • Contents
Contents
Introduction............................................................ 1
About this Guide ................................................. 1
About the eLink 100 Transmitter and Receiver .... 1
Features ............................................................. 2
Application Diagram ........................................... 3
Installation .............................................................. 4
Before Getting Started ........................................ 4
Front and Side Panel Features and
Connections ...................................................... 5
Transmitter Connections ................................. 5
Receiver Connections ..................................... 6
Installing the Plug on the Power Supply .............. 7
The eLink 100 On-Screen Display ....................... 8
Top Panel Features and Functions ...................... 8
Transmitter Buttons and LEDs ........................ 8
Receiver Buttons and LEDs ............................ 9
Operation .............................................................. 10
Operating Modes .............................................. 10
Registering the Transmitter with the Receiver .... 10
Registering Using the Remote Control .......... 10
Registering Using the Register Buttons ......... 11
Registering an Additional Receiver ................ 11
Using the Remote Control and the
OSD Menus ..................................................... 12
Remote Control Buttons ............................... 12
Using the Setup Menu .................................. 13
Reference Information ...................................... 15
Mounting the Transmitter and Receiver ............. 15
Best Practices for eLink 100
Mounting Locations ..................................... 17
Resolutions and Rates ...................................... 18
Operating Frequencies ..................................... 19
Troubleshooting ................................................ 20
eLink 100 HDMI Transmitter and Receiver • Contents x
eLink 100 HDMI Transmitter and Receiver • Introduction 1
Introduction
• About this Guide
• About the eLink 100 Transmitter and Receiver
• Features
• Application Diagram
About this Guide
This guide describes how to install, operate, and configure the Extron eLink 100 wireless
extender for High Definition Multimedia Interface (HDMI) signals. The eLink 100 extender
consists of the eLink 100 T transmitter and the eLink 100 R receiver (sold separately).
About the eLink 100 Transmitter and Receiver
The eLink 100 transmitter and receiver pair uses multi-input and multi-output (MIMO)
wireless communication technology to transmit HDMI video and multi-channel embedded
audio. This HDCP-compliant extender can send computer video resolutions up to
1920x1080, including HDTV 1080p @ 60 Hz, with less than 1 ms required to process the
video signal (latency). AES-128 encryption provides a secure link to send signals up to
100 feet (30 meters).
The eLink 100 T transmitter uses the 5 GHz spectrum to transmit signals. In addition to
point-to-point applications, one transmitter can be linked with up to four eLink 100 R
receivers, allowing a single source such as a digital signage player to support multiple
displays.
The transmitter and receiver are wirelessly compatible only with each other, but they can
wirelessly extend any Extron product that has HDMI connectivity, including switchers and
scalers. The transmitter can be connected to any Extron HDMI output with a signal up to
1080p @ 60 Hz. The receiver can be connected to any Extron HDMI input.
NOTE: If using the eLink 100 as an extender to a switcher output, select a switcher with
an integrated scaler or signal processor for fastest switch times (see
www.extron.com for switcher part numbers).
The eLink 100 is ideal for use in professional AV environments such as presentation spaces,
rental and staging, and digital signage.
eLink 100 HDMI Transmitter and Receiver • Introduction 2
Features
• Input — HDMI connector on eLink 100 T transmitter
Output — HDMI connector on eLink 100 R receiver
• Transmits HDMI video and multi-channel audio signals wirelessly up to
100 feet (30 meters) in professional AV environments.
• Transmission through common obstacles — The eLink 100 wireless extender
works in the 5 GHz spectrum to allow for broad coverage and transmission through
walls and furniture. Line-of-sight is not required but can maximize range.
• Resolutions and rates — Supports computer video up to 1920x1080, including
HDTV 1080p @ 60 Hz (see the Resolutions and Rates table on page 18).
• On-screen display (OSD) — The OSD provides an interface for simplified setup and
configuration.
• IR remote control — The eLink IR remote control, included with the receiver, enables
use of the OSD on the output screen for configuration and setup.
• Power supplies — Each unit includes an external 5 VDC power supply, which accepts
100 to 240 VAC, 50-60 Hz input. A DC-to-USB adapter is also provided with the
receiver, enabling the power supply to power the receiver through its USB port.
• AES 128 encryption — Supports Advanced Encryption Standard (AES) 128 data
encryption standard.
• HDMI features — Supported HDMI specification features include data rates up to
6.75 Gbps, Deep Color up to 12-bit, 3D, and multi-channel audio formats.
• HDCP compliant
• Ultra-low latency — Less than one millisecond of latency in transmission of video and
audio signals
• Dynamic Frequency Selection (DFS) —
• Actively monitors the radio frequency (RF) spectrum to select the most appropriate
frequencies, and prevents interference from other devices operating in the
spectrum.
• Takes advantage of DFS frequencies that are reserved for radar and weather
purposes (see the Operating Frequencies table on page 19 for more information).
• Embedded audio — Compatible with a broad range of multi-channel audio signals,
providing reliable operation with HDMI devices and surround sound systems.
• MIMO (multi-input and multi-output) — MIMO technology ensures that wireless
connections are stable and function in environments with multipath signals.
• Wireless transmission to as many as four receivers — The transmitter can support
up to four receivers, allowing a single source such as a digital signage player to support
multiple displays.
eLink 100 HDMI Transmitter and Receiver • Introduction 3
Application Diagram
100-240V ~ 50/60 Hz
-- A MAX
1
2
CONFIGURABLE
HDMI
IN1606
HDMI
5
6
HDMI
A
B
3
4
INPUTS OUTPUTSAUDIO INPUTSOUTPUTS REMOTE
L1
R
L2
R
L3
R
L4
R
L5
R
+48V
+48V
12
LR
VARIABLE
Tx Rx
RS-232
G
LAN
RESET
1
2
MIC/LINE
L6
R
FLEX I/O
SWITCHED 12VDC
40W MAX TOTAL
LAN
1234G
COM1
Tx Rx GGGG
RTS CTS
IR/SERIAL
1
SGSG
2
RELAY
3
SGSG
+-+-
+- +-
4 1 21 2 3 4
3 4
5
SGSG
6 7
SGSG
8 5 6 7 8
COM2
Tx Rx
COM3
Tx Rx
COM7
Tx Rx
COM4
Tx Rx GGGG
RTS CTS
COM5
Tx Rx
COM6
Tx Rx
COM8
Tx Rx
5A MAX
100-240V 50-60Hz
POWER
5V
1.5A MAX
HDMI
HDMI OUT
HDMI IN
IR OUT
STANDBY/ON
PQLS HDMI OPEN/CLOSE FL OFF
USB
WiFi
1234
!
1
@
2
#
3
$
4
%
5
^
6
&
7
*
8
(
9
)
0
_
-
+
=
|
\
}
]
{
[
~
`
QWERTYUIOP
“
‘
:
;
<
,
>
.
?
/
ASDFGHJ
ZXCVBNM
KL
control
shift
caps lock
tab
esc
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10F11 F12 F13 F14 F15 F16 F17 F18 F19
alt
option command
delete
fn home clear
enter
=/
*
8
-
5
2
7
0.
4
1
+
9
6
3
page
up
page
down
enddelete
command option control
shift
return
Blu-ray Player
Ethernet
Ethernet
Ethernet
Extron
IN1606
Scaling Presentation
Switcher
TCP/IP
Network
Microphones
1 and 2
Display
VGA
Audio
RS-232
AudioAudio
Audio
S-video
HDMI with
Embedded
Audio
HDMI with
Embedded
Audio
HDMI with
Embedded
Audio
HDMI with
Embedded
Audio
DisplayPort
to HDMI
Adapter
Extron
IPCP 505
Control Processor
Extron
TLP 1000TV
10" Tabletop
TouchLink
Touchpanel
Extron
eLink 100 T
Wireless HDMI
Transmitter
Extron
eLink 100 R
Wireless HDMI
Receiver
Document
Camera
PC
Laptop
Laptop
Wireless up to 100' (30 m)
Figure 1. Example of an eLink 100 Transmitter and Receiver Application
eLink 100 HDMI Transmitter and Receiver • Installation 4
Installation
This section provides instructions for installing the eLink 100 extender, including:
• Before Getting Started
• Front and Side Panel Features and Connections
• Installing the Plug on the Power Supply
• The eLink 100 On-Screen Display
• Top Panel Features and Functions
Before Getting Started
If mounting is required before cabling and setting up the eLink 100 units, see Mounting the
Transmitter and Receiver on page 15 for mounting instructions.
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé
uniquement.
• These units are not suitable for use in air handling spaces.
• Ces unites ne sont pas appropriées pour une utilisation dans les espaces
d’aération.
NOTE: For best performance:
• Ensure that the installation location is suitable for good signal transmission.
• For optimal signal range, avoid obstructions, such as walls, furniture or rack
enclosures, between the transmitter and receiver locations. Denser wall materials
can cause signal reduction.
• Maximum transmission distance is 100 feet (30 meters) with a clear line-of-sight.
• Up to four transmitter units can operate in the same room or environment. If
a maximum of four transmitters is reached, the next group of units should be
separated to prevent interference (see Best Practices for eLink 100 Mounting
Locations on page 17).
• Maintain a distance of at least 6.5 feet (2 meters) between multiple eLink
transmitters or multiple eLink receivers. Be mindful of units located beyond walls in
adjacent rooms.
• Maintain a distance of at least 6.5 feet (2 meters) between the eLink 100 units and
other 5 GHz RF devices. RF products can cause interference or traffic in the 5 GHz
frequency band. Monitor the 5 GHz frequency band and plan systems to avoid
traffic.
• Do not block the eLink 100 air ventilation openings and ensure proper air ventilation
around the units.
• Be careful when handling the eLink 100 units as they become hot during operation.
• Do not install above ceiling tiles. The eLink 100 is not UL Listed for use in plenum
air handling spaces.
eLink 100 HDMI Transmitter and Receiver • Installation 5
Front and Side Panel Features and Connections
Transmitter Connections
POWER
SERVICE
5V
1.5A MAX
HDMI IN
IR OUT
Front Panel
A
Side Panel
C
B
Figure 2. eLink 100 T Transmitter Side Panels
A
Power input connector — Plug the external 5 VDC power supply into this 5 V jack
to power the transmitter.
NOTES:
• Use only the power supply provided by Extron (see the Attention on page 7 for
important information).
• The USB mini-B port to the right of this connector is reserved for use by Extron
service personnel.
• See Installing the Plug on the Power Supply on page 7 if a different power
supply plug is needed for your location.
B
HDMI In connector — Connect an HDMI cable between this port and the HDMI
output port of the digital video source device.
C
IR Out connector — (Optional) Connect the tip-ring-sleeve end of the provided IR
emitter to this IR Out connector. Use the included double-sided adhesive tape to attach
the head of the IR emitter directly over the IR receiver window of the source device.
IR remote signals are passed from the receiver to the IR Out connector on the
transmitter. This feature allows the user to point the remote control toward the receiver
(by the display) instead of the source device, should the source device be in a different
location.
NOTE: This feature also applies to applications with multiple receivers (see
Operating Modes on page 10 for details on applications with more than one
receiver). IR remote signals are passed from any of the registered receivers to the
transmitter.
eLink 100 HDMI Transmitter and Receiver • Installation 6
Receiver Connections
POWER
5V
1.5A MAX
HDMI
HDMI OUT
BB
Back Panel
Figure 3. eLink 100 R Receiver Side Panel
A
IR sensor — Receives IR commands from the included IR remote control unit and the
IR remote of the source device.
NOTES:
• The IR sensor is compatible only with 38 kHz IR carrier frequency. See the
specifications for the IR remote of the source device or contact the device
manufacturer to verify the compatibility of the IR remote frequency.
• Make sure that the receiver IR sensor faces forward if using a source device IR
remote to pass signals back to the transmitter. Wall mounting or concealing the
receiver causes the IR sensor to be unreachable.
B
USB Power connector — Connect the USB end of the provided 5 V jack-to-USB
adapter to this USB mini-B connector. Connect the other end of the adapter to the
provided 5 VDC power supply.
NOTE: Use only the power supply provided by Extron (see the Attention on the
next page for important information).
To Power Supply
To USB Power
Connector on
Receiver.
C
HDMI Out connector — Connect an HDMI cable between this port and the HDMI
input connector of the display device.
eLink 100 HDMI Transmitter and Receiver • Installation 7
ATTENTION:
• This product is intended to be supplied by a Listed Power Unit marked “Class 2”
or “LPS,” rated 5 VDC, 1.5 A minimum. Always use a power supply supplied by
or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the end product.
• Ce produit est destiné à une utilisation avec une source d’alimentation listéeUL
avec l’appellation «Classe2» ou «LPS» et normée 5Vcc, 1,5A minimum.
Utilisez toujours les sources d’alimentation recommandées par Extron. L’utilisation
d’une source d’alimentation non autorisée annule toute conformité réglementaire
et peut endommager la source d’alimentation ainsi que le produit final.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air
handling spaces or in wall cavities.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to a
building structure or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16. La source d’alimentation ne devra pas être fixée de
façon permanente à une structure de bâtiment ou à une structure similaire.
Installing the Plug on the Power Supply
Each eLink 100 power supply kit contains a set of four plugs for use in different outlet types:
US
Australia
Europe
UK/Singapore/UAE
Saudi Arabia/Qatar
Figure 4. Included Power Supply Plugs
Select the appropriate plug for your location and follow the instructions below to install it on
the power supply.
1. Slide the tab at the top of the power plug under the top edge of the recess in the power
supply (see figure 5,
1
).
2. Press down on the plug until it snaps into place in the power supply recess (
2
).
22
11
Figure 5. Inserting the Plug Into the eLink 100 Power Supply
To remove a power plug from the power supply, press downward on the latch (marked
with an arrow) below the plug recess.
eLink 100 HDMI Transmitter and Receiver • Installation 8
The eLink 100 On-Screen Display
When the receiver is powered and connected to the display device, the On-screen Display
(OSD) appears (see the Operation section on page 10 for instructions on using the OSD).
Top Panel Features and Functions
The eLink 100 controls and indicators are located on the top panels of the transmitter and
receiver.
Transmitter Buttons and LEDs
DD
E
E
POWER
VIDEO
eLINK 100 T
LINK
REGISTER
RESET
Extron
AA
BB
CC
Figure 6. eLink 100 T Transmitter Top Panel
A
Link LED — Blinks while the receiver is searching for a link to register with the
transmitter (see Registering the Transmitter with the Receiver on page 10). When a
link has been made, this LED lights steadily.
B
Video LED — If the transmitter is registered with the receiver, this LED lights steadily
when a valid source video format is detected and transmitted (see Resolutions and
Rates table on page 18).
C
Power LED — Lights steadily while power is connected to the transmitter.
D
Register button — Hold this button after starting the registration process on the
receiver (see Registering the Transmitter with the Receiver on page 10).
E
Reset button — Press this button to reset the transmitter, if needed for troubleshooting
(see Troubleshooting on page 20).
eLink 100 HDMI Transmitter and Receiver • Installation 9
Receiver Buttons and LEDs
DD
E
E
POWER
VIDEO
eLINK 100 T
LINK
REGISTER
RESET
Extron
AA
BB
CC
Extron
eLINK 100 R
VIDEO
POWER
REGISTER
LINK
AA
BB
CC
DD
Figure 7. eLink 100 R Receiver Top Panel
A
Power button — Hold this button to power on the eLink 100 receiver. The blue LED
behind this button lights to indicate that power is on.
NOTE: By default, the blue LED in this button lights and the receiver is powered on
when power is connected to the unit.
B
Register button — Press this button to initiate the registration process between the
receiver and transmitter (see Registering the Transmitter with the Receiver on
the next page).
C
Link LED — This blue LED blinks while the receiver is searching for a transmitter (see
Registering the Transmitter with the Receiver). When a link has been made, this
LED lights steadily.
D
Video LED — This blue LED lights steadily when the transmitter and receiver are linked
and a valid source video format is detected.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
dans d''autres langues
- English: Extron eLink 100 User manual
Documents connexes
-
Extron ShareLink 250 Series Manuel utilisateur
-
-
-
-
Extron TLP Pro 525T Manuel utilisateur
-
-
-
Extron FOXBOX T HD-SDI Manuel utilisateur
-
-
Autres documents
-
Nyrius NPCS550V1 Guide de démarrage rapide
-
Amazon GA5Z9L Fire TV Cube Handsfree Streaming Device Manuel utilisateur
-
geratech WHD100 Manuel utilisateur
-
iogear GW3DHDKIT Information produit
-
ClimateMaster AST014 - Remote Wireless Sensor Le manuel du propriétaire
-
Radiodetection RD7000 Mode d'emploi
-
Astralpool LumiPlus Installation and Maintenance Manual
