Automate 7856V Le manuel du propriétaire

Table of Contents

Congratulations ..........................................................................1

Important Information ..................................................................2

Government Regulations and Safety Information .....................2

Your Warranty ..................................................................... 2

Replacement Remote Controls ................................................2

Introduction .................................................................................3

2-Way LED Remote Control ...................................................3

Control Center ..................................................................... 3

Using the System .......................................................................... 4

Commands and Conﬁrmations ..............................................4

Performing Commands .........................................................4

Remote Control Command Table ....................................................5

Basic Commands .........................................................................6

Arm/Lock ...........................................................................6

Panic Mode ........................................................................6

AUX/Trunk .......................................................................... 7

Remote Start ........................................................................7

Valet Mode .........................................................................8

Battery Information .....................................................................10

Low Battery .......................................................................10

Battery Information (1-way) .........................................................11

Battery Replacement ........................................................... 11

Battery Disposal ................................................................11

Patent Information ......................................................................12

Government Regulations .............................................................13

Warning! Safety First .................................................................. 15

Limited Lifetime Consumer Warranty .............................................18

1

Congratulations

Congratulations on the purchase of your state-of-the-art Directed

Digital System. Reading this Owner’s Guide prior to using your

system will help maximize the use its many features. For more

information please visit us online (see back cover for URL). For

any additional questions please contact your authorized Directed

dealer or Directed at 1-800-753-0600. Additional support is also

available at: http://support.directed.com.

Note: Your system is conﬁgurable and may or may not include

features such as remote start or security. This guide also covers

optional features which may not be applicable to your system.

Please speak with your installation technician to ﬁnd out which

features are applicable.

2

Important Information

Government Regulations and Safety Information

Read the Government Regulations and Warning!

Safety First sections of this manual prior to operating

this system.

WARNING! Failure to heed this information can result

in death, personal injury or property damage and may

also result in the illegal use of the system beyond its

intended purpose.

Your Warranty

Your system comes with a warranty. The warranty terms are de-

tailed at the end of this guide. Make sure that you receive the

proof of purchase from your dealer, indicating the product was

installed by an authorized Directed dealer.

Replacement Remote Controls

Please see your authorized dealer or visit us at

www.directedstore.com to order additional remote controls. Re-

mote control RPN (Replacement Part Number) are typically found

on the back of the device.

3

Introduction

2-Way LED Remote Control

Feature Description

Internal Antenna Used for transmitting and receiving information.

Command Buttons (4)

Used to perform Arming, Disarming, Auxiliary channel

and Remote Start commands.

Function Button

Used to access function levels for commands, conﬁgu-

ration menus for programming, Car Selection, and to

request reports, as well as 2-way remote battery voltage.

Function Level/Conﬁr-

mation LEDs

Each button has an associated LED next to it that are

active during related operations. These LED’s are labeled

respectively as: Arm LED, Disarm LED, Remote Start LED

and AUX LED.

Micro-USB Port

The USB cable plugs into this port to charge the battery

(located on remote control side).

Control Center

Antenna

LED

Button

The Control Center sends and receives commands or messages to

and from the system. It consists of:

• The antenna, for system communication.

• The Status LED, as a visual indicator of the system’s status.

• Valet button, for accessing various feature, programming,

and reporting functions of the system.

4

Using the System

Commands and Conﬁrmations

This quick reference guide only covers basic features. Advanced

features and more information on your system can be found in

the full on-line guide. Please visit us on-line, and search using your

system’s model number (found on the front cover, the URL is located

on the back cover):

The remote control sends commands that control the features of

your system. Only the 2-way remote control displays a conﬁrma-

tion of the command using text, icons and tones, the 1-way does

not.

If a command is sent for a feature that is not included in your

system or not available (example: runtime reset when remote start

is off) the remote control displays an alert by text, icon and tone.

If the system doesn’t respond to a command the remote control dis-

plays an alert by icon and tone. You may be too far from your ve-

hicle or “out-of-range”. Change locations and retry until successful.

Performing Commands

Press any command button directly to send one of the Basic com-

mands to your system.

Press the

button 1-4 times before pressing a command button to

send an Advanced command.

The following Remote Control Command table deﬁnes the button

press actions required for the Basic and Advanced commands that

may be available for your system.

5

Remote Control Command Table

Level

Button

Basic Com-

mands

x1

LEVEL 1

x1

LEVEL 2

x1

LEVEL 3

x1

LEVEL 4

Arm/Lock

(Panic)

Silent Arm/

Lock

Sensor

Bypass*

Sensor

Silent

Mode

Arm*

Full Silent

Mode

Arm*

Disarm/Unlock

Silent

Disarm

/Unlock

Alarm/

System

Valet

Car Finder

Start

Valet**

Remote Start**

Runtime

Reset**

Timer

Start**

Smart

Start**

Defog-

ger**

AUX

AUX/Trunk AUX 1 AUX 2 AUX 3 AUX 4

Advance Level,

Change Car

(Hold 3 sec.),

Enter Programming

(Hold 8 sec.)

Temperature

Check

(2-way

only)

Runtime

Remaining

(2-way

only)**

Alarm Re-

port (2-way

only)*

+

AUX

Combo Valet (Both

Start and Alarm/

System Valet)***

* Security commands are available only on systems with alarm

features.

** Remote Start commands are available only on systems with

remote start features.

*** Combo Valet commands are available only on select sys-

tems.

2-WAY LED Remote Battery Level - To check the battery level,

press the

button ﬁve times. The LEDs turn on, bottom to top to

indicate the current battery charge.

6

Example: Performing an advanced command, Silent Arm/Lock

1. Press the

button once to access Function Level 1.

2. Then, press the

button immediately to send the command.

3. The system arms/locks silently and the remote control con-

ﬁrms by LED, but without tones.

Basic Commands

Arm/Lock

Press and release

The vehicle doors lock, siren/horn sound, parking lights ﬂash, and

alarm* features are enabled. The 2-way remote control conﬁrms

by using LED and tone.

If an alarm zone is active (e.g. door is open) an alert message

will follow. If a Valet mode is enabled the 2-way remote control

conﬁrms by using LED and tones accordingly.

Panic Mode

Press and hold

The system arms/locks, then two seconds later begins the Panic

output. The 2-way remote control conﬁrms by using LED and tones.

Press the

or button to stop the panic output anytime.

Disarm/Unlock

Press and release

The vehicle doors unlock, siren/horn sound, parking lights ﬂash,

and alarm* features are disabled. The 2-way remote control con-

ﬁrms by using LED and tone.

If an alarm trigger has occurred an alert message will follow. If a

Valet mode is enabled the 2-way remote control conﬁrms by using

LED and tones accordingly.

7

AUX/Trunk

Press and hold AUX.

The trunk opens after two seconds (if connected) and the 2-way

remote control conﬁrms by using LED and tones.

* Available for systems with security features only.

Remote Start

Press and release

The remote start turns on and the 2-way remote control conﬁrms by

LED or tone and then, ﬂashes the Remote Start LED while Remote

Start is on. If the remote start is on when the command is sent then

it turns off and the 2-way remote control conﬁrms by using LED

and tone.

If the remote start fails to turn on, the 2-way remote control will

display an alert by LED and tone, and the vehicle parking lights

will ﬂash to indicate the cause. Refer to the following table for the

likely cause.

Alert Conditions:

Parking Light

Flashes*

Possible Cause Solution

5 Brake ON Release Foot Brake.

6 Hood Open Close Hood.

7

After performing Remote Start

command MTS not enabled.

Enabled MTS Mode.

9 Start/system Valet on Turn Start Valet off

8

Valet Mode

Remote Valet Modes

The Valet commands in the remote command table turn on/off

the Alarm Valet/System Valet, Start Valet, or Combo Valet Modes

(both Alarm & Start Valet).

Alarm Valet/System Valet

The Alarm Valet mode will disable included alarm features when

armed/locked. It also disables any passive arm/lock settings

if programmed on. The 2-way remote control conﬁrms by using

LED and tones.

System Valet

On select models, the System Valet will disable both alarm and

remote start features. These systems do not have separate alarm

valet or start valet functions.

Start Valet

The Start Valet mode will disable remote start features until turned

off. The 2-way remote control conﬁrms by using LED and tones.

Combo Valet

The Combo Valet command is used to turn on/off both Alarm

Valet and Start Valet together.

• If both Valets are off then both will be turned on.

• If one or both Valets are on, then they will be turned off.

The 2-way remote control conﬁrms by using LED and tones.

9

Manual Valet Modes

Use the following routine to manually turn on/off the Valet Modes,

turning both on manually achieves Combo Valet:

1. Turn the ignition ON and then OFF.

• Alarm/System Valet:

Press and release the Valet button once.

Alarm Valet will turn on/off accordingly. The Control Center

LED will be on while Alarm Valet is on and will be off when

Alarm Valet is off. The siren/horn also sounds to conﬁrm.

If your product has System Valet: Along with the Control

Center LED being on, the parking lights will ﬂash nine times

in rapid succession when turned on, and nine times in slow

succession when turned off.

• Start Valet:

Press and hold the Valet button for ﬁve seconds.

The parking lights ﬂash nine times in rapid succession when

turned on, and nine times in slow succession when turned

off. The 2-way remote control conﬁrms by using LED and

tones.

Emergency Override

The following procedure Disarms the system when a programmed

remote is not available. Number of presses__________

1. Turn the ignition ON.

2. Press the Valet button the correct number of times (the default

is 1 press). After a few seconds the siren output ceases and

the system is Disarmed.

10

Battery Information

The Responder LED remote control is powered by an internal

rechargeable battery that can be serviced only through an au-

thorized Directed dealer. The information and precautions in this

section can help maximize your battery’s life and usage in provid-

ing your Responder LED remote control with many years of trouble

free operation.

To charge the battery, connect the provided USB cable between

the remote control and a computer with a USB port. The LED ﬂash-

es to indicate the remote control is charging. Once full the transmit

LED will ﬂash once every two seconds.

Warnings! NEVER use a cable other than the one pro-

vided or plug into an unspeciﬁed source. Injury, severe

damage or explosion may occur when connected to

any other products or used in a way not intended.

Charging the battery when the temperature is below

32°F (0°C) or above 113°F (45°C) may cause

severe battery damage and/or reduce battery life.

Avoid placing the remote control in areas exposed to

extreme cold or heat (direct sunlight) when charging

the battery.

Low Battery

The remote controls constantly monitor the battery’s voltage level.

If low, a low voltage alert is conﬁrmed by LED and/or tones. The

systems siren/horn will also emit one extra chirp after disarming to

alert of a low battery level condition.

To check the battery level, press the

button ﬁve times. The LEDs

turn on, bottom to top to indicate the current battery charge.

11

Battery Information (1-way)

The 1-way remote controls are powered by one 3V coin cell lith-

ium battery (RPN* CR-2032) that can be purchased at most re-

tailers. When the battery begins to weaken, the operating range

will be reduced.

Battery Replacement

1. Unscrew the hardware on unit rear and remove from hous-

ing (if present).

2. Use a small ﬂat blade screwdriver and insert it into the slot

located along the bottom of the remote, near the key ring.

Carefully pry open the case.

3. Gently slide out the used battery/batteries to remove it from

the holding clip. Orient the new battery for the correct polar-

ity and insert into holding clip.

4. Realign the case parts and snap together by pressing ﬁrmly

and evenly on the front and back. Reinstall screw (if present).

Battery Disposal

Directed cares about the environment. If you need to

dispose of the battery, please do so in accordance with

your municipal requirements for battery disposal.

* RPN (Replcement Part Number).

12

Patent Information

This product is covered by one or more of the following United

States patents:

Remote Start Patents:

5,349,931; 5,872,519; 5,914,667; 5,952,933;

5,945,936; 5,990,786; 6,028,372; 6,467,448;

6,561,151; 7,191,053; 7,483,783

Vehicle Security Patents:

5,467,070; 5,532,670; 5,534,845; 5,563,576;

5,646,591; 5,650,774; 5,673,017; 5,712,638;

5,872,519; 5,914,667; 5,952,933; 5,945,936;

5,990,786; 6,028,505; 6,452,484

Other patents pending.

13

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates and

can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television, which can be determined by turning

the equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

Remote Controls

To satisfy FCC RF exposure compliance requirements, this device should

be used in hand-held, hand operated configurations only. The device and

its antenna must maintain a separation distance of 20 cm or more from

the person’s body, except for the hand and wrists, to satisfy RF exposure

compliance. This device is designed to be used in a person’s hands and

its operating configurations do not support normal transmissions while it is

carried in pockets or holsters next to a person’s body.

Control Center

To satisfy FCC RF exposure compliance requirements, the device and

its antenna must maintain a separation distance of 20 cm or more from

the person’s body, except for the hand and wrists, to satisfy RF exposure

compliance.

14

This device complies with the Industry Canada Radio Standards

Specification RSS 210. Its use is authorized only on a no-interference,

no-protection basis; in other words, this device must not be used if it is

determined that it causes harmful interference to services authorized by

IC. In addition, the user of this device must accept any radio interference

that may be received, even if this interference could affect the operation

of the device.

WARNING!

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate

this device.

15

Warning! Safety First

Please read the safety warnings below before proceed-

ing. Improper use of the product may be dangerous

or illegal.

Installation

Due to the complexity of this system, installation of this product must only be

performed by an authorized Directed dealer. If you have any questions, ask

your retailer or contact Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command

signal from the remote control transmitter. Therefore, never operate the

system in an enclosed area or partially enclosed area without ventilation

(such as a garage). When parking in an enclosed or partially enclosed

area or when having the vehicle serviced, the remote start system must be

disabled using the “Start Valet” procedure found under “Valet Modes” in

this guide. It is the user’s sole responsibility to properly handle and keep

out of reach from children all remote control remote controls to assure

that the system does not unintentionally remote start the vehicle. IT IS

RECOMMENDED THAT THE USER INSTALL A CARBON MONOXIDE

DETECTOR IN THE LIVING AREAS ADJACENT TO THE VEHICLE. ALL

DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED

OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST BE CLOSED

AT ALL TIMES. These precautions are the sole responsibility of the user.

Manual Transmission Vehicles

Remote starters on manual transmission vehicles operate differently than

those with automatic transmission because you must leave your car in

neutral. You must read this Owner’s Guide to familiarize yourself with

the proper procedures regarding manual transmission remote starters. If

you have any questions, ask your authorized Directed dealer or contact

Directed at 1-800-753-0600.

16

Before remote starting a manual transmission vehicle, be sure to:

• Leave the vehicle in neutral and be sure no one is standing in front

or behind the vehicle.

• Only remote start on a flat surface

• Have the parking brake fully engaged

WARNING!

It is the responsibility of the owner to ensure the parking/

emergency brake properly functions. Failure to do so can result in personal

injury or property damage. We recommend the owner have the parking /

emergency brake system inspected and adjusted by a qualified automotive

shop biannually.

Use of this product in a manner contrary to its intended mode of operation

may result in property damage, personal injury, or death. (1) Never

remotely start the vehicle with the vehicle in gear, and (2) Never remotely

start the vehicle with the keys in the ignition. The user must also have

the neutral safety feature of the vehicle periodically checked, wherein the

vehicle must not remotely start while the car is in gear. This testing should be

performed by an authorized Directed dealer in accordance with the Safety

Check outlined in the product installation guide. If the vehicle starts in gear,

cease remote start operation immediately and consult with the authorized

Directed dealer to fix the problem.

After the remote start module has been installed, contact your authorized

dealer to have him or her test the remote start module by performing the

Safety Check outlined in the product installation guide. If the vehicle starts

when performing the Neutral Safety Shutdown Circuit test, the remote

start unit has not been properly installed. The remote start module must be

removed or the installer must properly reinstall the remote start system so that

the vehicle does not start in gear. All installations must be performed by an

authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS

IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION.

OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS

MAY CAUSE THE VEHICLE TO UNEXPECTEDLY LUNGE FORWARD

RESULTING IN PROPERTY DAMAGE OR SERIOUS PERSONAL INJURY

INCLUDING DEATH. YOU MUST IMMEDIATELY CEASE THE USE OF

17

THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED DIRECTED

DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START

MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR

INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel injected vehicles only. Use of this product in

a standard transmission vehicle must be in strict accordance with this guide.

This product should not be installed in any convertible vehicles, soft or

hard top with a manual transmission. Installation in such vehicles may pose

certain risk.

Interference

All radio devices are subject to interference which could affect proper

performance.

Upgrades

Any upgrades to this product must be performed by an authorized Directed

dealer. Do not attempt to perform any unauthorized modifications to this

product.

Water/Heat Resistance

This product is not designed to be water and/or heat-resistant. Please take

care to keep this product dry and away from heat sources. Any damage

from water or heat will void the warranty.

18

Limited Lifetime Consumer Warranty

Directed Electronics. (“Directed”) promises to the original purchaser to

repair or replace (at Directed’s election) with a comparable reconditioned

model any Directed unit (hereafter the “unit”), excluding without limitation

the siren, the remote transmitters, the associated sensors and accessories,

which proves to be defective in workmanship or material under reasonable

use during the lifetime of the vehicle provided the following conditions

are met: the unit was purchased from an authorized Directed dealer, the

unit was professionally installed and serviced by an authorized Directed

dealer; the unit will be profession¬ally reinstalled in the vehicle in which

it was originally installed by an authorized Directed dealer; and the unit

is returned to Directed, shipping prepaid with a legible copy of the bill of

sale or other dated proof of purchase bearing the following information:

consumer’s name, telephone number and address; the authorized dealers

name, telephone number and address; complete product description,

including accessories; the year, make and model of the vehicle; vehicle

license number and vehicle identification number. All components other

than the unit, including without limitation the siren, the remote transmitters

and the associated sensors and accessories, carry a one-year warranty

from the date of purchase of the same. ALL PRODUCTS RECEIVED BY

DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF PURCHASE

FROM AN AUTHORIZED DEALER WILL BE DENIED. This warranty is

non-transferable and is automatically void if: the unit’s date code or serial

number is defaced, missing or altered; the unit has been modified or used

in a manner contrary to its intended purpose; the unit has been damaged

by accident, unreasonable use, neglect, improper service, installation or

other causes not arising out of defects in materials or construction. The

warranty does not cover damage to the unit caused by installation or

removal of the unit. Directed, in its sole discretion, will determine what

constitutes excessive damage and may refuse the return of any unit with

excessive damage.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES,

INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED

WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR

PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF

INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED

NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO

La page charge ...

Automate 7856V Le manuel du propriétaire

Ce manuel convient également à

Automate 7856V Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents