Simplicity MANUAL, OPS, EURO RER Manuel utilisateur

Safety Instructions & Operator's Manual for

NOTE: Specifications are correct at time of printing and are subject to change without notice.

* Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ for

further details.

Manual No. 7104202 (Rev. ‘-’ 11/30/2009)

EUROPEAN

REAR ENGINE RIDING MOWER

SERIES 23

Models

E2512523BVE (7800499)

E2812523BVE (7800500)

E2813523BVE (7800501)

E331523KVE (7800502)

Not for

Reproduction

Thank You for purchasing this quality-built Snapper product. We’re pleased that you placed your

confidence in the Snapper brand. When operated and maintained according to the instructions in this

manual, your Snapper product will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with the

machine and how to avoid them. This machine is designed and intended only for finish cutting of

established lawns and is not intended for any other purpose. It is important that you read and understand

these instructions thoroughly before attempting to start or operate this equipment. Save these

instructions for future reference.

PRODUCT REGISTRATION

IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS

(Complete the following information on your Snapper purchase)

Date of Purchase__________________________________________________________________

Retailer_________________________________________________________________________

Retailer's Phone Number___________________________________________________________

Equipment

Model Number______________________________________________________________

Serial Number ______________________________________________________________

Engine

Model_________________________Type__________________Trim___________________

Briggs & Stratton Yard Power Products Group

SNAPPER is a trademark of

Briggs & Stratton Power Products Group, LLC

Jefferson, WI, USA.

Not for

Reproduction

3

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Operator Seat Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Starting Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Engaging Mower Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Engaging Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Stopping Engine, Wheel Drive, Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Setting Park Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Reverse Lockout Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Removing the Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Engine Adjustments and Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Mower Deck and Component Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Rear Engine Rider Drive Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Mower Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Mower Drive Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Snapper Rear Engine Rider Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Maintenance/Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Not for

Reproduction

www.snapper.com4

! !

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects

that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in

serious injury or death to the operator or other persons. The owner of the machine must understand these

instructions and must allow only persons who understand these instructions to operate machine. Each

person operating the machine must be of sound mind and body and must not be under the influence of any

substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your

machine which your dealer cannot answer to your satisfaction, call or write the Customer Service

Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).

Protection for Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Children who have been

given rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over by the

machine. Never assume that children will remain where you

last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the operator.

2. DO NOT allow children in yard when machine is operated

(even with the blade OFF).

3. DO NOT allow children or others to ride on machine,

attachments or towed equipment (even with the blades

OFF). They may fall and be seriously injured.

4. DO NOT allow pre-teenage children to operate machine.

5. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate machine.

6. DO NOT operate blades in reverse. STOP BLADES. LOOK

and SEE behind and down for children, pets and hazards

before and while backing.

7. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

Protection against Tipovers

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

All slopes require extra CAUTION. If you cannot back up the

slope or if you feel uneasy on the slope, DO NOT mow it.

Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

1. DO NOT operate machine on slopes exceeding 10

degrees (18% grade).

2. Turn blades OFF when traveling uphill. Use a slow speed

and avoid sudden or sharp turns.

3. DO NOT operate machine back and forth across face of

slopes. Operate up and down. Practice on slopes with

blades off.

4. AVOID starting, stopping or turning on slopes. If machine

stops going uphill or tires lose traction, turn blades OFF and

back slowly straight down the slope.

5. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches,

washouts, culverts, fences and protruding objects.

Protection against Tipovers

(Continued From Previous Column)

6. KEEP A SAFE DISTANCE (at least 3 feet) away from edge

of ditches and other drop offs. The machine could turn over

if an edge caves in.

7. Always begin forward motion slowly and with caution.

8. Use weights or a weighted load carrier in accordance

with instructions supplied with a grass catcher. DO NOT

operate machine on slopes exceeding 10 degrees (18%

grade) when equipped with grass catcher.

9. DO NOT put your foot on the ground to try to stabilize

the machine.

10. DO NOT operate machine on wet grass. Reduced trac-

tion could cause sliding.

11. Choose a low enough speed setting so that you will not

have to stop or shift on a slope. Tires may lose traction on

slopes even though the brakes are functioning properly.

12. DO NOT operate machine under any condition where

traction, steering or stability is doubtful.

13. Always keep the machine in gear when going down

slopes. DO NOT shift to neutral (or actuate hydro roll

release) and coast downhill.

Preparation

1. Read, understand, and follow instructions and warnings

in this manual and on the machine, engine and attach-

ments. Know the controls and the proper use of the

machine before starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate the

mower safely enough to protect themselves and others

from serious injury.

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel container.

DO NOT remove fuel cap or add fuel with engine running.

Add fuel outdoors only with engine stopped and cool. Clean

spilled fuel from machine. DO NOT smoke.

5. Practice operation of machine with BLADES OFF to learn

controls and develop skills.

6. Check the area to be mowed and remove all objects such

as toys, wire, rocks, limbs and other objects that could

cause injury if thrown by blade or interfere with mowing.

Important Operator Safety Instructions

Not for

Reproduction

5

! !

Protection against Tipovers

(Continued From Previous Column)

7. Keep people and pets out of mowing area. Immediately

STOP blades, STOP engine, and STOP machine if anyone

enters the area.

8. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

9. Make sure all safety decals are clearly legible. Replace if

damaged.

10. Protect yourself when mowing and wear safety glasses,

a dust mask, long pants and substantial footwear.

11. Know how to STOP blades and engine quickly in prepa-

ration for emergencies.

12. Use extra care when loading or unloading the machine

into a trailer or truck.

13. Check grass catcher components frequently for signs of

wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or worn

spots.

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine run-

ning. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where

there is an open flame, spark or pilot light such as on a

water heater or other appliances.

6. DO NOT fill fuel containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place the contain-

ers on the ground away from the vehicle before filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed vehi-

cles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. DO

NOT use a nozzle lock-open device

10. If fuel is spilled on clothing, change clothing immediate-

ly.

11. Never overfill a fuel tank. Replace fuel cap and tighten

securely.

Operation

1. Mount and dismount machine from left side. Keep clear

of discharge opening at all times.

2. Start engine from operator’s seat, if possible. Make sure

blades are OFF and parking brake is set.

3. DO NOT leave machine with engine running. STOP

engine, STOP blades, SET brake, and Remove key before

leaving operators position of any reason.

4. DO NOT operate machine unless properly seated with

feet on feet rests or pedal(s).

5. STOP BLADES and ENGINE and make sure blades have

stopped before removing grass catcher or unclogging

mower to prevent loss of fingers or hand.

6. Blades must be OFF except when cutting grass. Set

blades in highest position when mowing over rough

ground.

7. Keep hands and feet away from rotating blades under-

neath deck. DO NOT place foot on ground while BLADES

are ON or machine is in motion.

8. DO NOT operate machine without entire grass catcher or

guards in place and working. DO NOT point discharge at

people, passing cars, windows or doors.

9. Slow down before turning.

10. Watch out for traffic when near or crossing roadways.

11. STOP engine immediately after striking an obstruction.

Inspect machine and repair damage before resuming opera-

tion.

12. Operate machine only in daylight or with good artificial

light.

13. Move joystick (if equipped) SLOWLY to maintain control

during speed and directional changes.

14. Exercise CAUTION when pulling loads. Limit loads to

those you can safely control and attach loads to hitch plate

as specified with SNAPPER attachment instructions.

15. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control. When towing,

travel slowly and allow extra distance to stop.

16. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly poison.

17. DO NOT discharge material against a wall or obstruc-

tion. Material may ricochet back towards the operator.

18. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation and

installation of accessories.

Important Operator Safety Instructions (Continued)

Not for

Reproduction

www.snapper.com6

! !

Towing

1. Tow only with a machine that has a hitch designed for

towing. DO NOT attach towed equipment except at the hitch

point.

2. Follow the manufacturer’s recommendation for weight

limits for towed equipment and towing on slopes.

3. DO NOT allow children or others on towed equipment.

4. On slopes, the weight of the towed equipment may cause

loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

Maintenance

1. DO NOT store machine or fuel container inside where

fumes may reach an open flame, spark or pilot light such as

in a water heater, furnace, clothes dryer or other gas appli-

ance. Allow engine to cool before storing machine in an

enclosure. Store fuel container out of the reach of children

in a well ventilated, unoccupied building.

2. Keep engine free of grass, leaves or excess grease to

reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved con-

tainer outdoors and away from open flame.

4. Check brakes frequently; adjust, repair or replace as

needed.

5. Keep all bolts, nuts and screws properly tight. Check that

all cotter pins are in proper position.

Maintenance

(Continued From Previous Column)

6. Always provide adequate ventilation when running

engine. Exhaust gases contain carbon monoxide, an odor-

less and deadly poison.

7. Disconnect negative (black) cable from battery before

performing maintenance or service. Cranking engine could

cause injury.

8. DO NOT work under machine without safety blocks.

9. Service engine and make adjustments only when engine

is stopped. Remove spark plug wire(s) from spark plug(s)

and secure wire(s) away from spark plug(s).

10. DO NOT change engine governor speed settings or

overspeed engine.

11. Lubricate machine at intervals specified in manual to

prevent controls from binding.

12. Mower blades are sharp and can cut. Wrap the blades

or wear heavy leather gloves and use CAUTION when han-

dling them.

13. DO NOT test for spark by grounding spark plug next to

spark plug hole; spark plug could ignite gas exiting engine.

14. Have machine serviced by an authorized SNAPPER

dealer at least once a year and have the dealer install any

new safety devices.

15. Maintain or replace safety and instruction labels as nec-

essary.

16. Use only genuine SNAPPER replacement parts to

assure that original standards are maintained.

Important Operator Safety Instructions (Continued)

Not for

Reproduction

7

Warning - 7100739

dB

Mfg. No. XXXXXXX

RIDING LAWN MOWER

S/N XXXXXXXXXX

SIMPLICITY MFG - SNAPPER

MCDONOUGH, GA 30253 USA

XX

2008

kg: XX

kW: X.XX

XXXX max

Serial Tag:

A. Manufacturing (Part) Number

B. Description/Model Number

C. Serial Number

D. Manufacturer Information

E. Sound Power

F. Unit Mass

G. Kilowatts

H. Max RPM’s

I. Year of Manufacture

J. European Certification

E

A

F

D

B

C

G

H

J

I

Decal Identification

Fuel Caution - 7101165

Deflector Caution - 7101167

Deck Warning - 7029784

Not for

Reproduction

www.snapper.com8

Safety Instructions - 7101166

Decal Identification (Continued)

Reverse Caution - 7074480

Battery Caution - 7101164

Battery Storage - 7101163

Height of Cut - 7046218

Clutch/Brake- 7028514

Not for

Reproduction

9

IMPORTANT

The figures and illustrations in this manual are provided

for reference only and may differ from your specific

model. Contact your Snapper dealer if you have questions.

Features and Controls

A. Steering Wheel

B. Engine Speed Control (hidden from view)

C. Ignition Switch

D. Clutch/Brake Pedal

E. Park Brake Latch

F. Blade Pedal

G. Blade Lever

H. Discharge Deflector

I. Override Control

J. Transmission Shift Lever

K. Fuel Tank

F

B

H

I

K

D

G

E

J

A

C

Features and Controls

Not for

Reproduction

www.snapper.com10

Pre-Start Check List

Make the following checks and perform the service required

before each start-up:

1. Check the tire pressure; add or release air as needed to

bring pressure to 12 PSI in front and 12 PSI in rear.

2. Check guards, deflectors and covers to make sure all are

in place and securely tightened.

3. Check engine oil and add oil as needed to bring level up

to the FULL mark (A, Figure 1). Refer to the engine

manual for oil specifications.

4. Adjust the seat (A, Figure 3) as needed to the most

comfortable position. Refer to the Section entitled

“OPERATOR’S SEAT ADJUSTMENT”.

5. Check the blade control to insure it works freely. If the

blade pedals are depressed, the blade lever can be

moved manually from “ON” to “OFF” to stop the blade.

6. Check the Reverse Lockout Mechanism. With the blade

pedals depressed, the shift lever must not go into

reverse.

7. Clean the exterior surfaces of the cutting deck and

engine of any accumulation of dirt, grass, oil, etc. Keep

the engine air intake screen and cooling fins clear at all

times.

8. Add fuel to the fuel tank after pushing the Rear Engine

Rider outside where fumes can dissipate. Make sure the

fuel filler cap (A, Figure 2) is tight, and the vent (B) is

open after refueling. Refer to the engine manual for fuel

specifications.

Operator Seat Adjustment

1. With the engine stopped, loosen the two adjusting

knobs (B, Figure 3) and move the seat to the desired

position. After adjustment, tighten the knobs securely.

NOTE: If the seat does not move after loosening the knobs, it

may be necessary to loosen the 5/16” patch lock screws or

hex nuts

(C)

located at the rear of the seat.

Figure 3: Operator seat adjustment

A

Figure 1: Engine oil ‘Full’ mark

A

Figure 2: Fuel filler cap

B

Operation

A

B

A

Not for

Reproduction

11

Starting and Operation

Engine (Electric Start)

IMPORTANT: When the ignition key is turned to “START”,

the engine will turn over, but will not start unless the

Clutch/Brake pedal is pressed all the way down, and the

Blade Lever is in the “OFF” position. The operator should be

in the seat.

Start the engine as follows:

1. Open the vent (B, Figure 2) on the fuel filler cap (A) by

turning counterclockwise.

IMPORTANT: Failure to open the vent on the fuel filler cap

can cause the engine to stall.

2. Move the transmission shift lever to the (N) Neutral

position. Refer to the section entitled “Wheel Drive”.

IMPORTANT: DO NOT start the engine with the transmission

shift lever in a drive position.

3. Make certain the Blade Lever (A, Figure 4) is in the

“OFF” position.

4. Press the Clutch/Brake Pedal (A, Figure 5) all the way

down and hold while starting the engine.

5. Move the engine speed control (A, Figure 6) to the

choke position (B) to start a cold engine.

6. Turn the ignition key (A, Figure 7) to the “START”

position until the engine starts.

NOTE: If after 5 seconds of cranking the engine does not

start, release the key, make sure the Clutch/Brake Pedal is

fully depressed, and attempt starting again after waiting for

approximately 20 seconds.

7. After the engine starts, move the engine speed control

to the “FAST” position and allow a brief warm-up until

engine runs smooth.

(Continued on Next Page)

Figure 4: Blade lever (in ‘Off’ position)

A

Operation (Continued)

WARNING

It is possible to start the engine with the transmission

shift lever in a drive position. Follow starting instructions

carefully.

!

Figure 5: Engaging the clutch/brake pedal

A

Figure 6: Engine speed control

A

B

Figure 7: Ignition key

A

Not for

Reproduction

www.snapper.com12

Starting and Operation (Continued)

Engine (Electric Start) (Continued)

8. Should the battery be too weak to start the engine, refer

to the Section entitled “Engine (Manual Start)” to

manually start the electric start engines.

9. On Model 2813523BVE, the engine is equipped with a

fuel shut-off solenoid. If the battery is dead, the engine

can be started with the recoil back-up starter if the

engine speed control is in the choke position (HOT

engine or COLD engine).

Engine (Manual Start)

IMPORTANT: When the key is turned to “ON”, and the recoil

handle is pulled, the engine will turn over, but will not start

unless the Clutch/Brake Pedal is pressed all the way down

with the Park Brake engaged, and the Blade Lever is in the

“Off” position.

Start the engine as follows:

1. Open the vent (B, Figure 2) on the fuel filler cap (A) by

turning counterclockwise.

IMPORTANT: Failure to open the vent on the fuel filler cap

can cause the engine to stall.

2. Move the transmission shift lever to the (N) Neutral

position. Refer to the section entitled “Wheel Drive”.

IMPORTANT: DO NOT start the engine with the transmission

shift lever in a drive position.

3. Make certain the Blade Lever (A, Figure 4) is in the

“OFF” position.

4. Press the Clutch/Brake Pedal (A, Figure 8) all the way

down, move the park brake latch (B) over, and release

the clutch/brake pedal to set the park brake.

5. Move the engine speed control (A, Figure 6) to the

choke position (B) to start a cold engine.

6. Turn the key (A, Figure 9) to the “ON” position.

7. Pull the starter rope, located on the engine recoil, with a

smooth, even motion until the engine starts.

NOTE: Always guide the starter rope back into the recoil

housing. Never allow rope to snap back.

After the engine starts, move the engine speed control

to the “FAST” position.

8. Allow a brief warm-up until the engine runs smooth.

Operation (Continued)

WARNING

It is possible to start the engine with the transmission

shift lever in a drive position. Follow starting instructions

carefully.

!

Figure 8: Setting the park brake

A

B

Figure 9: Key

A

Not for

Reproduction

13

Starting and Operation (Continued)

Mower Blade

1. With the engine running, move the engine speed control

to the “FAST” position.

2. Move the blade lever (A, Figure 10) forward to the “ON”

position, then depress the blade pedals (B) to hold the

blade lever in the “ON” position.

Wheel Drive

1. With the engine running, adjust the engine speed control

to the “FAST” position.

2. Depress the clutch/brake pedal (A, Figure 11).

3. Place the transmission shift lever (A, Figure 12) into

the first forward speed notch (B).

4. Release the clutch/brake pedal to begin forward motion.

5. During forward motion, the transmission shift lever

may be placed in any desired forward speed without

depressing the clutch/brake pedal.

NOTE: For best cutting results, move the transmission shift

lever into a slow forward speed and the engine speed control

to a fast position. This combination will allow the mower

blades to lift the grass while cutting smoothly and evenly.

Figure 10: Engaging the mower blade

A

Operation (Continued)

Figure 11: Engaging the clutch/brake pedal

A

Figure 12: Transmission shift lever

A

WARNING

Once blade is disengaged, it should come to a complete

stop in 3 seconds or less. If the blade continues to rotate

after 3 seconds, the blade brake must be adjusted. Refer to

Section “BLADE BRAKE ADJUSTMENT” for adjustment pro-

cedures or return machine to an authorized SNAPPER deal-

er for adjustment. DO NOT CONTINUE to operate machine

until blade brake is adjusted and functioning properly.

!

WARNING

DO NOT operate blades in reverse. STOP BLADES. LOOK

and SEE behind and down for children, pets and hazards

before and while backing.

!

B

Not for

Reproduction

www.snapper.com14

Stopping - Engine,

Wheel Drive, Blade

Engine

1. Stop the engine by turning the key (A, Figure 13) to the

“OFF” position.

Wheel Drive

1. Stop motion of the Rear Engine Rider by pushing the

clutch/brake pedal (A, Figure 14) all the way down to

apply the brake.

Mower Blade

1. Stop the mower blade by releasing the blade pedals (A,

Figure 15) or moving the blade lever (B) rearward to the

“OFF” position.

Operation (Continued)

WARNING

DO NOT leave the machine with the engine running. STOP

Blade. STOP engine. Shift to neutral and engage park brake.

Remove key.

!

WARNING

Once blade is disengaged, it should come to a complete

stop in 3 seconds or less. If the blade continues to rotate

after 3 seconds, the blade brake must be adjusted. Refer to

Section “BLADE BRAKE ADJUSTMENT” for adjustment pro-

cedures or return machine to an authorized SNAPPER deal-

er for adjustment. DO NOT CONTINUE to operate machine

until blade brake is adjusted and functioning properly.

!

Figure 13: Turning key to ‘Off’

A

Figure 15: Stopping the mower blade

B

A

Figure 14: Engaging the clutch/brake pedal

A

Not for

Reproduction

15

Stopping - Engine, Wheel Drive,

Blade (Continued)

Park Brake

1. To set the park brake, press the clutch/brake pedal (A,

Figure 16) all the way down, slide the park brake latch

(B) all the way in to the engaged position, and release

the clutch/brake pedal. A detent in the park brake latch

will keep the park brake engaged.

2. Release the park brake by pressing down firmly on the

clutch/brake pedal (A, Figure 17). The park brake latch

(B) is spring-loaded, and will slide back to the disen-

gaged position unassisted.

Cutting Height Adjustment

1. Adjust the cutting height by raising or lowering the deck

lift lever (A, Figure 18) into the desired height of cut

notch (B).

Operation (Continued)

WARNING

DO NOT park the machine on slopes.

!

Figure 17: Releasing the park brake

A

Figure 18: Cutting height adjustment

A

B

Figure 16: Setting the park brake

A

B

Not for

Reproduction

www.snapper.com16

Reverse Lockout Mechanism

Data indicates that tragic back-over accidents occur each

year. These accidents usually involve unsupervised children.

Many times these children have been given rides on the

machine and have been trained to view this potentially dan-

gerous piece of machinery as fun rather than being taught

how to avoid danger.

This riding mower has a Reverse Lockout Mechanism. This

mechanism prevents the mower from being shifted into

reverse with the blade running. To shift into reverse you

must first stop the blade by releasing the blade pedals and

then shift to reverse. It is our recommendation that this

mechanism remain functional and the operator of this equip-

ment develop the habit of never backing up with the blade

running. As the Safety Instructions Indicate, DO NOT oper-

ate blades in reverse. STOP BLADES, LOOK AND SEE

BEHIND AND DOWN for children, pets and hazards before

and while backing.

We realize that this could cause a change to your previous

mowing method but we encourage you to adjust to this new

system. Do not defeat the Reverse Lockout Mechanism.

If you operate your mower near roadways or use attach-

ments that require quicker shifting to reverse, there is an

override lever provided. This lever can be pushed and held

before starting the blade and will allow reverse operation

until the blade pedals are released, at which time the system

will return to its Reverse Lockout mode. This feature should

never be selected unless you are absolutely sure that no chil-

dren or others are present in the mowing area and that all

children are away and supervised by a responsible adult.

Reverse Lockout Mechanism Override

1. Stop the machine. Stop the blade.

2. Depress and hold the Override Lever.

3. Depress and hold the Blade Pedals. Release the

Override Lever.

4. Move the blade lever forward to “ON” position.

IMPORTANT: DO NOT use the Reverse Lockout Mechanism

Override as the normal operating mode. To return to the

Reverse Lockout Mechanism mode, release blade pedals to

turn blade off. The Override will reset to Reverse Lockout.

Check the Reverse Lockout Mechanism frequently for proper

function. With the blade pedals depressed, the shift lever

must not go into reverse. DO NOT operate machine if

Reverse Lockout Mechanism is not functioning properly.

Contact your local Snapper dealer for assistance.

Operation (Continued)

WARNING

LOOK and SEE behind and down for children, pets and

hazards before and while backing.

!

DANGER

LOOK and SEE behind and down for children, pets and

hazards before and while backing.

BLADES must be turned off before backing machine.

DO NOT allow children on machine (even with blades off)

or in yard when mowing.

!

Not for

Reproduction

17

Introduction

To retain the quality of the Rear Engine Rider, use genuine

SNAPPER replacement parts only. Contact a local SNAPPER

dealer for parts and service assistance. For the correct part

or information for a particular Rear Engine Riding Mower,

always mention the model and serial number. SNAPPER rec-

ommends returning the Rear Engine Rider to an authorized

SNAPPER dealer annually for inspection and addition of any

new devices, which might upgrade the safety of the Rear

Engine Rider. For the nearest SNAPPER dealer in your area,

check the yellow pages under the heading LAWN MOWERS.

For engine parts and service, look for the engine manufactur-

er’s dealers under the heading, ENGINES - gasoline.

Maintenance

Routine maintenance is important to the performance and

life of your Rear Engine Rider. Service performed properly

and at the recommended interval is essential. Refer to the

section entitled “MAINTENANCE SCHEDULE” in this manual

and in the Engine Owner’s Manual. Carefully complete all of

the recommended service procedures.

Change Engine Oil

1. Place bricks or wooden blocks under the front wheels to

lower the rear of the engine.

2. Loosen or remove the oil fill cap on the engine.

3. Place a 2 quart minimum capacity container under the

end of the oil drain (Figure 19).

4. Remove or open the oil drain plug (A or B, Figure 19),

depending upon the type of oil drain plug the engine is

equipped with.

5. After all the oil has drained, replace or close the drain

plug, and wipe up any oil that may have spilled.

Dispose of used oil properly.

6. Fill the engine crankcase with new oil. Refer to the

engine manual for oil specifications.

7. Change the oil filter on engines equipped with oil filters

at every oil change. Refer to the engine manual for serv-

ice instructions.

Service Engine Air Cleaner

The engine is equipped with a dual element air cleaner. Both

the foam pre-cleaner and cartridge require service. Refer to

the Engine Manual for recommended service procedures.

Check Mower Blade

1. Follow the WARNING statement found on this page.

2. Check the fuel level in the tank. If over 3/4 full, remove

the tank. Refer to the section entitled “REMOVING FUEL

TANK”. If 3/4 or less, proceed to the next step.

3. Carefully stand the Rear Engine Rider on the rear

bumper.

4. Check the torque of the blade mounting bolts (A, Figure

20). As necessary, torque to 30 to 40 ft. lbs.

5. Check the blade for sharpness, wear and damage. Refer

to the section entitled “BLADE WEAR LIMITS”.

6. Check the blade for straightness. Refer to the section

entitled “ADJUSTING MOWER BLADE”.

Maintenance

DANGER

Remove the battery if the Rear Engine Rider will be left

standing on the rear bumper for longer than 2 hours. Refer

to the section entitled “BATTERY REMOVAL”. DO NOT use

a cutting blade that shows signs of excessive wear or

damage on the Rear Engine Rider. Refer to the section

entitled “MOWER BLADE REPLACEMENT” for proper

blade inspection and service procedures.

!

WARNING

DO NOT attempt any adjustments, maintenance, service or

repairs with the engine running. STOP engine. STOP blade.

Engage parking brake. Remove key. Remove spark plug

wire from spark plug and secure away from plug. Engine

and components are HOT. Avoid serious burns, allow all

parts to cool before working on machine. Fuel Filler Cap

and vent must be closed securely to prevent fuel spillage.

!

Figure 20: Checking blade bolt torque

Figure 19: Oil drain plugs

A

B

A

Not for

Reproduction

www.snapper.com18

Check the Blade Drive Belt

The blade drive consists of a single belt from the engine to

the deck. Inspect for signs of deterioration and proper ten-

sion.

1. Lower the deck to the lowest setting.

2. Remove the four self-tapping screws (A, Figure 21),

two on each side of mower drive belt cover (B).

3. Slide the cover back and rotate out on the left side of

the mower deck.

4. Raise the deck to the 3rd height of cut position (middle

notch). With the engine “OFF”, move the blade lever

back to the “ON” position and depress the blade pedals.

5. 28” and 30” Decks *: Measure the belt spacing at the

idler pulley (A, Figure 22). The belt spacing (B) should

be 1-1/4” but no less than 1”. If the measurement is

less than 1”, the belt tension should be adjusted. Refer

to the section entitled “BLADE DRIVE BELT ADJUST-

MENT”.

* IMPORTANT: The blade drive belt on 33” decks does not

require tension adjustment. If the belt becomes worn or

slack it must be replaced. Refer to the section entitled

“BLADE DRIVE BELT REPLACEMENT”.

Blade Brake

1. Check the blade brake for proper function. The blade

should stop rotating in 3 seconds or less after moving

the blade control lever to the “OFF” position or after

releasing the blade pedals.

2. If the blade continues to rotate longer than 3 seconds

do not operate the machine. Refer to the section entitled

“BLADE BRAKE ADJUSTMENT”, or contact your

SNAPPER dealer for assistance.

Service Brake / Park Brake

1. Check the machine brake for proper function:

Engage the park brake, and push the machine. The

rear tires should skid.

Drive the machine forward and apply the brake. The

machine should come to a complete stop in less

than 5 ft.

2. If the brakes are not functioning properly, brake adjust-

ment must be completed before operating the machine.

Refer to the section entitled “SERVICE BRAKE – PARK

BRAKE ADJUSTMENT”.

Maintenance (Continued)

WARNING

Blades must stop rotating in 3 seconds or less after the

blade has been turned off. DO NOT operate machine until

blade brake has been adjusted and functioning properly.

!

WARNING

DO NOT attempt any adjustments, maintenance, service or

repairs with the engine running. STOP engine. STOP blade.

Engage parking brake. Remove key. Remove spark plug

wire from spark plug and secure away from plug. Engine

and components are HOT. Avoid serious burns, allow all

parts to cool before working on machine. Fuel Filler Cap

and vent must be closed securely to prevent fuel spillage.

!

Figure 21: Removing the drive belt cover

B

A

Figure 22: Measuring the belt spacing

A

B

WARNING

The following procedure requires the engine and blades to

be operated. Exercise extreme caution. Clear area of loose

parts & tools first. Only operate blades when seated in the

operator’s seat.

!

Not for

Reproduction

19

Safety Interlock System Checks

Perform the following interlock system checks periodically

during the operating season. Contact your authorized

Snapper dealer if you have questions.

Engine must not

start if:

1. The Clutch/Brake Pedal is not fully depressed OR,

2. The Blade Control is in the “ON” (blades engaged) posi-

tion.

Engine should

start if:

1. The Blade Control is in the “OFF” (blades disengaged)

position AND,

2. The Clutch/Brake Pedal is fully depressed.

Engine and blades must stop

if:

1. The operator rises off of seat with Blade Control in “ON”

(blades engaged) position OR,

2. The operator rises off of seat with Clutch/Brake Pedal

not fully depressed.

Reverse Lockout Mechanism

Check the function of the Reverse Lockout Mechanism with

the engine off.

1. Depress and hold the blade pedals.

2. Depress and hold the clutch/brake pedal.

3. With Steps 1 and 2 performed, the shift lever must not

go into reverse.

Lubrication – Grease Fittings

The following components on the Rear Engine Rider are

equipped with grease fittings and require periodic lubrica-

tion. Apply General Purpose grease (NLGI No.2) with a

grease gun.

1. Front Wheel Bearings. Refer to the section entitled

“FRONT WHEEL BEARINGS – LUBRICATION”.

2. Rear Axle Bearing. Refer to the section entitled “REAR

AXLE BEARING – LUBRICATION”.

3. Mower Blade Spindle. Refer to the section entitled

“MOWER BLADE SPINDLE – LUBRICATION”.

4. Shift Lever. Refer to the section entitled “SHIFT LEVER –

LUBRICATION”.

Check Engine

1. Change the engine oil. Refer to the section entitled

“CHANGE ENGINE OIL”. Refer to the engine manual for

oil specifications.

2. Change the air filter:

• Pull up and rotate the air cleaner latch (A, Figure

23) to remove the air cleaner cover (B).

IMPORTANT: When the cover is removed, you are viewing

the carburetor side of the air filter, which will appear clean.

Remove the filter and pre-cleaner for inspection.

• Remove the air cleaner (C).

• Remove and clean the engine air pre-cleaner

(located behind the air cleaner). Refer to the engine

manual for cleaning and service instructions.

• Install the pre-cleaner and replace the air cleaner

per the engine manual.

• Reinstall the air cleaner cover. Engage the latch

over the cover and rotate and push down to lock.

IMPORTANT: The tabs (D) on the air cleaner cover must be

completely inserted into the corresponding slots in the

engine cover, or the compartment will not be completely

sealed to prevent debris from entering into the carburetor.

Maintenance (Continued)

WARNING

DO NOT operate machine if Reverse Lockout Mechanism is

not functioning properly. Contact your SNAPPER dealer

immediately for assistance.

!

Figure 23: Opening the engine air cleaner cover

B

A

WARNING

DO NOT operate machine if any safety interlock or safety

device is not in place and functioning properly. DO NOT

attempt to defeat, modify or remove any safety device.

!

(Briggs engine shown)

D

C

Not for

Reproduction

www.snapper.com20

Battery Fluid Level

1. Remove the battery. Refer to the section entitled

“BATTERY REMOVAL”.

2. Remove the battery caps. Check the fluid level.

3. Add water only to bring fluid to proper level. DO NOT

OVERFILL.

4. Reinstall the battery. Refer to the section entitled

“BATTERY INSTALLATION”.

Mower Deck Levelness

Check the mower deck for proper level. Adjust as required.

Refer to the section entitled “MOWER DECK ADJUSTMENT –

LEVELNESS”.

Clean Mower Deck

1. Follow the WARNING statement found on this page.

2. Check the fuel level in the tank. If over 3/4 full, remove

the tank. Refer to the section entitled “REMOVING FUEL

TANK”. If 3/4 or less, proceed to the next step.

3. Carefully stand the Rear Engine Rider on the rear

bumper.

4. Clean the underside of the mower deck, removing all

accumulation of grass clippings and debris.

5. Clean the top of the deck, removing all grass clippings

and debris.

Mower Blade Spindle - Lubrication

1. Follow the WARNING statement found on this page.

2. Check the fuel level in tank. If over 3/4 full, remove the

tank. Refer to the section entitled “FUEL TANK

REMOVAL”. If 3/4 or less, proceed to the next step.

3. Carefully stand the Rear Engine Rider on the rear

bumper.

4. Lubricate the spindle grease fitting (A, Figure 24) with

three shots of general purpose grease from a grease

gun.

IMPORTANT: If the Rear Engine Rider will be on its rear

bumper for longer than two hours, remove the battery. Refer

to the section entitled “BATTERY REMOVAL”.

Mower Deck Linkage - Lubrication

Lubricate all mower deck linkage pivot points with a light

coat of motor oil.

Front Wheel Bearing - Lubrication

Lubricate the front wheel grease fittings (A, Figure 25) with

five shots of general purpose grease, from a grease gun.

Shift Lever - Lubrication

Lubricate the shift lever grease fitting (A, Figure 26) with

two shots of general purpose grease from a grease gun.

Maintenance (Continued)

WARNING

DO NOT attempt any adjustments, maintenance, service or

repairs with the engine running. STOP engine. STOP blade.

Engage parking brake. Remove key. Remove spark plug

wire from spark plug and secure away from plug. Engine

and components are HOT. Avoid serious burns, allow all

parts to cool before working on machine. Fuel Filler Cap

and vent must be closed securely to prevent fuel spillage.

!

Figure 25: Front wheel grease fitting

A

Figure 24: Mower blade spindle grease fitting

A

Figure 26: Shift lever grease fitting

A

Not for

Reproduction

La page charge ...

Simplicity MANUAL, OPS, EURO RER Manuel utilisateur

Ce manuel convient également à

Simplicity MANUAL, OPS, EURO RER Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents