GE GFW550SPNDG Manuel utilisateur

Marque: GE

Modèle: GFW550SPNDG

Catégorie: Machines à laver

Taper: Manuel utilisateur

WASHERS

SAFETY INFORMATION ...........3

USING THE WASHER

Getting Started ...................... 5

WiFi Connect ........................14

Loading .............................15

CARE AND CLEANING ........... 16

INSTALLATION

INSTRUCTIONS

.....................18

Reversing The Door Swing (Optional) .....23

TROUBLESHOOTING TIPS ......27

LIMITED WARRANTY ............31

CONSUMER SUPPORT .......... 32

GFW850

GFW650

GFW550

GFW510

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on a label

inside the washer door.

ENGLISH/FRANÇAIS/

ESPAÑOL

GE is a trademark of the General Electric Company. Manufactured under trademark license.

0020508637A 49-3000217 Rev 2 10-19 GEA

2 49-3000217 Rev 2

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-3000217 Rev 2 3

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

To reduce the risk of death, fire, explosion, electric shock, or injury to persons when using

your appliance, follow basic precautions, including the following:

Read all instructions before using the appliance.

Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.

DO NOT wash or dry articles that have been previously cleaned in, washed in, soaked in or spotted with

gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could

ignite or explode.

DO NOT add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used for

2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a

period, before using a washing machine, turn on all hot-water faucets and let the water flow from each for

several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, DO NOT smoke

or use an open flame during this time.

DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children. Before the washer is removed from service or discarded, remove the door or

lid. Failure to follow these instructions may result in death or injury to persons.

DO NOT reach into the appliance if the tub or agitator is moving to prevent accidental entanglement.

DO NOT install or store this appliance where it will be exposed to the weather.

DO NOT tamper with controls, repair or replace any part of this appliance or attempt any servicing unless

specifically recommended in the user maintenance instructions or in published user repair instructions that you

understand and have the skills to carry out.

DO NOT climb or stand on this unit.

DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts including a damaged cord or plug.

Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power pad DOES NOT

disconnect power.

See “ELECTRICAL REQUIREMENTS” located in the Installation Instructions for grounding instructions.

WARNING

4 49-3000217 Rev 2

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

PROPER INSTALLATION

This washer must be properly installed and located in accordance with the Installation Instructions before it is used.

Ensure that the hot water hose is connected to the “H” valve and the cold water hose is connected to the “C”

valve.

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather, which

could cause permanent damage and invalidate the warranty.

Properly ground washer to conform with all governing codes and ordinances. Follow details in the Installation

Instructions.

Ensure washer is properly leveled and washer legs are adjusted such that unit is stable.

Optional drain hose extension recommended for discharging heights from 60” - 96”.

GE Appliances strongly recommends the use of factory specified parts. A list of factory hoses available for

purchase are listed. These hoses are manufactured and tested to meet GE Appliances specifications.

GE Appliances strongly recommends the use of new water supply hoses. Hoses degrade over time and need

to be replaced every 5 years to reduce the risk of hose failures and water damage.

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

PARTS AND ACCESSORIES

Order on-line at GEApplianceparts.com today,

24 hours a day or by phone at 877.959.8688 during

normal business hours. In Canada, visit your local

GE Appliances parts distributor or call 800.661.1616

GEAppliances.ca/en/products/parts-filters-accessories.

Part Number Accessory

WX14X10011 6 ft stainless steel washer hoses with

90° elbows; 2-pack

WH49X316 Washer drain hose extension kit

WX10X10011 Tide

Washing Machine Cleaner*

PM7X2 Universal low profile washer floor tray

GFA28KITN Stack Bracket Kit (to stack dryer on top)

GFP1528S 28” width Pedestal with drawer – White

GFP1528P 28” width Pedestal with drawer – Colors

*Tide

is a registered trademark of Procter & Gamble

WHEN NOT IN USE

Turn off water faucets to minimize leakage if a break or rupture should occur. Check the condition of the fill

hoses; GE Appliances recommends changing the hoses every 5 years.

49-3000217 Rev 2 5

USING THE WASHER

Throughout this manual, features and appearance may vary from your model.

Step 4 Step 5Step 1

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INFORMATION before operating this appliance.

WARNING

(cycle options

vary by model)

Load clothes into your

washer and close the

door.

If the screen is dark,

press the Power pad or

turn the knob to “wake

up” the display.

Turn the knob to

select the desired

cycle.

Open the dispenser and add

detergent, bleach and fabric

softener, as desired. Models

with SmartDispense™ only

require that you select the

SmartDispense pad once the

tank has been filled.

Press Start to begin the

wash cycle. The machine

will weigh your clothes and

add the proper amount of

water. When the wash cycle

is finished, the door will

unlock.

Step 2

Step 3

Quick Start:

Display and Status Lights (Features and appearance will vary)

The display shows the approximate time remaining until the end of the cycle and the washer cycle status (Fill, Wash,

Rinse and Spin).

NOTE: The cycle time is affected by how long it takes the washer to fill. This depends on the water pressure in your

home. The “smart” timer “learns” the amount of time it takes to fill your washer and adjusts the total time accordingly.

If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the

cycle and will stay illuminated for a short time after cycle completion. When this occurs, the washer is taking actions

to correct the out-of-balance condition and complete the cycle normally. In some cases, the washer may not be able

to balance the load and spin up to full speed. If you notice the load is more wet than usual at the end of the cycle,

redistribute the load evenly in the wash tub and run a Rinse & Spin cycle.

In addition, the display will show:

(WiFi)

Will allow your appliance to communicate with your smartphone for remote appliance monitoring,

control and notifications. It stays lit whenever the washer is on and is connected. It will blink during the

commissioning process or if it loses connection to the network.

Venting Venting will blink to indicate that you can select the ULTRAFRESH VENT feature at the end of the cycle. It

then stays illuminated once selected until venting is complete.

Control

The controls on the washer are locked when this icon is illuminated. You must press and hold the Control

Lock pad to unlock the controls.

Door

This icon will illuminate while the door is locked and will blink while the washer is in the process of pausing

and then unlocking.

Auto, More, Less

(on some models)

The SmartDispense will automatically dose detergent according to the weight and soil level of the clothes. You

can adjust this feature to dose 40% MORE or40% LESS detergent or turn it OFF to manually dose detergent.

Tank Low

(on some models)

Will display when the SmartDispense tank needs to be re-filled. Typically, this first lights up when there are

approximately 8 - 10 loads of detergent remaining.

Loads Left

(on some models)

Displays the estimated number of wash loads left for the amount of detergent in the SmartDispense tank.

Getting started

Step 6

After the wash cycle

is completed and the

clothes unloaded, select

ULTRAFRESH VENT™ to

help eliminate the excess

moisture in your washer so

you can close the door.

6 49-3000217 Rev 2

Power

Press to “wake up” the display. If the display is active, press to put the washer into standby “OFF” mode.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

Start and Pause

Press to start a wash cycle. If the washer is running, pressing it once will pause the washer and unlock the door.

It will take a few seconds for the door to unlock after pressing Pause. Press again to restart the wash cycle.

NOTE: If washer is paused and cycle is not restarted within 15 minutes, the current wash cycle will be cancelled.

NOTE: The washer performs automatic system checks after pressing the Start pad. Water will flow in 45

seconds or less. You may hear the door lock and unlock and the pump activate before water flows.

Getting started

USING THE WASHER

Features and appearance will vary.

B E ED

Models:

GFW850

B E ED

Models:

GFW650

B E ED

Models:

GFW550

B E ED

Models:

GFW510

49-3000217 Rev 2 7

USING THE WASHER

Getting started

Wash Cycles

The wash cycles are optimized for specific types of wash loads. The chart below will help you match the items

to be washed with the best wash cycle settings. For optimal performance, select the cycle that most closely

matches the items being washed. Selections and options shown in bold are the suggested settings for that cycle.

Delay Wash/Remote Start is available on all cycles.

Wash

Cycle

Items to Wash Soil Level

Wash

Temp

Spin

Selection

Options Available

Normal Cycle for normal,

regular, or typical use

for washing up to a full

load of normally soiled

cotton clothing.

Extra Heavy

Heavy

Normal

Light

Extra Light

Extra Hot

Hot

Warm

Cold

Tap Cold

Max

High

Medium

Prewash* or Autosoak*

Power Steam*

Time Saver*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Whites Whites and household

linens.

Extra Heavy

Heavy

Normal

Light

Extra Light

Extra Hot

Hot

Warm

Cold

Tap Cold

Max

High

Medium

Low

Prewash* or Autosoak*

Power Steam*

Time Saver*

More Water*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Towels Towels, sheets,

pillowcases and dish

rags.

Extra Heavy

Heavy

Normal

Light

Extra Light

Hot

Warm

Cold

Tap Cold

Max

High

Medium

Low

Prewash* or Autosoak*

Power Steam*

Time Saver*

More Water*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Bulky

Bedding

Large coats, bed

spreads, mattress

covers, sleeping bags,

and similar large bulky

items.

Extra Heavy

Heavy

Normal

Light

Extra Light

Hot

Warm

Cold

Tap Cold

Max

High

Medium

Low

Prewash* or Autosoak*

Power Steam*

Time Saver*

More Water*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Sanitize+

Allergen*

Heavily soiled colorfast

items with the need for

sanitization.

Extra Heavy

Heavy

Extra Hot Max

High

Medium

Low

Prewash

Power Steam*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Sanitize

With Oxi*

Heavily soiled colorfast

items with the need for

sanitization.

Extra Heavy

Heavy

Extra Hot Max

High

Medium

Low

Prewash* or Autosoak*

Extra Rinse

Tumble Care

*Some cycles and options may not be available on some models.

NOTE:

The SANITIZE + Allergen cycle’s water temperatures CANNOT be changed. This cycle utilizes elevated water

temperature and a longer wash cycle to kill dust mites and reduce 99% of common bacteria from fabrics. A pump

purge and extended rinse is incorporated for the purpose of removing contaminants and allergens, such as pet

dander.

The SANITIZE With Oxi cycle’s water temperatures CANNOT be changed. This cycle, when using an Oxi additive

along with your detergent, is designed to remove 99% of bacteria found in home laundry. Measure the detergent and

the Oxi products carefully. Using the amounts appropriate for a large heavily soiled load in a front load washer, follow

the detergent and the Oxi product label instructions. The washer hot water supply connection must provide a minimum

of 120°F to ensure the effectiveness of this cycle.

Only the SANITIZE + Allergen and SANITIZE With Oxi cycles have been designed to meet the requirements of

sanitizing effectiveness.

8 49-3000217 Rev 2

Getting started

USING THE WASHER

Wash Cycles - Continued

The wash cycles are optimized for specific types of wash loads. The chart below will help you match the items

to be washed with the best wash cycle settings. For optimal performance, select the cycle that most closely

matches the items being washed. Selections and options shown in bold are the suggested settings for that cycle.

Delay Wash/Remote Start is available on all cycles.

Wash

Cycle

Items to Wash Soil Level

Wash

Temp

Spin

Selection

Options Available

Power

Clean*

For heavily soiled items

which require extra

cleaning power.

Extra Heavy

Heavy

Normal

Extra Hot

Hot

Warm

Cold

Tap Cold

Max

High

Medium

Low

Prewash

Power Steam

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Quick

Wash

Small loads of lightly

soiled items that are

needed in a hurry.

Normal

Light

Extra Light

Hot

Warm

Cold

Tap Cold

Max

High

Medium

Low

More Water*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Delicates Lingerie and special

care fabrics with light

soil.

Normal

Light

Extra Light

Warm

Cold

Tap Cold

Medium

Low

No Spin

Prewash* or Autosoak*

Time Saver*

More Water*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Cold

Wash

Cycle for normal,

regular, or typical use

for washing up to a full

load of normally soiled

cotton clothing using

only cold water.

Extra Heavy

Heavy

Normal

Light

Extra Light

Cold

Tap Cold

Max

High

Medium

Low

Prewash* or Autosoak*

More Water*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Active

Wear*

Medium to lightly soiled

athletic wear items of

technical or synthetic

fabrics.

Extra Heavy

Heavy

Normal

Light

Extra Light

Warm

Cold

Tap Cold

Medium

Low

No Spin

Prewash

Time Saver

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Rinse &

Spin

For items that need

only to be rinsed, use

this cycle.

Max

High

Medium

Low

No Spin

More Water*

Extra Rinse

Tumble Care* or 1 Step Wash + Dry*

Self

Clean

Cleaning the basket of

residue and odor. No

clothes to be washed

using this cycle.

Medium

*Some cycles and options may not be available on some models.

49-3000217 Rev 2 9

USING THE WASHER

Getting started

Settings

Individual settings for soil level (Level), water temperature (Temp) and spin speed (Spin) can be set from the

minimum to maximum. In general, the higher up the column, the more energy will be used.

Soil

Changing the Soil level increases or decreases the wash time to remove different amounts of soil.

To change the Soil level, press the Soil level pad until you have reached the desired setting. You can choose

between Extra Light, Light, Normal, Heavy or Extra Heavy soil levels on most cycles.

Temp

Adjust to select the proper water temperature for the wash cycle. The AutoSoak and PreWash rinse water is

always cold to help reduce energy usage and reduce setting of stains and wrinkles.

Follow the fabric manufacturer’s care label when selecting the wash temperature.

To change the wash temperature, press the Temp pad until you have reached the desired setting. You can

choose between Tap Cold, Cold, Warm, Hot or Extra Hot on most cycles. By design, to protect fabrics, not all

wash temperatures are available for certain wash cycles. Extra Hot temperatures are enabled by the internal

heater on models equipped with Steam capabilities.

NOTE: The first 10 seconds of the wash fill is always cold. This feature assists in conditioning the fabric and

preventing stains from setting on garments.

Spin

Adjusting the Spin speed changes the final spin speed of the cycles. Always follow the garment manufacturer’s

care label when changing the Spin speed.

To change the Spin speed, press the Spin speed pad until you have reached the desired setting. You can

choose between No Spin, Low, Medium, High or Max. Higher spin speeds are not available on certain cycles,

such as DELICATES and ACTIVE WEAR.

Higher spin speeds remove more water from the clothes and will help reduce dry time, but may also increase

the possibility of setting wrinkles on some fabrics.

NOTE: This washer features a dBT™ (Dynamic Balancing Technology) system. This patented onboard sensing

technology enables real-time balancing of the spin cycle for each load, saving time and providing a quiet wash. This

should lead to more consistent wash times and an overall reduction in noise and vibration. If the washer should

experience any excessive noise, vibration or shaking, simply Pause the washer, open the door, and manually

redistribute the load before restarting the cycle.

Options

SMARTDISPENSE™ (on some models)

When selected, this feature will automatically add detergent to the wash, eliminating the need to add detergent

for each load. See the SmartDispense section for details.

MY SETTINGS (on some models)

To save your favorite settings, set the desired settings for wash cycle, soil level, spin speed and wash temp settings

and hold down the My Settings pad for 3 seconds. A beep will sound to indicate the cycle has been saved.

To use your custom settings, press the My Settings pad before washing a load.

To change the saved settings, set the desired settings and hold down the My Settings pad for 3 seconds.

POWER STEAM (on some models)

Power Steam adds steam into the washer before the wash cycle begins to assist with loosening stains on the

NORMAL, WHITES, TOWELS, BULKY Bedding, SANITIZE+Allergen and POWER CLEAN cycles.

To use:

1. Press the Power pad to “wake up” the washer and select a wash cycle.

2. Press the POWER STEAM pad to activate steam.

3. Press the Start/Pause pad.

WiFi (may be a shared pad with other options)

Press and hold the WiFi* pad for 3 seconds to activate. See the WiFi Connect section for details on how to

get stated with WiFi connection.

10 49-3000217 Rev 2

Getting started

USING THE WASHER

Options

Delay Wash/Remote Start

You can delay the start of a wash cycle for up to 24 hours or remote start the washer by using the Delay Wash/

Remote Start feature. Press to step by hours or hold to scroll the Delay Wash pad to set the amount of time

you want to delay the start of the wash cycle. If you have connected your washer to WiFi, the first selection,

“APP”, can be selected to enable remote starting of your washer from the GE Appliance Smartphone app. Or,

if you select a delay time in hours, the machine will count down and start automatically following this period.

Press the Start pad once you have configured the Delay Wash to the proper setting to enable this feature. To

cancel this option, simply power off and power on the controls.

NOTE: If you forget to fully close the door, a reminder signal will beep reminding you to do so.

NOTE: If you open the door when the delay is counting down, the machine will enter the pause state. You must

close the door and press Start again in order to restart the countdown.

Time Saver (on some models)

This option reduces the overall washer cycle time by optimizing the wash, rinse and spin actions and/or

gently raising the wash temperature to get clothes cleaned faster. Option is available on NORMAL, WHITES,

TOWELS, DELICATES, BULKY Bedding and ACTIVE WEAR cycles. Total wash time will vary based on

cycle chosen and options selected.

To use:

1. Turn power on and select a wash cycle which has Time Saver as an option.

2. Press the Time Saver pad to reduce the overall wash time.

3. Press the Start/Pause pad.

More Water (on some models)

This option adds approximately 3 gallons to the wash and rinse portions of the cycle. If the option is selected

before the cycle starts, the water will be added from the beginning of the wash cycle and later to the rinse. If

the option is selected during the wash portion, more water will be added at this point and later to the rinse.

Likewise, if the More Water option is selected after the wash portion has completed, the washer will add more

water to the rinse only. If wash and rinse have completed, the More Water pad will no longer be active.

ULTRAFRESH VENT System with ODORBLOCK™

The ULTRAFRESH VENT System with OdorBlock was designed to eliminate excess moisture in the washer

following a wash cycle to help prevent odors from developing. This washer was designed to drain water at the

end of the cycle more effectively. Following the wash cycle, the user can then choose to leave the door open

or select the ULTRAFRESH VENT feature to assist with drying out the gasket and other areas of the washer.

The OdorBlock system features multiple components which are manufactured with Microban

antimicrobial

technology.* Microban is a safe and effective antimicrobial technology that will last the life of your washer. For

more information, please visit www.microban.com/geappliances.

ULTRAFRESH VENT is available after the wash cycle is complete and you have removed your cleaned

laundry. Once the door is closed, a notification tune will play and the ULTRAFRESH VENT pad LED will blink.

Upon pressing the pad, ULTRAFRESH VENT will begin.

To select ULTRAFRESH VENT at any other point, power on the washer, ensure a cycle is

not actively running, and remove any garments from the basket, then press and release the

ULTRAFRESH VENT pad so that the notification tune plays and the ULTRAFRESH VENT pad

LED begins to blink. Then press the ULTRAFRESH VENT pad again to start the feature.

During the operation of ULTRAFRESH VENT the door will remain locked and the washer will intermittently spin

at low speeds for up to 8 hours.

If garments are detected in the basket during ULTRAFRESH VENT, the washer will instead run TUMBLE

CARE or 1 STEP WASH + DRY, based on option availability for your model.

The ULTRAFRESH VENT feature may be cancelled at any time by pressing the POWER pad, turning the cycle

knob, or pressing the ULTRAFRESH VENT pad.

*Microban

is a registered trademark of Microban International, Ltd.

49-3000217 Rev 2 11

USING THE WASHER

Getting started

Options

1 STEP WASH + DRY (on some models)

This option is available on all cycles except Self Clean.

The 1 STEP WASH + DRY is intended for small loads only. Use when clothes need to be washed, dried and

ready to wear or finished the next morning. This feature will tumble clothes and introduce a constant stream of

air into the washer compartment upon completion of select wash cycles. Although the drying portion is set to 8

hours, the clothes can be removed at any time by pressing Pause or Power to cancel the cycle.

Tumble Care (on some models)

Freshly tumbles your garments periodically for up to 8 hours after the wash cycle is complete to lessen the

setting of wrinkles and creases when you are not able to move clothing to the dryer right away.

At the end of the cycle, the display will scroll “END” and after ten minutes the Tumble Care will begin. It can be

stopped at any time by pressing the Power pad.

PreWash (on some models)

Prewash is an extra wash before the main wash. Use it for heavily soiled clothes or for clothes with a care label

that recommends prewashing before washing. Be sure to add liquid or powder high-efficiency detergent, or the

proper wash additive to the prewash dispenser. Washers equipped with SmartDispense will automatically add

the proper amount of detergent for prewash based on the load size.

PreWash must be selected prior to pressing Start.

The PreWash feature will fill the washer (adding the prewash detergent), tumble the clothes, drain and spin.

Then the washer will run the selected wash cycle.

NOTE: In some special cycles, the prewash is selected automatically as the default. You can modify this

selection at any time.

AutoSoak (on some models)

For soaking your garments prior to the wash cycle. This option begins with a brief tumble and then proceeds to

soak the clothes with water and detergent for a specified period of time. Once complete, the cycle will continue

automatically. AutoSoak must be selected prior to pressing the start pad. The AutoSoak time will add an

additional 15 minutes, 30 minutes, 1 hour or 2 hours to the overall wash time. High-efficiency detergent from the

main wash compartment in the dispenser is used for the AutoSoak period and main wash cycle.

Extra Rinse

This option allows for an extra rinse during a cycle to remove excess dirt and detergent from soiled loads.

Press the Extra Rinse pad to select.

NOTE: On Rinse & Spin cycle, a drain and spin cycle can be achieved by pressing the Extra Rinse pad until the

LED is no longer illuminated.

Light (on some models)

The basket light will turn on and remain on for 5 minutes when the door opens, Start/Pause pad is pressed, or

by pressing the Light pad.

The basket light can be turned off by pressing and holding the Light pad.

Sound

To change the loudness of the end of cycle signal and the press pad volume, press the Sound pad as many

times as needed to reach the desired volume. There are four sound levels including off.

Control Lock (Light-Control Lock pad) (depending on model)

You can lock the controls to prevent any selections from being made. Or you can lock or unlock the controls

after you have started a cycle.

Children cannot accidentally start the washer by touching pads with this option selected.

To lock/unlock the washer, press and hold the Control Lock/Light-Control Lock pad for 3 seconds. A sound

is made to indicate the lock/unlock status. The control lock icon on the display will light up when it is on.

NOTE: The Power pad can still be used when the machine is locked.

12 49-3000217 Rev 2

Dispenser Drawer

Slowly open the dispenser drawer by pulling it out until

it stops. After adding laundry products, slowly close the

dispenser drawer. Closing the drawer too quickly could

result in early dispensing of the bleach, fabric softener or

detergent.

You may see water in the detergent, bleach and fabric

softener compartments at the end of the cycle. This is a

result of the flushing/siphoning action and is part of the

normal operation of the washer.

Do NOT put detergent packets in the dispenser drawer.

NOTE: Use only liquid or powder HE detergents and

additives in the dispenser drawer. Laundry detergent

packets should only be added directly to the wash

basket following the manufacturer’s directions.

Getting started

USING THE WASHER

Use only HE

High-Efficiency

detergent

SmartDispense™ (on some models)

When selected, this feature will automatically add

detergent to the wash, eliminating the need to add

detergent for each load.

The detergent amount selection on the control

panel will default to AUTO when first powering up

the washing machine. When AUTO is selected, the

amount of detergent needed for each laundry load will

automatically be determined based on the size of the

load the machine senses.

For AUTO, the washer will dispense approximately 1.5 oz

of detergent for an 8 lb normal load. For other loads,

it will adjust proportionally based on the size of load

and garment type. If you select LESS, the amount of

detergent will be reduced by 40%. This may be desired

for higher concentrate detergents or if you have very soft

water. For heavily soiled loads, you may want to select

MORE to add 40% more detergent than the AUTO level.

NOTE: Not all cycles will allow the use of the

SmartDispense feature. If the light is not illuminated

and pressing the SMART DISPENSE pad results in a

beeping tone, then SmartDispense is not allowed for the

cycle that has been selected. Detergent will need to be

added directly to the detergent compartment for these

cycles.

If it is desired to manually select the amount of

detergent for a given load, this can be done by

pressing the SMART DISPENSE pad on the control

panel to select detergent for a Small or Large load.

Small will provide less detergent than average and

Large will provide more detergent than average.

NOTE: If it is desired to manually add detergent for a

load, that detergent will need to be added directly to

the basket, and the SMART DISPENSE set to off for

that particular load.

The smart dispense feature can be disabled by pressing

the SMART DISPENSE pad until off is selected.

Use only HE

High-Efficiency

detergent

Softener

Detergent

Flap Selector

Bleach

SmartDispense

Prewash Compartment (on some models)

Only use the prewash compartment if you are selecting

the PreWash or AutoSoak cycle for heavily soiled clothes.

Add measured detergent or prewash additive to the back

left prewash compartment of the dispenser drawer.

• Detergent or prewash additive is flushed from the

dispenser in the PreWash or AutoSoak cycle (if

selected).

• Detergent usage may need to be adjusted for water

temperature, water hardness, size and soil level of the

load. Avoid using too much detergent in your washer

as it can lead to over sudsing and detergent residue

being left on the clothes.

Softener

Detergent

Flap Selector

Bleach

Add PreWash to

this compartment

49-3000217 Rev 2 13

USING THE WASHER

Getting started

Detergent Compartment

Only use high-efficiency detergent in this washer.

Do NOT fill high-efficiency detergent over the MAX

line. Use detergent manufacturer’s recommended

amount.

• Powder Detergent – Lift the flap up for powder

detergent. This must be done to dissolve and flush

detergent properly. Follow the detergent manufacturer’s

instructions when measuring the amount of powder

detergent to use.

• Liquid Detergent – Keep the flap down for liquid

detergent. This retains the liquid detergent until it

automatically flushes at the start of the wash cycle.

Follow the detergent manufacturer’s instructions when

measuring the amount of liquid detergent to use.

Detergent usage may need to be adjusted for water

temperature, water hardness, size and soil level of the

load. Avoid using too much detergent in your washer as

it can lead to oversudsing, detergent residue being left

on the clothes, and could extend wash times.

Do not put clumped detergent in the dispenser. Clumped

detergent can cause a leak.

Do NOT put detergent

packets in the dispenser

drawer.

Softener

Detergent

Flap Selector

Bleach

SmartDispense

Softener

Detergent

Flap Selector

Bleach

Add PreWash to

this compartment

On models with SmartDispense: On models without SmartDispense:

Liquid Bleach Compartment

If desired, measure out the recommended amount of

liquid bleach, not to exceed 1/3 cup (80 ml) and pour into

the compartment labeled “LIQUID BLEACH” marked

with this symbol .

It is recommended to use High-Efficiency (HE) bleach in

this front-load washer.

Do not exceed the maximum fill line. Overfilling can

cause early dispensing of the bleach which could result

in damaged clothes.

NOTE: Do not use powdered bleach or laundry

detergent/additive packets in the dispenser.

Fabric Softener Compartment

If desired, pour the recommended amount of liquid

fabric softener into the compartment labeled “FABRIC

SOFTENER”.

Use only liquid fabric softener in the dispenser.

Dilute with water to the maximum fill line.

Do not exceed the maximum fill line. Overfilling can

cause early dispensing of the fabric softener, which

could stain clothes.

NOTE: Do not pour fabric softener directly on the wash

load.

14 49-3000217 Rev 2

Getting started

USING THE WASHER

WiFi Label Location

WiFi Connect (For customers in the United States only - on some models)

Your washer is GE Appliances WiFi Connect enabled.

Visit geappliances.com/connect and enter your model number to

show you the proper steps to connect your appliance.

Please visit GEAppliances.com/connect to learn more about

connected appliance features, to learn what connected appliance

app’s will work with your smartphone.

WiFi Connectivity: For assistance with the appliance or the

ConnectPlus network connectivity, please call GE Appliances at

800.GE.CARES.

49-3000217 Rev 2 15

USING THE WASHER

Always follow fabric manufacturer’s care label when laundering.

DO NOT wash fabrics soiled with flammable liquids or cleaning solvents.

No washer can completely remove oil.

DO NOT wash or dry anything that has been soaked in or spotted with any type of oil (including cooking oils).

DO NOT reach into the washer until all moving parts have stopped.

Doing so can result in death, explosion, fire or amputation.

Sorting Wash Loads

Sort by color (whites, lights, colors), soil level, fabric type (sturdy cottons, easy care, delicates) and whether the

fabric produces lint (terry cloth, chenille) or collects lint (velveteen, corduroy). Wash lint producers such as cotton

towels and socks separate from lint collectors including synthetic garments and dress pants.

Loading the Washer

The wash drum may be fully loaded with loosely added items.

To add items after the washer has started, press Start/Pause and wait until the door is unlatched. The washer may

take up to 30 seconds to unlock the door after pressing Start/Pause, depending on the machine conditions. Do not

try to force open the door when it is locked. After the door unlocks, open gently. Add items, close the door and press

Start/Pause to restart.

WARNING

- Fire Hazard

Loading Examples

WORKWEAR LINENS MIXED LOAD DELICATES* QUICK WASH

(2–3 GARMENTS)

4 Jeans

5 Work Wear

Shirts

3 Work Wear

Pants

2 Bath

Sheets

10 Bath

Towels/

Washcloths

7 Hand

Towels/

2 Terrycloth

Bath Mats

2 Flat

Queen-Sized

Sheets

2 Fitted

Queen-Sized

Sheets

Pillowcases

4 Pillowcases

2 Hand Towels

2 Flat Sheets/

2 Fitted Sheets

2 Bath Towels/

4 Washcloths

6 Shirts (Men’s or

Women’s)

4 Pair Pants (Khakis or

Twills)

5 T-shirts

7 Pairs of Boxers

4 Pairs of Shorts

6 T-shirts

4 Pairs of Sweatpants

4 Sweatshirts

2 Hoodies

7 Pairs of Socks

7 Bras

7 panties

3 Slips

2 Camisole

4 Nightgowns

* Using a nylon mesh

bag for small items is

recommended.

2 Casual Wear Work Shirts

1 Pair Casual Wear Work Pants

3 Soccer Uniforms

16 49-3000217 Rev 2

Care and cleaning

CARE AND CLEANING

Self Clean

To clean the interior of the washer, select

the SELF CLEAN feature on the control

panel. This Self Clean cycle should

be performed, at a minimum, once

per month or about every 30-40 wash

cycles. This cycle will use more water,

in addition to bleach, to control the

rate at which soils and detergents may

accumulate in your washer.

NOTE: Read the instructions below

completely before starting Self Clean cycle.

1. Remove any garments or objects from the washer and

ensure the washer basket is empty.

2. Open the washer door and pour

one cup or 250 ml of liquid bleach

or other washing machine cleaner

into the basket.

3. Close the door and select the SELF CLEAN cycle.

Push the Start pad.

4. When the Self Clean cycle is working, the display will

show the estimated cycle time remaining. The cycle

will complete in about 90 minutes. Do not interrupt the

cycle.

5. After the cycle is complete, the washer will automatically

start an ULTRAFRESH VENT operation so that the door

can remain closed until the next time you use the washer.

If for any reason the cycle needs to be interrupted, the

door will not open immediately. Forcing open the door at

this stage may cause water to flood. The door will open

after the water is drained to a level where it would not

flood the floor.

Self Clean may be interrupted by pressing the Start pad

in between cycles. A power outage in the house might

also interrupt the cycle. When the power supply is back,

the Self Clean cycle resumes where it had stopped.

When interrupted, be sure to run a complete Self Clean

cycle before using the washer. If the Power pad is

pressed during Self Clean, the cycle will be lost.

IMPORTANT:

• Run Self Clean with 1 Cup (250 ml) of bleach once a

month.

• After the completion of a Self Clean cycle, the interior

of your washer may have a bleach smell.

• It is recommended to run a RINSE & SPIN or a light

color load after the Self Clean cycle.

Exterior

Immediately wipe off any spills. Wipe with damp cloth. Wipe or dust spills or washing compounds with a damp cloth.

Washer control panel and finishes may be damaged by some laundry pretreatment and stain remover products.

Apply these products away from the washer. The fabric may then be washed and dried normally. Damage to your

washer caused by these products is not covered by your warranty. Do not hit surface with sharp objects.

Interior

Dry around the washer door opening, flexible gasket (including attached hoses) and door glass. These areas should

always be clean to ensure a watertight seal. You will notice if you regularly use the ULTRAFRESH VENT System that

this will not be required as often. It is recommended to rinse the washer at least once per month with 1 cup of bleach

(or other commercially available product manufactured for this purpose, such as Tide

Washing Machine Cleaner)

poured directly into the basket without clothes and using the Self Clean Cycle.

Water Supply Hoses

Hoses connecting washer to faucet should be replaced every 5 years.

Door Gasket

Open the washer door.

Using both hands, press

down the door gasket.

Remove any foreign objects

if found trapped inside the

gasket. Make sure there is

nothing blocking the holes

behind the gasket.

While holding down the door

gasket, inspect the interior

of the gasket by pulling

it down with your fingers.

Remove any foreign objects if found

trapped inside this gasket. Make sure

there is nothing blocking the holes

behind the gasket.

When you are finished cleaning the

door gasket, release it and the gasket

will return to the operating position.

Video

Scan this code

to watch a video

on this topic.

Video

Scan this code

to watch a video

on this topic.

49-3000217 Rev 2 17

CARE AND CLEANING

Care and cleaning

Dispenser Drawer Area

Detergent and fabric softener may build up in the dispenser drawer.

Residue should be removed once or twice a month.

• Remove the drawer by first pulling it out until it stops. Then reach

back into the rear of the drawer cavity and press down firmly on the

lock tab, pulling out the drawer.

• Rinse the drawer with hot water to remove traces of accumulated

laundry products.

• To clean the drawer opening, use a small brush to clean the recess.

Remove all residue from the upper and lower parts of the recess.

• Replace the dispenser drawer.

• To reduce buildup in the Dispenser Drawer area:

Moving and Storage

Ask the service technician to remove water from drain pump and hoses. Do not store the washer where it will be exposed

to the weather. When moving the washer, the tub should be kept stationary by using the shipping bolts removed during

installation. See Installation Instructions in this manual. If these parts are not available, they can be ordered by visiting

our Website at GEApplianceparts.com or by calling GE Appliances at 877.959.8688. In Canada, visit your local

GE Appliances parts distributor or call 800.661.1616 or GEAppliances.ca/en/products/parts-filters-accessories.

Long Vacations

Be sure water supply is shut off at faucets. Drain all water from hoses and water filter pump area if weather will be

below freezing.

On models with

SmartDispense:

On models without

SmartDispense:

Use only HE

High-Efficiency

detergent

1. Using a small flathead screwdriver or coin, open the access door.

2. Place a shallow pan or dish under the pump access door and towels on the

floor in front of the washer to protect the floor. It is normal to catch about a cup

of water when the filter is removed.

3. Pull down the pour spout.

4. Turn the pump filter counterclockwise and remove the filter slowly, controlling

the flow of the draining water.

5. Remove the filter and clean the debris from the filter.

6. Replace the filter and turn clockwise. Tighten securely.

7. Flip up the pour spout.

8. Close the access door by hooking the bottom tabs first, then rotating the

access door shut.

Video

Scan this code

to watch a video

on this topic.

Pump Filter

Due to the nature of the front-load washer, it is sometimes possible for small articles to pass to the

pump. The washer has a filter to capture lost items so they are not dumped to the drain. To retrieve

lost items, clean out the pump filter.

18 49-3000217 Rev 2

Installation

Washer

Instructions

If you have any questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our

Website at: GEAppliances.com

In Canada, call 800.561.3344 or visit GEAppliances.ca

TOOLS REQUIRED

Level

Adjustable wrench

Channel-lock adjustable pliers

Phillips screwdriver

PARTS SUPPLIED

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these

instructions for local inspector’s use.

• IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

• Completion time – 1-3 hours

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

Shipping

Bolt Covers

Drain Hose Guide

DO NOT Install the Washer:

1. In an area exposed to dripping water or outside weather

conditions. The ambient temperature should never be

below 60°F (15.6°C) for proper washer operation.

2. In an area where it will come in contact with curtains

or drapes.

3. On carpet. The floor MUST be a hard surface with

DPD[LPXPVORSHRIƎSHUIRRWFPSHU

cm). To make sure the washer does not vibrate or

move, you may have to reinforce the floor.

NOTE:,IIORRULVLQSRRUFRQGLWLRQXVHƎLPSUHJQDWHG

plywood sheet solidly attached to existing floor

covering.

LOCATION OF YOUR WASHER

MOBILE HOME INSTALLATION:

Installation must conform to Standard for Mobile Homes,

ANSI A119.1 and National Mobile Home Construction

and Safety Standards Act of 1974 (PL93-383).

Lock Bar (Retain for

Reversing the Door

Swing option)

Cable Tie

PARTS REQUIRED (Sold separately

or included with the GFW510 model)

Water Hoses (2)

Rubber Washers (2) and

Strainer Screens (2)

GE Appliances Parts and Accessories

Order on-line at GEApplianceparts.com today,

24 hours a day or by phone at 877.959.8688 during

normal business hours. In Canada, visit your local

GE Appliances parts distributor or call 800.661.1616

or GEAppliances.ca/en/products/parts-filters-

accessories.

Part Number Accessory

WX14X10011 6 ft stainless steel washer hoses with

90° elbows; 2-pack

WH1X2267 Rubber Washer (1) and Screen (1)

49-3000217 Rev 2 19

ACCESSORIES:

Order on-line at GEApplianceparts.com, 24 hours a day or

by phone at 877.959.8688 during normal business hours.

Follow the Installation Instructions included in the Kit for all

clearances and installation requirements.

Installation Instructions

WASHER

DIMENSIONS

Side View

32” (81.3 cm)

54-1/2” (138.4 cm)

Models - GFW650, GFW550, GFW510:

Side View

34” (86.4 cm)

56-1/2” (143.8 cm)

Model - GFW850:

28”

(71.2 cm)

*39-3/4”

(101 cm)

Front View

NOTE:

With leveling legs retracted: 39-3/4 (101 cm).

With leveling legs fully extended: 40-5/8 (103.1 cm).

MINIMUM

CLEARANCES

0”

Alcove or Closet

• Rear = 0”*

• Sides = 0”

• 7RS Ǝ

• )URQW Ǝ

0”0”0”

Part Number Accessory

GFP1528SNWW

White Pedestal

GFP1528PNSN

Satin Nickel Pedestal

GFP1528PNRS Royal Sapphire Pedestal

GFP1528PNDG Diamond Gray Pedestal

GFA28KITN Stacking Kit for Dryer over Washer

Stacked:

79-1/2”*

(202 cm)

Pedestal:

55-7/8”*

(141.8 cm)

• Consideration must be given to provide adequate clearance for installation and service.

• Closet doors must be louvered or otherwise ventilated and have at least 60 square inches (387.1 cm

) of open area. If the

closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches (774.2 cm

) of open area.

* To enable 0” clearance on the back of the washer, you must use 90° elbow hoses. Otherwise you may require some

additional clearance to avoid rubbing of the hoses against the back wall.

20 49-3000217 Rev 2

Installation Instructions

1. Cut and remove all packaging straps.

2. While it is in the carton, carefully lay the washer on its

side. DO NOT lay the washer on its front or back.

3. Turn down the bottom flaps. Remove all base packaging

including the styrofoam base.

4. Carefully return the washer to an upright position and

remove the carton by lifting it upward.

5. Carefully move the washer to within 4 feet (122 cm)

of the final location.

6. Remove the following from the back side of the washer:

4 bolts

4 plastic spacers (including power cord retainers and

rubber grommets)

2 brackets

NOTE: Do NOT remove the screw or clip holding the

hose.

UNPACKING THE WASHER UNPACKING THE WASHER (cont.)

7. Insert shipping bolt hole covers into shipping bolt

holes.

Recycle or destroy the carton and

plastic bags after the washer is

unpacked. Make materials inaccessible to children.

Children might use them for play. Cartons covered

with rugs, bedspreads or plastic sheets can become

airtight chambers causing suffocation.

WARNING

NOTES:

• Failure to remove the shipping braces can cause

the washer to become severely unbalanced.

• IMPORTANT: Save all bolts for future use.

If you must transport the washer at a later date,

you must reinstall the shipping support hardware to

prevent shipping damage. Keep the hardware in the

plastic bag provided.

La page charge ...

GE GFW550SPNDG Manuel utilisateur

Marque: GE

Modèle: GFW550SPNDG

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: GE GFW550SPNDG User manual
español: GE GFW550SPNDG Manual de usuario

GE GFW550SPNDG Manuel utilisateur

GE GFW550SPNDG Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents