Axis nitris AX3331 Manuel utilisateur

Marque: Axis

Modèle: nitris AX3331

Catégorie: Rasoirs pour hommes

Taper: Manuel utilisateur

PLEASE READ DIRECTIONS COMPLETELY BEFORE USE.

nitris

Model: AX-3335

fuel

Model: AX-3331

AXIS SHAVERS INSTRUCTION MANUAL

Congratulations!

You are now the proud owner of an

Axis Rechargeable/AC-powered

Shaver AX-3335 or AX-3331.

Before using your shaver,

please read the instructions in this

manual carefully for its proper

use and care. Please keep the

manual handy for ready reference.

AXIS/Bodyline Products International, Inc.

198 N. Brandon Drive

Glendale Heights, Illinois 60139 USA

Made in China

Axis Nitris and Axis Fuel |4| english

Axis Nitris and Axis Fuel |5| english

IMPORTANT SAFETY

INSTRUCTIONS

Before you start using your shaver, please review these basic

precautions that will aid in your use of this electrical device.

Please read all instructions before using your shaver.

DANGER

To minimize the risk of electric shock…

NEVER REACH for a shaver that has been dropped into water. Unplug

the unit immediately.

DO NOT USE your shaver while bathing or showering.

ALWAYS UNPLUG your shaver after use or prior to cleaning the unit,

except when charging the unit.

DO NOT PLACE OR STORE the shaver in water or any other liquid or

where it may accidentally fall or be pulled into water.

WARNING

To avoid burns, ﬁre, electric shock or other injury…

1. Except when recharging your shaver, never leave the unit unat-

tended when plugged in.

2. Always provide close adult supervision when using your shaver near

children or the disabled.

3. Follow all instructions in this manual carefully. Do not use attach-

ments with your shaver that have not been speciﬁcally recommended

by Bodyline Products International Inc.

4. Do not use a unit that is not operating normally, has been immersed

in water or other liquid, or has a damaged cord or plug.

Axis Nitris and Axis Fuel |6| english

Axis Nitris and Axis Fuel |7| english

Call 1-877-263-9500 to arrange for service.

5. Never operate your shaver outdoors. Avoid use in the vicinity of

aerosol products or where oxygen is being administered. Also, keep

the cord away from heated surfaces.

6. When plugging in your shaver, ﬁrst attach the cord to the unit and

then plug the cord into an electric outlet. When disconnecting, be sure

to switch the unit off, unplug the cord from the electric outlet and then

detach the cord from the shaver.

7. Do not insert foreign objects into any of the openings in the unit.

8. Never store the unit with the cord attached.

9. Store your shaver and power cord in a dry place.

10. Avoid exposing the unit to direct sunlight or ambient temperatures

above 140°F (60°C).

11. To avoid injury to the face, do not use the unit if the cutters or

head assembly have been damaged.

12. Never wrap the power cord around the unit. Damage to the power

cord may result.

13. This shaver is intended and designed for use on human facial hair

only.

14. Never unplug or plug-in the shaver when your hands are moist or

wet.

15. For home use only.

WASHABLE SHAVER

A shaving appliance the hand-held part of which

may be cleaned under water

16. Use only in dry condition

17. Do not submerge shaver into water.

Axis Nitris and Axis Fuel |8| english

Axis Nitris and Axis Fuel |9| english

18. The hand-held unit shall be detached from the power supply cord

before cleaning.

19. The shaver shall not be used until it has dried.

SAVE THESE INSTRUCTIONS

PRECAUTIONS ON USING THE SHAVER

> Do not keep the shaver in a humid place, a place where the shaver

is exposed to splashes of water, or in high temperatures.

> To clean the body case of the shaver, wipe it with a cloth soaked

with a diluted water solution of a neutral detergent. Do not use thin-

ner or benzene as it will damage the plastic portions of the body.

> Do not recharge the shaver or use it with an AC power supply when

the room temperature is below 0° C or over 40° C. Also, never

recharge it under direct sunlight or near a heating element such as

heater or incandescent light.

> Do not recharge the shaver or use it with an AC power supply in a

humid place or a place where the shaver is exposed to splashes of

water.

> Do not leave the shaver unattended while it is recharged.

> If pre-shave lotion or shaver oil sticks to the body case of the

shaver, wipe it off completely. Otherwise, the plastic portions of the

shaver may be damaged.

> Before shaving, wipe off oiliness of your face. Otherwise, the shav-

ings will stick to the outer foil as the inner blade rubs against it. If

you ﬁnd the outer foil soiled, wipe it clean with tissue paper or the

like before using the shaver.

> Excessive application of shaver oil will also soil the outer foil. In that

case, wipe the foil clean with tissue paper or the like before using

the shaver. When cleaning the shaver, take care not to apply an

excess amount of shaver oil on the inner blade and outer foil.

Axis Nitris and Axis Fuel |10| english

Axis Nitris and Axis Fuel |11| english

PARTS OF YOUR SHAVER

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

AC adaptor

cleaning brush

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

trimmer

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

center slot trimmer

outer foils

outerfoilframe

outer foil frame base

inner cutters

oscillator

foil screen assembly

release buttons

on/off switch

switch lock button

side panels

foil screen assembly

LED charging indicator

and low batteryindicator

Axis Nitris and Axis Fuel |12| english

Axis Nitris and Axis Fuel |13| english

SHAVING TIPS

Keep the unit clean and dry at all times.

Wash and dry your skin thoroughly prior to shaving.

In order to achieve the closest shave and avoid unnecessary wear on

the foils, be sure that both foils contact the skin simultaneously. Do not

hold the shaver at an angle where only one foil contacts the skin – this

will cause distortion of the foil and may result in skin irritation.

Stretch your skin with your free hand while using short, circular strokes.

This will make the hairs stand out from your face and allow the cutting

heads to reach them more easily. Shave against the grain for optimum

results.

To facilitate cutting and avoid foil wear, do not apply the shaver to your

skin with high pressure.

The normal replacement period for the foil screens is about 6 months.

In order to maintain shaving performance and comfort, replace the

cutters at least once a year. To order replacement parts, please refer to

the “Ordering Replacement Parts” section of this manual.

Using this Shaver

1. Remove the protective plastic headguard. (Fig. 1)

2. Ensure that the foil screens and inner cutters are not damaged.

Replace damaged parts before using. To obtain replacement parts,

refer to the “Ordering Replacement Parts” section of this manual.

3. To turn the shaver on, depress

the lock button and slide the on/off

switch up to the “on” position. (ﬁg. 2)

fig.1

fig.2

fig.1

fig.2

1 2

Axis Nitris and Axis Fuel |14| english

Axis Nitris and Axis Fuel |15| english

.4. Gently stretch the skin of your face with your free hand while mov-

ing the shaver slowly and smoothly against the grain of your beard.

Hold the shaver at a 90° angle to your face while maintaining contact

with the foils.

5. To shave the chin area, gently pull the skin upward and stroke

the shaver in an easy up and down motion. To avoid damaging the

delicate foils, do not apply high pressure.

6. Turn shaver off and replace protective headguard.

To Shave Longer Hairs, Sideburns or Beards

The trimmer easily cuts the longer, hard to reach hairs of the face and

neck.

1. Turn the shaver on.

2. Push up the trimmer switch button into its locked position.

3. To trim sideburns, hold so that the

trimmer lightly touches the skin at a

90° angle and move downwards. To

avoid draining the battery, keep the

trimmer in its off position when not

in use.

To shave mustaches

1. Turn the shaver on.

2. Slide the on/off switch up to the “FINE” position.

3. Place the adjustable foil in gentle contact with

your skin. Move the shaver slowly while gently

stretching your skin.

Axis Nitris and Axis Fuel |16| english

Axis Nitris and Axis Fuel |17| english

Cleaning the Head and Cutter Assembly

Regular cleaning is necessary to maintain the optimal performance and

maximum comfort from the shaver. Wipe the shaver’s body using a

damp cloth and mild soap or detergent. To avoid damaging the shaver,

do not use harsh cleansers or solvents.

Wet Cleaning

1. Switch the shaver off and ensure that the power cord is not at-

tached. Depress the foil screen assembly release buttons on both

sides of the unit and gently lift the foil screen assembly off. (ﬁg. 1)

2. Switch the shaver on and allow

fresh, cold or lukewarm water to

run over the cutters. (ﬁg. 2)

3. When ﬁnished cleaning, switch

the shaver off and replace the foil

screen assembly, making sure it locks into place.

Using the Cleaning Brush

This shaver should be cleaned with the brush provided after every

three wet cleanings.

1. Switch the shaver off and ensure that the power cord is not at-

tached. Depress the foil screen assembly release buttons on both

sides of the unit and gently lift off the foil screen assembly off. (ﬁg. 1)

2. Gently brush the hairs from the inner cutters, the inside surface of

the foil screen assembly and the shaver’s case. (ﬁg. 3) To remove the

inner cutters for cleaning, gently lift

straight up from its mount. (ﬁg. 4)

3. To clean the delicate outer foil

screens, gently wipe the surface of

the foils with tissue paper, being sure

not to apply a great deal of pressure.

Fig. 1 Fig. 2

1 2

Fig. 3 Fig. 4 Fig. 5

3 4

Axis Nitris and Axis Fuel |18| english

Axis Nitris and Axis Fuel |19| english

4. When ﬁnished cleaning, reseat the inner cutters

on the mounts and replace the hairpocket, mak-

ing sure it locks into place.

Note: to ensure proper operation, the outer foil

frame assembly must be properly seated. To

avoid damaging the delicate foil screens, do not

remove them from their frame.

Worldwide Voltage

This shaver features worldwide automatic dual

voltage conversion for 100-240 volt, 50-60 Hz AC

current. You can plug the power/recharging cord into

an electric outlet virtually anywhere in the world (an

adapter plug may be necessary), and the shaver will

adjust automatically to the required voltage.

Recharging the Shaver

AX-3335 features a 5-stage LED power indicator. (ﬁg. 1)

AX-3331 features a green indicator light that ﬂashes when recharging

is needed, remains on while the shaver is charging, and turns off when

the shaver is fully charged. Use only the power/recharger cord that

came with the shaver. The shaver is also designed to be used while

plugged into an electric outlet. The unit will not charge while it is in use,

so be sure to turn the unit off to allow charging when you are ﬁnished

shaving. The shaver will provide a 3 minutes shave after 5 minutes of

charging.

5 Stage Power Indicator

Bottom LED Flashing: recharging required

LEDs Flash Sequentially and Then Lit: shaver is recharging

Fig. 3 Fig. 4 Fig. 5

Fig. 2

5 Stage Power Indicator

Bottom LED Flashing - Recharging Required

LEDs Flash Sequentially and Then Lit - Shaver is Recharging

All LEDs Lit - Shaver is Fully Recharged

LEDs Light Sequentially - Shaver is Operating Normally

Fig. 1

Axis Nitris and Axis Fuel |20| english

Axis Nitris and Axis Fuel |21| english

All LEDs Lit: shaver is fully recharged

LEDs Light Sequentially: shaver is operating

normally

When using the shaver for the ﬁrst time or if the

shaver has not been used for a long time, charge

the shaver for 16 hours.

1. Insure that the On/Off switch is in the “Off” position. First, connect

the power cord to the shaver and then plug it into an electric outlet.

2. During recharging, the LEDs will ﬂash and

then remain lit as the unit recharges. Recharging generally takes one

hour. When fully charged, the shaver will provide approximately one

week of shaving run time.

Storing the Shaver and Power cord

If the shaver is to remain unused for a long period of time, store the

unit and power cord in a cool, dry place. Do not wrap the cord around

the unit during storage. Avoid twisting the power cord. Be sure to

unplug and untwist the cord if it becomes twisted during use or while

charging.

Removing the Batteries for Disposal/ Recycling

It is important that the rechargeable batteries in the shaver be recycled

or properly disposed of after it has reached the end of its useful life.

Turn the On/Off Switch “on” and run the shaver until the inner cutters

stop.

1. Remove the headguard, foil screen assembly, and inner cutters.

2. Remove the 2 screws on the top of shaver. (Fig.

3. Remove the 5 screw covers on the back of

shaver. Remove 2 side panels.

Fig. 2

5 Stage Power Indicator

Bottom LED Flashing - Recharging Required

LEDs Flash Sequentially and Then Lit - Shaver is Recharging

All LEDs Lit - Shaver is Fully Recharged

LEDs Light Sequentially - Shaver is Operating Normally

Fig. 1

Axis Nitris and Axis Fuel |22| english

Axis Nitris and Axis Fuel |23| english

4. Remove 5 screws on the back

of shaver.

5. Gently pull the two halves of the

shaver body apart.

6. Pull the batteries out from the

shaver.

7. Cut the wires that connect the

batteries (4 wires for batteries) with

nippers.

WARNING! To avoid the risk of bursting and the subsequent release of

toxic materials, never mutilate or place the batteries in ﬁre. To prevent

accidental burns, avoid short-circuiting the batteries. Dispose of batter-

ies in accordance with local disposal/recycling requirements.

To Replace Foil Screens

IMPORTANT: For the best shaving performance and results, we recom-

mend that you replace the shaver’s foil screens every six months and

inner cutters at least once a year.

Skin irritation or a deterioration of shave qual-

ity typically indicates that your foils need to be

replaced. Replacement intervals will vary with

individual use and hair types.

(Please refer to the “Ordering Replacement Parts”

section)

1. Remove the foil screen assembly by pressing

the release buttons on both sides of the shaver

and lifting off the assembly off. (ﬁg. 1)

2. The Outer Foils are mounted to the Outer

Foil Frame. Release the Foil Frame from the Foil

Frame Base by gently sliding a ﬁngernail between

Fig. 1

Fig. 3

Fig. 2

Fig. 1

Fig. 3

Fig. 2

Fig. 1

Fig. 3

Fig. 2

Fig. 1

Axis Nitris and Axis Fuel |24| english

Axis Nitris and Axis Fuel |25| english

the side of the Foil Frame and the Foil Frame base. (ﬁg. 2) Inverting the

Foil Base will allow the Foil Frame to drop out. (ﬁg. 3)

3. Position the replacement Outer Foils over the cutters. Be careful not

to damage the foils. Gently slide the head assembly down until it seats

ﬁrmly into place.

To Replace the Inner Cutters

(Please refer to the “Ordering Replacement Parts”

section)

NOTE: Always replace foil screens when replacing

the inner cutters.

1. Remove the foil screen assembly by pressing

the release buttons on both sides of the shaver

and lifting it off. (ﬁg. 1)

2. Remove the inner cutters by grasping and

lifting upwards. (ﬁg. 2)

3. Be sure to hold the replacement cutters ﬁrmly as you carefully insert

them into the inner cutter mounts.

4. Push the replacement cutters down ﬁrmly until they lock into place.

5. Replace the foil screen assembly and gently slide it down until you

hear it lock into place.

Ordering replacement parts

Please contact Axis/BPI at 1-877-263-9500 to order replacement

parts for your Axis shaver. Please refer to the following part number.

Part number: AN-2

Description: Replacement Outer Foil Frame and Inner Cutters for

Model AX-3335/AX-3331

Fig. 3

Fig. 2

Fig. 1

Fig. 3

Fig. 2

Fig. 1

Axis Nitris and Axis Fuel |26| english

Axis Nitris and Axis Fuel |27| english

> The above part is available at the retailer from whom your shaver

was purchased.

If your shaver requires service:

Call Axis at 1-877-263-9500. To assist us in serving you, please have

the model number and date of purchase for your shaver available.

1-YEAR LIMITED WARRANTY

AXIS/Bodyline Products International, Inc. (BPI) warrants that your

product, except as noted below, is on the date of purchase free from

defect in material and workmanship for a period of one year. In the

event of a defect in material or workmanship, AXIS / BPI will repair or

replace this product with new parts, free of charge as follows:

1. The warranty is extended only to the original purchaser. A purchase

receipt or other proof of date of the original purchase is required for

service and parts replacement under this warranty.

2. Do not return the product to the retailer from whom this product

was purchased.

3. Contact AXIS/BPI toll-free at 1-877-263-9500 to obtain authoriza-

tion during the warranty period to return the defective product by mail,

postage prepaid.

LIMITATIONS AND EXCLUSIONS

There are no express warranties except as listed above.

This warranty only covers failures due to defects in materials or work-

manship that occur during normal use. It does not cover foils, blades,

cutters, or attachments or damage that occurs in shipment, or failures

that are caused by products not supplied by AXIS / Bodyline Products

International, Inc., or failures that result from accident, misuse, abuse,

and neglect from mishandling, misapplication, improper maintenance,

improper cleaning, alteration, modiﬁcation, line power surge, or com-

Axis Nitris and Axis Fuel |28| english

mercial use of the product, such as hotel, ofﬁce or rental use of the

product, or service by anyone other than AXIS / Bodyline Products

International, Inc., or damage that is attributable to acts of God.

AXIS / BODYLINE PRODUCTS INTERNATIONAL, INC. SHALL NOT BE

LIABLE FOR INCIDENTAL OR CONSEQUENTAL DAMAGES RESULT-

ING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY

BREACH OF THIS WARRANTY.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WAR-

RANTIES OF MERCHANDISE AND FITNESSS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD

SET FORTH ABOVE.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, or limitations on how long an implied warranty

lasts, so the above exclusions and limitations may not apply to you.

This warranty gives you speciﬁc legal rights and you may also have

Félicitations!

Vous êtes maintenant l’heureux

propriétaire d’un rasoir Axis

AX-3335 ou AX-3331 recharge-

able ou fonctionnant sur secteur

courant alternatif (CA).

Avant d’utiliser votre rasoir, veuillez

lire attentivement les instructions de

ce manuel d’emploi pour une bonne

utilisation et un bon entretien du ra-

soir. Veuillez garder le manuel à por-

tée de main pour toute référence.

Axis Nitris and Axis Fuel |30| Francais

Axis Nitris and Axis Fuel |31| Francais

INSTRUCTIONS

IMPORTANTES

CONCERNANT VOTRE

SÉCURITÉ.

Il est nécessaire de toujours observer certaines précautions élémen-

taries en utilisant un appareil électrique.

Veuillez lire attentivement toutes ces instructions

avant d’utiliser votre nouveau rasior.

DANGER

Pour limiter les risques d’électrocution...

1. NE JAMAIS RÉCUPÉRER un rasoir une fois tombé à l’eau. Deb-

rancher l’appareil immédiatement.

2. NE PAS UTILISER le rasoir dans le bain ou sous la douche.

3. DÉBRANCHER TOUJOURS le rasoir après l’emploi ou avant de le

nettoyer, sauf s’il est en cours de chargement.

4. NE PAS METTRE OU RANGER le rasoir dans de l’eau ou tout autre

liquide, ou encore dans un lieu d’où il peut accidentellement tomber ou

être amené dans l’eau. Appelez 1-877-263-9500 pour tout service

apres-vente.

AVERTISSEMENT

Pour eviter toute brulure, danger d’incedie, electrocution ou autre...

1. Ne jamais laisser le rasoir branche sans surveillance sauf lors de

son chargement.

Axis Nitris and Axis Fuel |32| Francais

Axis Nitris and Axis Fuel |33| Francais

2. Assurer toujours un etroite surveillance si le rasoir est utilise en

presence d’enfants ou de personnes handicapees.

3. Suivez attentivement toutes les instructions de ce manuel. Ne pas

utliser d’accessoires qui ne sont pas spéciﬁquement recommandés

par avec le rasoir.

4. Ne pas utiliser l’appareil s’il ne fonctionne pas normalement, a

été immergé dans de l’eau ou toute autre liquide, ou si le cordon

d’alimentation ou la prise sont endommagés. Appelez 1-877-263-

9500 pour tout service apres-vente.

5. Ne jamais utlitiser le rasoir en plein air. Éviter d’utiliser à proximité

d’aérosols ou en cas d’adminitration d’oxygène. Toujours garder le

cordon d’alimentation éloigné des surfaces chaffées.

6. Por brancher le rasoir raccorder déjà le cordon d’alimentation à

l’appareil avante de la brancher dans une prise électrique. Avante de

débrancher l’appareil, vériﬁer qu’il est sur arrêt, débrancher le cordon

d’alimentation de la prise électrique, puis retirer le cordon du rasoir.

7. Ne pas insérer de corps étrangers dans les oriﬁces de l’appareil.

8. Ne jamais ranger le rasoir sans avoir désolidarisé le cordon.

9. Ranger le rasoir et le cordon d’alimentation dans un lieu sec.

10. Éviter d’exposer l’appareil à la lumière directe du soileil ou à une

températrure ambiante supérieure à 60 degrés C.

11. Pour éviter toute blessure au visage, ne pas utiliser l’appareil si les

lames ou les têtes ont été endommagées.

12. Ne jamais enrouler le cordon d’alimentation autour de l’appareil

sous peine de l’endommager.

13. Ce rasoir est conçu et destiné à être utilisé sur les poils du visage

uniquement.

14. Ne jamais débrancher ou brancher le rasoir ayant les mains

Axis Nitris and Axis Fuel |34| Francais

Axis Nitris and Axis Fuel |35| Francais

humides ou mouillées.

15. Produit à usage ménager uniquement.

RASOIR LAVABLE

un dispositif de rasage qui fonctionne avec l’électricité dont rasant des

lames peut être nettoyé sous l’eau.

16. Employez seulement dans la condition sèche

17. Ne submergez pas le rasoir dans l’eau

18. Le rasoir doit être détaché de la corde électrique avant le nettoy-

age

19. N’utilisez pas le rasoir jusqu’à ce qu’il ait séché

CONSERVEZ CES

INSTRUCTIONS

PRÉCAUTIONS D’EMPLOI DU RASOIR

> Ne rangez pas le rasoir dans un lieu humide ou un lieu où il est

exposé à des éclaboussures ou à des températures élevées.

> Pour nettoyer le boîtier principal du rasoir, utilisez un chiffon humide

avec un détergent neutre dilué à l’eau. N’utilisez pas de diluant ou

de benzène car cela endommagerait les parties en plastique du

boîtier.

> Ne rechargez ou n’utilisez pas le rasoir avec un adaptateur CA

lorsque la température est inférieure à 0° C ou supérieure à 40° C.

De plus, ne le rechargez jamais en plein soleil ou près d’une source

de chaleur tel qu’un radiateur ou une lampe à incandescence.

> Ne chargez ou n’utilisez pas le rasoir avec une alimentation CA dans

un lieu humide ou un lieu où le rasoir est exposé à des éclabous-

sures.

Axis Nitris and Axis Fuel |36| Francais

Axis Nitris and Axis Fuel |37| Francais

> Ne laissez pas le rasoir sans surveillance lorsque il est rechargé.

> Si de la lotion avant rasage ou de l’huile de nettoyage du rasoir

reste collée sur le boîtier du rasoir, éliminez-la totalement. Sinon, les

parties en plastique du rasoir pourraient être endommagées.

> Avant le rasage, nettoyez bien les parties grasses de la peau. Sinon,

les poils resteront collés à la grille externe lorsque la lame intérieure

la frotte. Si la grille externe est sale, nettoyez la avec un mouchoir en

papier ou quelque chose du même type avant d’utiliser le rasoir.

> Une utilisation excessive d’huile de nettoyage salira également la

grille externe. Dans ce cas, essuyez la grille externe avec un mouch-

oir en papier ou quelque chose du même type avant d’utiliser le

rasoir. Lors du nettoyage du rasoir, n’appliquez pas une quantité trop

importante d’huile sur la lame interne et sur la grille externe.

PARTS OF YOUR SHAVER

Capuchon de protection

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

Adaptateur CA

Brosse de nettoyage

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

Tondeuse

headguard

cleaning brush

outer foils

outer

foil

frame

center slot

trimmer

foil screen assembly

inner cutters

oscillator

foil screen

assembly

release buttons

on/off switch

side panels

LED charging

indicator and

low battery

indicator

AC power/recharging

cord with safety plug

switch lock

button

outer foil

frame base

Axis Nitris and Axis Fuel |38| Francais

Axis Nitris and Axis Fuel |39| Francais

tondeuse à emplacement central

grilles externes

cadre desgrilles externes

socle du cadre

des grilles externes

couteaux internes

oscillateur

ensemble écran-grilles

boutons d’éjection release buttons

interrupteur marche / arrêt (on/off)

bouton de verrouillage de l’interrupteur

panneaux latéraux

ensemble écran-grilles

témoins lumineux del de charge

etde batterie/pile épuisée

CONSEILS POUR LE RASAGE

Maintenez l’appareil propre et sec à tout moment.

Lavez-vous et séchez-vous la peau soigneusement avant de vous

raser.

Aﬁn de réaliser un rasage des plus précis et d’éviter une usure inutile

des grilles, veillez à ce que les deux grilles entrent en contact avec

la peau en même temps. Ne tenez pas le rasoir selon un angle où

seule l’une des grilles est en contact avec la peau (cela causerait une

déformation de la grille et pourrait aboutir à une irritation de la peau).

Étirez la peau avec la main libre tout en faisant de courts mouvements

circulaires. Cela permettra de redresser les poils et ainsi les têtes de

coupe pourront les atteindre plus facilement. Passez le rasoir dans le

sens contraire de celui de la pousse du poil pour obtenir les meilleurs

résultats.

La page charge ...

Axis nitris AX3331 Manuel utilisateur

Marque: Axis

Modèle: nitris AX3331

Catégorie: Rasoirs pour hommes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Axis nitris AX3331 User manual
español: Axis nitris AX3331 Manual de usuario

Axis nitris AX3331 Manuel utilisateur

Axis nitris AX3331 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents