R.H. Peterson American Fyre Designs Unvented Series Installation & Owner's Manual

1

REV 3 - 1910241100

L-H2-011

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLATION &

OWNER’S MANUAL

WARNING: If the information in this manual

is not followed exactly, a ﬁre or explosion may

result causing property damage, personal

injury or loss of life.

- Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity

of this or any other appliance.

- A propane cylinder not connected for use

shall not be stored in the vicinity of this or

any other appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ﬂame.

3. If odor continues, keep away from the

appliance and immediately call your gas

supplier or ﬁre department.

Installation and service must be performed by

an NFI Certiﬁed or other qualiﬁed professional

installer, service agency, or gas supplier.

WARNING

Improper installation, adjustment, alteration,

service, or maintenance can cause property

damage, personal injury, or loss of life. Read

the installation, operating and maintenance

instructions thoroughly before installing or

servicing this equipment.

CODE AND SUPPLY REQUIREMENTS:

The gas installation must conform with local codes

and ordinances, or, in the absence of local codes,

with the latest National Fuel Gas Code, ANSI Z223.1.

The R.H.P. gas appliance is designed as an

attended appliance. Adults must be present when

the unit is operating. DO NOT leave the unit burning

when unattended. If the product is left burning

unattended, it may cause damage or serious injury.

INSTALLER & CONSUMER: These instructions MUST

be retained with this unit for future reference.

Important: Read these instructions carefully

before starting installation of the unit.

IMPORTANT

For safe operation and proper performance of this

product and to comply with certiﬁcation, listings,

and building code acceptances, use ONLY Robert

H. Peterson (R.H.P.) controls, parts, decorative

media, and accessories that have been speciﬁcally

listed or certiﬁed for use with this ﬁreplace. Use of

other controls, parts, or accessories is prohibited

and will void all warranties, certiﬁcations, listings,

and building code approvals, and may cause

property damage, personal injury, and loss of life.

Complies with:

ANSI Z21.97/CSA 2.41 for

outdoor decorative gas

appliances

(when installed with select

R.H.P. Vented/Unvented

Gas Appliances)

WARNING: For Outdoor Use Only

DANGER

CARBON MONOXIDE HAZARD

A vented gas appliance can produce

carbon monoxide which has no odor.

Using it in an enclosed space can

kill you.

Never use the appliance in an

enclosed space such as a camper,

tent, car, or home.

PHOENIX & MARIPOSA OUTDOOR FIREPLACES

Vented Series: 017, 073, 818, 868

Unvented Series: 117, 173, 118, 168

017

series

shown

2

REV 3 - 1910241100

L-H2-011

AVERTISSEMENT

L'installation, l'ajustement, le changement, le

service, ou l'entretien inexact peuvent causer des

dégats matériels, le dommage corporel, ou des

pertes humaines. Lisez l'installation, l'opération

et les instructions d'entretien complètement avant

d'installer ou entretenir cet équipement.

CONDITIONS DE CODE ET D'APPROVISIONNEMENT:

L'installation de gaz doit se conformer aux codes

locaux et aux ordonnances, ou, en l'absence des

codes locaux, au plus défunt code national de gaz de

carburant, la norme ANSI Z223.1.

Le R.H.P. Appareil à gaz est conçu comme un appareil

assisté. Les adultes doivent être présents lorsque

l'appareil est en marche. Ne laissez pas l'appareil est

en marche sans surveillance. Si le produit est laissé

brûler sans surveillance, il peut causer des dommages

ou des blessures graves.

AVERTISSEMENT: Si l'information en

ce manuel n'est pas suivie exactement, une

incendie ou une explosion peut résulter

entraînant des dégats matériels, le dommage

corporel ou des pertes humaines.

- Ne pas entreposer ni utiliser d'essence ou

d'autres vapeurs et liquides inﬂammables

à proximité de cet appareil ou de tout autre.

- Une bouteille de propane non branchée ne

doit pas être entreposée à proximité de cet

ou tout autre appareil.

DANGER

Si vous sentez une odeur de gaz:

1. Coupez le gaz à l'appareil.

2. Éteindre toute ﬂamme nue.

3. Si l'odeur persiste, éloignez-vous de

l'appareil et appelez immédiatement votre

fournisseur de gaz ou les pompiers.

L'installation et le service doivent être

assurés par un NFI certiﬁé ou toute autre

installateur, agence de service, ou fournisseur

professionnelle qualiﬁée de gaz.

d'INSTALLATEUR; CONSOMMATEUR: Ces

instructions DOIVENT être maintenues avec cet appareil

pour la future référence.

Important: Lisez ces instructions soigneusement avant

de commencer l'installation de l'unité.

IMPORTANT

Pour un fonctionnement en toute sécurité et le bon

fonctionnement de ce produit et pour être conforme à

la certiﬁcation, aux listes et aux normes du bâtiment,

utilisez UNIQUEMENT les commandes, pièces,

supports décoratifs et accessoires Robert H. Peterson

(R.H.P.) spécialement homologués ou certiﬁés pour

être utilisés avec cette cheminée. L'utilisation d'autres

commandes, pièces ou accessoires est interdite et

annulera toutes les garanties, certiﬁcations, listages et

approbations du code du bâtiment, et pourrait causer

des dommages matériels, des blessures et la mort.

AVERTISSEMENT: Pour l'usage extérieur

seulement

INSTALLATION ET

MODE D'EMPLOI

Conforme à:

ANSI Z21.97/CSA 2.41 pour

l'extérieur des appareils à gaz

décoratifs

(lorsqu'il est installé avec

sélection R.H.P. Ventilé / non

ventilé les appareils à gaz)

DANGER

CARBON MONOXIDE HAZARD

Un foyer à gaz ventilé peut produire

du monoxyde de carbone qui n'a pas

d'odeur.

Son utilisation dans un espace clos

peut vous tuer.

Ne jamais utiliser l'appareil dans un

espace clos, tel qu'une caravane,

tente, voiture ou à la maison.

Série

017

montré

PHOENIX & MARIPOSA CHEMINÉES D'EXTÉRIEUR

Ventilé Série: 017, 073, 818, 868

Non Ventilé Série: 117, 173, 118, 168

3

REV 3 - 1910241100

L-H2-011

TABLE OF CONTENTS

GETTING STARTED

PRE-INSTALLATION AND PREPARATION SAFETY GUIDELINES ��4

INSTALLATION SAFETY GUIDELINES ��5

OPERATING THE UNIT SAFELY AND CORRECTLY ��5

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS ��7

SPECIFICATIONS AND DIMENSIONS ��8

MINIMUM CLEARANCES ��11

TOOLS REQUIRED ��11

PARTS LIST �� 12

INSTALLATION

IMPORTANT SAFETY INFORMATION �� 15

FIREPLACE INSTALLATION �� 15

BEFORE YOU BEGIN �� 15

LOCATION �� 15

FIREPLACE ASSEMBLY - OVERVIEW �� 16

GAS SUPPLY SETUP (if applicable) �� 17

FIREPLACE ASSEMBLY - STEP BY STEP �� 17

BURNER INSTALLATION �� 22

BURNER INSTALLATION GUIDELINES �� 22

LEAK TEST �� 22

OPTIONAL ACCESSORIES �� 23

OPTIONAL GFRC CHIMNEY RAIN VENT CAP �� 23

OPTIONAL SCROLL SCREEN �� 23

OPTIONAL GFRC PROTECTOR PLATE �� 23

USE, CARE, & SERVICE

LIGHTING GUIDELINES �� 25

FOR YOUR SAFETY, READ BEFORE LIGHTING �� 25

TO LIGHT THE APPLIANCE �� 25

TO SHUT OFF GAS TO THE APPLIANCE �� 25

SERVICING AND CLEANING �� 26

ANNUAL CLEAN / INSPECTION GUIDELINES �� 26

CONCRETE CARE �� 27

TROUBLESHOOTING �� 27

WARRANTY �� 28

IMPORTANT SAFETY INFORMATION

Congratulations on your purchase of an American Fyre Designs outdoor gas ﬁreplace. Made with pride in America,

your new ﬁreplace complies with national safety standards and when installed per these instructions and used

as intended it will provide warmth and comfort to your outdoor area for many years.

Prior to installation and operation ensure that all speciﬁcations, dimensions, and minimum clearances

stated in this manual are observed. You must read all warnings and safety information, and understand

all of the information in this manual. All installation requirements must be observed and met.

4

PRE-INSTALLATION AND PREPARATION SAFETY GUIDELINES

This ﬁreplace is designed to be installed with select R.H.P. vented/unvented gas appliances. The following

3 sections of warnings apply to this complete setup type:

A. A shut-off valve (not included) in the gas line is optional. It provides for safety when the unit is not in use

and for convenient maintenance and repair. It can be installed within 6 feet of unit. Use a pipe joint compound

resistant to all gasses on all male ﬁttings except ﬂare ﬁttings.

B. Before installing this unit, check the MINIMUM CLEARANCES section to ensure that the surrounding area is

properly sized for the installation.

C. The unit is for outdoor use only. DO NOT install or use this appliance inside a building, garage, or any other

enclosed area, including recreational vehicles and/or boats. THIS UNIT MUST BE INSTALLED SO THAT

THE VENT OPENINGS AND SURROUNDING AREA OF THE UNIT REMAIN CLEAR AND FREE AT ALL

TIMES.

D. SOLID FUEL MUST NOT BE BURNED in the unit.

E. CHECK GAS TYPE (natural gas or propane): The gas supply you intend to use may not be the same as that

stated on the burner rating plate as purchased. If the gas supply is different, DO NOT INSTALL, and contact

the dealer for assistance.

F. FOR NATURAL GAS: The minimum inlet gas-supply pressure for purposes of input adjustment is 5" water

column (w.c.), and the maximum inlet gas-supply pressure is 10.5 " w.c.

FOR PROPANE GAS: The minimum inlet gas-supply pressure for purposes of input adjustment is 11" w.c., and

the maximum inlet gas-supply pressure is 13" w.c. DO NOT INSTALL THIS UNIT IF MINIMUM PRESSURE

IS NOT AVAILABLE OR IF MAXIMUM PRESSURE IS EXCEEDED.

G. The gas piping system must be sized to provide minimum inlet pressure at the maximum ﬂow rate

(BTU/hr). Undue pressure loss will occur if the pipe is too small, or the run is too long. Gas supply pipe must

be

1

/

2

" minimum interior diameter. If the gas line is longer than 20', a larger diameter line may be necessary.

Refer to the NFPA 54 guidelines for further details.

H. For installations at elevations above 2,000 ft., contact your local dealer or gas supplier before installing. Input

ratings should be reduced approximately 4% per 1,000 ft. above sea level. Refer to National Fuel Gas Code.

I. The gas appliance and the individual shut-off valve must be disconnected from the gas-supply piping system

during any pressure testing of that system at test pressures in excess of

1

/

2

psi (3.5 kPa). This is accomplished

by closing the gas-supply line valve. The unit must be isolated from the gas-supply piping system by closing its

individual manual shut-off valve during any pressure testing of the gas-supply piping system at test pressures

equal to or less than

1

/

2

psi (3.5 kPa).

J. When a gas appliance is for connection to a ﬁxed piping system, the installation must conform with local codes,

or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel

Gas Code, Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code,

B149.2, as applicable.

K. INSTALLER NOTE: This unit should be installed so that it can be removed if service is required.

L. GAS-SUPPLY PLUMBING REQUIREMENTS

Apply only joint compounds that are resistant to all gasses on all male pipe ﬁttings. Make sure to tighten every

joint securely. Do not use pipe joint compound to connect ﬂare ﬁttings. Bring the gas-supply pipe up from

beneath the hearth or directly behind the hearth as appropriate for your installation.

CAUTION: Installation and maintenance must be done by an NFI Certiﬁed or other qualiﬁed professional service

technician. Installer, read these instructions (and all other instructions provided with separately purchased

product) before installing. Be sure you understand all safety precautions and warnings contained in the

manual(s).

GETTING STARTED

5

OPERATING THE UNIT SAFELY AND CORRECTLY

INSTALLATION SAFETY GUIDELINES

A. Carefully inspect for shipping damage. If any parts are damaged, call the dealer.

B. Installation and repair should be done by a qualiﬁed professional service technician. The gas appliance should

be inspected before use and at least annually by a qualiﬁed service person. More frequent cleaning may be

required as necessary. It is imperative that control compartment, burners and circulating air passageways of

the ﬁreplace and/or appliance are kept clean.

C. Correct installation and proper placement of the gas appliance and its decorative media is crucial to the safe

performance of the appliance. See the owner's manual provided with the gas appliance for further information.

D. DO NOT install vented ﬁreplaces under any overhead construction.

DO NOT install unvented ﬁreplaces under any overhead construction that is less than 3 feet above the top of

the unit.

E. Ensure that the unit is installed on a hard and level surface.

F. This ﬁreplace must be installed so that the vent openings and surrounding area of the ﬁreplace remain

clear and free at all times.

G. Due to high temperatures, the unit must be located out of trafﬁc areas and away from combustibles.

A. The R.H.P. burner is a decorative gas appliance. It is not a cooking appliance.

B. SOLID FUEL MUST NOT BE BURNED in the unit.

C. When shutting the appliance down—be sure to TURN THE CONTROL VALVE FULLY OFF.

D. Children MUST be supervised when they are in the area of this unit.

E. DO NOT sit or place any part of the body, clothing, or other ﬂammable materials on or near the unit surround.

Children and adults should be alerted to the hazard of high surface temperatures and should stay away to

avoid burns or clothing ignition. DO NOT lean into the unit when lighting or when in use.

F. Every time you use the ﬁreplace and appliance, make sure that:

1. The area around the unit is clear and free from combustible materials, gasoline and other ﬂammable vapors

and liquids.

2. The vent openings and surrounding area of the ﬁreplace are clear and free at all times.

3. The hose is inspected (if applicable). See the SAFE USE & MAINTENANCE OF PROPANE-GAS CYLINDERS

section.

G. WARNING: HOT WHILE IN OPERATION AND FOLLOWING OPERATION. Serious injury can occur! DO

NOT throw trash, paper, or other ﬂammable materials into the unit. DO NOT leave in operation when unattended.

WARNING: DO NOT operate this ﬁreplace and appliance in the rain.

WARNING: DO NOT operate this ﬁreplace and appliance in high-wind conditions.

H. DO NOT continue using if you smell unusual odors, or have headaches, nausea, or dizziness.

I. DO NOT store any combustible materials, gasoline, and any other ﬂammable vapors/liquids in the vicinity of

the unit. Provide adequate clearance for servicing and operation.

J. Matches, paper, garbage, or any other material must not be thrown into the unit.

K. DO NOT use the appliance if any part of it has been underwater. Immediately call a qualiﬁed professional

service technician to inspect the appliance and to replace any part of the control system and any gas control

that has been underwater.

L. WARNING: Food cannot be consumed after coming in direct contact with the surface of the unit due to possible

contamination.

6

U

L

Fig. 6-1 type coupleur de ﬁl de point culminant d’I

Valve

de

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁl de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁl de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁg. 6-1).

Important: Avant d’employer le unité, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour

déceler les fuites. Arrêtez les valves de unité

et ouvrez la valve principale de cylindre, puis

vériﬁez les raccordements avec de l’eau

savonneux. Réparez toutes les fuites avant

d’allumer le unité.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le unité et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau ﬁssuré ou efﬁloché doit

être immédiatement remplacé.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁletées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Les bouteilles, les vannes et les tuyaux de propane doivent

être entretenus et inspectés avant chaque utilisation. Ils

doivent être remplacés en cas de dommages visibles. Si

le tuyau est coupé ou présente des signes d’abrasion ou

d’usure, il doit être remplacé avant utilisation (voir e.).

b. Cette unité, lorsqu'elle est utilisée avec une bouteille, doit

être connectée à une bouteille standard de gaz propane de

5 gallons (20 lb) équipée d'un dispositif anti-débordement

répertorié. L’appareil est obligatoire sur toutes les bouteilles

vendues depuis le 1er octobre 1998 aﬁn d’empêcher tout

remplissage excessif.

c. Les dimensions du cylindre doivent être d'environ 12 "(30,5 cm)

de diamètre et 18" (45,7 cm) de hauteur. Les bouteilles doivent

être construites et marquées conformément aux spéciﬁcations

du ministère des Transports (DOT) pour les bouteilles à gaz LP

ou à la norme relative aux bouteilles, sphères et tubes pour le

transport des marchandises dangereuses et à la Commission,

CAN / CSA-B339, selon le cas.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le montage du régulateur de pression et le ﬂexible (Fig. 6-1)

fourni avec cet appareil au gaz en plein air (modèles au

propane seulement) doit être utilisé. Assemblées d'origine et

régulateur de pression et le tuyau de remplacement doivent

être ceux spéciﬁés par le fabricant pour le raccordement d'un

dispositif de cylindre de liaison identiﬁée comme de type I

par le ANSI Z 21.58/CGA 1.6 (voir liste des pièces pour les

informations de commande).

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁnie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur de ﬁl de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁl

de point culminant sur la valve de cylindre. Tournez l’écrou de

1

2

3

4

e. Le régulateur de pression et l’ensemble de tuyau utilisé

doivent assortir les spéciﬁcations pour le type I par ANSI

Z 21.58/CGA 1.6 (voir la ﬁgue. 6-1).

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

7

U

L

Fig. 7-1 Type I Acme thread coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁtting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 7-1).

Important: Before using the unit, and after each time

the cylinder is removed and reattached,

check the hose for wear (see a.) and check

all connections for leaks. Turn off the unit

valves and open the main cylinder valve,

then check connections with soapy water.

Repair any leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and inspected before each use

of appliance. They must be replaced if there is any visible

damage. If hose is cut or shows excessive abrasion or wear,

it must be replaced before using appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with a listed overﬁlling prevention device. The

device has been required on all cylinders sold since

October 1,1998, to prevent overﬁlling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the U.S.

Department of Transportation (D.O.T.) Speciﬁcations for

LP-Gas Cylinders, or the Standard for Cylinders, Spheres,

and Tubes for Transportation of Dangerous Goods and

Commission, CAN/CSA-B339, as applicable.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 7-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁed by

the manufacturer for connection with a cylinder connecting

device identiﬁed as Type I by the ANSI Z 21.58/CGA 1.6

(see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with

a cylinder connection device, described as Type I in the

standard deﬁned in paragraph e. above. This device is

commonly described as an Acme thread coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁtting: Press the hand nut on the regulator

over the Acme thread ﬁtting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

e. The pressure regulator and hose assembly used must

match the speciﬁcation for Type I by ANSI Z 21.58/CGA

1.6 (see Fig. 7-1).

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

8

SPECIFICATIONS AND DIMENSIONS

Style Dimensions Weight / Pieces

Phoenix Fireplace (017 & 117) * 65" w x 36" d x 87" h 1100 lbs / 7 pcs

Grand Phoenix Fireplace (818 & 118) † 113" w x 36" d x 87" h 1400 lbs / 13 pcs

Mariposa Fireplace (073 & 173) * 65" w x 36" d x 67" h 970 lbs / 7 pcs

Grand Mariposa Fireplace (868 & 168) † 113" w x 36" d x 67" h 1300 lbs / 13 pcs

* Dimensions, Weight, & Pieces listed based upon a standard 16" Radiused Bullnose Hearth.

† Dimensions, Weight, & Pieces listed based upon an 113" Extended Bullnose Hearth.

Table 1 - Product Speciﬁcations

2" Recess Option

The above ﬁreplaces (except Grand models) are offered with a 2" recess option. This results in

certain areas of the ﬁreplace (ﬂat surfaces of the body and/or hearth) being "recessed" inward.

These reduced dimensions allow for the ﬁreplace to be customized with a ﬁnishing substrate

(i.e. tiles/stonework). Contact your local American Fyre Designs dealer for further details.

Depth

Height

Phoenix Fireplace

Width

Depth

Height

Grand Mariposa Fireplace

Width

Select Models

Shown

(your model may vary)

9

SPECIFICATIONS AND DIMENSIONS (cont.)

Style Dimensions *

16" Radiused Bullnose Hearth (01) 65" w x 36" d x 16" h

16" Rectangle Bullnose Hearth (02) 65" w x 36" d x 16" h

16" Roundover Hearth (03) 52" w x 32" d x 16" h

4" Roundover Hearth (04) 52" w x 32" d x 4" h

113" Extended Bullnose Hearth (05) 113" w x 36" d x 16" h

137" Extended Bullnose Hearth (06) 137" w x 36" d x 16" h

160" Extended Bullnose Hearth (07) 160" w x 36" d x 16" h

Corner Square Edge Hearth (08) Refer to drawing below

* See previous page for 2" Recess Option information.

Table 2 - Hearth Dimensions

16" Rectangle Bullnose Hearth 16" Radiused Bullnose Hearth

Corner Square Edge Hearth

Depth

Height

Width

Select Models

Shown

(your model may vary)

Depth

Height

Width

55"

54"

100"

33"

16"

130"

23"

10

SPECIFICATIONS AND DIMENSIONS (cont.)

This ﬁ replace is designed to be installed with an R.H.P. vented/unvented gas appliance. Below is a list of

the options available for each ﬁ replace type. The gas appliance is purchased separately. Contact your local

American Fyre Designs dealer when ordering.

Fireplace Styles Vented Burner Options Unvented Burner Options

Phoenix (017),

Grand Phoenix (818),

Mariposa Fireplace (073),

Grand Mariposa (868)

G45 STAINLESS STEEL

(Log Set or Glass Models)

Match-Lit Models: up to 24" burners

Valve Models: up to 18/20" burners

G22 STAINLESS STEEL

Match-Lit Models: up to 24" burners

Valve Models: up to 18" burners

-

Phoenix (117),

Grand Phoenix (118),

Mariposa Fireplace (173),

Grand Mariposa (168)

-

G10 STAINLESS STEEL

up to 24/30" burners with 24" log set

G21 STAINLESS STEEL

up to 24" burners

Table 3 - Fireplace Burner Options

The unit's marking label plate is located in the interior of the

ﬁ rebox. It hangs from a chain on the front inner wall (valve side).

Ensure the plate is placed behind the side liner during installation.

To view, simply reach in, access, then return once done.

For unvented models, the top liner must be moved to one side.

11

The dimensions shown below are MINIMUM CLEARANCES to maintain when you install the unit.

ALL CLEARANCES AND INFORMATION STATED HERE MUST BE MAINTAINED AND FOLLOWED.

MINIMUM CLEARANCES

Table 4 - Minimum Clearances

Floor must be a hard, level surface. Combustible materials permitted.

Description

Dimension

Vented Fireplace Unvented Fireplace

A. Side clearance

(from hearth extension to combustible construction)

6" 6"

B. Clearance above unit

Not permitted

36"

C. Clearance below unit 0" 0"

D.

Front clearance

(from hearth extension to combustible construction)

36" 36"

E. Rear clearance 6" 6"

B

A

C

E

A

D

TOOLS REQUIRED

The following are the minimum tools required for the installation of your unit. Additional tools may be required

for your individual installation.

• 2 (or more) assemblers recommended

• appropriate tools for gas supply install

• Phillips screwdriver

•

3

/

4

" open-end wrenches (2)

(or equivalent)

• 9

/

16

" open-end wrench

(or equivalent)

12

PARTS LIST

IMPORTANT

Remove all packing

material (including

any protective

coatings) and

discard prior to use.

• Your ﬁreplace is packaged onto 1 pallet.

• R.H.P. gas appliances are purchased and

packaged separately. Various models are

available.

• R.H.P. gas appliances and replacement parts

can be ordered from your local American Fyre

Designs dealer.

• Select models are illustrated

(your model may vary)

COMPONENTS

ARE HEAVY

HANDLE WITH CARE

IDENTIFICATION PARTS LIST

Phoenix (017, 117), Mariposa (073, 173)

1

2

4

3

Phoenix Vented Fireplace w/

16" Radiused Bullnose Hearth shown

(design of your model may slightly vary)

Item Description Qty.

1.

or

Hearth - 16" Radiused Bullnose

Hearth - 16" Rectangle Bullnose *

Hearth - 16" Roundover *

Hearth - 4" Roundover *

Hearth assembly - 113" Extended Bullnose *

Hearth assembly - 137" Extended Bullnose *

Hearth assembly - 160" Extended Bullnose *

Hearth assembly - Corner Square Edge *

1

2.

or

Firebox liners w/ shims - Vented (set of 4 liners and 2 shims)

Firebox liners w/ shims - Unvented (set of 5 liners and 2 shims) *

1

3. Body 1

4.

or

Chimney - Vented

Chimney - Unvented *

1

5. Bolt,

3

/

8

"-16 x 2.5" (pre-installed in body)* 2

6. Hardware kit - Body *

†

4

7.

or

Hardware kit - Hearth *

†

‡

113" Extended Bullnose

137" Extended Bullnose

160" Extended Bullnose

Corner Square Edge

8

* not shown

†

each kit contains: (1)

1

/

2

"-13 x 3.5" bolt, (1) nut, (2) washers

‡ only required / included with multi-piece large hearths

13

PARTS LIST (cont.)

IDENTIFICATION PARTS LIST

Grand Phoenix (818, 118)

1

2

3

1

4

Item Description Qty.

1.

or

Hearth assembly - 113" Extended Bullnose

Hearth assembly - 137" Extended Bullnose *

Hearth assembly - 160" Extended Bullnose *

1

2.

or

Firebox liners w/ shims - Vented (set of 4 liners and 2 shims)

Firebox liners w/ shims - Unvented (set of 5 liners and 2 shims) *

1

3. Body 1

4.

or

Chimney - Vented

Chimney - Unvented *

1

5. Bolt,

3

/

8

"-16 x 2.5" (pre-installed in body)* 2

6. Side wall - Main Piece 2

7. Side wall - Rear Piece 2

8. Hardware kit - Body*

†

8

9.

or

Hardware kit - Hearth*

†

113" Extended Bullnose

137" Extended Bullnose

160" Extended Bullnose

8

10. Concrete Phillips screw,

1

/

4

" x 1

3

/

4

" * 8

* not shown

†

each kit contains: (1)

1

/

2

"-13 x 3.5" bolt, (1) nut, (2) washers

Grand Phoenix Vented Fireplace w/

113" Extended Bullnose Hearth shown

(design of your model may slightly vary)

1

6

7

14

PARTS LIST (cont.)

IDENTIFICATION PARTS LIST

Grand Mariposa (868, 168)

1

2

3

1

4

Grand Mariposa Vented Fireplace w/

113" Extended Bullnose Hearth shown

(design of your model may slightly vary)

1

6

9

Item Description Qty.

1.

or

Hearth assembly - 113" Extended Bullnose

Hearth assembly - 137" Extended Bullnose *

Hearth assembly - 160" Extended Bullnose *

1

2.

or

Firebox liners w/ shims - Vented (set of 4 liners and 2 shims)

Firebox liners w/ shims - Unvented (set of 5 liners and 2 shims) *

1

3. Body 1

4.

or

Chimney - Vented

Chimney - Unvented *

1

5. Bolt,

3

/

8

"-16 x 2.5" (pre-installed in body)* 2

6. Side wall - Front 2

7. Side wall - Rear 2

8. Side wall - End 2

9. Side wall - Top 2

10. Hardware kit - Body*

†

14

11.

or

Hardware kit - Hearth*

†

113" Extended Bullnose

137" Extended Bullnose

160" Extended Bullnose

8

* not shown

†

each kit contains: (1)

1

/

2

"-13 x 3.5" bolt, (1) nut, (2) washers

8

7

8

INSTALLATION

15

IMPORTANT SAFETY INFORMATION

BE CAREFUL

If not installed and used correctly per these instructions,

this product can cause serious injury.

CAUTION: Installation and maintenance must be done by an NFI Certiﬁed or other qualiﬁed professional service

technician. Read these instructions before installing this ﬁreplace and the R.H.P. gas appliance. Be

sure you understand all safety precautions and warnings contained in this manual and the appliance

owner's manual.

A. FOR OUTDOOR USE ONLY.

B. When shutting the gas appliance down—be sure to TURN THE CONTROL VALVE OR KEY FULLY OFF.

C. WARNING: CARBON MONOXIDE POISONING MAY LEAD TO DEATH. DO NOT MODIFY THIS FIREPLACE

OR THE GAS APPLIANCE, EXCEPT AS PROVIDED FOR IN THE MANUALS. Any other change may be

dangerous. Improper installation or use of the ﬁreplace and R.H.P. gas appliance can cause serious injury or

death from ﬁre, burns, explosions, or carbon monoxide poisoning.

D. Check state and local codes to determine if the ﬁreplace and R.H.P. gas appliance are permitted in your

locality before installation.

E. Select models allow for an adjustable ﬂame height. THESE SETTINGS MUST ALWAYS BE HIGH ENOUGH

FOR THE FLAME TO BE CLEARLY VISIBLE. WHEN LIGHTING THE APPLIANCE, ALWAYS LIGHT ON HIGH.

FIREPLACE INSTALLATION

BEFORE YOU BEGIN

Important: Prior to installation ensure that all speciﬁcations, dimensions, and minimum clearances stated

in this manual are observed. You must read all warnings and safety information, and understand

all of the information in this manual. All installation requirements must be observed and met.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts speciﬁcally

approved with this unit may result in property damage or personal injury.

• Conﬁrm the installation site accommodates the ﬁreplace per the requirements in this manual.

• Be sure the gas supply (propane or natural) is turned off at its source.

• Remove all packing material (including any protective coatings) and discard prior to installation.

LOCATION

While following all requirements and safety information in this manual (see MINIMUM CLEARANCES section);

determine and prepare the location of the ﬁreplace (a hard and level surface).

Note: For ﬁreplaces, a combustible surface is permitted.

Important: The gas supply must be considered when determining the location of the unit. See GAS

SUPPLY SETUP section for details.

ASSEMBLY REQUIRES TWO OR MORE PEOPLE.

EXERCISE EXTREME CARE DURING ASSEMBLY AND INSTALLATION.

INSTALLATION

16

FIREPLACE INSTALLATION (cont.)

FIREPLACE ASSEMBLY - OVERVIEW

CAUTION: Fireplace components are heavy. CAREFULLY handle all components during assembly.

• Fig. 16-1 provides an overall orientation and bolt assembly detail for the ﬁreplace.

(Phoenix w/ 16" Radiused Bullnose Hearth shown. Mariposa and Grand models assemble in a similar manner.

Assembly may slightly vary depending on model and hearth selected.)

• Grand models have the addition of side walls, which are addressed in the following step-by-step section.

• This section is just an overview, refer to the following step-by-step section for complete assembly

and installation details.

Fig. 16-1

Overall Orientation

Phoenix Fireplace w/

16" Radiused Bullnose

Hearth shown

ASSEMBLY / INSTALL OVERVIEW

1. Place / Assemble hearth *

2. Assemble body

3. Connect gas (not shown)

4. Assemble side walls

(Grand models only, not shown)

5. Install ﬁrebox liners and shims

6. Assemble chimney

7. Install burner (not shown)

2

5

6

1*

* One-piece hearth shown here.

Multi-piece hearths require assembly.

17

FIREPLACE INSTALLATION (cont.)

GAS SUPPLY SETUP (if applicable)

For Natural or Household Propane Gas Supply:

The gas supply is to be brought up from beneath the hearth

or directly behind it. Your individual installation may vary.

Observe the National Fuel Gas Code and all local codes.

1. Route the gas supply into the area that the hearth will

rest over.

Important: Locate the gas supply line out of pathways

where people may trip over it or in areas

where the line may be subject to accidental

damage (if applicable).

Note: A shut-off valve (not included) in the gas line is

optional. It can be installed within 6 feet of the unit.

Use a pipe joint compound resistant to all gasses on

all male ﬁttings except ﬂare ﬁttings.

FIREPLACE ASSEMBLY - STEP BY STEP

CAUTION: Fireplace components are heavy.

CAREFULLY handle all components during

assembly.

Important: DO NOT overtighten (to avoid damage to the

unit).

A Phoenix Fireplace with a 16" Radiused Bullnose Hearth

is primarily depicted here. Your assembly may slightly vary

depending on model and hearth selected.

Hearth

1. CAREFULLY place the hearth or hearth pieces in an

appropriate location (refer back to the LOCATION section

if needed).

For one-piece hearths, step 2-5 are not applicable:

proceed to the following section.

2. Arrange the hearth pieces in their proper position. Then

insert the bolts and washers into the outer pieces of the

hearth as shown in Fig. 17-1.

3. Carefully slide the left outer-piece against the center

piece while aligning the pilot holes. Then reach into

the center hearth (through access opening), place the

washers and nuts, and hand tighten. See Fig. 17-2.

4. Use a

3

/

4

" open end wrench (or equivalent) to apply a

1/4 turn to secure.

Important: DO NOT overtighten (to avoid damage to the

unit).

5. Repeat for the right outer-piece.

Fig. 17-1 Assemble hearth - arrange (if required)

Hardware:

Bolts x 8

Washers x 8

3 piece

hearth shown

Fig. 17-2 Assemble hearth - slide together & fasten

Fig. 17-3 Hearth assembled

Hardware:

Nuts x 8

Washers x 8

An alternative method for access is to CAREFULLY tilt

the hearth pieces on their back. Use 2x4s as wedges to

ensure the pieces remain upright during the procedure.

Use extreme care when lifting/lowering the pieces to

prevent injury or damage. It is recommended to rest

cardboard over the work space (to prevent damage).

Remove after assembly.

B

C

Slide

together

Fasten with

nuts & washers

A

Insert bolts

& washers

(Assemble all pieces)

18

FIREPLACE INSTALLATION (cont.)

Body

1. Place the body piece on top of the hearth. Carefully

align the pilot holes, and insert the hardware in the order

shown in Fig. 18-1. Hand tighten, then use two

3

/

4

" open

end wrenches (or equivalent) to fasten.

Note: It is recommended to rest cardboard on the hearth

when positioning the body (to prevent damage to the

hearth surface). Remove once positioned.

Connect Gas Supply

Important: Before installation, be sure the gas supply

(propane or natural) is turned off at its source.

The ﬁreplace has a key valve pre-installed on either the right

or left side of the ﬁreplace. For ﬁreplaces that have the rear

gas line option, a

1

/

2

" rigid gas pipe is pre-installed to the

valve and protrudes out of the rear of the unit.

(A ﬂex connector is pre-attached to the key valve on the

interior of the ﬁreplace. An R.H.P. burner is to be connected

to it at a later time.)

1. Route the gas supply (natural gas, household propane,

or from an L.P. Cylinder) to the unit as applicable.

For rear installs, see Fig. 18-2.

For underneath installs, see Fig. 18-3.

Observe all codes and ensur e all appropriate connections

are used to properly connect the gas supply. Apply only joint

compounds that are resistant to all gasses to all male pipe

ﬁttings except ﬂare ﬁttings. Make sure to tighten every joint

securely and properly leak test at all connections.

Important: This fireplace does not accommodate

propane cylinders. If a cylinder is used it must

be located in a safe location.

Tank tables are available from American

Fyre Designs. Contact your local dealer for

ordering information.

Fig. 18-2 Route gas supply (rear install)

(key valve

location

may vary)

Fig. 18-3 Route gas supply (underneath install)

(key valve

location

may vary)

Key valve

Flex

connector

Connect

here

Connect here

(from below)

Key valve

Flex

connector

Installation continued on next page

Fig. 18-1 Assemble body

Hardware:

Bolts x 4

Nuts x 4

Washers x 8

19

FIREPLACE INSTALLATION (cont.)

For standard models proceed to the LINERS section.

For Grand models, continue on to the following

section.

MARIPOSA Grand Models ONLY - Side Walls

Note: For Phoenix models, see next page for side wall

assembly.

1. Locate the four pieces required to assemble one complete

side wall.

2. Place the rear side-wall piece beside the ﬁ replace body

as shown. Carefully align the pilot holes, and repeat the

hardware installation process. See Fig. 19-1.

3. Place the front side-wall piece beside the ﬁ replace body

as shown. Carefully align the pilot holes, and repeat the

hardware installation process. See Fig. 19-2.

4. Place the end side-wall piece against the front and rear

side-walls as shown in Fig. 19-3 (no hardware required).

5. Slide the top side-wall piece onto the front and rear side-

walls as shown in Fig. 19-4 (no hardware required). This

will secure the entire side wall.

6. Repeat assembly for the opposite side.

7. The seams of the side wall pieces must be ﬁ nished

with a sanded grout (not included) according to color

preference (see Fig. 19-5). The grout can be purchased

at a local hardware store. Follow all instructions provided

with the grout.

Installation continued on next page

Fig. 19-1 Assemble rear side-wall (skip if n/a)

Fig. 19-2 Assemble front side-wall (skip if n/a)

Fig. 19-3 Assemble end side-wall (skip if n/a)

Fig. 19-4 Assemble top side-wall (skip if n/a)

MARIPOSA Grand

Models Only:

Side Walls

Hardware:

Bolts x 3

Nuts x 3

Washers x 6

Hardware:

Bolts x 2

Nuts x 2

Washers x 4

Fig. 19-5 Grout seams (skip if n/a)

Grout seams

20

FIREPLACE INSTALLATION (cont.)

PHOENIX Grand Models ONLY - Side Walls

1. Place one main side-wall piece beside the ﬁ replace body

as shown. Carefully align the pilot holes, and repeat the

hardware installation process. See Fig. 20-1.

2. Each rear side-wall piece is marked to align the detail.

Place the correct rear side-wall piece in position against

the rear of the main piece, then fasten using a Phillips

screwdriver and the supplied concrete screws (see Fig.

20-2).

3. Repeat assembly for the opposite side.

Liners

1. Install the ﬁ rebox liners into the interior of the ﬁ rebox in

the order shown in Fig. 20-3:

• The bottom and rear liners have grooves to assist in

placement.

• The two shims "D" are to be wedged between liner

"B" and the rear wall by hand as shown. The shims

secure the liner set in place.

• Be sure to pull the ﬂ ex connector inside of the ﬁ replace

body through the liner and into the open interior of the

ﬁ rebox (for later R.H.P. burner installation).

• Ensure the unit's marking label plate is placed behind

the side liner during installation. It is located in the

interior of the ﬁ rebox, and hangs from a chain on the

front inner wall (valve side).

• For Unvented Fireplaces: An additional liner "E"

exists and is to be installed onto the top of the ﬁ rebox

(through the top of the body piece).

Note: The liners rest in place. No hardware is required.

Fig. 20-3 Install ﬁ rebox liners

A

B

C

E

Be sure to pull ﬂ ex

connector through liner

Unvented ﬁ replaces

contain a liner for the

top of the ﬁ rebox.

D

Installation continued on next page

Fig. 20-1 Assemble side-wall (skip if n/a)

Fig. 20-2 Assemble rear side-wall (skip if n/a)

PHOENIX Grand

Models Only:

Side Walls

Hardware:

Bolts x 2

Nuts x 2

Washers x 4

Hardware:

1/4" x 1 3/4"

Concrete

Screws

(x 4)

Rear view

Align detail

La page charge ...

R.H. Peterson American Fyre Designs Unvented Series Installation & Owner's Manual

Ce manuel convient également à

R.H. Peterson American Fyre Designs Unvented Series Installation & Owner's Manual

dans d''autres langues

Documents connexes

Autres documents