NEXEL 243037 Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur
1
USER MANUAL
Read this manual thoroughly prior to equipment set-up, operation or maintenance.
Model 243037
NEXEL® Merchandiser Refrigerator
3 Door, 78-1/4"W x 30D x 80-3/4H
For questions, please contact NEXEL® Customer Service at 1-800-245-6682 or visit www.nexelwire.com
2
WARNING
DANGER RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED. TO BE REPAIRED ONLY BY TRAINED
SERVICE PERSONNEL. DO NOT PUNCTURE REFRIGERANT TUBING.
PELIGRO - RIESGO DE INCENDIO O EXPLOSIÓN. CONTIENE REFRIGERANTE INFLAMABLE. DEBE SER REPARADO
SOLAMENTE POR UN PERSONAL DE SERVICIO CALIFICADO.
DANGER RISQUE DE FEU OU D’EXPLOSION. LE FRIGORIGÈNE EST INFLAMMABLE. CONFIER LES
RÉPARATIONS À UN TECHNICIEN SPÉCIALISÉ. NE PAS PERFORER LA TUBULURE CONTENANT LE FRIGORIGENE.
CAUTION RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED. CONSULT REPAIR
MANUAL/OWNER’S GUIDE BEFORE ATTEMPTING TO SERVICE THIS PRODUCT. ALL SAFETY PRECAUTIONS MUST BE
FOLLOWED.
ATENCION - RIESGO DE INCENDIO O EXPLOSIÓN. CONTIENE REFRIGERANTE INFLAMABLE. CONSULTE EL MANUAL DE
REPARACIÓN / GUÍA DEL PROPIETARIO ANTES DE INTENTAR DAR SERVICIO A ESTE PRODUCTO. DEBEN CUMPLIR CON
TODAS LAS PRECAUCIONES DE SEGURIDAD.
ATTENTION RISQUE DE FEU OU D’EXPLOSION. LE FRIGORIGÈNE EST INFLAMMABLE. CONSULTER LE MANUEL DU
PROPRIÉTAIRE/GUIDE DE RÉPARATION AVANT DE TENTER UNE RÉPARATION. TOUTES LE MESURES DE SÉCURITÉ
DOIVENT ÊTRE RESPECTÉES.
CAUTION RISK OF FIRE OR EXPLOSION DUE TO PUNCTURE OF REFRIGERANT TUBING; FOLLOW HANDLING
INSTRUCTIONS CAREFULLY. FLAMMABLE REFRIGERANT USED.
ATENCION - RIESGO DE INCENDIO O EXPLOSIÓN DEBIDO A LA PERFORACIÓN DE LA TUBERÍA REFRIGERANTE; SIGA
LAS INSTRUCCIONES DE MANIPULACIÓN CON CUIDADO. CONTIENE REFRIGERANTE INFLAMABLE.
ATTENTION RISQUE DE FEU OU D’EXPLOSION SI LA TUBULURE CONTENTANT LE FRIGORIGÈNE EST PERFORÉE;
SUIVRE LES INSTRUCTIONS DE MANUTENTION AVEC SOIN. LE FRIGORIGÈNE EST INFLAMMABLE.
CAUTION RISK OF FIRE OR EXPLOSION DUE TO FLAMMABLE REFRIGERANT USED. FOLLOW HANDLING
INSTRUCTIONS CAREFULLY IN COMPLIANCE WITH LOCAL GOVERNMENT REGULATIONS.
ATENCIÓN RIESGO DE INCENDIO O EXPLOSIÓN DEBIDO A REFRIGERANTE INFLAMABLE UTILIZADO. SIGA LAS
INSTRUCCIONES DE MANEJO DE ACUERDO CON LAS REGULACIONES DEL GOBIERNO LOCAL.
ATTENTION RISQUE DE FEU OU D'EXPLOSION EN RAISON DU REFRIGERANT INFLAMMABLE UTILISE. SUIVRE LES
INSTRUCTIONS DE MANUTENTION AVEC SOIN CONFORMÉMENT AUX RÈGLEMENTATION GOUVERNEMENTALE
LOCAUX.
3
SPECIFICATIONS
Dimensions
78-1/4"W x 30"D x 80-3/4"H
Number of Doors
3
Number of Shelves
12
Casters
Yes
Capacity (Cubic Ft.)
53
HP
3/4
Voltage
115
Amps
8.4
Plug Type
NEMA 5-15P
Temperature Range
33°F to 41°F
Exterior Construction
Powder Coated Steel
Interior Construction
Painted Aluminum
Shelf Construction
Epoxy-Coated Steel
Door Construction
Double Pane Glass
Refrigerant
R290
Unit Weight
615 lbs.
Hertz
60 Hz
Phase
1
Cord Length
7 ft.
Interior Lighting
LED
Warranty
1 Year
4
INSTALLATION
Read this entire manual thoroughly prior to equipment set-up, operation and/or maintenance.
IMPORTANT:
If the refrigerator has recently been transported on its side, allow the unit to stand upright for a minimum
of 24 hours before plugging it in.
Make sure all shelves and accessories are properly installed before plugging in the unit.
Do not attempt to remove or repair any component of the unit. Consult an authorized service technician
for all servicing and repair needs.
Do not hang on doors or stand inside the unit.
Make sure the refrigerator has reached the desired temperature before loading.
Location Guide
Install unit on a strong and leveled surface. If the surface is uneven, the refrigerator may be noisy or
malfunction.
Install unit in an indoor, well ventilated area. Outdoor use may cause decreased efficiency and damage to
the unit. Avoid direct sunlight.
For best performance, allow 6” of clearance on sides and the back of the unit during operation.
Avoid installation in high humidity and/or dusty areas. High humidity can cause the unit to rust and may
decrease efficiency. Dust collected on the condenser coil may cause unit to malfunction.
5
Select a location away from heat and moisture-generating equipment. High ambient temperatures may
cause the compressor to malfunction.
Electrical Warnings
Ensure that the required voltage is being supplied at all times.
The refrigerator should be plugged into a grounded and properly-sized electrical outlet with appropriate
overcurrent protection. Each unit should have its own dedicated outlet. Please refer to the electrical
requirements on the unit’s nameplate.
Do not use extension cords.
Ensure the refrigerator is not resting on or against the electrical cord.
If the unit is not in use for a long period of time, unplug it from the outlet.
To avoid shock and fire hazards, do not plug in or unplug the unit with wet hands.
After unplugging the unit, wait 10 minutes prior to plugging it back in. Failure to do so could cause damage
to the compressor.
TEMPERATURE CONTROLS
KEY COMBINATIONS
To Lock or Unlock the Keyboard
To Enter Programming Mode
To Return to Room Temperature Display
To display the set temperature. In programming mode it
selects a parameter or confirms an operation.
To start a manual defrost.
In programming mode it browses the parameter codes or
increases the displayed value.
In programming mode it browses the parameter codes or
decreases the displayed value.
6
LED
MODE
INDICATES
On
Compressor Enabled
Flashing
Anti-Short Cycle Delay Enabled (AC Parameter)
On
Defrost in Progress
Flashing
Dripping in Progress
On
Fans Output Enabled
Flashing
Fans Delay After Defrost
On
Measurement Unit
Flashing
Programming Mode
NOTE: Your new refrigerator is already factory-set to run at optimum temperatures for food safety and should
require no adjustments. Your refrigerator is set to cycle between a minimum temperature of 33°F and a
maximum temperature of 40°F. Adjusting the temperature changes the minimum temperature your unit will
run at. Your refrigerator will not run constantly at this temperature setting.
HOW TO VIEW THE SET TEMPERATURE
1. Push and immediately release the SET key, the set temperature will be displayed.
2. To return to standard view, wait about 5 seconds or push and immediately release the SET key again.
HOW TO CHANGE THE SET TEMPERATURE
1. Push and hold the SET key for 2 seconds.
2. The °F LED will start to blink and the current temperature will be displayed.
3. To change the set temperature push the or arrows.
4. Push the SET key to store the new temperature or wait 10 seconds and new temperature will
automatically be set.
HOW TO START A MANUAL DEFROST
NOTE: Units are pre-programmed to run automatic defrost cycles at preset intervals. If you would like to run a
manual defrost cycle at any time, follow these instructions:
1. Push and hold the key for 2 seconds.
2. Repeat to stop the defrost cycle.
Refrigerator coils are kept below the freezing point (32°F). During compressor down-time, the evaporator fan
continues to circulate air through the evaporator coil. This air circulation raises the coil temperature above the
freezing point, melting any accumulated frost. Run-off water is drained into the evaporator pan and
evaporated.
7
OPERATION/MAINTENANCE
NOTE: It is strongly recommend that any servicing be performed by an authorized service technician.
During maintenance and cleaning, please unplug the unit.
LOADING PRODUCTS
Do not block the inside air duct/fan at the top of your refrigerator. Maintain a minimum clearance of 4”
between products and the fan at all times.
Ensure all shelves are level and properly secured prior to loading products.
Do not store flammable and/or explosive gas or liquids inside the unit.
CLEANING THE CONDENSER COIL
For efficient operation, keep the condenser surface free of dust, dirt and lint.
We recommend cleaning the condenser coil at least once per month.
Clean the condenser with a commercial condenser coil cleaner, available from any kitchen equipment
retailer.
CLEANING THE FAN BLADES AND MOTOR
If necessary, clean the fan blades and motor with a soft cloth.
If it is necessary to wash the fan blades, cover the fan motor to prevent moisture damage.
CLEANING THE INTERIOR OF THE UNIT
When cleaning the cabinet interior, use a solvent of warm water and mild soap.
Do not use steel wool, caustic soap, abrasive cleaners or bleach that may damage the interior finish of
the cabinet.
Wash door gaskets on a regular basis, preferably weekly. Simply remove the door gasket from the frame
of the door, soak it in warm water and soap for 30 minutes. Dry with soft cloth and replace.
Check door gaskets for proper seal after they are replaced.
Periodically remove the shelves and shelf brackets from the unit, and clean them with a mild soap and
warm water.
8
TROUBLESHOOTING
PROBLEMS
SOLUTIONS
Compressor is Not Running
Fuse blown or circuit breaker tripped.
Replace fuse or reset circuit breaker.
Power cord unplugged.
Plug in power cord.
Thermostat set too high.
Set thermostat to lower temperature.
Cabinet in defrost cycle.
Wait for defrost cycle to finish.
Cabinet Temperature is too Warm
Thermostat is set too high.
Set thermostat to lower temperature.
Airflow is blocked.
Re-arrange products to allow for proper air flow. Make sure
there is at least four inches of clearance from the fan.
Low refrigerant levels.
Contact a service technician to check refrigerant levels.
Door is slightly ajar.
Make sure door is completely closed.
Interior Light is Not Working
Poor switch connection.
Turn off light switch and turn it back on.
Bulb is not connected.
Make sure the bulb is correctly inserted in the socket.
Bulb has burned out.
Replace the bulb.
Condensation is Collecting on the
Cabinet and/or Floor
Gasket is not sealing properly.
Clean, repair, or replace the gasket as necessary.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

NEXEL 243037 Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur

dans d''autres langues