Pioneer SDA-BS900 Le manuel du propriétaire

SDA-BS900

BLIND SPOT DETECTION

/ LANE CHANGE ASSIST SYSTEM

Instruction Manual

and Installation Guide

Important (Serial number)

The serial number is located on the bottom of the main unit. For your own security and

convenience, be sure to record the number.

English

Precaution................................................................3

Information to Customer.............................................................3

Important Safety Information.....................................................4

After-Sales Service .......................................................................5

Three Year Limited Warranty.......................................................5

Visit our Website ..........................................................................5

Alert Conditions.......................................................6

System Indicators.....................................................6

Item List ....................................................................7

Installation Diagram ................................................8

Wire Connection Diagram .......................................9

Installation Guide ..................................................10

Step 1: Sensor heads Installation .............................................11

Step 2: Left/Right Turn Signal Installation...............................12

Step 3: LED Indicator Installation .............................................13

Step 4: Speaker Installation.......................................................13

Step 5: GPS Antenna Installation ..............................................14

Step 6: Wires Installation ..........................................................14

Technical Specifications ........................................15

Troubleshooting.....................................................16

Contents

Thank you for buying this Pioneer product.

Please read through these instructions so you will know how to

operate this product properly. After you have finished reading the

instructions, keep this document in a safe place for future reference.

-2-

English

Precaution

Information to Customer

FCC ID:

IC: 25782-SDABS900

- This device contains license-exempt transmitter(s)/receiver(s) that complies with Part 15 of FCC

Rules and Innovation, Science, and Economic Development Canada license-exempt RSS(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of this device.

-

IYASDA-BS900

The antenna cannot be removed (or replaced) by user.

This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED

radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are

deemed to comply without Maximum Permissible Exposure evaluation (MPE), but the equipment

should be installed and operated at least 20cm from a person’s body.

Information to User

- Alteration or modifications carried out without appropriate authorization may invalidate the user's

right to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FEDERAL COMMUNICATIONS COMMISSION SUPPLIER'S DECLARATION OF CONFORMITY

Product Name:

Model Number: SDA-BS900

Responsible Party Name: PIONEER ELECTRONICS (USA) INC.

SERVICE SUPPORT DIVISION

Address: 2050 W. 190TH STREET, SUITE 100, TORRANCE, CA 90504, U.S.A.

Phone: 1-800-421-1404

URL: http://www.pioneerelectronics.com

BLIND SPOT DETECTION / LANE CHANGE ASSIST SYSTEM

-3-

CAN ICES-3 B/NMB-3 B

English

Important Safety Information

This system can be used on any vehicle except vehicles with metal bumpers, i.e. Trucks. When

mounting the sensors, assure that the sensors are not obstructed by any metal object as the

operation of the product can be affected by the metal object interfering with the system.

The following may compromise the effectiveness of the system:

Vehicles with metal obstructions in front of the sensor head.

Improperly mounted sensor location on vehicle, i.e. center of vehicles bumper location.

Situations that cannot be detected

Your vehicle is moving slower than the sensing speed setting, such as in slow moving traffic.

When your vehicle is reversing, the relative speed between your vehicle and objects is less than

5 mph (8 km/h).

If a vehicle is approaching / overtaking your vehicle and the relative speed between your vehicle

and the overtaking vehicle is greater than 37 mph (60 km/h). For example, if you are traveling at

41 mph (66 km/h), the system cannot detect vehicles approaching from behind if their speed

exceeds 78 mph (126 km/h).

Situations that may affect system detection accuracy

Metal objects are in the direct path of the sensing signal.

Weather such as heavy rain and snow, and icy road conditions, which can cause changes in

sensitivity.

Gravel roads, which may cause interference due to dust and flying stones.

・Incorrect installation angle.

・

THIS PRODUCT FUNCTIONS AS AN AID

FOR NOTIFYING THE PRESENCE OF OBSTACLES IN VEHICLE BLIND SPOTS.

IT DOES NOT DETECT ALL DANGERS AND OBSTACLES

AND IS NOT A SUBSTITUTE FOR YOUR JUDGEMENT AND CAREFUL ATTENTION.

BEFORE ANY MANEUVER, VISUALLY CHECK BOTH SIDES OF THE VEHICLE TO CONFIRM.

WARNING

Check sensor heads installation before driving.

- Are the screws loose?

- Is the unit firmly secured?

- If the unit comes loose while you are driving, it may cause an accident.

・

・Pioneer does not recommend that you install this product yourself. This product is designed for

professional installation only. We recommend that only authorized Pioneer service company

personnel who have specialized training and experience in mobile electronics set up and

install this product. NEVER SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product

and its connecting cables may expose you to the risk of electric shock or other hazards, and can

cause damage to this product that is not covered by warranty.

-4-

CAUTION

・Special vehicle conditions that should be considered

During system startup and initialization, it may take up to 2 minutes for the system to establish a GPS

connection. If the vehicle is driven before a GPS connection is established or if the GPS connection is

interrupted (inside a tunnel, parking structure, etc.), the system may not function properly, producing

incorrect or false warnings or failing to produce a warning. Once the GPS connection is established

or re-established, both LED indicators will flash twice to indicate the system is ready for use.

English

After-Sales Service

Please contact the authorized Pioneer dealer from which you purchased this product for after-sales

service (including warranty service) or any other information. If you still need help, please contact

our Customer Support Division.

Please do not ship your product in for repair without first contacting Customer Support for return

authorization. Please review the Limited Warranty for instructions on receiving warranty service.

-USA & CANADA

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION

P.O. Box 1720 Long Beach, CA 90801-1720

Visit our Website

Visit us at the following sites:

In the U.S.: http://www.pioneerelectronics.com

In Canada: http://www.pioneerelectronics.ca

Register your product.

Receive updates on the latest products and technologies.

Download owner’s manuals, order product catalogs, research new products, and much more.

1

2

3

Three Year Limited Warranty

When purchased from an authorized Pioneer dealer, this product is covered by Pioneer’s Three Year

Limited Warranty. Please visit http://pioneerelectronics.com/warranty to review and download

the full terms and conditions of the Limited Warranty, or you can receive a copy by calling

1-800-421-1404 or writing to the address below.

Customer Support:

Pioneer Electronics (USA) Inc.

P.O. Box 1720, Long Beach, California 90801 U.S.A.

-5-

・Electrical shock, damage to the product, smoke, and overheating could result from contact with

liquids. (The sensor heads are waterproof with IP65 rating)

・Do not disassemble or modify this product, as there are high-voltage components inside that may

cause an electric shock. Be sure to consult your dealer or the nearest authorized Pioneer service

company for internal inspection, adjustments or repairs.

・Always observe safe driving rules and follow all existing traffic regulations. If you experience difficulty

in operating this product, pull over, park your vehicle in a safe location and apply the parking brake

before making the necessary adjustments.

・Keep this manual handy as a reference for operating procedures and safety information.

English

When the system is on and functioning, the system is designed to detect the following events:

1. Blind spots while driving: Objects in the blind spot areas around your vehicle-in the lanes on the

left/right and directly behind the vehicle at a distance of up to 82 ft (approximately 25 m).

2. Blind spots while being passed / overtaken: When vehicles are approaching / overtaking your vehicle

from behind, or when your vehicle approaches and passes a moving vehicle.

3. Cross-Traffic Detection: When your vehicle is reversing, vehicles approaching from your left and

right.

Alert Conditions

System Indicators

A. When the system is turned on each time (your vehicle ignition or ACC is switched on), both LED

indicators will flash once to indicate system start up and initialization. Once a GPS connection is

established, which may take up to 2 minutes, both LED indicators will flash twice to indicate the

system is ready for use. The GPS connection is used to calculate your vehicle's speed.

When your vehicle is traveling slower than the start speed setting 18mph(29km/h), the system will

not produce warnings.

B.

1. The Right LED indicator will illuminate and remain illuminated when there is an object or vehicle

approaching,

2. If your vehicle's right turn signal is activated when there is an object or vehicle approaching,

the Right LED indicator will flash

repeatedly and the included .

C.

1. The Left LED indicator will illuminate and remain illuminated when there is an object or vehicle

approaching, or when your vehicle approaches and passes a moving vehicle.

2. If your vehicle's left turn signal is activated when there is an object or vehicle approaching,

, the Left LED indicator will flash

repeatedly and the

Blind spot detection toward the right rear of your vehicle:

speaker will beep (bi-bi-bi) one time

Blind spot detection toward the left rear of your vehicle:

speaker will beep (bi-bi-bi) one time

or when your vehicle approaches and passes a moving vehicle.

or

when your vehicle approaches and passes a moving vehicle,

or

when your vehicle approaches and passes a moving vehicle

included .

D. Cross-Traffic Detection:

1. When your vehicle is reversing and the system detects an object or vehicle approaching from your

right, the right LED indicator will illuminate and remain illuminated and the included speaker will

beep repeatedly.

-6-

CAUTION

The SDA-BS900 can not only objects approaching your vehicle from behind, but also detect

objects your vehicle is approaching or overtaking. Under certain driving scenarios, the SDA-BS900

may detect objects in an unintended way. The following conditions below are examples of scenarios

where fault notifications may occur

detect

.

Fig 1

Fig 2

Fig 3

Fig 4

English

Item List

Required tools for installation: Insulation tape; Multi-meter; Screwdriver; Cleaning cloth; ;

; Rivet gun; Clamps; Pry Tools.

Drill Bit

Rivets; Mounting bracket, electric drill

-7-

*3M and the 3M logo are registered trademarks of 3M Company.

GPS Tieline

Number

Item Name

Quantity

Pictures

Radar sensor

2 PC

1 SET

1 PC

LED Indicators

1 SET

GPS Antenna

1 PC

Speaker

1 PC

Extra LED Indicator Lens

and Double Sided Tape

2 SET

Installation Angle Tool

1 PCS

Main Harness

LED Extension Cable

1 SET

Drill Bit, Rivets

and Mounting bracket

Drill 1PC&

Rivets 12PCS

Mounting Bracket 1SET

1

2

3

4

5

6

7

8

9

10

2. When your vehicle is reversing and the system detects an object or vehicle approaching from

your left, the Left LED indicator will illuminate and remain illuminated and the included speaker

will beep repeatedly.

Note: The system will not detect or warn of standing objects or objects moving under

5 mph (8 km/h).

English

Installation Diagram

-8-

Note: If you cannot connect to the rear tail lamp (turn signal lights combined with brake lights),

then connect at the front fuse box.

English

⑮

⑬

⑪

Wire Connection Diagram

-9-

③

④

⑤

①

②

⑥

⑦

⑧

⑨

⑩

⑫

⑭

⑯

⑰

⑱

Left sensor

Left LED

indicator

Right sensor

Right LED

indicator

Speaker

GPS Antenna

FUSE (2 A)

① Left sensor cable - 1.6 ft (50 cm)

② Right sensor cable - 1.6 ft (50 cm)

③ Left sensor connector - 5.5 ft (170 cm)

④ Right sensor connector - 5.5 ft (170 cm)

⑤ Sensor extension cable - 16.4 ft (500 cm)

⑥ Main connector cables - 1.4 ft (45 cm)

⑦ GPS circuit board cable - 1.3 ft (40cm)

⑧ Left LED extension cable - 22.9 ft (700 cm)

⑨ Right LED extension cable - 22.9 ft (700 cm)

⑩ Speaker cable - 10.5 ft (320 cm)

⑪ Green reverse trigger wire - 7.5 ft (230 cm)

⑫ Pink left-turn signal trigger wire - 7.5 ft (230 cm)

⑬ Orange right-turn signal trigger wire -

7.5 ft (230 cm)

⑭ Black GND - 7.5 ft (230 cm)

⑮ Red ACC/IGN - 15.7 ft (480 cm)

⑯ GPS antenna - 10.5 ft (320 cm)

Red Left LED indicator cable - 1.6 ft (50 cm)

Yellow Right LED indicator cable - 1.6 ft (50 cm)

⑰

⑱

If cannot be connected to rear tail lamp (turn

signal lights maybe combined with brake lights)

then connect at the front fuse box.

GPS circuit board

English

Installation Guide

Do not install the LED Indicators where it may (i) obstruct the driver's vision, (ii) impair the

performance of any of the vehicle's operating systems or safety features, including air bags or

hazard lamp buttons or (iii) impair the driver's ability to safety operate the vehicle.

Never install this product in front of or next to the place in the dashboard, door, or pillar from

which one of your vehicle's airbags would deploy. Please refer to the vehicle's owner's manual for

reference to the deployment area of the airbags.

Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain

exposed.

Make sure that the cables and wires will not interfere with or become caught in any of the

vehicle's moving parts, especially brake, doors, or any of the vehicle's controls.

If the wiring of this unit is located under a front seat, make sure it does not obstruct seat movement.

Route all leads and cords carefully around the sliding mechanism so they do not get caught or

pinched in the mechanism and cause a short circuit.

Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resistor or filter, etc.)

may fail to work properly.

When replacing the fuse, be sure to use a fuse only of the rating prescribed on this product.

Use only the parts included with the unit to ensure proper installation. The use of unauthorized

parts can cause malfunctions.

Never feed power to other electronic products by cutting the insulation of the power supply lead of

this product and tapping into the lead. The current capacity of the lead will be exceeded, causing

overheating.

Use this unit with a 12-volt battery and negative grounding only. Failure to do so may result in a fire

or malfunction.

Disconnect the negative terminal of the battery before installation.

Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring that comes

into contact with metal parts to protect the wiring.

Do not perform installation in rain or fog.

・For professional installation only by personnel with specialized training and experience in mobile

electronics.

・

・The graphical symbol placed on the product means direct current.

・

WARNING

-10-

CAUTION

Ensure that the connector is inserted correctly and according to the corresponding label and the

arrow marks of the wire connector at the connection point. When connecting, ensure that the KEY

or raised area of the connector mates with the opposite connector. Do not force any connection

and ensure that the connector mates properly.

To avoid any damage to the connectors, align the arrows on each of the corresponding items, then

firmly press connectors together to ensure a good connection. Failure to properly install and

connect the system components may cause damage to the product and operation of the system.

・

English

Step 1: Sensor heads Installation

Mounting Radar Pucks with Provided Adjustable Brackets:

1) Prepare Materials brackets and radar heads (see Fig 5).

2) Mount the sensor module on the bracket with screws of the assemble bag (see Fig 6).

3) After found angle is set, firmly screw or bolt the bracket to the car (see Fig 7).

Fig 5

Fig 6

Fig 7

Use Supplied Tool to Set Proper Radar Puck Angle: the default installation angle is: 38 degree.

Depending on actual situation, the install angle could be adjusted accordingly.

Two sensors will respectively installed the vehicle rear left and right corner parts, in the bumper

(see Fig 8).

Height of sensor installation should be between the lowest line of tail lights and the highest line

of fog lights (see Fig 9).

Please following installation guide view to installed the sensors as below:

Please see illustration below, for correct guidance and mounting position of sensors with angle tool

(see Fig 10, Fig 11).

Note: Place the flat side of angle tool on the front of the sensor head, align the arrow of the angle tool

to point towards the back of the vehicle ( see Fig10, Fig 11).

38° 38°

sensor sensor

Rear

Car direction

Launch

direction

Launch

direction

Top view

Front

Side view

Tail light

The lowest line

of tail lights

The highest line

of fog lights

Fog light

Fig 8

Fig 9

-11-

English

When installing the sensor, keep the metal back side close to the mounting surface, keep both sides of

the sensor perpendicular to the ground (see Fig 12).

To make sure the sensor is correctly oriented, make sure the wire is exiting from the left/right side of

the sensor specific to their mounting side. The sensor should be installed as shown in the figure below

(The cable can be routed on the top or bottom of the sensor as shown in the figure below, but do not

route the cable in front of the sensor surface) (see Fig 13, Fig 14, Fig 15, Fig 16, Fig 17).

Top view

sensor sensor

Front

Rear

Install ruler Install ruler

Fig 10

Fig 11

Fig 13

Fig 12

Fig 14

Using a voltage multi-meter, locate the isolated left and isolated right turn signal trigger wires,

commonly found behind the vehicle's left and right tail lamp assemblies.

Once verified, connect the left and right turning signal wires to the appropriate corresponding input

wires of the SDA-BS900 wire harness (see Fig 18, Fig 19, Fig 20). Turn signal inputs of SDA-BS900 is

+12VDC only (not switchable to -12VCD); please check with a voltage multi-meter.

If turn signal lights are

combined with brake lights, then connect the turn signal trigger wires at the front fuse box.

Step 2: Left/Right Turn Signal Installation

-12-

Sensor connect wire

Horizon Horizon

90° 90°

UP

Down

Left Right

The wires is routed

at bottom side of sensor

UP

Down

Fig 16

Fig 15

Fig 17

The wires is routed

at top side of sensor

English

Step 3: LED Indicator Installation

Install the Left LED indicator and Right LED indicator in a location that is visible to the driver, ideally in

or around the vehicle's A-pillars (see Fig 21, Fig 22). Place the LED indicators away from the side curtain

air bags, so as not to hinder the deployment of airbag function. Appropriate placement is usually at the

lowest part of the A-pillars, but you must consult the vehicle manual.

Fig 21

Fig 22

NOTE:

・Changing the LED housing color

The system includes two options for the LED indicator housing. Depending on the customer’s choice

and/or vehicle’s interior color, you may change the LED cover from grey (default) to black.

1. First peel back 3M® tape from the LED indicator housing.

2. Using a small flat head screwdriver, remove the cover.

3. Align wire notch from the new cover, and snap into place.

4. Use the supplied 3M tape and re-apply behind LED.

Step 4: Speaker Installation

While installing the speaker, make sure it is not obstructed by any panels inside the vehicle

(see Fig 23).

NOTE:

To adjust volume on the speaker, toggle the switch to the desired setting, “HI/LOW/OFF”.

-13-

Fig 18

Fig 19

Fig 20

Fig 23

English

Step 6: Wires Installation

Soldering all wiring is recommended. Securely tape and insulate all connections soldered.

・

・Secure all wires neatly to hide and prevent wire pinch.

1. +12 VDC ACC/IGN - Locate the +12 VDC (ACC/IGN) and connect the red wire from the Main harness.

2. Chassis Ground (Black) - Connect the black wire from the Main harness to chassis ground.

3. +12 VDC reverse signal (Green) - Locate the +12 VDC reverse signal (reverse light or other location)

and connect the green wire from the Main harness.

4. Orange Right-Turn signal Trigger - Locate the +12 VDC Isolated turn signal and connect the Right

(Orange) wire from the Main harness.

5. Pink Left-Turn Signal Trigger - Locate the +12 VDC Isolated turn signal and connect the Left (Pink)

wire from the Main harness.

6. Connect the Main harness into the sensors.

7. Make all the appropriate connections (LED’s, Speaker, sensors) on the Main harness.

8.

9. Test the system’s operation, ensuring that all features operate according to this manual. After

operation is tested, finalize connections and secure wires.

Connect the negative terminal of the battery to the vehicle.

-14-

Fig 24

When installing the GPS Antenna, make sure it is not obstructed by any panels inside the vehicle

(see Fig 24).

Step 5: GPS Antenna Installation

English

Technical Specifications

-15-

70 degrees ( ) HorizontalDetection Range

Speed Range 0.5 mph (-36 km/h) 37 mph (60 km/h)～

Speed Accuracy

< 0.5 mph (0.8 km/h)

Direction of Movement

Approached by vehicles, Following by vehicles, Overtaking vehicles

Detection Range

-6.5 ft (-2 m) ~ 82ft (25m)

Operating Voltage

9~18V

Waterproof

Working Current

Working Temperature

400mA

-40°F ~ 185°F (-40℃ 85℃)～

Radar sensor: IPX6/IPX7

Other items such as cables: NOT waterproof

FUSE rating value 2 A

Speed Restriction

The system will activate the sensors once the vehicle reaches a speed

above 18mph(29km/h).

English

-16-

NO.

Issues

Reasons

Solutions

1

Incorrect connection or pins

not making contact

LED light is broken Replace LED light

2

Make sure the LED indicator with

RED color is on driver side and

YELLOW is on the passenger side,

also the sensor with

RED color is on

driver side YELLOW is on the

passenger side

Make sure the signal wires are

connecting correctly

3

4

5

Troubleshooting

LED light does not

work

Check the

sure connection is correct

harness and make

Opposite LED

indicator

Microwave sensor or LED

indicators are plugged in

to the opposite connector

Speaker does not work

Wrong connection or pins

not making contact

Check the harness and make

sure connection is correct

Defective Speaker

Replace Speaker

Sensor or GPS

does not work

Sensor or GPS Antenna module

is covered by the metal

bumper or other metal

Find the best location where the

sensor or GPS Antenna cannot be

blocked by any metal

Unit does not work

Blind spot system does not

trigger the sensor if the speed

is less than 18 mph (29 km/h)

Keep the speed of your vehicle

higher than 18 mph (29 km/h)

6

7

FUSE is blown

Over current / Power surge Exchange FUSE (2 A)

Blind area object

detection not

consistent or unstable

Not Installed correct location

Find the correct location to install

Find the location where the radar

sensing area is not blocked by

objects(s)

Installed with wrong angle

(pointing upward)

Installed at a location with

object in front

English

Manuel d'instructions

et guide d'installation

Important (numéro de série)

Le numéro de série se trouve au bas de l'unité principale. Pour votre propre sécurité et

commodité, assurez-vous d'enregistrer le numéro.

SDA-BS900

DÉTECTION DES ANGLES MORTS / SYSTÈME

D'ASSISTANCE AU CHANGEMENT DE VOIE

Français

Précaution..............................................................19

Informations aux clients............................................................19

Informations importantes sur la sécurité................................20

Service après-vente ...................................................................21

Garantie limitée de trois ans.....................................................21

Visitez notre site Web ................................................................21

Conditions d'alerte................................................22

Indicateurs du système..........................................22

Liste des Articles ....................................................24

Schéma d'installation ............................................25

Schéma de raccordement ......................................26

Guide d'installation ...............................................27

Étape 1: Installation des têtes de capteur radar.....................28

Étape 2: Connexion des informations de clignotants ............30

Étape 3: Installation des témoins DEL......................................30

Étape 4: Installation du haut-parleur ......................................31

Étape 5: Installation de l'antenne GPS ....................................31

Étape 6: Installation du fillage..................................................31

Spécifications techniques .....................................32

Dépannage .............................................................33

Table des matières

Merci d'avoir acheté ce produit Pioneer.

Veuillez bien lire ces instructions afin de faire fonctionner votre

appareil correctement. Suite à la lecture de ces instructions,

conservez ce document dans un endroit sûr pour références

ultérieures.

-18-

Français

Précaution

Informations aux clients

FCC ID:

IC: 25782-SDABS900

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme à la section

15 des normes FCC et CNR d'innovation, sciences et développement économique Canada applicables

aux appareils radio exempts de licence. L’utilisation est autorisée sous les deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

- L'antenne ne peut pas être enlevée (ou remplacée) par l'utilisateur.

- Cet appareil est conforme aux limites d’exposition aux rayonnements énoncées pour un

environnement non contrôlé et respecte les règles directrices en radioélectriques (RF) de la FCC

concernant l'exposition aux fréquences radioélectriques (RF) CNR-102 de l’ISDE. Cet appareil émet

une onde-radio (RF) très faible qui est considérée conforme et sans évaluation requise de l’exposition

maximale. Cependant, cet appareil doit être installé et utilisé en gardant une distance de 20 cm ou

plus entre le dispositif rayonnant et le corps humain.

IYASDA-BS900

-19-

CAN ICES-3 B/NMB-3 B

Informations à l'utilisateur

- Les modifications ou modifications effectuées sans autorisation appropriée peuvent invalider tout

droit d'utiliser cet appareil.

NOTE: Cet appareil a été testé et s'est avéré conforme aux limites d'un appareil numérique de classe B,

conformément à la section 15 de la règlementation FCC. Ces limites sont conçues pour offrir une

protection raisonnable contre les interférences nocives à l’intérieur d’une installation résidentielle.

Cet appareil génère, utilise et peut émettre de l'énergie par radiofréquence. Si ce dernier n'est pas

installé et utilisé conformément aux instructions, il pourra causer des interférences nocives aux

communications radio. Toutefois, rien ne garantit l’exemption d’interférences dans une installation

particulière. Si cet appareil cause de tel interférences à la réception radio ou télé, confirmé par la

désactivation de l’appareil, l'utilisateur est encouragé à essayer de corriger la situation via une ou

plusieurs de ces actions:

l'utilisateur est encouragé à essayer de corriger l’interférence par une ou plusieurs de ces mesures;

- Réorienter ou déplacer l'antenne réceptrice.

- Augmenter la distance entre l’appareil et le récepteur.

- Alimenter l’appareil via une source ou circuit différent de celui auquel l’appareil interfère.

- Consulter le marchand ou un technicien expérimenté en radio/télévision pour obtenir de l'aide.

DECLARATION DE CONFORMITE DE LA FCC « FEDERAL COMMUNICATIONS COMMISSION »

Nom du produit: DÉTECTION DES ANGLES MORTS / SYSTÈME D'ASSISTANCE AU

CHANGEMENT DE VOIE

Numéro de modèle: SDA-BS900

Nom du parti responsable: PIONEER ELECTRONICS (USA) INC.

DIVISION AU SUPPORT ET SERVICES

Adresse: 2050 W. 190TH STREET, SUITE 100, TORRANCE, CA 90504, U.S.A.

Téléphone: 1-800-421-1404

URL: http://www.pioneerelectronics.com

Français

・Conditions particulières des véhicules à considérer

Pendant le démarrage et l'initialisation de l’appareil, ce dernier peut prendre jusqu'à 2 minutes pour

établir une connexion GPS. Si le véhicule est conduit avant qu'une connexion GPS ne soit établie ou si

la connexion GPS est interrompue (à l'intérieur d'un tunnel, d'une structure de stationnement, etc.),

le système peut ne pas fonctionner correctement, produisant des avertissements incorrects ou faux

ou ne pas générer d'avertissement. Une fois que la connexion GPS est établie ou rétablie, les deux

témoins DEL clignotent deux fois pour indiquer que l’appareil est prêt à être utilisé.

Ce système peut être utilisé sur n'importe quel véhicule, à l’exception des véhicules équipés de

pare-chocs métalliques, c'est-à-dire les camions. Lors du montage des capteurs, assurez-vous que les

capteurs ne sont pas obstrués par des objets métalliques pouvant bloquer ou interférer avec le

fonctionnement du système.

Les éléments suivants peuvent compromettre l'efficacité du système:

・Angle d'installation incorrect.

・Véhicules avec des obstructions métalliques devant la plaque d'immatriculation.

・Supports de vélo arrière ou équipement pour personnes handicapées.

・Emplacement incorrect du capteur sur le véhicule, exemple le centre du pare-chocs du véhicule.

・Situation indétectable

・Votre véhicule se déplace plus lentement que de vitesse de détection préréglé, tel que circuler

dans une congestion.

・Lorsque votre véhicule est en marche arrière et que la vitesse entre votre véhicule et les objets

environnants est inférieure à 5 mph (8 km/h).

・Si un véhicule approche ou dépasse votre véhicule et que la vitesse entre votre véhicule et ce

véhicule est supérieure à 37 mph (60 km/h). Par exemple, si vous roulez à une vitesse de

41mph (66 km/h), l’appareil ne peut détecter les véhicules s'approchant par l’arrière si leur vitesse

est supérieure à 78 mph (126 km/h).

・Situations pouvant affecter la précision de détection de l’appareil

・Des objets métalliques sont dans la trajectoire immédiate du signal de détection.

・La météo tel qu’une forte pluie ou neige, des conditions routières avec verglas pouvant entraîner

des variations de sensibilité.

・Routes de gravier, pouvant causer des interférences dues à la poussière et projection de pierres.

ATTENTION

Informations importantes sur la sécurité

CET APPAREIL D’AIDE À LA CONDUITE A POUR FONCTION DE NOTIFIER LA

PRÉSENCE D'OBSTACLES DANS LES ANGLES MORTS DU VÉHICULE.

Il NE PEUT DÉTECTER TOUS LES DANGERS ET OBJETS ET N’EST PAS

UN SUBSTITUT POUR VOTRE JUGEMENT ET ATTENTION.

AVANT TOUTE MANOEUVRE, VÉRIFIEZ VISUELLEMENT LES DEUX

CÔTÉS DU VÉHICULE POUR PLUS DE SÉCURITÉ.

AVERTISSEMENT

-20-

AVERTISSEMENT

・Vérifiez l'installation du capteur avant la conduite.

- Les vis sont-elles en place?

- L'appareil est-il fixé solidement?

- Si l'unité se détache lors de la conduite, elle pourrait caser un accident.

Français

La page charge ...

Pioneer SDA-BS900 Le manuel du propriétaire

Pioneer SDA-BS900 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents