Amazon L5B83H Guide de démarrage rapide

Amazon
Marque
Amazon
Modèle
L5B83H
Taper
Guide de démarrage rapide
User Guide
Quick Start Guide
WHAT’S IN THE BOX
• Wireless Remote Model L5B83H
• 2xAAA Batteries
Buttons:
Power, Voice Search, Navigation, Select, Menu, Back, Home, Rewind, Play/Pause, Fast Forward
Power On Device
- Insert batteries and install compartment cover
- Pair Device to host: Choose the applicable pairing instructions from the options below:
A. This is a replacement remote:
1. Restart your Fire TV/TV Stick by unplugging the power cable from your power outlet than
plugins it back in. After the TV home screen displays, your remote is ready for pairing.
2. Press and hold the Home button on the new remote for at least 10 seconds. Your new
remote should automatically pair with our fire TV/TV stick. You will see an on-screen
message when it has successfully paired.
B. This is an additional remote:
1. On your new remote, press and hold the Home button for 120 seconds to enter
discoverable mode.
2. You must use your existing remote for the following steps. Press the Home button.
3. Navigate to the Settings location at the top of the screen. Select Controllers and Bluetooth
Devices > Amazon Fire TV Remotes > Add New Remote. Your Amazon Fire TV will search for
discoverable remotes, and display them in a list.
4. Select the new remote, named Amazon fire TV remote. You will see and on-screen message
when it has been successfully paired.
Use your Voice Search
- Hold down voice search button and speak
IMPORTANT PRODUCT INFORMATION
For safety, compliance, recycling, and other important information regarding your Device, please refer
to the Legal & Compliance section in the User Manual.
Product Information
Safety and Compliance Information
Using Your Device around Other Electronic Devices
The Device, uses, and can radiate radio frequency (RF) energy and, if not used in accordance with its
instructions, may cause interference to radio communications and electronic equipment. External RF
signals may affect improperly installed or inadequately shielded electronic operating systems,
entertainment systems, and personal medical devices.
While most modern electronic equipment is shielded from external RF signals, if in doubt, check with
the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with
your physician or the manufacturer to determine if they are adequately shielded from external RF
signals.
There are some places where RF signals could constitute a hazard, such as health care facilities, and
construction sites. If you are not sure, look around for signs indicating that two-way radios or mobile
phones should be turned off.
FCC Compliance Information
Radio Frequency Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications that are not expressly approved by the party responsible for compliance could
make the device no longer comply with the FCC Rules.
Information on your device is on file with the FCC and can be found by inputting your device’s FCC ID,
which can be found on the back of Device, into the FCC ID Search form available at
transition.fcc.gov/oet/ea/fccid.
Information Regarding Exposure to Radio Frequency Energy
The output power of the radio technology used in the Device is below the radio frequency exposure
limits set by the FCC. Nevertheless, it is advised to use the Device in such a manner that minimizes the
potential for human contact during normal operations.
Canadian Compliance Information
This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-3(B)/ NMB-3(B)
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the
following two conditions:
1. this device may not cause interference; and
2. this device must accept any interference, including interference that may cause undesired operation
of the device.
This device is compliant with general population/uncontrolled RF exposure limits in IC RSS-102.
This device is designed and manufactured not to exceed the emission limits for exposure to radio
frequency (RF) energy set by the Innovation, Science and Economic Development Canada for an
uncontrolled environment.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. CAN ICES-3(B)/
NMB-3(B)
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Cet appareil est conforme aux normes CNR exemptes de licence d'Industrie Canada. Le fonctionnement
est soumis aux deux conditions suivantes :
1. cet appareil ne doit pas provoquer d'interférences et
2. cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l'appareil.
Cet appareil est conciliant avec les limites d'exposition de RF population/non contenu générales dans IC
RSS-102.
Product Specifications
Wireless Remote
Model #: L5B83H
Power: 2xAAA Batteries
Connectivity — BLE5.0
Operating temperature — 0 °C to 35 °C
  • Page 1 1
  • Page 2 2
  • Page 3 3

Amazon L5B83H Guide de démarrage rapide

Amazon
Marque
Amazon
Modèle
L5B83H
Taper
Guide de démarrage rapide
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents