PowerSmart PS76402C Manuel utilisateur

INSTRUCTION MANUAL

EN 40V Cordless Blower

FR Souffleur sans fil 40V

ES Soplador Inalámbrico 40V

Model # PS76220A

Have product questions or need technical support? Please feel free to contact us!

Website: www.powersmartusa.com

Toll free: 1-800-791-9458 M-F 9-5 EST

Email: [email protected]

2

3

CONTENTS

Technical data …...……………………………………………………… 3

Introduction …...………………………………………………………... 4

Safety information …...………………………………………………… 4

General safety rules…….………………………………………….…… 5

Special safety rules for cordless blower………………………………… 7

Symbols …...………………………………………………………......... 8

Knowing your cordless blower.……………….….……………………… 9

Assembly instruction…………………………………………….………. 10

Operating instruction…………………………………………………....... 12

Maintenance……………………………………………………...………. 13

Trouble shooting…………………………………………………………. 14

Exploded view…………………………………………………………… 15

Parts list…………………………………………………………………... 16

Warranty…………………………………………………………………. 17

TECHNICAL DATA

40V Cordless Blower Model # PS76220A

Power input: 40V

No-load speed: 17500 RPM±10%

Max air speed: 120 MPH

Max wind capacity: 450 CFM

Battery type: 40 V Lithium-ion, 4Ah

Battery model: DB2102

Charging time: 150 minutes

Charger model: DB2202A

Weight: 11 lb.

EN

4

INTRODUCTION

Thank You for Purchasing a PowerSmart® Product. This manual provides information regarding the safe

operation and maintenance of this product. Every effort has been made to ensure the accuracy of the

information in this manual. PowerSmart® reserves the right to change this product and specifications at

any time without prior notice.

Please keep this manual available to all users during the entire life of the power tool.

This manual contains special messages to bring attention to potential safety concerns, power

tool damage as well as helpful operating and servicing information. Please read all the

information carefully to avoid injury and machine damage.

QUESTIONS? PROBLEMS?

Please contact our Customer Service Dept. with any questions and/or comments, either by email:

[email protected], or Toll Free at (800)791-9458. We are available Mon-Fri 9am-5pm EST to

help solve any issues that you might encounter.

SAFETY INFORMATION

Before operating this power tool, read and observe all warnings, cautions, and instructions on the power

tool and in this Owner’s Manual.

NOTE: The following safety information is not meant to cover all possible conditions and situations that

may occur. Read the entire Owner’s Manual for safety and operating instructions. Failure to follow

instructions and safety information could result in serious injury or death.

This safety alert symbol is used to identify safety information about hazards that can result in personal

injury.

A signal word (DANGER, WARNING, or CAUTION) is used with the alert symbol to

indicate the likelihood and the potential severity of injury. In addition, a hazard symbol may

be used to represent the type of hazard.

DANGER Indicates a hazard, which, if not avoided, will result in death or serious injury.

WARNING Indicates a hazard, which, if not avoided, could result in death or serious injury.

CAUTION Indicates a hazard, which, if not avoided, might result in minor or moderate injury.

CAUTION Without the alert symbol, indicates a situation that could result in damage.

5

GENERAL SAFETY RULES

Safety is a combination of common sense, staying alert, and knowing how your power tool works.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING: Do not operate this unit until you read this instruction manual for safety,

operation and maintenance instructions. Failure to follow all instructions listed below may

result in electric shock, fire, and/or serious personal injury.

WORK AREA SAFETY

 Keep your work area clean and well lit, cluttered benches and dark areas invite accidents.

 Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,

gases, or dust. Power tools create sparks which may ignite the dust or fumes.

 Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause

you to lose control.

ELECTRICAL SATETY

 Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk

of electric shock.

 Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

 Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

 Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

 When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

 If operating a power tool in a damp location is unavoidable, use a ground fault circuit.

PERSONAL SAFETY

 Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use

a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of

inattention while operating power tools may result in serious personal injury.

 Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or

hearing protection must be used for appropriate conditions.

 Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing,

and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving

parts.

 Avoid accidental starting. Be sure switch is off before connecting to power source and/ or battery

pack, pick up or carrying the tool. Carrying power tools with your finger on the switch or energizing

power tools that have the switch on invites accidents.

 Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

 Do not overreach. Always keep proper footing and balance. Proper footing and balance enable better

control of the power tool in unexpected situations.

 If devices are provided for the connection of dust extraction and collection facilities, ensure theses

are connected and properly used. Use of dust collection can reduce dust-related hazards.

6

POWER TOOL USE AND CARE

 Do not force power tool. Use the correct power tool for your application. The correct power tool will

do the job better and safer at the rate for which it is designed.

 Do not use the power tool if switch does not turn it on or off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

 Disconnect the plug from the power source before making any adjustments, changing accessories, or

storing the power tool. Such preventive safety measures reduce the risk of starting the power tool

accidentally.

 Store idle power tools out of reach of children and other untrained persons. Power tools are

dangerous in the hands of untrained users.

 Maintain power tools with care. Keep cutting tools sharp and clean. Properly maintained power tools,

with sharp cutting edges are less likely to bind and are easier to control.

 Check for misalignment or binding of moving parts, breakage of parts, and any other condition that

may affect the power tools operation. If damaged, have the power tool serviced before using.

 Use the power tool, accessories, and tool bits etc. in accordance with these instructions, taking into

account the working conditions and the work to be performed. Use of the power tool for operations

different from those intended could result in a hazardous situation.

 Save these instructions. Refer to them frequently and use them to instruct others who may use this

tool. If you lend this tool to someone else, also lend them these instructions.

BATTERY TOOL USE AND CARE

 Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

 Use power tools only with specifically designated battery packs. Use of any another battery packs

may create a risk of injury and fire. Use only POWERSMART battery (Model#DB2102)

 When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or a fire.

 Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact

with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If

liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate

medical attention. Following this rule will reduce the risk of serious personal injury.

SERVICE

 Tool service must be performed only by qualified repair personnel. Service or maintenance

performed by unqualified personnel could result in a risk of injury.

 When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance

section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may

create a risk of electric shock or injury.

7

SPECIFIC SAFETY RULES FOR CORDLESS BLOWER

 Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,

hair, and anything that may reduce air flow.

 Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

 Use extra care when cleaning on stairs.

 Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they

may be present.

 Remove all hard objects from work area. Do not blow debris in the direction of people, animals, or

property.

 Use only accessories provided. Keep guards in place and in working order.

 Maintain labels and nameplates on the appliance. These carry important safety information.

 People with pacemakers should consult their physician(s) before use. Electromagnetic fields near

heart pacemaker could cause pacemaker interference or pacemaker failure.

 The warnings, precautions, and instructions discussed in this instruction manual cannot cover all

possible conditions and situations that may occur. It must be understood by the operator that

common sense and caution are factors which cannot be built into this product but must be supplied

by the operator.

8

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL

NAME

DESIGNATION/EXPLANATION

V

Volts

Voltage

A

Amperes

Current

Hz

Hertz

Frequency (cycles per second)

W

Watts

Power

min

Minutes

Time

Safety Alert

Precautions that involve your safety.

Read the user’s

manual

To reduce the risk of injury, user must read and understand user’s

manual before using this product.

Eye protection

Wear eye protection that is marked to comply with ANSI Z87.1 when

operating this equipment.

Wet conditions

alert

Do not expose to rain or use in damp locations.

Long hair

Failure to keep long hair away from the air inlet could result in personal

injury.

Loose clothing

Failure to keep loose clothing from being drawn into air intake could

result in personal injury.

Keep Bystanders

away

Keep all bystanders at least 50 ft. away.

Blower tubes

Do not operate without tubes in place.

Electric shock

alert

Beware of electric shock hazard.

9

KNOWING YOUR CORDLESS BLOWER

Unpacking

Unpack the power tool and all its parts and compare against the list below. Do not discard the carton or

any packaging materials. Please call 1-800-791-9458 or e-mail us at [email protected] if any

parts are damaged or missing.

Including: Cordless blower/ Blower tube mouth/Blower tube / Battery / Charger / User manual

1

Blower Tube Mouth

2

3

4

5

Blower Tube

Turbo Button

ON/OFF Trigger Switch

Battery

6

Charger

6

10

ASSEMBLY INSTRUCTION

WARNING:

Do not use this product if any parts on the packing list are already assembled to your product

when you unpack it. Parts on this list are not assembled to the product by the manufacturer

and require customer installation. Use of a product that may have been improperly assembled

could result in serious personal injury.

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced.

Use of this product with damaged or missing parts could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create accessories not recommended for use with

this product. Any such alteration or modification is misuse and could result in a hazardous

condition leading to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result in

accidental starting and possible serious personal injury.

INSTALLING THE BLOWER TUBE

WARNING: Always ensure that the tool is switched off and the battery is removed before

making any adjustments or maintenance procedures.

1. Rotate blower tube mouth in place in the direction of arrow.

2. Check the blower tube mouth is firmly secured.

3. Insert the blower tube to the motor housing in the direction of arrow.

4. Rotate blower tube in place in the direction of arrow.

5. Check the blower tube is firmly secured.

Fig.1

11

REMOVING THE BLOWER TUBE

1. Turn blower tube in the direction of arrow 1, so that you can separate the tube.

2. Remove tube in the direction of arrow 2. Do not try to separate the tubes by force or by using tools.

Note: Before disassembling the Blower Tube, be sure the ON/OFF trigger switch is on off position.

CONNECTING AND REMOVING BATTERY

IMPORTANT!

The battery pack is not charged when it is purchased. Before using the power tool for the first time, place

the battery pack in the battery charger and charge. Make sure to read all safety precautions and follow the

instructions in the battery charger section.

To install the battery pack

To install the battery pack into the bottom of the blower, align the rails of the battery pack with the rails in

the blower and push the battery into the blower. To connect the battery, slide the battery pack fully

forward. Until the latch locks into place.

To remove the battery pack

Press the battery release button, Slide the battery pack backward, and then pull or lift the battery out of

the tool.

WARNING:

Follow these instructions to avoid injury and to reduce the risk of electric shock or fire:

• Replace the battery pack or the charger immediately if the battery case or charger cord is damaged.

• Verify that the battery pack is removed before inspecting, adjusting, or performing maintenance on

any part of the power tool.

• Read, understand, and follow the instructions.

Fig.2

12

OPERATING INSTRUCTION

Turbo button

A function of increase in airflow “turbo”, is used only on occasions when leaves and trash is stuck or

when the normal airflow is not sufficient. In most cases, normal airflow is sufficient. An increase in

airflow is used mainly for brief measures.

Switching On/Off

Hold the blower with one hand on the control handle - wrap your

thumb around the handle.

Pull the trigger with your index finger and hold it there. The

blower accelerates and air flows from the nozzle.

To switch off, release the On/Off trigger switch. No air flows from

the nozzle.

Using the Blower

Holding and Controlling the Blower

Hold and control the blower with one hand on the control handle - wrap your thumb around the handle.

Point the nozzle at the ground, walk slowly and steadily forwards.

TEMPERATURE CONTROL /OVERLOAD PROTECTION

When the temperature of battery is too high, and the machine switches off automatically.

• Switch the power tool off.

• Allow the battery to cool down before continuing to work.

When the power tool is blocked and switches off automatically.

• Remove the power tool from the workpiece.

• As soon as the blockage is corrected, the tool will continue to work at the set stroke rate.

IMPORTANT CHARGING NOTES

WARNING: Battery packs are shipped in a low charge condition to prevent possible

problems. Therefore, you should charge them before first use.

• Use only POWERSMART battery charger (Model#DB2202A)

• Charge time is approximately 90 minutes and is dependent upon the type of battery pack.

• Make sure the power supply is normal household voltage, 120V, AC only, 60Hz.

• Attach the battery pack to the charger by aligning the raised ribs on the battery pack with the grooves

in the charger, then slide the battery pack onto the charger.

• Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts

in the charger. Latches should snap into ensure charger is correctly connected.

• Do not place the charger in an area of extreme heat or cold. It will work best at normal room

temperature.

• The battery pack may become slightly warm to the touch while charging. This is normal and does not

indicate a problem.

• The red LEDs will flash while charging.

• When the green LEDs is light, this indicates the battery is fully charged.

• To remove the battery pack from the charger, depress latches and pull up on the battery pack.

• When the battery pack is fully charged, remove it from the charger.

Turbo button

On/Off trigger switch

Fig.3

13

MAINTENANCE

WARNING: To avoid personal injury and the risk of fire and electric shock, remove the

battery pack before adjusting, inspecting, or cleaning the power tool.

WARNING: When servicing, use only identical replacement parts. Use of any other parts

could create a hazard or cause product damage.

 Be alert for battery packs that are nearing their end of life. If you notice decreased tool performance

or significantly shorter running time between charges, then it is time to replace the battery pack.

Failure to do so can cause the tool to operate improperly or damage the charger.

 Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt

to clean by inserting pointed objects through opening.

 Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from

various types of commercial solvents and may be damaged by their use. Use clean clothes to remove

dirt, oil, grease, etc.

 Our machines have been designed to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon proper machine care and regular

cleaning.

 To maintain battery capacity, we recommend the battery to be completely discharged every one

month and fully recharged again. Only store with a fully charged battery and top-up the charge from

time to time if stored for a long time. Store in a dry and frost-free place, the ambient temperature

should not exceed 60°C（140 ℉）.

14

TROUBLE SHOOTING

WARNING: Read instruction manual first! Remove battery pack from the tool before adjusting

or assembling accessories.

Problem

Possible Cause

Possible Solution

Unit will not start

Battery pack not installed

properly

Check battery pack installation.

Battery pack not charged.

Check battery pack charging

requirements.

Battery pack will not charge.

Battery pack not inserted into

charger.

Insert battery pack into charger

until LED appears

Charger not plugged in

Plug charger into a working

outlet.

Refer notes “for more

details.

Surrounding air temperature too

hot or too cold

Move charger and battery to a

surrounding air temperature of

above 32 degrees F(0°C) or

below 104 degrees F(+40°C)

Unit shuts off abruptly

Battery pack has reached its

maximum thermal limit.

Allow battery pack to cool down

Out of charge. (To maximize the

life of the battery pack, it is

designed to shutoff abruptly

when the charger is depleted

Place on charger and allow to

charge

15

EXPLODED VIEW

16

PARTS LIST

Item

Sku#

Description

Qty

1

203050671

Blower Tube Mouth

1

2

203050672

Blower Tube

1

3

203050673

Brush air duct holder

1

4

203021430

Brushed fairing

1

5

301030091

36V brushed motor

1

6

203021266

Charger insert bracket

1

7

303160888

Motor link sleeve

1

8

306040046

Motor PC board

1

9

306040047

Switch lead

1

10

203021431

Left casing

1

11

203021432

Switch trigger 2

1

12

301100063

Micro Switch

2

13

203021433

Brush motor mounting seat

1

14

303010367

Screw M4×10

2

15

203021422

Shift knob

1

16

303070945

Button spring

1

17

203021434

Blades

1

18

203021435

Right casing

1

19

303010387

Screw M5×14

1

20

203050674

Suction canal

1

21

203050675

Rear cover

1

22

303010325

Screw ST4.2*14mm

16

23

202460015

Battery

1

24

202470011

Charger

1

17

THREE (3) YEARS LIMITED WARRANTY

PowerSmart® is committed to building tools that are dependable for years. Our warranties are consistent with our commitment

and dedication to quality.

THREE (3) YEARS LIMITED WARRANTY OF POWERSMART PRODUCTS FOR HOME USE.

PowerSmart (“Seller") warrants to the original purchaser only, that all PowerSmart consumer power tools will be free from

defects in material or workmanship for a period of three (3) years from date of purchase. Ninety (90) days for all PowerSmart

Products, if the tool is used for professional or commercial use.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Three (3) Years Limited Warranty and, to the

extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge,

which are defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by

persons other than Seller or Authorized Service Center. To make a claim under this Limited Warranty, you must return the entire

power tool product; transportation prepaid, to PowerSmart Include a legible copy of the original receipt, which lists the date of

purchase (month and year) and the name of the company purchased from.

THIS LIMITED WARRANTY DOES NOT APPLY TO ANY ACCESSORY ITEMS INCLUDED WITH THE TOOL SUCH AS

CIRCULAR SAW BLADES OTHER RELATED ITEMS OR TO ANY REPLACEMENT PARTS LISTED UNDER

MAINTENANCE.

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO THREE (3) YEARS FROM DATE OF PURCHASE.

SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT

NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME

STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH

VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO

COUNTRY.

For questions / comments, technical assistance or repair parts –

Please call customer service at: 1-800-791-9458 (M-F 9am – 5pm EST)

Email: [email protected]

SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.

18

TABLE DES MATIÈRES

Données techniques …...…………………………………………..................18

Introduction …...……………………………………………………….........19

Informations sur la sécurité …...……………………………………..............19

Règles générales de sécurité…….…………………………………………....20

Règles de sécurité spécifiques pour le souffleur sans fil………………..…....22

Symboles …...……………………………………………………….............23

Connaître votre souffleur sans fil .……………….….………………….……24

Instruction de montage……………………………………………….............25

Instruction de fonctionnement…………………………………………….....27

Maintenance…………………………………………………….....................28

Dépannage…………………………………………………………. ..............29

Vue explosée…………………………………………………………............30

Liste des pièces…………………………………………………………….....31

Garantie…………………………………………………………………. ......32

DONNÉES TECHNIQUES

Souffleur sans fil 40V Modèle # PS76220A

Alimentation électrique: 40V

Vitesse à vide: 17500 RPM±10%

Vitesse maximale de l'air: 120MPH

Capacité éolienne maximale: 450CFM

Type de batterie: 40V Lithium-ion, 4Ah

Modèle de batterie: DB2102

Temps de charge: 150 mins

Modèle de chargeur: DB2202A

Poids: 11 livres

FR

19

INTRODUCTION

Merci pour acheter un produit PowerSmart®. Ce manuel fournit des informations sur le fonctionnement

et l'entretien de ce produit en toute sécurité. Nous avons fait tous les efforts pour assurer l'exactitude des

informations contenues dans ce manuel. PowerSmart® se réserve le droit de modifier ce produit et ses

spécifications à tout moment et sans préavis.

Veuillez conserver ce manuel pendant toute la durée de vie de l'outil électrique à la disposition de tous les

utilisateurs.

Ce manuel contient des messages spéciaux destinés à attirer l'attention sur des problèmes de

sécurité potentiels, des dommages à l'outil électrique ainsi que des informations utiles sur le

fonctionnement et l'entretien. Veuillez lire attentivement toutes les informations pour éviter

les blessures et les dommages à la machine.

QUESTIONS ? PROBLÈMES ?

Veuillez contacter notre service clientèle pour toute question et/ou commentaire, soit par courrier

électronique : [email protected], soit par téléphone au numéro gratuit (800)791-9458. Nous

sommes disponibles du lundi au vendredi de 9 h à 17 h (heure de l'Est) pour vous aider à résoudre tout

problème que vous pourriez rencontrer.

INFORMATIONS SUR LA SÉCURITÉ

Lisez et respectez tous les avertissements, mises en garde et instructions figurant sur l'outil électrique et

dans ce manuel du propriétaire avant d'utiliser cet outil électrique.

REMARQUE : Les informations suivantes sur la sécurité ne sont pas destinées à couvrir toutes les

conditions et situations possibles qui peuvent se produire. Lisez tout le manuel du propriétaire afin de

connaître les instructions de sécurité et d'utilisation. Si vous ne respectez pas des instructions et des

consignes de sécurité, cela peut entraîner des blessures graves, voire mortelles.

Ce symbole d'alerte de sécurité est utilisé pour identifier les informations de sécurité sur les dangers qui

peuvent entraîner des blessures corporelles.

Un mot de signalisation (DANGER, AVERTISSEMENT ou ATTENTION) est utilisé avec

le symbole d'alerte pour indiquer la probabilité et la gravité potentielle d'une blessure. En

outre, un symbole de danger peut être utilisé pour représenter le type de danger.

DANGER Indique un danger qui, s'il est inévitable, entraînera la mort ou des blessures graves.

AVERTISSEMENT Indique un danger qui, s'il est inévitable, peut entraîner la mort ou des blessures

graves.

ATTENTION Indique un danger qui, s'il est inévitable, peut entraîner des blessures légères ou

modérées.

ATTENTION Indique une situation qui pourrait entraîner des dommages sans le symbole d'alerte.

20

RÈGLES GÉNÉRALES DE SÉCURITÉ

La sécurité se compose de vigilance, de bon sens et de connaissance du fonctionnement de votre outil

électrique.

CONSERVEZ CES CONSIGNES DE SÉCURITÉ.

AVERTISSEMENT: Avant d'avoir lu ce manuel d'instructions concernant la sécurité, le

fonctionnement et l'entretien, n'utilisez pas cet appareil. Si vous ne respectez pas toutes les

instructions énumérées ci-dessous, cela peut entraîner une décharge électrique, un incendie

et/ou des blessures graves.

SÉCURITÉ DES ZONES DE TRAVAIL

 Votre zone de travail doit être gardé propre et bien éclairée. Les établis encombrés et les zones

sombres sont propices aux accidents.

 Les outils électriques ne doivent pas être utilisés dans des atmosphères explosives, par exemple en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques produisent des

étincelles qui peuvent enflammer la poussière ou les fumées.

 Lorsque vous utilisez un outil électrique, tenez les spectateurs, les enfants et les visiteurs à l'écart.

Les distractions peuvent vous faire perdre le contrôle.

SATIÉTÉ ÉLECTRIQUE

 Adaptez les fiches des outils électriques à la prise. Ne modifiez jamais la fiche de quelque façon que

ce soit. Un adaptateur ne doit pas être utilisé avec des outils électriques mis à la terre. Des fiches non

modifiées et des prises adaptées réduisent le risque de décharge électrique.

 Évitez tout contact du corps avec des surfaces mises à la terre ou à la masse, comme les tuyaux, les

radiateurs, les cuisinières et les réfrigérateurs. Si votre corps est relié à la terre ou à la masse, le risque

de décharge électrique est accru.

 N'exposez pas les outils électriques à la pluie ou à l'humidité. La pénétration d'eau dans un outil

électrique augmente le risque de décharge él ectrique.

 Ne maltraitez pas le cordon. Le cordon ne doit être jamais utilisé pour transporter, tirer ou débrancher

l'outil électrique. Maintenez le cordon à l'écart de la chaleur, de l'huile, des bords tranchants ou des

pièces mobiles. Les cordons endommagés ou emmêlés augmentent le risque de décharge électrique.

 Utilisez une rallonge adaptée à une utilisation en extérieur lorsque vous utilisez un outil électrique à

l'extérieur. L'utilisation d'un cordon adapté à l'extérieur réduit le risque de décharge électrique.

 Utilisez un circuit de mise à la terre si l'utilisation d'un outil électrique dans un endroit humide est

inévitable.

SÉCURITÉ PERSONNELLE

 Lorsque vous utilisez un outil électrique, veuillez rester vigilant, regarder ce que vous faites et faire

preuve de bon sens. Si vous êtes fatigué ou sous l'influence de drogues, d'alcool ou de médicaments,

n'utilisez pas un outil électrique. Un moment d'inattention lors de l'utilisation d'un outil électrique

peut entraîner des blessures graves.

 Utilisez des équipements de sécurité. Portez toujours une protection oculaire. Dans les conditions

appropriées, un masque anti-poussière, des chaussures de sécurité antidérapantes, un casque ou une

protection auditive doivent être utilisés.

 Habillez-vous correctement. Ne portez pas de vêtements amples ou de bijoux. Contenez les cheveux

longs. Gardez vos cheveux, vos vêtements et vos gants à l'écart des pièces mobiles, car les pièces

mobiles peuvent happer les vêtements amples, les bijoux ou les cheveux longs.

La page charge ...

PowerSmart PS76402C Manuel utilisateur

PowerSmart PS76402C Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents