Simplicity 7800500 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur

Ce manuel convient également à

Safety Instructions & Operator's Manual for
NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for
further details.
Manual No. 7104202 (Rev. ‘-’ 11/30/2009)
EUROPEAN
REAR ENGINE RIDING MOWER
SERIES 23
Models
E2512523BVE (7800499)
E2812523BVE (7800500)
E2813523BVE (7800501)
E331523KVE (7800502)
Not for
Reproduction
Thank You for purchasing this quality-built Snapper product. We’re pleased that you placed your
confidence in the Snapper brand. When operated and maintained according to the instructions in this
manual, your Snapper product will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with the
machine and how to avoid them. This machine is designed and intended only for finish cutting of
established lawns and is not intended for any other purpose. It is important that you read and understand
these instructions thoroughly before attempting to start or operate this equipment. Save these
instructions for future reference.
PRODUCT REGISTRATION
IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS
(Complete the following information on your Snapper purchase)
Date of Purchase__________________________________________________________________
Retailer_________________________________________________________________________
Retailer's Phone Number___________________________________________________________
Equipment
Model Number______________________________________________________________
Serial Number ______________________________________________________________
Engine
Model_________________________Type__________________Trim___________________
Briggs & Stratton Yard Power Products Group
Copyright © 2009, Briggs & Stratton Corporation
Milwaukee, WI, USA. All Rights Reserved.
SNAPPER is a trademark of
Briggs & Stratton Power Products Group, LLC
Jefferson, WI, USA.
Not for
Reproduction
3
Table of Contents
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Operator Seat Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Engaging Mower Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Engaging Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Stopping Engine, Wheel Drive, Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Setting Park Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Reverse Lockout Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Removing the Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Engine Adjustments and Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Mower Deck and Component Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Rear Engine Rider Drive Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Mower Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Mower Drive Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Snapper Rear Engine Rider Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Maintenance/Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Not for
Reproduction
www.snapper.com4
! !
WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects
that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in
serious injury or death to the operator or other persons. The owner of the machine must understand these
instructions and must allow only persons who understand these instructions to operate machine. Each
person operating the machine must be of sound mind and body and must not be under the influence of any
substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your
machine which your dealer cannot answer to your satisfaction, call or write the Customer Service
Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).
Protection for Children
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. Children who have been
given rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over by the
machine. Never assume that children will remain where you
last saw them.
1. KEEP children out of the mowing area and under the
watchful care of a responsible adult other than the operator.
2. DO NOT allow children in yard when machine is operated
(even with the blade OFF).
3. DO NOT allow children or others to ride on machine,
attachments or towed equipment (even with the blades
OFF). They may fall and be seriously injured.
4. DO NOT allow pre-teenage children to operate machine.
5. ALLOW only responsible adults & teenagers with mature
judgment under close adult supervision to operate machine.
6. DO NOT operate blades in reverse. STOP BLADES. LOOK
and SEE behind and down for children, pets and hazards
before and while backing.
7. USE EXTRA CARE when approaching blind corners,
shrubs, trees, or other objects that may obscure vision.
Protection against Tipovers
Slopes are a major factor related to loss-of-control and tip-
over accidents, which can result in severe injury or death.
All slopes require extra CAUTION. If you cannot back up the
slope or if you feel uneasy on the slope, DO NOT mow it.
Use extra care with grass catchers or other attachments;
these affect the handling and the stability of the machine.
1. DO NOT operate machine on slopes exceeding 10
degrees (18% grade).
2. Turn blades OFF when traveling uphill. Use a slow speed
and avoid sudden or sharp turns.
3. DO NOT operate machine back and forth across face of
slopes. Operate up and down. Practice on slopes with
blades off.
4. AVOID starting, stopping or turning on slopes. If machine
stops going uphill or tires lose traction, turn blades OFF and
back slowly straight down the slope.
5. STAY ALERT for holes and other hidden hazards. Tall
grass can hide obstacles. Keep away from ditches,
washouts, culverts, fences and protruding objects.
Protection against Tipovers
(Continued From Previous Column)
6. KEEP A SAFE DISTANCE (at least 3 feet) away from edge
of ditches and other drop offs. The machine could turn over
if an edge caves in.
7. Always begin forward motion slowly and with caution.
8. Use weights or a weighted load carrier in accordance
with instructions supplied with a grass catcher. DO NOT
operate machine on slopes exceeding 10 degrees (18%
grade) when equipped with grass catcher.
9. DO NOT put your foot on the ground to try to stabilize
the machine.
10. DO NOT operate machine on wet grass. Reduced trac-
tion could cause sliding.
11. Choose a low enough speed setting so that you will not
have to stop or shift on a slope. Tires may lose traction on
slopes even though the brakes are functioning properly.
12. DO NOT operate machine under any condition where
traction, steering or stability is doubtful.
13. Always keep the machine in gear when going down
slopes. DO NOT shift to neutral (or actuate hydro roll
release) and coast downhill.
Preparation
1. Read, understand, and follow instructions and warnings
in this manual and on the machine, engine and attach-
ments. Know the controls and the proper use of the
machine before starting.
2. Only mature, responsible persons shall operate the
machine and only after proper instruction.
3. Data indicates that operators age 60 and above, are
involved in a large percentage of mower-related injuries.
These operators should evaluate their ability to operate the
mower safely enough to protect themselves and others
from serious injury.
4. Handle fuel with extra care. Fuels are flammable and
vapors are explosive. Use only an approved fuel container.
DO NOT remove fuel cap or add fuel with engine running.
Add fuel outdoors only with engine stopped and cool. Clean
spilled fuel from machine. DO NOT smoke.
5. Practice operation of machine with BLADES OFF to learn
controls and develop skills.
6. Check the area to be mowed and remove all objects such
as toys, wire, rocks, limbs and other objects that could
cause injury if thrown by blade or interfere with mowing.
Important Operator Safety Instructions
Not for
Reproduction
5
! !
Protection against Tipovers
(Continued From Previous Column)
7. Keep people and pets out of mowing area. Immediately
STOP blades, STOP engine, and STOP machine if anyone
enters the area.
8. Check shields, deflectors, switches, blade controls and
other safety devices frequently for proper operation and
location.
9. Make sure all safety decals are clearly legible. Replace if
damaged.
10. Protect yourself when mowing and wear safety glasses,
a dust mask, long pants and substantial footwear.
11. Know how to STOP blades and engine quickly in prepa-
ration for emergencies.
12. Use extra care when loading or unloading the machine
into a trailer or truck.
13. Check grass catcher components frequently for signs of
wear or deterioration and replace as needed to prevent
injury from thrown objects going through weak or worn
spots.
Safe Handling of Gasoline
To avoid personal injury or property damage, use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive.
1. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
2. Use only an approved fuel container.
3. DO NOT remove fuel cap or add fuel with the engine run-
ning. Allow the engine to cool before refueling.
4. DO NOT refuel the machine indoors.
5. DO NOT store the machine or fuel container inside where
there is an open flame, spark or pilot light such as on a
water heater or other appliances.
6. DO NOT fill fuel containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place the contain-
ers on the ground away from the vehicle before filling.
7. Remove gas-powered equipment from the vehicle or
trailer and refuel it on the ground. If this is not possible,
then refuel equipment using a portable container, rather
than a gasoline dispenser nozzle.
8. DO NOT start gas powered equipment in enclosed vehi-
cles or trailers.
9. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. DO
NOT use a nozzle lock-open device
10. If fuel is spilled on clothing, change clothing immediate-
ly.
11. Never overfill a fuel tank. Replace fuel cap and tighten
securely.
Operation
1. Mount and dismount machine from left side. Keep clear
of discharge opening at all times.
2. Start engine from operator’s seat, if possible. Make sure
blades are OFF and parking brake is set.
3. DO NOT leave machine with engine running. STOP
engine, STOP blades, SET brake, and Remove key before
leaving operators position of any reason.
4. DO NOT operate machine unless properly seated with
feet on feet rests or pedal(s).
5. STOP BLADES and ENGINE and make sure blades have
stopped before removing grass catcher or unclogging
mower to prevent loss of fingers or hand.
6. Blades must be OFF except when cutting grass. Set
blades in highest position when mowing over rough
ground.
7. Keep hands and feet away from rotating blades under-
neath deck. DO NOT place foot on ground while BLADES
are ON or machine is in motion.
8. DO NOT operate machine without entire grass catcher or
guards in place and working. DO NOT point discharge at
people, passing cars, windows or doors.
9. Slow down before turning.
10. Watch out for traffic when near or crossing roadways.
11. STOP engine immediately after striking an obstruction.
Inspect machine and repair damage before resuming opera-
tion.
12. Operate machine only in daylight or with good artificial
light.
13. Move joystick (if equipped) SLOWLY to maintain control
during speed and directional changes.
14. Exercise CAUTION when pulling loads. Limit loads to
those you can safely control and attach loads to hitch plate
as specified with SNAPPER attachment instructions.
15. On slopes, the weight of the towed equipment may
cause loss of traction and loss of control. When towing,
travel slowly and allow extra distance to stop.
16. DO NOT operate engine in enclosed areas. Engine
exhaust gases contain carbon monoxide, a deadly poison.
17. DO NOT discharge material against a wall or obstruc-
tion. Material may ricochet back towards the operator.
18. Only use accessories approved by the manufacturer.
See manufacturer’s instructions for proper operation and
installation of accessories.
Important Operator Safety Instructions (Continued)
Not for
Reproduction
www.snapper.com6
! !
Towing
1. Tow only with a machine that has a hitch designed for
towing. DO NOT attach towed equipment except at the hitch
point.
2. Follow the manufacturer’s recommendation for weight
limits for towed equipment and towing on slopes.
3. DO NOT allow children or others on towed equipment.
4. On slopes, the weight of the towed equipment may cause
loss of traction and loss of control.
5. Travel slowly and allow extra distance to stop.
Maintenance
1. DO NOT store machine or fuel container inside where
fumes may reach an open flame, spark or pilot light such as
in a water heater, furnace, clothes dryer or other gas appli-
ance. Allow engine to cool before storing machine in an
enclosure. Store fuel container out of the reach of children
in a well ventilated, unoccupied building.
2. Keep engine free of grass, leaves or excess grease to
reduce fire hazard and engine overheating.
3. When draining fuel tank, drain fuel into an approved con-
tainer outdoors and away from open flame.
4. Check brakes frequently; adjust, repair or replace as
needed.
5. Keep all bolts, nuts and screws properly tight. Check that
all cotter pins are in proper position.
Maintenance
(Continued From Previous Column)
6. Always provide adequate ventilation when running
engine. Exhaust gases contain carbon monoxide, an odor-
less and deadly poison.
7. Disconnect negative (black) cable from battery before
performing maintenance or service. Cranking engine could
cause injury.
8. DO NOT work under machine without safety blocks.
9. Service engine and make adjustments only when engine
is stopped. Remove spark plug wire(s) from spark plug(s)
and secure wire(s) away from spark plug(s).
10. DO NOT change engine governor speed settings or
overspeed engine.
11. Lubricate machine at intervals specified in manual to
prevent controls from binding.
12. Mower blades are sharp and can cut. Wrap the blades
or wear heavy leather gloves and use CAUTION when han-
dling them.
13. DO NOT test for spark by grounding spark plug next to
spark plug hole; spark plug could ignite gas exiting engine.
14. Have machine serviced by an authorized SNAPPER
dealer at least once a year and have the dealer install any
new safety devices.
15. Maintain or replace safety and instruction labels as nec-
essary.
16. Use only genuine SNAPPER replacement parts to
assure that original standards are maintained.
Important Operator Safety Instructions (Continued)
Not for
Reproduction
7
Warning - 7100739
dB
Mfg. No. XXXXXXX
RIDING LAWN MOWER
S/N XXXXXXXXXX
SIMPLICITY MFG - SNAPPER
MCDONOUGH, GA 30253 USA
XX
2008
kg: XX
kW: X.XX
XXXX max
Serial Tag:
A. Manufacturing (Part) Number
B. Description/Model Number
C. Serial Number
D. Manufacturer Information
E. Sound Power
F. Unit Mass
G. Kilowatts
H. Max RPM’s
I. Year of Manufacture
J. European Certification
E
A
F
D
B
C
G
H
J
I
Decal Identification
Fuel Caution - 7101165
Deflector Caution - 7101167
Deck Warning - 7029784
Not for
Reproduction
www.snapper.com8
Safety Instructions - 7101166
Decal Identification (Continued)
Reverse Caution - 7074480
Battery Caution - 7101164
Battery Storage - 7101163
Height of Cut - 7046218
Clutch/Brake- 7028514
Not for
Reproduction
9
IMPORTANT
The figures and illustrations in this manual are provided
for reference only and may differ from your specific
model. Contact your Snapper dealer if you have questions.
Features and Controls
A. Steering Wheel
B. Engine Speed Control (hidden from view)
C. Ignition Switch
D. Clutch/Brake Pedal
E. Park Brake Latch
F. Blade Pedal
G. Blade Lever
H. Discharge Deflector
I. Override Control
J. Transmission Shift Lever
K. Fuel Tank
F
B
H
I
K
D
G
E
J
A
C
Features and Controls
Not for
Reproduction
www.snapper.com10
Pre-Start Check List
Make the following checks and perform the service required
before each start-up:
1. Check the tire pressure; add or release air as needed to
bring pressure to 12 PSI in front and 12 PSI in rear.
2. Check guards, deflectors and covers to make sure all are
in place and securely tightened.
3. Check engine oil and add oil as needed to bring level up
to the FULL mark (A, Figure 1). Refer to the engine
manual for oil specifications.
4. Adjust the seat (A, Figure 3) as needed to the most
comfortable position. Refer to the Section entitled
“OPERATOR’S SEAT ADJUSTMENT”.
5. Check the blade control to insure it works freely. If the
blade pedals are depressed, the blade lever can be
moved manually from “ON” to “OFF” to stop the blade.
6. Check the Reverse Lockout Mechanism. With the blade
pedals depressed, the shift lever must not go into
reverse.
7. Clean the exterior surfaces of the cutting deck and
engine of any accumulation of dirt, grass, oil, etc. Keep
the engine air intake screen and cooling fins clear at all
times.
8. Add fuel to the fuel tank after pushing the Rear Engine
Rider outside where fumes can dissipate. Make sure the
fuel filler cap (A, Figure 2) is tight, and the vent (B) is
open after refueling. Refer to the engine manual for fuel
specifications.
Operator Seat Adjustment
1. With the engine stopped, loosen the two adjusting
knobs (B, Figure 3) and move the seat to the desired
position. After adjustment, tighten the knobs securely.
NOTE: If the seat does not move after loosening the knobs, it
may be necessary to loosen the 5/16” patch lock screws or
hex nuts
(C)
located at the rear of the seat.
Figure 3: Operator seat adjustment
A
Figure 1: Engine oil ‘Full’ mark
A
Figure 2: Fuel filler cap
B
B
Operation
A
B
A
Not for
Reproduction
11
Starting and Operation
Engine (Electric Start)
IMPORTANT: When the ignition key is turned to “START”,
the engine will turn over, but will not start unless the
Clutch/Brake pedal is pressed all the way down, and the
Blade Lever is in the “OFF” position. The operator should be
in the seat.
Start the engine as follows:
1. Open the vent (B, Figure 2) on the fuel filler cap (A) by
turning counterclockwise.
IMPORTANT: Failure to open the vent on the fuel filler cap
can cause the engine to stall.
2. Move the transmission shift lever to the (N) Neutral
position. Refer to the section entitled “Wheel Drive”.
IMPORTANT: DO NOT start the engine with the transmission
shift lever in a drive position.
3. Make certain the Blade Lever (A, Figure 4) is in the
“OFF” position.
4. Press the Clutch/Brake Pedal (A, Figure 5) all the way
down and hold while starting the engine.
5. Move the engine speed control (A, Figure 6) to the
choke position (B) to start a cold engine.
6. Turn the ignition key (A, Figure 7) to the “START”
position until the engine starts.
NOTE: If after 5 seconds of cranking the engine does not
start, release the key, make sure the Clutch/Brake Pedal is
fully depressed, and attempt starting again after waiting for
approximately 20 seconds.
7. After the engine starts, move the engine speed control
to the “FAST” position and allow a brief warm-up until
engine runs smooth.
(Continued on Next Page)
Figure 4: Blade lever (in ‘Off’ position)
A
Operation (Continued)
WARNING
It is possible to start the engine with the transmission
shift lever in a drive position. Follow starting instructions
carefully.
!
!
Figure 5: Engaging the clutch/brake pedal
A
Figure 6: Engine speed control
A
B
Figure 7: Ignition key
A
Not for
Reproduction
www.snapper.com12
Starting and Operation (Continued)
Engine (Electric Start) (Continued)
8. Should the battery be too weak to start the engine, refer
to the Section entitled “Engine (Manual Start)” to
manually start the electric start engines.
9. On Model 2813523BVE, the engine is equipped with a
fuel shut-off solenoid. If the battery is dead, the engine
can be started with the recoil back-up starter if the
engine speed control is in the choke position (HOT
engine or COLD engine).
Engine (Manual Start)
IMPORTANT: When the key is turned to “ON”, and the recoil
handle is pulled, the engine will turn over, but will not start
unless the Clutch/Brake Pedal is pressed all the way down
with the Park Brake engaged, and the Blade Lever is in the
“Off” position.
Start the engine as follows:
1. Open the vent (B, Figure 2) on the fuel filler cap (A) by
turning counterclockwise.
IMPORTANT: Failure to open the vent on the fuel filler cap
can cause the engine to stall.
2. Move the transmission shift lever to the (N) Neutral
position. Refer to the section entitled “Wheel Drive”.
IMPORTANT: DO NOT start the engine with the transmission
shift lever in a drive position.
3. Make certain the Blade Lever (A, Figure 4) is in the
“OFF” position.
4. Press the Clutch/Brake Pedal (A, Figure 8) all the way
down, move the park brake latch (B) over, and release
the clutch/brake pedal to set the park brake.
5. Move the engine speed control (A, Figure 6) to the
choke position (B) to start a cold engine.
6. Turn the key (A, Figure 9) to the “ON” position.
7. Pull the starter rope, located on the engine recoil, with a
smooth, even motion until the engine starts.
NOTE: Always guide the starter rope back into the recoil
housing. Never allow rope to snap back.
After the engine starts, move the engine speed control
to the “FAST” position.
8. Allow a brief warm-up until the engine runs smooth.
Operation (Continued)
WARNING
It is possible to start the engine with the transmission
shift lever in a drive position. Follow starting instructions
carefully.
!
!
Figure 8: Setting the park brake
A
B
Figure 9: Key
A
Not for
Reproduction
13
Starting and Operation (Continued)
Mower Blade
1. With the engine running, move the engine speed control
to the “FAST” position.
2. Move the blade lever (A, Figure 10) forward to the “ON”
position, then depress the blade pedals (B) to hold the
blade lever in the “ON” position.
Wheel Drive
1. With the engine running, adjust the engine speed control
to the “FAST” position.
2. Depress the clutch/brake pedal (A, Figure 11).
3. Place the transmission shift lever (A, Figure 12) into
the first forward speed notch (B).
4. Release the clutch/brake pedal to begin forward motion.
5. During forward motion, the transmission shift lever
may be placed in any desired forward speed without
depressing the clutch/brake pedal.
NOTE: For best cutting results, move the transmission shift
lever into a slow forward speed and the engine speed control
to a fast position. This combination will allow the mower
blades to lift the grass while cutting smoothly and evenly.
Figure 10: Engaging the mower blade
A
Operation (Continued)
Figure 11: Engaging the clutch/brake pedal
A
Figure 12: Transmission shift lever
A
WARNING
Once blade is disengaged, it should come to a complete
stop in 3 seconds or less. If the blade continues to rotate
after 3 seconds, the blade brake must be adjusted. Refer to
Section “BLADE BRAKE ADJUSTMENT” for adjustment pro-
cedures or return machine to an authorized SNAPPER deal-
er for adjustment. DO NOT CONTINUE to operate machine
until blade brake is adjusted and functioning properly.
!
!
WARNING
DO NOT operate blades in reverse. STOP BLADES. LOOK
and SEE behind and down for children, pets and hazards
before and while backing.
!
!
B
B
Not for
Reproduction
www.snapper.com14
Stopping - Engine,
Wheel Drive, Blade
Engine
1. Stop the engine by turning the key (A, Figure 13) to the
“OFF” position.
Wheel Drive
1. Stop motion of the Rear Engine Rider by pushing the
clutch/brake pedal (A, Figure 14) all the way down to
apply the brake.
Mower Blade
1. Stop the mower blade by releasing the blade pedals (A,
Figure 15) or moving the blade lever (B) rearward to the
“OFF” position.
Operation (Continued)
WARNING
DO NOT leave the machine with the engine running. STOP
Blade. STOP engine. Shift to neutral and engage park brake.
Remove key.
!
!
WARNING
Once blade is disengaged, it should come to a complete
stop in 3 seconds or less. If the blade continues to rotate
after 3 seconds, the blade brake must be adjusted. Refer to
Section “BLADE BRAKE ADJUSTMENT” for adjustment pro-
cedures or return machine to an authorized SNAPPER deal-
er for adjustment. DO NOT CONTINUE to operate machine
until blade brake is adjusted and functioning properly.
!
!
Figure 13: Turning key to ‘Off’
A
Figure 15: Stopping the mower blade
B
A
Figure 14: Engaging the clutch/brake pedal
A
Not for
Reproduction
15
Stopping - Engine, Wheel Drive,
Blade (Continued)
Park Brake
1. To set the park brake, press the clutch/brake pedal (A,
Figure 16) all the way down, slide the park brake latch
(B) all the way in to the engaged position, and release
the clutch/brake pedal. A detent in the park brake latch
will keep the park brake engaged.
2. Release the park brake by pressing down firmly on the
clutch/brake pedal (A, Figure 17). The park brake latch
(B) is spring-loaded, and will slide back to the disen-
gaged position unassisted.
Cutting Height Adjustment
1. Adjust the cutting height by raising or lowering the deck
lift lever (A, Figure 18) into the desired height of cut
notch (B).
Operation (Continued)
WARNING
DO NOT park the machine on slopes.
!
!
Figure 17: Releasing the park brake
A
Figure 18: Cutting height adjustment
A
B
Figure 16: Setting the park brake
A
B
B
Not for
Reproduction
www.snapper.com16
Reverse Lockout Mechanism
Data indicates that tragic back-over accidents occur each
year. These accidents usually involve unsupervised children.
Many times these children have been given rides on the
machine and have been trained to view this potentially dan-
gerous piece of machinery as fun rather than being taught
how to avoid danger.
This riding mower has a Reverse Lockout Mechanism. This
mechanism prevents the mower from being shifted into
reverse with the blade running. To shift into reverse you
must first stop the blade by releasing the blade pedals and
then shift to reverse. It is our recommendation that this
mechanism remain functional and the operator of this equip-
ment develop the habit of never backing up with the blade
running. As the Safety Instructions Indicate, DO NOT oper-
ate blades in reverse. STOP BLADES, LOOK AND SEE
BEHIND AND DOWN for children, pets and hazards before
and while backing.
We realize that this could cause a change to your previous
mowing method but we encourage you to adjust to this new
system. Do not defeat the Reverse Lockout Mechanism.
If you operate your mower near roadways or use attach-
ments that require quicker shifting to reverse, there is an
override lever provided. This lever can be pushed and held
before starting the blade and will allow reverse operation
until the blade pedals are released, at which time the system
will return to its Reverse Lockout mode. This feature should
never be selected unless you are absolutely sure that no chil-
dren or others are present in the mowing area and that all
children are away and supervised by a responsible adult.
Reverse Lockout Mechanism Override
1. Stop the machine. Stop the blade.
2. Depress and hold the Override Lever.
3. Depress and hold the Blade Pedals. Release the
Override Lever.
4. Move the blade lever forward to “ON” position.
IMPORTANT: DO NOT use the Reverse Lockout Mechanism
Override as the normal operating mode. To return to the
Reverse Lockout Mechanism mode, release blade pedals to
turn blade off. The Override will reset to Reverse Lockout.
Check the Reverse Lockout Mechanism frequently for proper
function. With the blade pedals depressed, the shift lever
must not go into reverse. DO NOT operate machine if
Reverse Lockout Mechanism is not functioning properly.
Contact your local Snapper dealer for assistance.
Operation (Continued)
WARNING
LOOK and SEE behind and down for children, pets and
hazards before and while backing.
!
!
DANGER
LOOK and SEE behind and down for children, pets and
hazards before and while backing.
BLADES must be turned off before backing machine.
DO NOT allow children on machine (even with blades off)
or in yard when mowing.
!
!
Not for
Reproduction
17
Introduction
To retain the quality of the Rear Engine Rider, use genuine
SNAPPER replacement parts only. Contact a local SNAPPER
dealer for parts and service assistance. For the correct part
or information for a particular Rear Engine Riding Mower,
always mention the model and serial number. SNAPPER rec-
ommends returning the Rear Engine Rider to an authorized
SNAPPER dealer annually for inspection and addition of any
new devices, which might upgrade the safety of the Rear
Engine Rider. For the nearest SNAPPER dealer in your area,
check the yellow pages under the heading LAWN MOWERS.
For engine parts and service, look for the engine manufactur-
er’s dealers under the heading, ENGINES - gasoline.
Maintenance
Routine maintenance is important to the performance and
life of your Rear Engine Rider. Service performed properly
and at the recommended interval is essential. Refer to the
section entitled “MAINTENANCE SCHEDULE” in this manual
and in the Engine Owner’s Manual. Carefully complete all of
the recommended service procedures.
Change Engine Oil
1. Place bricks or wooden blocks under the front wheels to
lower the rear of the engine.
2. Loosen or remove the oil fill cap on the engine.
3. Place a 2 quart minimum capacity container under the
end of the oil drain (Figure 19).
4. Remove or open the oil drain plug (A or B, Figure 19),
depending upon the type of oil drain plug the engine is
equipped with.
5. After all the oil has drained, replace or close the drain
plug, and wipe up any oil that may have spilled.
Dispose of used oil properly.
6. Fill the engine crankcase with new oil. Refer to the
engine manual for oil specifications.
7. Change the oil filter on engines equipped with oil filters
at every oil change. Refer to the engine manual for serv-
ice instructions.
Service Engine Air Cleaner
The engine is equipped with a dual element air cleaner. Both
the foam pre-cleaner and cartridge require service. Refer to
the Engine Manual for recommended service procedures.
Check Mower Blade
1. Follow the WARNING statement found on this page.
2. Check the fuel level in the tank. If over 3/4 full, remove
the tank. Refer to the section entitled “REMOVING FUEL
TANK”. If 3/4 or less, proceed to the next step.
3. Carefully stand the Rear Engine Rider on the rear
bumper.
4. Check the torque of the blade mounting bolts (A, Figure
20). As necessary, torque to 30 to 40 ft. lbs.
5. Check the blade for sharpness, wear and damage. Refer
to the section entitled “BLADE WEAR LIMITS”.
6. Check the blade for straightness. Refer to the section
entitled “ADJUSTING MOWER BLADE”.
Maintenance
DANGER
Remove the battery if the Rear Engine Rider will be left
standing on the rear bumper for longer than 2 hours. Refer
to the section entitled “BATTERY REMOVAL”. DO NOT use
a cutting blade that shows signs of excessive wear or
damage on the Rear Engine Rider. Refer to the section
entitled “MOWER BLADE REPLACEMENT” for proper
blade inspection and service procedures.
!
!
WARNING
DO NOT attempt any adjustments, maintenance, service or
repairs with the engine running. STOP engine. STOP blade.
Engage parking brake. Remove key. Remove spark plug
wire from spark plug and secure away from plug. Engine
and components are HOT. Avoid serious burns, allow all
parts to cool before working on machine. Fuel Filler Cap
and vent must be closed securely to prevent fuel spillage.
!
!
Figure 20: Checking blade bolt torque
Figure 19: Oil drain plugs
A
B
A
Not for
Reproduction
www.snapper.com18
Check the Blade Drive Belt
The blade drive consists of a single belt from the engine to
the deck. Inspect for signs of deterioration and proper ten-
sion.
1. Lower the deck to the lowest setting.
2. Remove the four self-tapping screws (A, Figure 21),
two on each side of mower drive belt cover (B).
3. Slide the cover back and rotate out on the left side of
the mower deck.
4. Raise the deck to the 3rd height of cut position (middle
notch). With the engine “OFF”, move the blade lever
back to the “ON” position and depress the blade pedals.
5. 28” and 30” Decks *: Measure the belt spacing at the
idler pulley (A, Figure 22). The belt spacing (B) should
be 1-1/4” but no less than 1”. If the measurement is
less than 1”, the belt tension should be adjusted. Refer
to the section entitled “BLADE DRIVE BELT ADJUST-
MENT”.
* IMPORTANT: The blade drive belt on 33” decks does not
require tension adjustment. If the belt becomes worn or
slack it must be replaced. Refer to the section entitled
“BLADE DRIVE BELT REPLACEMENT”.
Blade Brake
1. Check the blade brake for proper function. The blade
should stop rotating in 3 seconds or less after moving
the blade control lever to the “OFF” position or after
releasing the blade pedals.
2. If the blade continues to rotate longer than 3 seconds
do not operate the machine. Refer to the section entitled
“BLADE BRAKE ADJUSTMENT”, or contact your
SNAPPER dealer for assistance.
Service Brake / Park Brake
1. Check the machine brake for proper function:
Engage the park brake, and push the machine. The
rear tires should skid.
Drive the machine forward and apply the brake. The
machine should come to a complete stop in less
than 5 ft.
2. If the brakes are not functioning properly, brake adjust-
ment must be completed before operating the machine.
Refer to the section entitled “SERVICE BRAKE – PARK
BRAKE ADJUSTMENT”.
Maintenance (Continued)
WARNING
Blades must stop rotating in 3 seconds or less after the
blade has been turned off. DO NOT operate machine until
blade brake has been adjusted and functioning properly.
!
!
WARNING
DO NOT attempt any adjustments, maintenance, service or
repairs with the engine running. STOP engine. STOP blade.
Engage parking brake. Remove key. Remove spark plug
wire from spark plug and secure away from plug. Engine
and components are HOT. Avoid serious burns, allow all
parts to cool before working on machine. Fuel Filler Cap
and vent must be closed securely to prevent fuel spillage.
!
!
Figure 21: Removing the drive belt cover
B
A
Figure 22: Measuring the belt spacing
A
B
WARNING
The following procedure requires the engine and blades to
be operated. Exercise extreme caution. Clear area of loose
parts & tools first. Only operate blades when seated in the
operator’s seat.
!
!
Not for
Reproduction
19
Safety Interlock System Checks
Perform the following interlock system checks periodically
during the operating season. Contact your authorized
Snapper dealer if you have questions.
Engine must not
start if:
1. The Clutch/Brake Pedal is not fully depressed OR,
2. The Blade Control is in the “ON” (blades engaged) posi-
tion.
Engine should
start if:
1. The Blade Control is in the “OFF” (blades disengaged)
position AND,
2. The Clutch/Brake Pedal is fully depressed.
Engine and blades must stop
if:
1. The operator rises off of seat with Blade Control in “ON”
(blades engaged) position OR,
2. The operator rises off of seat with Clutch/Brake Pedal
not fully depressed.
Reverse Lockout Mechanism
Check the function of the Reverse Lockout Mechanism with
the engine off.
1. Depress and hold the blade pedals.
2. Depress and hold the clutch/brake pedal.
3. With Steps 1 and 2 performed, the shift lever must not
go into reverse.
Lubrication – Grease Fittings
The following components on the Rear Engine Rider are
equipped with grease fittings and require periodic lubrica-
tion. Apply General Purpose grease (NLGI No.2) with a
grease gun.
1. Front Wheel Bearings. Refer to the section entitled
“FRONT WHEEL BEARINGS – LUBRICATION”.
2. Rear Axle Bearing. Refer to the section entitled “REAR
AXLE BEARING – LUBRICATION”.
3. Mower Blade Spindle. Refer to the section entitled
“MOWER BLADE SPINDLE – LUBRICATION”.
4. Shift Lever. Refer to the section entitled “SHIFT LEVER –
LUBRICATION”.
Check Engine
1. Change the engine oil. Refer to the section entitled
“CHANGE ENGINE OIL”. Refer to the engine manual for
oil specifications.
2. Change the air filter:
• Pull up and rotate the air cleaner latch (A, Figure
23) to remove the air cleaner cover (B).
IMPORTANT: When the cover is removed, you are viewing
the carburetor side of the air filter, which will appear clean.
Remove the filter and pre-cleaner for inspection.
• Remove the air cleaner (C).
• Remove and clean the engine air pre-cleaner
(located behind the air cleaner). Refer to the engine
manual for cleaning and service instructions.
• Install the pre-cleaner and replace the air cleaner
per the engine manual.
• Reinstall the air cleaner cover. Engage the latch
over the cover and rotate and push down to lock.
IMPORTANT: The tabs (D) on the air cleaner cover must be
completely inserted into the corresponding slots in the
engine cover, or the compartment will not be completely
sealed to prevent debris from entering into the carburetor.
Maintenance (Continued)
WARNING
DO NOT operate machine if Reverse Lockout Mechanism is
not functioning properly. Contact your SNAPPER dealer
immediately for assistance.
!
!
Figure 23: Opening the engine air cleaner cover
B
A
WARNING
DO NOT operate machine if any safety interlock or safety
device is not in place and functioning properly. DO NOT
attempt to defeat, modify or remove any safety device.
!
!
(Briggs engine shown)
D
C
Not for
Reproduction
www.snapper.com20
Battery Fluid Level
1. Remove the battery. Refer to the section entitled
“BATTERY REMOVAL”.
2. Remove the battery caps. Check the fluid level.
3. Add water only to bring fluid to proper level. DO NOT
OVERFILL.
4. Reinstall the battery. Refer to the section entitled
“BATTERY INSTALLATION”.
Mower Deck Levelness
Check the mower deck for proper level. Adjust as required.
Refer to the section entitled “MOWER DECK ADJUSTMENT –
LEVELNESS”.
Clean Mower Deck
1. Follow the WARNING statement found on this page.
2. Check the fuel level in the tank. If over 3/4 full, remove
the tank. Refer to the section entitled “REMOVING FUEL
TANK”. If 3/4 or less, proceed to the next step.
3. Carefully stand the Rear Engine Rider on the rear
bumper.
4. Clean the underside of the mower deck, removing all
accumulation of grass clippings and debris.
5. Clean the top of the deck, removing all grass clippings
and debris.
Mower Blade Spindle - Lubrication
1. Follow the WARNING statement found on this page.
2. Check the fuel level in tank. If over 3/4 full, remove the
tank. Refer to the section entitled “FUEL TANK
REMOVAL”. If 3/4 or less, proceed to the next step.
3. Carefully stand the Rear Engine Rider on the rear
bumper.
4. Lubricate the spindle grease fitting (A, Figure 24) with
three shots of general purpose grease from a grease
gun.
IMPORTANT: If the Rear Engine Rider will be on its rear
bumper for longer than two hours, remove the battery. Refer
to the section entitled “BATTERY REMOVAL”.
Mower Deck Linkage - Lubrication
Lubricate all mower deck linkage pivot points with a light
coat of motor oil.
Front Wheel Bearing - Lubrication
Lubricate the front wheel grease fittings (A, Figure 25) with
five shots of general purpose grease, from a grease gun.
Shift Lever - Lubrication
Lubricate the shift lever grease fitting (A, Figure 26) with
two shots of general purpose grease from a grease gun.
Maintenance (Continued)
WARNING
DO NOT attempt any adjustments, maintenance, service or
repairs with the engine running. STOP engine. STOP blade.
Engage parking brake. Remove key. Remove spark plug
wire from spark plug and secure away from plug. Engine
and components are HOT. Avoid serious burns, allow all
parts to cool before working on machine. Fuel Filler Cap
and vent must be closed securely to prevent fuel spillage.
!
!
Figure 25: Front wheel grease fitting
A
Figure 24: Mower blade spindle grease fitting
A
Figure 26: Shift lever grease fitting
A
Not for
Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228

Simplicity 7800500 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Ce manuel convient également à