Poulan Pro SM4018 Manuel utilisateur

Marque: Poulan Pro

Modèle: SM4018

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Poulan PRO

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pa8 retourner routil au detaillant.

•1-800-554-6723

www.poulan-pro.com

Instruction Manual

Manual de Instrucciones

Manuel d'lnstructions

For Occasional Use Only

SM4018 /

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENOIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en le-

siones graves.

AVERTISSEMENT:

Lire le manuel d'instructions et bien respecter tousles avertisse-

ments et toutes les instructions de s6curite. Tout defaut de le

faire pourrait entraTner des blessures graves.

Poulan PRO

1030 Stevens Creek Road

Augusta, GA30907

545123649 8/25/06

f_l

WARNING! This chain I_1

saw can be dangerous! Care-

less or improper use can cause

serious or even fatal injury.

Read and understand the

instruction manual before

using the chain saw.

Always wear appropriate ear protection, eye protection and head protection.

• A

Always use two hands when operating the chain saw.

WARNING! contactingtheguidebartipwithanyobject

should be avoided; tip contact may cause the guide bar to

move suddenly upward and backward, which may cause se-

rious injury.

Measured maximum kickback value without chain brake for the bar

and chain combination on the label

_ WARNING: Always disconnect

spark plug wire and place wire where itcan-

not contact spark plug to prevent accidental

starting when setting up, transporting, ad-

justing or making repairs except carburetor

adjustments.

Because a chain saw is a high-speed wood-

cutting tool, special safety precautions must

be observed to reduce the risk of accidents.

Careless or improper use of this tool can

cause serious injury.

PLAN AHEAD

• Read this manual carefully until you com-

pletely understand and can follow all safety

rules, precautions, and operating instruc-

tions before attempting to use the unit.

• Restrict the use of your saw to adult users

who understand and can follow safety

rules, precautions, and operating h_struc-

tions found in this manual.

• Wear protective gear. Always use steeF

toed safety footwear with non-slip soles;

snug-fitting clothing; heavy-duty, non-slip

gloves; eye protection such as non-fog-

ging, vented goggles or face screen; an

approved safety hard hat; and sound barri-

ers (ear plugs or mufflers) to protect your

hearing. Regular users should have hear-

ing checked regularly as chain saw noise

can damage hearing. Secure hair above

shoulder length.

Hearing Safety Hat

Protection _ Eye

*_"_ ii _ _"" Protection

Snug

Fittinc Heavy Duty

Clothing Gloves

Safety Safety Chaps

Shoes

Keep all parts of your body away from the

chain when the engine is running.

Keep children, bystanders, and animals a

minimum of 30 feet (10 meters) away from

the work area. Do not allow other people

or animals to be near the chain saw when

starting or operating the chain saw.

Do not handle or operate a chain saw

when you are fatigued, ill, or upset, or if you

have taken alcohol, drugs, or medication.

You must be in good physical condition

and mentally alert. Chain saw work is

strenuous. If you have any condition that

might be aggravated by strenuous work,

check with your doctor before operating a

chain saw.

• Carefullyplanyoursawingoperationinad-

vance.Donotstartcuttinguntilyouhavea

clearworkarea,securefooting,and,ifyou

arefellingtrees,aplannedretreatpath.

OPERATEYOURSAW SAFELY

• Do not operate a chain saw with one hand.

Serious injury to the operator, helpers, by-

standers or any combination of these per-

sons may result from one-handed opera-

tion. A chain saw is intended for

two-handed use.

• Operate the chain saw only in a well-venti-

tated outdoor area.

• Do not operate saw from a ladder or in a

tree.

• Make sure the chain will not make contact

with any object while starting the engine.

Never try to start the saw when the guide

bar is in a cut.

• Do not put pressure on the saw at the end

of the cut. Applying pressure can cause

you to lose control when the cut is com-

pleted.

• Stop the engine before setting the saw

down.

• Do not operate a chain saw that is dam-

aged, improperly adjusted, or not com-

pletely and securely assembled. Always

replace bar, chain, hand guard, or chain

brake immediately if it becomes damaged,

broken or is otherwise removed.

• With the engine stopped, hand carry the

chain saw with the muffler away from your

body, and the guide bar and chain to the

rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

• Have all chain saw service performed by a

qualified service dealer with the exception

of the items listed in the maintenance sec-

tionofthis manual. Forexample, ifimprop-

er toots are used to remove or hold the fly-

wheel when servicing the clutch, structural

damage to the flywheel can occur and

cause the flywheel to burst.

• Make certain the saw chain stops moving

when the throttle trigger is released. For

correction, refer to CARBURETOR AD-

JUSTMENTS.

• Never modify your saw in any way.

• Keep the handles dry, clean, and free of oil

or fuel mixture.

• Keep fuel and oil caps, screws, and fas-

teners securely tightened.

• Use only Poulan PRO accessories and re-

placement parts as recommended.

HANDLE FUEL WITH CAUTION

• Do not smoke while handling fuel or while

operating the saw.

• Eliminate all sources of sparks or flame in

the areas where fuel is mixed or poured.

There should be no smoking, open flames,

or work that could cause sparks. Allow en-

gine to coot before refueling.

• Mix and pour fuel in an outdoor area on

bare ground; store fuel in a cool, dry, well

ventilated place; and use an approved,

marked container for all fuel purposes.

Wipe up all fuel spills before starting saw.

•Move at least 10 feet (3 meters) from fuel-

ing site before starting engine.

• Turn the engine off and let saw cool in a

non-combustible area, not on dry leaves,

straw, paper, etc. SIowly remove fuel cap

and refuel unit.

• Store the unit and fuel in an area where fuel

vapors cannot reach sparks or open

flames from water heaters, electric motors

or switches, furnaces, etc.

KICKBACK

,_ WARNING: Avoid kickback which

can result in serious injury. Kickback is the

backward, upward or sudden forward motion

of the guide bar occurring when the saw

chain near the upper tip of the guide bar con-

tacts any object such as a log or branch, or

when the wood closes in and pinches the

saw chain in the cut. Contacting a foreign ob-

ject in the wood can also result in loss of

chain saw control,

• Rotational Kickback can occur when the

moving chain contacts an object at the up-

per tip of the guide bar. This contact can

cause the chain to dig into the object,

which stops the chain for an instant, The

result is a lightning fast, reverse reaction

which kicks the guide bar up and back to-

ward the operator.

•Pinch-Kickback can occur when the the

wood closes in and pinches the moving

saw chain in the cut along the top of the

guide bar and the saw chain is suddenly

stopped. This sudden stopping of the

chain results in a reversal of the chain

force used to cut wood and causes the

saw to move in the opposite direction of the

chain rotation, The saw is driven straight

back toward the operator.

•Pull-In can occur when the moving chain

contacts a foreign object in the wood in the

cut along the bottom of the guide bar and the

saw chain issuddenly stopped. This sudden

stopping pulls the saw forward and away

from the operator and could easily cause the

operator to lose control of the saw.

Avoid Pinch-Kickback:

• Be extremely aware of situations or ob-

structions that can cause material to pinch

the top of or otherwise stop the chain,

• Do not cut more than one log at a time,

• Do not twist the saw as the bar is with-

drawn from an undercut when bucking,

Avoid Pull-In:

• Always begin cutting with the engine at full

speed and the saw housing against wood.

• Use wedges made of plastic or wood.

Never use metal to hold the cut open.

Kickback Path

ClearTheWorkingArea

REDUCETHE CHANCE OF

KICKBACK

• Recognize that kickback can happen.

With a basic understanding of kickback,

you can reduce the element of surprise

which contributes to accidents,

• Never let the moving chain contact any ob-

ject at the tip of the guide bar,

• Keep the working area free from obstruc-

tions such as other trees, branches, rocks,

fences, stumps, etc. Eliminate or avoid

any obstruction that your saw chain could

hit while you are cutting, When cutting a

branch, do not let the guide bar contact

branch or other objects around it,

• Keep your saw chain sharp and properly

tensioned. A loose or dull chain can in-

crease the chance of kickback occurring,

Follow manufacturer's chain sharpening

and maintenance instructions. Check ten-

sion at regular intervals with the engine

stopped, never with the engine running.

Make sure the chain brake nuts are se-

curely tightened after tensioning the chain.

• Beginandcontinuecuttingatfulispeed. If

the chain is moving at a slower speed,

there is greater chance of kickback occur-

ring.

• Cut one log at a time,

• Use extreme caution when re-entering a

previous cut.

• Do not attempt cuts starting with the tip of

the bar (plunge cuts),

• Watch for shifting logs or other forces that

could close a cut and pinch or fall into

chain,

• Use the Reduced-Kickback Guide Bar

and Low-Kickback Chain specified for

your saw,

MAINTAIN CONTROL

Stand to the left

of the sa_

Never reverse _

hand positions

tElbow locked

Thumb on underside of

handlebar

•Keep a good, firm grip on the saw with both

hands when the engine is running and

don't let go, A firm grip will help you reduce

kickback and maintain control of the saw.

Keep the fingers of your left hand encir-

cling and your teft thumb under the front

handlebar. Keep your right hand com-

pletely around the rear handle whether

your are right handed or teft handed, Keep

your left arm straight with the elbow

locked,

• Position your teft hand on the front handle-

bar so it is in a straight line with your right

hand on the rear handle when making

bucking cuts. Never reverse right and left

hand positions for any type of cutting,

• Stand with your weight evenly balanced on

both feet,

• Stand slightly to the left side of the saw to

keep your body from being in a direct line

with the cutting chain,

• Do not overreach. You could be drawn or

thrown off balance and lose control of the

saw.

• Do not cut above shoulder height. It is diffi-

cult to maintain control of saw above

shoulder height.

KICKBACK SAFETY FEATURES

WARNING: The following features

are included on your saw to help reduce the

hazard of kickback; however, such features

will not totally eliminate this danger, As a

chain saw user, de not rely only on safety de-

vices, You must follow all safety precau-

tions, instructions, and maintenance in this

manual to help avoid kickback and other

forces which can result in serious injury.

• Reduced-Kickback Guide Bar, designed

with a small radius tip which reduces the

size of the kickback danger zone on the

bar tip, A Reduced-Kickback Guide Bar

has been demonstrated to significantly re-

duce the number and seriousness of kick-

backs when tested in accordance with

safety requirements for gasoiine powered

chain saws as set by ANSI Bt75.1.

Reduced Kickback Symmetrical Guide Bar

__all Radius Tip

SymmetricalGuideBar _.

[Large Radius Tip

• Low-Kickback Chain, designed with a

contoured depth gauge and guard link

which deflect kickback force and allow

wood to gradually ride into the cutter. Low-

Kickback Chain has met kickback per-

formance requirements when tested on a

representative sample of chain saws be-

tow 3.8 cubic inch displacement specified

in ANSI B175.1.

Contoured Depth Gauge

D Elongated Guard Link

....

Low-Kickback _ and allowswood

Chain to gradually ride

into oulter

i_Can Obstruct Matedal

Not a Low- Kickback Chain

• Front Hand Guard, designed to reduce the

chance of your left hand contacting the chain

if your hand slips off the front handlebar.

• Position of front and rear handlebars, de-

signed with distance between handtes and

"in-line" with each other. The spread and

"in-line" position of the hands provided by

this design work together to give balance

and resistance in controlling the pivot of

the saw back toward the operator if kick-

back occurs.

CHAIN BRAKE AND CKA ANGLE

• Chain Brake, designed to stop the chain in

the event of kickback.

_L.WARNING: WE DO NOT REP-

RESENT AND YOU SHOULD NOT AS-

SUME THAT THE CHAIN BRAKE WiLL

PROTECT YOU IN THE EVENT OF A

KICKBACK. Kickback is a lightning fast ac-

tion which throws the bar and rotating chain

back and up toward the operator. Kickback

can be caused by allowing contact of the bar

tip in the danger zone with any hard object.

Kickback can also be caused by pinching the

saw chain along the top of the guide bar. This

Computed kickback angle (CKA) Table

BAR

MODEL P/N Length

SM4018 952044418 18"

action may push the guide bar rapidly back

toward the operator. Either of these events

may cause you to lose control of the saw

which could result in serious injury or even

death. DO NOT RELY UPON ANY OF THE

DEVICES BUILT INTO YOUR SAW. YOU

SHOULD USE THE SAW PROPERLY AN D

CAREFULLY TO AVOID KICKBACK. Re-

duced-kickback guide bars and low-kick-

back saw chains reduce the chance and

magnitude of kickback and are recom-

mended. Your saw has a low kickback chain

and bar as original equipment. Repairs on a

chain brake should be made by an autho-

rized servicing dealer. Take your unit to the

place of purchase if purchased from a ser-

vicing dealer, or to the nearest authorized

master service dealer.

•Tip contact in some cases may cause a light-

ning fast reverse REACTION, kicking the

guide bar up and back toward the operator.

• Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly

back toward the operator.

• Either of these reactions may cause you to

lose controt of the saw which could result

in serious injury.Do not rely exclusively

upon the safety devices built into your saw.

_L, WARNING: Computed kickback

angle (CKA) listed on your saw and listed in

the CKA table below represents angle of

kickback your bar and chain combinations

will have when tested in accordance with

CSA and ANSI standards. When purchasing

replacement bar and chain, considerations

should be given to the lower CKA values.

Lower CKA values represent safer angles to

the user, higher values indicate more angle

and higher kick energies. Computed angles

represented in the non-activated column in-

dicate total energy and angte associated

without activation of the chain brake during

kickback. Activated angle represents chain

stopping time relative to activation angle of

chain brake and resulting kick angle of saw.

in all cases lower CKA values represent a

safer operating environment for the user.

The following guide bar and chain combina-

tions meet kickback requirements of CSA

Z62.1, Z62.3. & ANSi Bt75.1 when used on

saws listed in this manual= Use of bar and

chain combinations other than those listed is

not recommended and may not meet the

CKA requirements per standard.

CHAIN P/N CKA without chain brake

952051548 14 °

NOTE: If this saw is to be used for commer-

cial logging, a chain brake is required and shall

not be removed or otherwise disabled to com-

ply with Federal OSHA Regulations for Com-

merciaI Logging.

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorders or

abnormal swellings. Prolonged use in cold

weather has been linked to blood vessel

damageinotherwisehealthypeople.If

symptomsoccursuchasnumbness,pain.

lossofstrength,changeinskincolorortexture.

orlossoffeelinginthefingers,hands,orjoints,

discontinuetheuseofthistoolandseek

medicalattention.Ananti-vibrationsystem

doesnotguaranteetheavoidanceofthese

problems.Userswhooperatepowertoolson

acontinualandregaiarbasismustmonitor

closelytheirphysicalconditionandthe

conditionofthistool.

SPECIALNOTICE:Yoursawisequipped

withatemperaturelimitingmufflerandspark

arrestingscreenwhichmeetsthe

requirementsofCaliforniaCodes4442and

4443.AllU.S.forestlandandthestatesof

California,Idaho,Maine,Minnesota,New

Jersey,Oregon,andWashingtonrequireby

lawthatmanyinternalcombustionengines

tobeequippedwithasparkarrestingscreen.

IfyouoperateachainsawinastateorIocale

wheresuchregulationsexist,youarelegally

responsibleformaintainingtheoperating

conditionoftheseparts.Failuretodosois

aviolationofthelaw.RefertotheSERVlCE

sectionformaintenanceofthespark

arrestingscreen.

FailuretofollowallSafetyRulesandPrecau-

tionscanresultinseriousinjury.Ifsituations

occurwhicharenotcoveredinthismanual,

usecareandgoodjudgement.Ifyouneed

assistance,contactyourauthorizedservice

dealerorcall1-800-554-6723.

STANDARDS:ThissawislistedbyUnder-

writer'sLaboratories,Inc.,andtheCanadian

StandardsAssociationinaccordancewith:

ANSIB175.1-2000AmericanNational

StandardforPoweredTools- Gasoline

PoweredChainSaw-SafetyRequirements

CSAZ62.1-03ChainSaws-Occupational

HealthandSafety

CSAZ62.3-96ChainSawKickbackOccu-

pationaiHealthandSafety

Protectivegloves(notprovided)shouldbe

wornduringassembly.

ATTACHINGTHE BAR & CHAIN (If not

already attached)

WARNING: If received assembled,

repeat all steps to ensure your saw is properly

assembled and all fasteners are secure. At-

ways wear gloves when handling the chain.

The chain is sharp and can cut you even when

it is not moving!

1. Loosen and remove the chain brake nuts

and the chain brake from the saw.

2. Remove the plastic shipping spacer (if

present).

Location of shipping spacer

a_ Chain Brak_e

Ch Nuts

Bar Tool

3. An adjusting pin and screw is used to ad-

just the tension of the chain. It is very im-

portant when assembling the bar. that the

pin located on the adjusting screw aligns

into a hole in the bar. Turning the screw will

move the adjustment pin up and down the

screw. Locate this adjustment before you

begin mounting the bar onto the saw. See

illustration below.

Inside view of

_C_ _hain Brake

Adjustment located on Chain Brake

4. Turn the adjusting screw by hand coun-

terclockwise until the adjusting pin just

touches the stop. This should allow the

pin to be near the correct position.

5. Slide guide bar behind clutch drum until

guide bar stops against clutch drum

sprocket.

6. Carefully remove the chain from the pack-

age. Hold chain with the drive links as

shown.

_ ip of

Bar

DIIREOTION OF ROTATION

Cutters DepthGauge

DriveLinks

Placechainontothesprocket

7. Placechainoverandbehindclutch,fitting

thedrivelinksintheclutchdrumsprocket.

8. Fitbottomofdrivelinksbetweenthe

teethinthesprocketinthenoseofthe

guidebar>

9. Fitchaindrivelinksintobargroove.

10.Pullguidebarforwarduntilchainissnug

inguidebargroove.Ensurealldrive

linksareinthebargroove.

11.Now,installchainbrakemakingsurethe

adjustingpinispositionedinthelower

holeintheguidebar>Rememberthispin

movesthebarforwardandbackwardas

thescrewisturned.

12.Installchainbrakenutsandfingertighten

only.Oncethechainistensioned,you

winneedtotightenchainbrakenuts.

CHAIN TENSION (Including units

with chain already installed)

NOTE: When adjusting chah_ tension,

make sure the chah_ brake nuts are finger

tight only. Attempting to tension the chain

when the chain brake nuts are tight can

cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move the chain around

the bar. If the chain does not rotate, it is too

tight. If too loose, the chain will sag below the

bar.

Chain Adjustment

Chain Brake Nuts Tool (Bar Tool)

Adjusting the tension:

Chah_ tension is very h-nportant. Chain

stretches during use. This is especially true

during the first few times you use your saw.

Always check chain tension each time you

use and refuel your saw.

You can adjust the chain tension by loosen-

ing the chain brake nuts and turning the ad-

justing screw 1/4 of a turn while lifting up on

the bar.

•If chain is too tight, turn adjusting screw 1/4

turn counterclockwise.

• If chain is too loose, turn adjusting screw

1/4 turn clockwise.

f--2_ _-%'J/Adju sting / /

,,,.,',t_ i',_..,.C_ll_ Screw _ j

Chain Brake Nuts Guide Bar

Adjusting Screw - 1/4 Turn

• Lift up the tip of the bar and securely tight-

en the chain brake nuts with the bar tool.

• Recheck chain tension.

_'_ Cht_n Brake _lL _. _

i_ WARNING: If the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

KNOW YOUR SAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of

the various controls and adjustments. Save this manual for future reference.

Chain

Adjustment Tool Front Hand Guard Front Handle

(BarTool) r_ __/ Starter Rope

Chain Muffler -___._ __ Primer

Housing Fuel Mix Fill Cap

Cylinder Cover

Throttle Chain

Direction

Rear Lockout Adjustin of Travel

Handle Screw _

Throttle Choke/ Chain Chain

Trigger Fast Idle Brake Catcher

Lever

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the

engine.

THROTTLE TRIGGER

The THROTTLE TRIGGER controls engine

speed.

THROTTLE LOCKOUT

The THROTTLE LOCKOUT must be pressed

before you can squeeze the throttle trigger.

This feature prevents you from accidentally

squeezing the trigger.

CHOKE/FAST IDLE LEVER

The choke and fast idle are set by pulling the

CHOKE/FAST IDLE LEVER out to the full ex-

tent for cold starting or after refueling. The

choke provides additional fuel to the engine

during cold starting.

PRIMER BULB

The PRIMER BULB circulates fuel to the

carburetor to provide quicker starting.

Chain Brake Nuts Guide Bar

CHAIN BRAKE

The CHAIN BRAKE is a device designed to

stop the chain if kickback occurs. The chain

brake activates automatically in the event of

kickback. The chain brake activates manu-

ally ifthe front hand guard is pushed forward.

The chain brake is disengaged by pulling the

front hand guard back toward the front han-

dle as far as possible.

CHAIN TENSION

It is normal for a new chain to stretch during first

30 minutes of operation. You should check

your chain tension frequently. See CHAIN

TENSION under the ASSEMBLY section.

_L, WARNING: Muffler is very hot dur-

ing and after use. Do not touch the muffler or

allow combustible material such as dry

grass or fuel to do so.

_ WARNING: Removefuelcapslow-

lywhen refueling.

FUELING ENGINE

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good quatity

synthetic 2-cycle air-cooled engine oil

designed to be mixed at a ratio of 40:1.

Poulan/WEED EATER brand synthetic oil is

recommended. A 40:1 ratio is obtained by

mixing 3.2 ounces (95 ml) of oilwith 1 gallon (4

liters) of unleaded gasoline. Included with this

saw is a 3.2 ounce container of Poulan/WEED

EATER brand synthetic oil. Pour the entire

contents of this container into 1 gallon of

gasoline to achieve the proper fuel mixture. DO

NOT USE automotive or boat oil. These oils

will cause engine damage. When mixing fuel

follow the instructions printed on the

container. Always read and follow the safety

rules listed under HANDLE FUEL WITH

CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require conth_uous _ubri-

cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too littIe oil will cause overheating

shown by smoke coming from the chain and/

or discoloration of the bar.

In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a

small amount (5 to 10%) of #1 Diesel Fuel or

kerosene. Bar and chain oil must be free

flowing for the oil system to pump enough oil

for adequate lubrication.

Genuine Poulan or Poulan PRO bar and

chain oil is recommended to protect your unit

against excessive wear from heat and

friction. Poulan or Poulan PRO oil resists

high temperature thinning. If Poulan or

Poulan PRO bar and chain oil is not

available, use a good grade SAE 30 oil.

• Never use waste oil for bar and chain lubri-

cation.

• Always stop the engine before removing

the oil cap.

IMPORTANT

Experience indicates that alcohol-blended

fuels (caHed gasohol or using ethanol or

methanol) can attract moisture which leads

to separation and formation of acids during

storage. Acidic gas can damage the fuel

system of an engine while in storage. To

avoid engine problems, the fuel system

shouM be emptied before storage for 30

days or longer. Drain the gas tank. start the

engine and let it run unti_ the fueI lines and

carburetor are empty. Use fresh fuel next

season. See STORAGE section for addi-

tional information.

£A

d_WARNING: The chain must not

move when the engine runs at idle speed. If

the chain moves at idle speed refer to CAR-

BURETOR ADJUSTMENT within this

manual, Avoid contact with the muffler. A hot

muffler can cause serious burns,

To stop the engine move the ON/STOP

switch to the STOP position,

To start the engine hold the saw firmly on the

ground as illustrated, Make sure the chain is

free to turn without contacting any object.

Use only 15 - 18 inches (38 - 45 om) of

rope per pull.

Hold saw firmly while pulling starter rope.

Starter rope handle

l{ , ,_\_['_ Left hand

_, ("_,_ _:)_f2;I_--- on front

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pul_ingthe starter rope, do not use the full

extent of the rope as this can cause the rope to

break. Do not let starter rope snap back. Hold

the handle and let the rope rewind slowty.

For cold weather starting, start the unit at

FULL CHOKE; allow the engine to warm up

before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/

fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or

warm engine after running out of

fuel):

NOTE: In the following steps, when the

choke/fast idle lever is pulled out to the full

extent, the correct throttle setting for starting

is set automatically.

ON/STOP SWITCH

(_SIDE VIEW)

_" ,_'.." STOP

1. Move ON/STOP switch to the ON posi-

tion.

2. Pull out choke/fast idle to the full extent

(to the FULL CHOKE position).

3. Slowly press primer bulb 6 times.

4. Pull the starter rope sharply 5 times with

your right hand. Then, proceed to the

next step.

NOTE: If the engine sounds as if it is trying

to start before the 5th pull, stop pulling and

immediately proceed to the next step.

5. Push the choke/fast idle lever in to the

HALF CHOKE position.

CHOKE/FASTIDLELEVER

IEW)

..,...,J J

Choke/ /It It It

fast idle lever OFF HALF FULL

6. Pull the starter rope sharply with your

right hand until the engine starts.

7. Allow the engine to run for approximately

5 seconds. Then, squeeze and release

throttle trigger to allow engine to return to

idle speed.

STARTING A WARM ENGINE:

1. Move ON/STOP switch to the ON posi-

tion.

2. Pull the choke/fast idle lever out to the

HALF CHOKE position.

3. Slowly press the primer bulb 6 times.

4. Pull the starter rope sharply with your

right hand until the engine starts.

5. Squeeze and release throttle trigger to

allow engine to return to idle speed.

DIFFICULT STARTING (or starting a

flooded engine):

The engine may be flooded with too much

fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess

fuel by pushing the choke/fast idle lever in

completely (to the OFF CHOKE position)

and then following the warm engine starting

procedure listed above. Ensure the ON/

STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

the unit is flooded. If engine fails to start, refer

to the TROUBLESHOOTING TABLE or call

1-800-554-6723.

CHAIN BRAKE

_WARNING: If the brake band is

worn too thin it may break when the chain

brake is triggered. With a broken brake band,

the chain brake will not stop the chain. The

chain brake should be replaced by an autho-

rized service dealer ifany part is worn to less

than 0.020" (0.5 ram) thick. Repairs on a

chain brake should be made by an autho-

rized service dealer. Take your unit to the

place of purchase if purchased from a ser-

vicing dealer, or to the nearest authorized

master service dealer.

• This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

• The inertia-activated chain brake is

activated if the front hand guard is pushed

forward, either manually (by hand) or

automatically (by sudden movement).

• If the brake is already activated, it is

disengaged by pulling the front hand guard

back toward the front handle as far as

possible.

• When cutting with the saw, the chain brake

must be disengaged.

Disengaged

Braking function control

CAUTION: The chain brake must be

checked several times daily. The engine

must be running when performing this proce-

dure. This is the only instance when the saw

should be placed on the ground with the en-

gine running.

Place the saw on firm ground. Grip the rear

handle with your right hand and the front han-

dle with your left hand. Apply full throttle by

fully depressing the throttle trigger. Activate

the chain brake by turning your left wrist

against the hand guard without releasing

your grip around the front handle. The chain

should stop immediately.

Inertia activating function control

,d_WARNING: When performing the

following procedure, the engine must be

turned off.

G rip the rear handle with your right hand and

the front handle with your left hand, Hold the

chain saw approximately 14 inches (35 cm)

above a stump or other wooden surface. Re-

lease your grip on the front handle and use

the weight of the saw to let the top of the

guide bar fall forward and contact the stump.

When the tip of the bar hits the stump, the

brake should activate.

IMPORTANT POINTS

• Check chain tension before first use and

after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

• Cut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

• Stop the saw if the chain strikes a foreign

object. Inspect the saw and repair or re-

place parts as necessary.

• Keep the chain out of dirt and sand. Even a

small amount of dirt will quickly dull a chain

and thus increase the possibility of kickback.

• Practice cutting a few small logs using the

following techniques to get the "feel" of us-

ing your saw before you begin a major

sawing operation.

• Squeeze the throttle trigger and allow

the engine to reach full speed before

cutting.

• Begin cutting with the saw frame

against the log.

• Keep the engine at full speed the entire

time you are cutting.

• Allowthechaintocutforyou. Exertonly

light downward pressure. If you force

the cut. damage to the bar. chain, or en-

gine can result.

• Release the throttle trigger as soon as

the cut is completed, allowing the en-

gine to idle. If you run the saw at full

throttle without a cutting load, unneces-

sary wear can occur to the chain, bar,

and engine, It is recommended that

the engine not be operated for lon-

ger than 30 seconds at full throttle.

• To avoid Iosh_gcontrol when cut is com-

plete, do not put pressure on saw at end

of cut.

•Stop the engine before setting the saw

down after cutting,

TREE FELLING TECHNIQUES

_WARNING: Check for broken or

dead branches which can fall while cutting

causing serious injury, Do not cut near build-

ings or electrical wires if you do not know the

direction of tree fall, nor cut at night since you

will not be ale to see well, nor during bad

weather such as rain, snow, or strong winds,

etc. If the tree makes contact with any utility

line, the utility company should be notified

immediately.

• Carefully plan your sawing operation in ad-

vance.

• Cleartheworkarea, You needacieararea

all around the tree so you can have secure

footing.

• Study the natural conditions that can cause

the tree to fall in a particular direction,

Natural conditions that can cause a tree to

fall in a particular direction include:

• The wind direction and speed.

• The lean of the tree. The lean of a tree

might not be apparent due to uneven or

sloping terrain, Use a plumb or level to de-

termine the direction of tree lean.

• Weight and branches on one side.

• Surrounding trees and obstacles.

Look for decay and rot, if the trunk is rotted, it

can snap and fall toward the operator. Check

for broken or dead branches which can fall on

you while cutting,

Make sure there is enough room for the tree to

fall, Maintain a distance of 2-1/2 tree lengths

from the nearest person or other objects. En-

gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where cuts are to be

made,

Plan a clear retreat path to the rear and diag-

onal to the line of fail.

p. Plan a clear retreat path

(}--_- Direction of Fall

t45 ° /

FELLING LARGE TREES

(6 inches (15 cm) in diameter or larger)

The notch method is used to fell large trees.

A notch is cut on the side of the tree in the de-

sired direction of fail. After a felling cut is

made on the opposite side of tree, the tree

will tend to fall into the notch.

NOTE: if the tree has large buttress roots,

remove them before making the notch, If us-

ing saw to remove buttress roots, keep saw

chain from contacting ground to prevent dull-

ing of the chain.

NOTCH CUT AND FELLING THE

TREE

• Make notch cut by cutting the top of the

notch first. Cut through 1/3 of the diameter

of the tree. Next compiete the notch by cut-

ting the bottom of the notch, See illustra-

tion. Once the notch is cut remove the

notch of wood from the tree.

Final (felling) cut here, 2 inches

(5 om) above center of notch.

First cut I ,2"; I /

=÷ I/

• After removing the cutout of wood, make

the felling cut on the opposite side of the

notch. This is done by making a cut about

two inches (5 cm) higher than the center of

the notch. This wilt leave enough uncut

wood between the felling cut and the notch

to form a hinge, This hinge will help pre-

vent the tree from falling in the wrong direc-

tion.

Hinge holds tree on stump and helps

control fall Opening

of felling

Closing of

notch

NOTE: Before felling cut is complete, use

wedges to open the cut when necessary to

controI the direction of fall. To avoid kickback

and chain damage, use wood or plastic

wedges, but never steel or iron wedges,

• Be alert to signs that the tree is ready to fall:

cracking sounds, widening of the felling cut,

or movement in the upper branches,

• As tree starts to fall, stop saw, put it down,

and get away quickly on your planned re-

treat path.

• DO NOT cut down a partialIy fallen tree

with your saw. Be extremely cautious with

partially fallen trees that may be poorly

supported, When a tree doesn't fall com-

pletely, set the saw aside and pull down the

tree with a cable winch, block and tacMe,

or tractor.

CUTTING A FALLEN TREE

(BUCKING)

BucMng is the term used for cutting a fallen

tree to the desired log size,

i_ WARNING: Do not stand on the log

being cut. Any portion can roll causing loss

of footing and control. Do not stand downhill

of the log being cut.

IMPORTANT POINTS

•Cut only one _ogat a time.

• Cut shattered wood very carefully; sharp

pieces of wood could be flung toward oper-

ator.

• Use a sawhorse to cut small logs. Never

allow another person to hold the log while

cutting and never hold the log with your leg

or foot,

• Do not cut in an area where logs, limbs,

and roots are tangled such as in a blown

down area. Drag the logs into a clear area

before cutting by pulling out exposed and

cleared logs first,

TYPES OF CUTTING USED FOR

BUCKING

_WARNING: If saw becomes

pinched or hung in a log, don't try to force it

out, You can lose control ofthe saw resulting

in injury and/or damagetothe saw. Stopthe

saw, drive a wedge of plastic or wood into the

cut until the saw can be removed easily. Re-

start the saw and carefully reenter the cut. To

avoid kickback and chain damage, do not

use a metal wedge, Do not attempt to restart

your saw when it is pinched or hung in a log.

,it

411WARNING: Never turn saw upside

down to undercut, The saw cannot be con-

trolled in this position,

Always make your first cut on the compres-

sion side of the log, The compression side of

the log is where the pressure of the log's

weight is concentrated,

First cut on compression side of log

Second cut

First cut on compression side of log

BUCKING WITHOUT A

SUPPORT

•Overcut through t/3 of the diameter of the

log.

• Roll the log over and finish with a second

overout,

• Watch for logs with a compression side to

prevent the saw from pinching, See iF

lustrations for cutting logs with a compres-

sion side.

BUCKING USING A LOG OR

SUPPORT STAND

• Remember your first cut is always on the

compression side of the log,

(Refer to the illustrations below for your

first and second cut)

• Your first cut should extend t/3 of the

diameter of the log,

• Finish with your second cut.

Using alog for support

Turn saw OFF and use a plastic or

wooden wedge to force cut open,

Overcutting begins on the top side of the log

with the bottom of the saw against the log.

When overcutting use light downward pres-

sure,

Overcutting Undercutting I st Out

b_/1st Cut

Undercutting involves cutting on the under-

side of the log with top of saw against the log.

When undercutting use light upward pres-

sure, Hoid saw firmly and maintain control.

The saw will tend to push back toward you, 12

Using a support stand

2 nd Cut k_

/I st Cut

LIMBING AND PRUNING

A(_WARNING: Be alert for and guard

against kickback. Do not allow the moving

chain to contact any other branches or ob-

jects at the nose of the guide bar when limb-

ing or pruning. Allowing such contact can re-

sult in serious injury.

WARNING: Never climb h_to atree

to limb or prune. Do not stand on ladders,

platforms, a log. or h_any position which can

cause you to lose your balance or control of

the saw.

IMPORTANT POINTS

• Work slowly, keeping both hands firmly

gripped on the saw. Maintain secure foot-

ing and balance.

• Watch out for springpoies. Springpoles

are small size limbs which can catch the

saw chah_ and whip toward you or pull you

off balance. Use extreme caution when

cutting small size limbs.

• Be alert for springback. Watch out for

branches that are bent or under pressure.

Avoid being struck by the branch or the

saw when the tension h_the wood fibers is

released.

• Keep a clear work area. Frequently clear

branches out of the way to avoid tripping

over them.

LIMBING

• Always limb a tree after itis cut down. Only

then can limbing be done safely and prop-

erly.

• Leave the larger limbs underneath the

felled tree to support the tree as you work.

• Start at the base of the felled tree and work

toward the top. cutting branches and

limbs. Remove small limbs with one cut.

• Keep the tree between you and the chain.

Cut from the side of the tree opposite the

branch you are cutting.

• Remove larger, supporting branches with

the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

• Always use an overcut to cut small and

freely hanging limbs. Undercutting could

cause limbs to fall and pinch the saw.

PRUNING

_J, WARNING: Limit pruning to limbs

shoulder height or below. Do not cut if

branches are higher than your shoulder. Get

a professional to do the job.

• Make your fist cut I/3 of the way

through the bottom of the limb.

• Next make a 2nd cut all the way

through the limb. Then cut a third

overcut leaving a 1to 2 inch (2.5 - 5 cm)

collar from the truck of the tree.

_ThiPrd! Sec°nd cutoff" _J_

Collar lit_

X_!_ _ First cut

_/ Pruning technique

,I_WARNING: Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

We recommend all service and adjustments

not listed in this manual be performed by an

authorized service dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture levei .... Before each use

Bar lubrication ....... Before each use

Chain tension ....... Before each use

Chain sharpness ..... Before each use

For damaged parts ... Before each use

For loose caps ...... Before each use

For loose fasteners... Before each use

For loose parts ...... Before each use

Inspect and Clean:

Bar ................ Before each use

Complete saw ....... After each use

Air filter ............. Every 5 hours*

Chain brake ......... Every 5 hours*

Spark arresting screen

and muffler .......... Every 25 hours*

Replace spark plug . Yearly

Replace fuel filter ... Yearly

*Hours of Operation -

Each hour of operation is approximately

2 tanks of fuel.

AIR FILTER

CAUTION: Do not clean filter ingasoline

or other flammable solvent to avoid creating

a fire hazard or producing harmful evapora-

tive emissions.

Cleaning the air filter:

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after 10

tanks of fuel or 5 hours of operation, which-

ever comes first. Clean more frequently in

dusty conditions. A used aire filter can never

be completely cteaned, it is advisable to re-

place your air filter with a new one after every

50 hours of operation, or annually, whichever

comes first.

1. Loosen 3 screws on cylinder cover.

2. Remove cylinder cover.

3. Remove air filter.

4. Clean the air filter using hot soapy water.

Rinse with clean cool water. Air dry com-

pletely before reinstalling.

5. Lightly oil air filter before installing to im-

prove the efficiency of air filter. Use

2-cycle engine oil or motor oil (SAE 30).

Squeeze excess oil from filter.

6. Reinstafl air filter.

7. Reinstall cytinder cover and 3 screws.

Tighten securely.

.... /---,_,_,_-- Cylinder

Air l-filer _ _"_._'_...... Cover

C> * °rews

I_'N _'_l/V_<" Cylinder

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

_WARNING: The muffler on this

product contains chemicals known to the

State of California to cause cancer.

As the unit is used, carbon deposits build up

on the muffler and spark arresting screen,

and must be removed to avoid creating afire

hazard or affecting engine performance.

Replace the spark arresting screen if breaks

occur.

CLEANING THE SPARK ARREST-

ING SCREEN

Cleaning is required every 25 hours of op-

eration or annually, whichever comes first.

Outlet

Guide

Backplate Muffler

Gasket

Muffler

/Muffler

_/ Bolts

Bolt Cover Looknut

1. Loosen and remove the Iocknut from the

bolt cover.

2. Remove the bolt cover.

3. Loosen and remove the 2 muffler bolts.

Remove the muffler, muffler gasket, out-

let guide and backplate. Notice the ori-

entation of these parts for reassembling.

4. Locate the 2 outlet cover screws on the

muffler. Loosen and remove both

screws.

5. Remove the outlet cover.

_ Outlet Cover BACK ViEW OF

MUFFLER

Muffler

Screws

Spark Arresting

Screen

Remove spark arresting screen.

Ctean the spark arresting screen with a

wire brush. Replace screen ifany wires are

broken or screen is blocked after cleaning.

Reinstall spark arresting screen.

Reinstall outlet cover and 2 screws. En-

sure outlet cover and both screws are re-

installed correctly (see illustrations) to

prevent damage to the saw. The exhaust

outlet must face the chain brake (bar

side) of the saw. Outlet Cover

Exhaust _,. _/

Outlet

Exhaust Outlet must face chain

brake (bar side) of chain saw

10. inspect the muffler gasket and replace if

damaged.

11. Reinstall backplate, outlet guide, muffler

gasket, and muffler using muffler bolts.

Tighten until secure.

12. Reinstall bolt cover and Iocknut. Tighten

securely.

CARBURETOR ADJUSTMENT

_1= WARNING : The chain will be mov-

ing during most of this procedure, Wear your

protective equipment and observe all safety

precautions, The chain must not move at idle

speed.

The carburetor has been carefully set at the

factory. Adjustments may be necessary if

you notice any of the following conditions:

•Chain moves at idle. See iDLE SPEED-T

adjusting procedure.

• Saw will not idle. See IDLE SPEED-T ad-

justing procedure.

Idle Speed-T

Allow engine to idle. if the chain moves, idle

is too fast. If the engine statls, idle is too slow.

Adjust speed until engine runs without chain

movement (idle too fast) or statling (idle too

slow). The idle speed screw is located in the

area above the primer bulb and is labeled T.

• Turn idle speed screw (T) clockwise to in-

crease engine speed.

• Turn idle speed screw (T) counterclock-

wise to decrease engine speed.

If you require further assistance or are unsure

about performing this procedure, contact your

authorized service dealer or call

1-800-554-6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut. or been run with an improper

amount of bar lubrication it may be necessary

to service your bar. A worn bar will damage

your chain and make cutting difficult.

After each use. ensure ON/STOP switch is in

the STOP position, then clean all sawdust from

the guide bar and sprocket hole.

To maintain guide bar:

• Move ON/STOP switch to the STOP posi-

tion.

• Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

• Clean the oil holes and bar groove affer each

5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

• Burring of guide bar rails is a normal process

of rail wear. Remove these burrs with a flat

file.

• When rail top is uneven, use a flat file to re-

store square edges and sides.

_j"_ File Rail Edges_ ['] r]

and Sides IUI

square [ ]

Worn Groove Correct Groove

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when exce-

ss heating or burring of the rails occurs. If re-

placement is necessary, use only the guide bar

specified for your saw in the repair parts list or

on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that

requires special tools. We recommended

you refer chain sharpening to a professional

chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better.

1. Loosen 3 screws on cylinder cover.

2. Remove the cylinder cover.

3. Pull off the spark plug boot.

4. Remove spark plug from cylinder and dis-

card.

5. Replace with Champion RCJ-7Y spark

plug and tighten securely with a 3/4 inch

(19 mm) socket wrench. Spark plug gap

should be 0.025 inch (0.6 mm).

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3 screws.

Tighten securely.

Screws Cover

Plug Boot

Spark

Plug

STORAGE

_' WARNING :stop engine and allow

to cool, and secure the unit before storing or

transporting in a vehicle. Store unit and fuel

in an area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

Store unitwith all guards in place. Position so

that any sharp object cannot accidentally

cause injury to passersby. Store the unit out

of reach of children.

• Before storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

• Clean the unit before storing. Pay particu-

lar attention to the air intake area, keeping

it free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

• Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

• Store in a dry area out of the reach of chil-

dren.

CAUTION: It is important to prevent gum

deposits from forming in essential fuel system

parts such as the carburetor, fuel filter, fuel

hose, or fuel tank during storage. Alcohol

blended fuels (called gasohol or using ethanol

or methanol) can attract moisture which leads

to fuel mixture separation and formation of

acids during storage. Acidic gas can damage

the engine.

NEED ASSISTANCE?

Call t-800-554-6723.

NEED SERVICE PART?

Contact your authorized service dealer.

TROUBLESHOOTING TABLE

_b, WARNING: Always stop unit and disconnect spark plug before performing all of

the recommended remedies below except remedies that require operation of the unit,

TROUBLE REMEDY

Engine will not

start or will run

only a few

seconds after

starting.

CAUSE

1. ignition switch off,

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. FueI not reaching

carburetor.

1. Move ignition switch to ON.

2. See "Difficult Starting" in

Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

1. See "Carburetor Adjustment" in the

Service and Adjustments Section.

2. Contact an authorized service dealer.

Engine will 1. Carburetor requires

not idle adjustment.

properly. 2. Crankshaft seals worn.

Engine will not 1. Air filter dirty. 1. Clean or repIace air filter.

accelerate, 2. Spark plug fouled. 2. Clean or replace plug and regap.

lacks power. 3. Chain brake engaged. 3. Disengage chain brake.

or dies under 4. Carburetor requires 4. Contact an authorized service dealer.

a load. adjustment.

Engine 1. Too much oil mixed with 1. Empty fuel tank and refill with

smokes gasoline, correct fuel mixture.

excessively.

Chain moves 1. Idle speed requires 1. See "Carburetor Adjustment" in the

at idle speed, adjustment. Service and Adjustments Section.

2. Clutch requires repair. 2. Contact an authorized service dealer.

Poulan PRO warrants to the original pur-

chaser that each new Poulan PRO brand

gasoline chain saw is free from defects in

material and workmanship and agrees to re-

pair or replace under this warranty any de-

fective gasoline chain saw as follows from

the original date of purchase,

2 YEARS = Parts and Labor, when used for

Household purposes.

60 DAYS - Parts and Labor, when used for

Commercial, Professional, or Income Pro-

ducing purposes,

30 DAYS - Parts and Labor, if used for rental

purposes,

This warranty is not transferable and does

not cover damage or liability caused by im-

proper handling, improper maintenance, or

the use of accessories and/or attachments

not specifically recommended by Poulan

PRO for this chain saw, Additionally, this

warranty does not cover damage caused by

improper handling, improper maintenance,

or if the saw is altered in any way which in our

judgement affects its condition or operation.

This warranty does not cover tune-up, spark

plugs, filters, starter ropes, starter springs,

chain sharpening, bars, chains, and other

parts which wear and require replacement

with reasonable use during the warranty pe-

riod, This warranty does not cover predeliv-

ery set-up, installation of guide bar and

chain, and normal adjustments explained in

the instruction manual such as carburetor

adjustments and chain tension adjustments.

This warranty does not cover transportation

costs.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EXPRESS-

LY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS OR EXCLUSION MAY NOT

APPLY TO YOU.

The policy of Poulan PRO is to continuously

improve its products, Therefore, Poulan

PRO reserves the right to change, modify, or

discontinue models, designs, specifications,

and accessories of all products at any time

without notice or obligation to any purchaser.

YOUR WARRANTY RIGHTS AND OBLIGA-

TIONS: The U,S. Environmental Protection

Agency, California Air Resources Board, Envi-

ronment Canada and Poulan/WEED EATER

are pleased to explain the emissions control

system warranty on your year 2005 and later

small off-road engine. In California, all small

off-roed engines must be designed, built, and

equipped to meet the State's stringent anti-

smog standards. PoulanANEED EATER must

warrant the emission control system on your

small off-toed engine for the periods of time

listed below provided there has been no abuse,

neglect, or improper maintenance of your small

off-roed engine. Your emission control system

includes parts such as the carburetor and the

ignition system, Where a warrantable condition

exists, PoulanNVEED EATER will repair your

small off-road engine engine at no cost to

you. Expenses covered under warranty in-

clude diagnosis, parts and labor,

MANUFACTURER'S WARRANTY COV-

ERAGE: If any emissions re_ated part on

your engine (as listed under Emissions Con-

trol Warranty Parts List) is defective or a de-

fect in the materials or workmanship of the

engine causes the failure of such an emis-

sion related part, the part will be repaired or

replaced by PoulanANEED EATER. OWN-

ER'S WARRANTY RESPONSIBILITIES:

As the small off-road engine engine owner,

you are responsible for the performance of the

required maintenance listed in your instruction

manual. Poulan/WEED EATER recommends

that you retain all receipts covering mainte-

nance on your small off-road engine, but Pou-

Ian/WEED EATER cannot deny warranty sole-

ly for the tack of receipts or for your failure to

ensure the performance of all scheduled main-

tenance. As the small off-road engine engine

owner, you should be aware that Poulan/

WEED EATER may deny you warranty cover-

age if your small off-road engine engine or a

part of it has failed due to abuse, neglect, im-

proper maintenance, unapproved modifica-

tions, or the use of parts not made or approved

by the original equipment manufacturer. You

are responsible for presenting your small off-

road engine to a Poulan/WEED EATER autho-

rized repair center as soon as a problem exists.

Warranty repairs should be completed in a rea-

sonable amount oftime, not to exceed 30 days.

If you have any questions regarding your war-

ranty rights and responsibilities, you should

contact your nearest authorized service center

or call Poulan/WEED EATER at

1-800-554-6723. WARRANTY COM-

MENCEMENT DATE: The warranty period

begins on the date the small off-roed engine is

purchased. LENGTH OF COVERAGE: This

warranty shall be for a period of two years from

the initial date of purchase.

WHAT IS COVERED: REPAIR OR RE-

PLACEMENT OF PARTS. Repair or replace-

ment of any warranted part will be performed at

no charge to the owner at an approved Poulan/

WEED EATER servicing center. If you have

any questions regarding your warranty rights

and responsibilities, you should contact your

nearest authorized service center or call

Poulan/WEED EATER at 1-800-554-6723.

WARRANTY PERIOD: Any warranted part

which is not scheduled for replacement as

required maintenance, or which is scheduled

only for regular inspection to the effect of "repair

or replace as necessary" shaII be warranted for

2 years. Any warranted part which is sched-

uled for replacement as required maintenance

shall be warranted for the period of time up to

the first scheduled replacement point for that

part. DIAGNOSIS: The owner shall not be

charged for diagnostic labor which leads to the

determination that a warranted part is defective

if the diagnostic work is performed at an ap-

proved Poulan/WEED EATER servicing cen-

ter. CONSEQUENTIAL DAMAGES: Poulan/

WEED EATER may be liable for damages to

other engine components caused by the failure

of a warranted part still under warranty. WHAT

IS NOT COVERED: All failures caused by

abuse, neglect, or improper maintenance are

not covered. ADD-ON OR MODIFIED

PARTS: The use of add-on or modified parts

can be grounds for disallowing a warranty

claim. Poulan/WEED EATER is not liable to

cover failures of warranted parts caused by the

use of add-on or modified parts. HOW TO

FILE A CLAIM: If you have any questions re-

garding your warranty rights and responsibili-

ties, you should contact your nearest autho-

rized service center or call PoulanANEED

EATER at 1-800-554-6723. WHERE TO

GET WARRANTY SERVICE: Warranty ser-

vices or repairs shall be provided at all Poulan/

WEED EATER service centers. Call:

1-800-554-6723 MAINTENANCE, RE-

PLACEMENT AND REPAIR OF EMIS-

SION RELATED PARTS: Any Poulan/

WEED EATER approved replacement part

used in the performance of any warranty

maintenance or repair on emission related

parts will be provided without charge to the

owner ifthe part is under warranty. EMISSION

CONTROL WARRANTY PARTS UST: Car-

buretor. Ignition System: Spark Plug (covered

up to maintenance schedule), Ignition Module,

Muffler including catalyst. MAINTENANCE

STATEMENT: The owner is responsible for the

performance of all required maintenance as

defined in the instruction manual.

The information on the product label indicates which standard your engine is certified,

Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

[] Moderate (50 hours)

[] Intermediate (125 hours)

[] Extended (300 hours)

F_l,,,,3Jf_

ADVERTENClA: iEsta

sierra de cadena puede ser

peligrosa! El uso descuidado

o indebido de esta herramienta

puede causar graves heridas.

D Lea y comprenda el

manual de instruc-

clones antes de usar la

sierra.

Use siempre la proteccion de oidos apropiada, Ia proteccion de

ojos y la protecci6n de la cabeza.

Use siempre las dos manes cuando trabaje con ia sierra de

cadena.

ADVERTENClA: Debe evitarsecualquier contactode

la punta de la barra guia con cualguier objeto, ya que puede

causar que la barra guia se desplace repentinamente hacia

arriba y hacia atr&.s, con posibles graves heridas.

Maximo valor de kickback medido sin eI freno de cadena para la

combinaci6n de barra y cadena indicada en la etiqueta.

_ ADVERTENClA: Desconecte

siempre el cable de la bujia y col6quelo

donde no puede entrar en contacto con el

bujia, para evitar cualquier arranque acci-

dental al preparar, transportar, ajustar o re-

parar el aparato, excepto en el caso de

ajustes al carburador.

Debido a que las sierras de cadena son

instrumentos para cortar madera a alta velo-

cidad, deben observarse precauciones de

seguridad especiales para reducir el riesgo

de accidentes. El uso descuidado o indebi-

do de esta herramienta puede causar

graves heridas.

PIENSE ANTES DE PROCEDER

• Antes de utilizar la sierra, lea attentamente

este manual hasta estar seguro o compren-

dedo completamente y poder seguir todas

las reglas de seguddad, precauci6ns e

instrucciones de uso que se dan en et.

• Umite el uso de la sierra a aqueilos usuarios

adultos que comprendad y puedan imple-

mentar todas las precauciones, regtas de

seguridad e instrucciones de uso que se en-

cuentran en este manual.

Proteccion Casco Duro

de Oi._s _ Proteccidn de

"_ i=,_i* "I ojos

Ropa Ajustada

al Cuerpo _ Guantes de

Uso Industria

Zapatos de Pantorfilteras

Seguridad uridad

""%,,I --

Use equipo protector. Siempre use calzado

de seguridad con puntas de acero y suelas

anti-deslizantes; ropa ajustada el cuerpo;

guantes gruesos de uso industrial anti-desli-

zantes; protecci6n de ojos tales como gafas

de seguridad que no se empa[_an y con ab-

erturas de ventiltacion o mascara protectora

para la cara; casco duro aprobado; y barrera

de sonido (tapones de oido u orejeras anti-

sonido) para proteger la audicion. Los que

usan sierras de fuerza deber#tn hacerse re-

visar la audici6n frecuentemente ya que el

ruido de tas sierras de cadena puede daSar

los oidos.

• Mantenga todas las partes del cuerpo ateia-

das de la cadena siempre que el motor este

en funcionamiento.

• Maetenga a los nifios, espectadores y ani-

males a una distancia minima de 10 metros

(30 pies) del Area de trabajo o cuando esta

hacieeco arrancar el motor,

• No levante ni opere la sierras de cadena

cuando esta faigado, enfermo, ansioso o si

ha tornado alcohol, drogas o remedios. Es

imprescindible que ed. este en buenas con-

diciones fisicas y alerta mentalmente, Si ud.

sufre de cualquier condicion que pueda em-

peorar con el trabajo arduo, ases6rese con

su m6dico.

• No ponga en marcha ta sierra sin tener un

Area de trabajo despeiada, superficie est-

able para pararse y, si esta derrubando

arboles, un camino predeterminado de retro-

ceso,

USE LA SIERRA OBSERVANDO

TODOS LOS PROCEDIMIENTOS

DE SEGURIDAD

•Mantenga las dos manos en las maeijas

siempre que el aparato este en marcha. El

uso del aparato con una sola mano puede

causar graves heridas al usuario, a los asis-

tentes, o a los espectadores, Las sierras de

cadena estan disefiadas para que se las use

con las dos manos en todo mornento,

• Haga uso de la sierra de cadena Qnicamente

en lugares exteriores bien ventillados,

• No haga uso de la sierra desde las escaler-

as portatiles ni de los arboles.

• AsegQrese de que la cadena no vaya a hac-

er contacto con ningOn objeto antes de pon-

er en marcha el motor, Nunca intente hacer

arrancar la sierra con la barra quia ee un

corte.

• No aplique presi6n a la sierra al final de los

cortes. Apiicar presi6n puede hacer que

pierda el control al completarse el corte,

• Pare el motor antes de apoyar la sierra en

ningQn lado,

• No ponga en funcionamiento ta sierra de ca-

dena si esta dafiada, incorrectamente ajus-

tada, o si no esta armada completa y segu-

ramente. Siempre cambie el protector de

mano immediatamente si esta queda da(_a-

do, roto, o se sale por cualquier motivo,

• Cuando cargue la sierra de cadena en las

manos, hagalo con et motor parado, el silen-

ciador alejado del cuerpo, y la cadena hacia

atras y cubierta con ue estuche,

MANTENGA LA SIERRA EN BUE-

NAS CONDICIONES DE FUNC-

TIONAMIENTO

• Ueve la sierra de oadena a un distribuidor

autorizado del servicio para que haga todo

servicio menos aquellos procedimientos lis-

tados en ta secci6n de mantenimiento de

este manual. Por ejempplo, si se usan her-

ramientas que no corresponden para retirar

o sostener el volante at hacer servicio al em-

brague, pueden ocurrir dafios estructurates

at volante y causar que reviente.

• AsegOrese de que la cadena se detenga por

compIeto cuando se suelta el gatillo. Para

hacer correcciones, yea los AJUSTES AL

CARBURADOR.

•Nunca haga modificaciones de ninguna in-

dole a su sierra.

• Mantenga las manijas secas, limpias y libres

de aceite o de mezcia de combustible,

• Mantenga las tapas y los fijadores blen fijos.

• Use exclusivamente los accesorios y re-

puestos Poulan PRO recomendados,

MANEJE EL COMBUSTIBLE CON

EXTREMO CUIDADO

• No fume mientras trabaja con el combustible

ni cuando esta haciendo uso de la sierra.

• EHmine todas las posibles fuentes de chis-

paso llamas en las Areas donde se mezclao

vierte el combustible. No debe haber el fu-

mar, llamas abiertas, o trabajo que podria

causar chispas, Permita que el motor es frio

antes de reaprovisionar de combustible,

• Mezcte y vierta et combustible afuera y use

recipiente aprobado para combustibles y

marcado como tal. Umpie todos los der-

tames de combustible,

• Alejese a por Io mendos 3 metros (10 pies)

del lugar de abastecimiento antes de poner

el motor en march&

• Apague el motor y deje que la sierra se

enfrie en un lugar libre de substancias com-

bustibles y no sobre hojas secas, paja, pa-

pel, etc. Retire latapa Ientamente y reabas-

tezca el aparato,

• Guarde el aparato en un espaciuo fresco,

seco y bien ventilado donde los vapores del

combustible no pueden entrar en contacto

con chispas ni llamas ablertas provenientes

de termotaegues, motores o interruptores

electricos, calefactores centrales, etc.

RECULADA

_b ADVERTENCIA: Evite reculada le

pueden causar graves heridas. Reculada

es eI movimiento hacia et frente, hacia atras

o rapidamente hacia adelante, esto puede

ocurrir cuando la punta de la barra guia de la

sierra de oadena entra en oontaoto con ouaF

quier objeto como puede ser otra rama o

tronco, o ouando la madera se cierra y atas-

ca mientras se hace el corte. El entrar en

coetacto con algLin objeto extra(_o a la mad-

era le puede causar al usuario la perdida del

controI de la sierra de cadena.

• La Reculada Rotacional puede aconteoer

ouando la oadena en movimiento entra en

contacto con algOn objeto en la parte superi-

or de la punta de la barra guia puede causar

que la cadena entre al material y se detenga

por un instante. El resultado es una reacci6n

inversa, a velocidad de relarnpago, que hace

recular la barra guia hacia arriba y hacia

atras hacia el usuario.

• La Reculada por Ataaco acontecen cuan-

do la madera se cierra y atasca la cadena en

movimiento en el corte a Io largo de la parte

superior de la barra guia y la cadena se de-

tiene repentinamente. Esta detenci6n re-

pentina de la cadena tiene como resuItado

una inversi6n de ta fuerza de la cadena usa-

da para cortar madera y causa que lasierra

se mueva en sentido opuesto al de la rota-

La page charge ...

Poulan Pro SM4018 Manuel utilisateur

Marque: Poulan Pro

Modèle: SM4018

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Poulan Pro SM4018 User manual
español: Poulan Pro SM4018 Manual de usuario

Poulan Pro SM4018 Manuel utilisateur

Poulan Pro SM4018 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents