Ryobi RY40255-BLW Mode d'emploi

Marque: Ryobi

Modèle: RY40255-BLW

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Su cabezal motor ha sido diseñada y fabricada de conformidad

con las estrictas normas para brindar fiabilidad, facilidad de uso

y seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

Le bloc-moteur a été conçue et fabriquée conformément à

nos strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenue, elle vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your power head has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

OPERATOR’S MANUAL

MANUEL D’UTILISATION/MANUAL DEL OPERADOR

40 VOLT POWER HEAD

40V BLOC MOTEUR

40V CABEZAL MOTOR

RY40002

ALL VERSIONS

TOUTES LES VERSIONS

TODAS LAS VERSIONES

BATTERIES AND CHARGERS SOLD SEPARATELY

PILES ET CHARGEUR VENDUS SÉPARÉMENT

LAS BATERÍAS Y EL CARGADOR SE VENDEN POR SEPARADO

See this fold-out section for all the figures

referenced in the operator’s manual.

Voir que cette section d’encart pour toutes les

figures a adressé dans le manuel d’utilisation.

Vea esta sección de la página desplegable para

todas las figuras mencionó en el manual del operador.

A - Switch trigger (gâchette, gatillo del interruptor)

B - Knob (bouton, perilla)

C - Coupler (coupleur, acoplador)

D - Rear handle (poignée arrière, mango trasero)

Fig. 1

Fig. 2

A - Button (bouton, botón)

B - Guide recess (logement guide, hueco guía)

C - Coupler (coupleur, acoplador)

D - Power head shaft (arbre du bloc moteur, eje

del cabezal motor)

E - Knob (bouton, perilla)

F - Positioning hole (trou de positionnement,

orificio de posicionamiento)

G - Attachment shaft (arbre d’accessoire, eje del

aditamento)

Fig. 3

A - Front handle (poignée avant, mango

delantero)

B - Wing bolt (boulon à oreilles, perno de

mariposa)

C - Washer (rondelle, arandela)

Fig. 4

A - Battery pack (bloc-piles, paquete de

baterías)

B - Latch (loquet, pestillo)

E - Adjustable front handle (poignée avant réglable, mango delantero

ajustable)

F - Trigger lock-out (gâchette avec verrou, gatillo con seguro)

iii

Fig. 8

A - Trigger lock-out (gâchette avec verrou,

gatillo con seguro)

B - Switch trigger (gâchette, gatillo del

interruptor)

Fig. 6

Fig. 5

A - Knob (bouton, perilla)

B - Adjustable front handle (poignée avant

réglable, mango delantero ajustable)

Fig. 9

Fig. 10

Fig. 11

Fig. 7

PROPER EDGER ATTACHMENT

OPERATING POSITION

ACCESSOIRE COUPE-BORDURES

POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL

ACCESORIO PARA CORTAR BORDES

PROPER BLOWER ATTACHMENT

OPERATING POSITION

ACCESSOIRE SOUFFLANTE

POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL

MANEJO DE ADITAMENTO PARA SOPLADOR

PROPER CULTIVATOR ATTACHMENT

OPERATING POSITION

ACCESSOIRE CULTIVATEUR POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL

MANEJO DE ADITAMENTO PARA CULTIVAR

PROPER CURVED SHAFT TRIMMER

ATTACHMENT OPERATING POSITION

ACCESSOIRE TAILLE-BORDURES À ARBRE

COURBÉE POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO DE ADITA-

MENTO PARA RECORTADORA DE EJE CURVO

PROPER STRAIGHT SHAFT TRIMMER

ATTACHMENT OPERATING POSITION

ACCESSOIRE TAILLE-BORDURES À ARBRE DROIT

POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO DE ADITA-

MENTO PARA RECORTADORA DE EJE RECTO

2 — English

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................3-4

Instructions importantes concernant la securite / Instrucciones de seguidad importantes

Symbols ............................................................................................................................................................................ 5

Symboles / Símbolos

 Features ............................................................................................................................................................................6

Caractéristiques / Características

 Assembly .......................................................................................................................................................................6-7

Assemblage / Armado

 Operation ....................................................................................................................................................................... 8-9

Utilisation / Funcionamiento

 Maintenance ..................................................................................................................................................................... 9

Entretien / Mantenimiento

 Troubleshooting ................................................................................................................................................................ 9

Dépannage / Corrección de problemas

 Warranty ......................................................................................................................................................................... 10

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

3 — English

WARNING!

When using electric gardening appliances, basic safety

precautions should always be followed to reduce the risk

of fire, electric shock and personal injury.

READ ALL INSTRUCTIONS

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use this

unit.

Check the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which

can be thrown or become entangled in the machine.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Following this rule will reduce

the risk of serious personal injury.

Use Safety Glasses – Always use face or dust mask if

operation is dusty.

Protect your lungs. Wear a face or dust mask if the

operation is dusty. Following this rule will reduce the risk

of serious personal injury.

 Dress Properly – Use of rubber gloves and substantial

footwear is recommended when working outdoors. Wear

heavy, long pants, long sleeves, boots, and gloves. Do

not wear loose fitting clothing, short pants, sandals, or

go barefoot. Do not wear loose clothing or jewelry. They

can be caught in moving parts. Secure long hair above

shoulder level to prevent entanglement in moving parts.

Keep children away – Keep all bystanders, children, and

pets at least 50 ft. away.

Stay alert – Watch what you are doing. Use common sense.

Do not operate this unit when you are tired, ill, upset, or

under the influence of alcohol, drugs, or medication.

Do not operate in poor lighting.

Keep all parts of your body away from any moving part.

Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases, or

dust. Power tools create sparks which may ignite the

dust or fumes.

Avoid body contact with grounded surfaces such as

pipes, radiators, ranges, and refrigerators. There is an

increased risk of electric shock if your body is grounded.

Avoid Dangerous Environments – Don’t expose appliance

to rain or wet conditions. Water entering an appliance will

increase the risk of electric shock.

IMPORTANT SAFETY INSTRUCTIONS

Use Right Appliance – Do not use appliance for any job

except that for which it is intended. Do not force tool.

Use the correct tool for your application. The correct tool

will do the job better and safer at the rate for which it is

designed.

Don’t Force Appliance – It will do the job better and with

less likelihood of a risk of injury at the rate for which it

was designed.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

Do not overreach – Keep firm footing and balance.

Overreaching can result in loss of balance.

Avoid accidental starting – Be sure switch trigger is in

the locked or off position before inserting battery pack.

Carrying tools with your finger on the switch trigger or

inserting the battery pack into a tool with the switch on

invites accidents.

Do not use tool if switch trigger does not turn it on or off.

Any tool that cannot be controlled with the switch trigger

is dangerous and must be repaired.

Disconnect power head – Disconnect battery pack from

the appliance before storing, servicing, or changing

accessories such as cutting line. Such preventive safety

measures reduce the risk of starting the tool accidentally.

Use only identical manufacturer’s replacement parts and

accessories. Use of any other parts may create a hazard

or cause product damage.

Maintain appliance with care – Replace string head if

cracked, chipped, or damaged in any way. Be sure the

string head is properly installed and securely fastened.

Failure to do so can cause serious injury. Follow instruc-

tions for lubrication and changing accessories. Inspect

charger cord periodically and, if damaged, have it replaced.

Keep power head handles dry, clean, and free from grease

and oil.

Check Damaged Parts – Before further use of the appli-

ance, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its function. Check for alignment of moving

parts, binding of moving parts, breakage of parts, mount-

ing and any other condition that may effect its operation.

A guard or other part that is damaged should be properly

repaired or replaced by an authorized service center un-

less indicated elsewhere in this manual.

Keep hands and feet away from cutting area.

 Make sure all guards, straps, deflectors and handles are

properly and securely attached.

 Use only the manufacturer’s replacement string in the

cutting head when using a string trimmer attachment.

Do not use any other cutting attachment, for example,

metal wire, rope, or the like. To install any other brand of

4 — English

 Remove or disconnect battery before servicing, cleaning

or removing material from the gardening appliance.

 Use battery only with charger listed. For use with 40V

lithium-ion battery packs. See Tool/Appliance/Battery

Pack/Charger Correlation Supplement 988000-842.

 Do not dispose of the batteries in a fire. The cell may

explode. Check with local codes for possible special

disposal instructions.

 Do not open or mutilate the batteries. Released electrolyte

is corrosive and may cause damage to the eyes or skin.

It may be toxic if swallowed.

Do not place battery tools or their batteries near fire or

heat. This will reduce the risk of explosion and possibly

injury.

Batteries can explode in the presence of a source

of ignition, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product

in the presence of open flame. An exploded battery can

propel debris and chemicals. If exposed, flush with water

immediately.

 Do not crush, drop or damage battery pack. Do not

use a battery pack or charger that has been dropped or

received a sharp blow. A damaged battery is subject to

explosion. Properly dispose of a dropped or damaged

battery immediately.

 Exercise care in handling batteries in order not to short the

battery with conducting materials such as rings, bracelets,

and keys. The battery or conductor may overheat and

cause burns.

For best results, your battery tool should be charged in

a location where the temperature is more than 50°F but

less than 100°F. To reduce the risk of serious personal

injury, do not store outside or in vehicles.

Under extreme usage or temperature conditions,

battery leakage may occur. If liquid comes in contact

with your skin, wash immediately with soap and water,

then neutralize with lemon juice or vinegar. If liquid gets

into your eyes, flush them with clean water for at least

10 minutes, then seek immediate medical attention.

Following this rule will reduce the risk of serious personal

injury.

Save these instructions. Refer to them frequently and

use them to instruct others who may use this power tool.

If you loan someone this power tool, loan them these

instructions also.

cutting head to the string trimmer attachment can result

in serious personal injury.

Never operate unit without the grass deflector in place

and in good condition.

 Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string

head located over 30 in. or more above the ground.

Store idle appliances indoors - When not in use, power

head and attachments should be stored indoors in a dry,

locked place out of the reach of children.

Never use flailing devices, wire or rope on any attachment.

Inspect area to be cut. Remove objects (rocks, broken

glass, nails, wire, string, etc.) which can be thrown or

become entangled in cutting head.

Keep the air vents clean and free of debris to avoid

overheating the motor. Clean after each use.

Stop the unit and disconnect the power source when not

in use. Carry the unit with the motor stopped.

Store out of the reach of children.

Do not hang unit so that the switch trigger is depressed.

Battery tools do not have to be plugged into an electrical

outlet; therefore, they are always in operating condition.

Be aware of possible hazards when not using your battery

tool or when changing accessories. Following this rule will

reduce the risk of electric shock, fire, or serious personal

injury.

 Do not charge battery tool in rain, or damp or wet location.

Following this rule will reduce the risk of electric shock.

 Do not use battery-operated appliance in rain.

 Do not grasp the exposed cutting blades or cutting edges

when picking up or holding the appliance.

 Keep hands away from blades.

 Do not allow power head to be used as a toy. Close

attention is necessary when used by or near children.

 Do not handle charger, including charger plug, and

charger terminals with wet hands.

 Use extra care when cleaning on stairs.

 Do not use to pick up flammable or combustible liquids,

such as gasoline, or use in areas where they may be

present.

IMPORTANT SAFETY INSTRUCTIONS

ADDITIONAL SPECIFIC SAFETY RULES CAN BE FOUND IN THE

APPLICABLE ATTACHMENT’S OPERATOR’S MANUAL

5 — English

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s

Manual

To reduce the risk of injury, user must read and understand operator’s

manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Keep Bystanders

Away

Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury or property

damage.

No Blade

Do not install or use any type of blade on a product displaying this

symbol.

Recycle Symbol

This product uses lithium-ion (Li-ion) batteries. Local, state, or federal

laws may prohibit disposal of batteries in ordinary trash. Consult your

local waste authority for information regarding available recycling and/

or disposal options.

Direct Current Type or a characteristic of current

No Load Speed Rotational speed, at no load

.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

V Volts Voltage

Hz Hertz Frequency (cycles per second)

min Minutes Time

6 — English

FEATURES

KNOW YOUR POWER HEAD

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

ADJUSTABLE FRONT HANDLE

The front handle assembly can be adjusted for ease of

operation and to help prevent loss of control.

HANDLE OVERMOLD

Handle overmold provides added user comfort.

TRIGGER LOCK-OUT

The trigger lock-out prevents accidental starting.

VARIABLE SPEED SWITCH TRIGGER

This tool has a variable speed switch that delivers higher

speed with increased trigger pressure. Speed is controlled

by the amount of switch trigger depression.

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Power Head

Front Handle

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this product.

Any such alteration or modification is misuse and could

result in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always remove the battery pack from the

product when assembling parts.

7 — English

ASSEMBLY

The attachment connects to the power head by means of

a coupler device.

 Stop the motor and remove the battery pack.

 Loosen the knob on the coupler of the power head shaft

and remove the end cap from the attachment.

 Push in the button located on the attachment shaft. Align

the button with the guide recess on the power head coupler

and slide the two shafts together. Rotate the attachment

shaft until the button locks into the positioning hole.

NOTE: If the button does not release completely in the

positioning hole, the shafts are not locked into place.

Slightly rotate from side to side until the button is locked

into place.

 Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating

equipment; check it periodically for tightness during use

to avoid serious personal injury.

REMOVING THE ATTACHMENT FROM THE

POWER HEAD

 Stop the motor and remove the battery pack.

 Loosen the knob.

 Push in the button and twist the shafts to remove and

separate ends.

ATTACHING THE FRONT HANDLE

See Figure 3.

 Loosen and remove the wing bolt and washer from the

handle.

 Install the handle on the power head shaft in the area

indicated by the illustration.

 Adjust handle up or down, if necessary, to desired

operating position.

 Reinstall the washer and wing bolt. Tighten wing bolt to

secure.

INSTALLING AN ATTACHMENT TO THE POWER

HEAD

See Figure 2.

WARNING:

Read and understand entire Operator’s Manual for each

optional attachment used on this power head and follow

all warnings and instructions. Failure to follow all instruc-

tions could result in electric shock, fire and/or serious

personal injury.

WARNING:

This 40 V power head is designed to be used only with the

attachment models that are specified in this Operator’s

Manual. It is not designed to be used with brush cutters

or other attachment models. Use of other attachments

could cause serious personal injuries or property damage.

WARNING:

Never install, remove, or adjust any attachment while

power head is running. Failure to stop the motor can

cause serious personal injury. Never operate power head

without an attachment.

This 40 V power head may be used with only the following

Ryobi Expand-It attachments:

 RY15518 Edger

 RY15519 Blower

 RY15523 and RY15523A Straight Shaft String Trimmer

 RY15525 Curved Shaft String Trimmer

 RY15550 Cultivator

8 — English

OPERATION

WARNING:

Read and understand entire Operator’s Manual for

each optional attachment used on this power head and

follow all warnings and instructions. Failure to follow all

instructions could result in electric shock, fire and/or

serious personal injury.

WARNING:

Do not allow familiarity with products to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked

to comply with ANSI Z87.1. Hearing and/or head

protection may also be required depending on the type

of attachment used and as prescribed in the attachment’s

Operator’s Manual. Failure to do so could result in objects

being thrown into your eyes and other possible serious

injuries.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

This product will accept Ryobi 40 V lithium-ion battery

packs only.

For complete charging instructions, refer to the Operator’s

Manuals for your Ryobi battery pack and charger models.

WARNING:

Always remove battery pack from your tool when you are

assembling parts, making adjustments, cleaning, or when

not in use. Removing battery pack will prevent accidental

starting that could cause serious personal injury.

INSTALLING/REMOVING BATTERY PACK

See Figure 4.

To install battery pack:

 Place the battery pack in the power head. Align raised

ribs on battery pack with grooves in the power head’s

battery port.

WARNING:

Make sure the latch on the bottom of the battery pack

snaps in place and the battery pack is fully seated and

secure in the power head battery port before beginning

operation. Failure to securely seat the battery pack could

cause the battery pack to fall out, resulting in serious

personal injury.

To remove battery pack:

 Press and hold the battery latch button at the bottom of

the battery pack.

 Remove battery pack from the power head.

WARNING:

To avoid serious personal injury, always remove the

battery pack and keep hands clear of the trigger lock-out

when carrying or transporting the tool.

ADJUSTING THE FRONT HANDLE

See Figure 5.

The angle of the front handle can be adjusted 180°.

 Remove the battery pack.

 Set the power head on a flat surface and turn the knob

counterclockwise to loosen the handle.

 Adjust the handle as desired.

 Turn the knob clockwise until the handle is securely

tightened before reinstalling the battery pack.

STARTING/STOPPING THE POWER HEAD

See Figure 6.

To start:



Press and hold the trigger lock-out.



Depress the switch trigger.

To stop:



Release the switch trigger to stop the power head.



Upon release of the switch trigger, the trigger lock-out

will automatically reset to the locked position.

OPERATING THE POWER HEAD

See Figures 7 - 11.

Hold the power head with your right hand on the rear handle

and your left hand on the front handle. Keep a firm grip with

both hands while in operation. Power head should be held at

a comfortable position with the rear handle about hip height.

Always operate power head with switch trigger completely

depressed. If debris becomes wrapped around the

attachment, RELEASE THE SWITCH TRIGGER, remove the

battery pack, and remove the debris.

TRIGGER LOCK-OUT (GÂCHETTE AVEC VERROU,

GATILLO CON SEGURO)

9 — English

OPERATION

WARNING:

Extreme care must be taken when using a blade attach-

ment to ensure safe operation. Read the safety informa-

tion for safe operation when using a blade attachment

and refer to the safety rules and instructions in your at-

tachment manual. Never use a brush cutter attachment

with this power head. Improper operation of a blade or

any attachment could result in serious injury.

WARNING:

Always hold the power head away from the body keeping

clearance between the body and the tool. Any contact

with an attachment cutting head can result in burns and/

or other serious personal injury.

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts can create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Head protection may also be required depending on

the type of attachment used and as prescribed in the

attachment’s Operator’s Manual. Failure to do so could

result in objects being thrown into your eyes and other

possible serious injuries.

WARNING:

To avoid serious personal injury, always remove the bat-

tery pack from the tool when cleaning or performing any

maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which can result in serious personal injury.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an Authorized Service Center.

CLEANING THE POWER HEAD

 Stop the motor and remove the battery pack.

 Clean dirt and debris from the power head using a damp

cloth with a mild detergent.

NOTICE:

Do not use any strong detergents on the plastic housing or

the handle. They can be damaged by certain aromatic oils

such as pine and lemon, and by solvents such as kerosene.

STORING THE POWER HEAD

 Remove the battery pack from the power head before

storing.

 Clean all foreign material from the power head.

 Store it in a place that is inaccessible to children.

 Keep away from corrosive agents such as garden chemi-

cals and de-icing salts.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Motor fails to start when switch

trigger is depressed

Battery is not secure.

Battery is not charged.

To secure the battery pack, make sure the latch on the

bottom of the battery pack is snapped into place.

Charge the battery pack according to the instructions

included with your model.

TRIGGER LOCK-OUT (GÂCHETTE AVEC VERROU,

GATILLO CON SEGURO)

10 — English

LIMITED WARRANTY STATEMENT

Techtronic Industries North America, Inc., warrants to the

original retail purchaser that this RYOBI® brand outdoor

product is free from defect in material and workmanship

and agrees to repair or replace, at Techtronic Industries

North America, Inc.’s, discretion, any defective product

free of charge within these time periods from the date of

purchase.

 Three years if the product is used for personal, family

or household use;

 90 days, if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser only

and commences on the date of the original retail purchase.

Any part of this product found in the reasonable judgment

of Techtronic Industries North America, Inc. to be defective

in material or workmanship will be repaired or replaced

without charge for parts and labor by an authorized service

center for RYOBI® brand outdoor products (Authorized

Ryobi Service Center).

The product, including any defective part, must be returned

to an authorized Ryobi service center within the warranty

period. The expense of delivering the product to the service

center for warranty work and the expense of returning it

back to the owner after repair or replacement will be paid

by the owner. Techtronic Industries North America, Inc.’s,

responsibility in respect to claims is limited to making the

required repairs or replacements and no claim of breach of

warranty shall be cause for cancellation or rescission of the

contract of sale of any RYOBI® brand outdoor product. Proof

of purchase will be required by the dealer to substantiate

any warranty claim. All warranty work must be performed

by an authorized service dealer.

This warranty is limited to ninety (90) days from the date

of original retail purchase for any RYOBI® brand outdoor

product that is used for rental or commercial purposes, or

any other income-producing purpose.

This warranty does not cover any product that has been

subject to misuse, neglect, negligence, or accident, or that

has been operated in any way contrary to the operating

instructions as specified in this operator’s manual. This

warranty does not apply to any damage to the product that

is the result of improper maintenance or to any product

that has been altered or modified. The warranty does not

extend to repairs made necessary by normal wear or by the

use of parts or accessories which are either incompatible

with the RYOBI® brand outdoor product or adversely affect

its operation, performance, or durability. In addition, this

warranty does not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive

Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,

Blower Fans, Blower and Vacuum Tubes, Vacuum Bag

and Straps, Guide Bars, Saw Chains

Techtronic Industries North America, Inc., reserves the

right to change or improve the design of any RYOBI® brand

outdoor product without assuming any obligation to modify

any product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED

IN THEIR ENTIRETY AFTER THE EXPIRATION OF

THE APPROPRIATE THREE-YEAR OR NINETY-DAY

WARRANTY PERIOD. TECHTRONIC INDUSTRIES

NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS

WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO

THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS

AND TECHTRONIC INDUSTRIES NORTH AMERICA,

INC., DOES NOT ASSUME OR AUTHORIZE ANYONE

TO ASSUME FOR THEM ANY OTHER OBLIGATION.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE

LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC

INDUSTRIES NORTH AMERICA, INC., ASSUMES NO

RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,

OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED

TO, EXPENSE OF RETURNING THE PRODUCT TO AN

AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE

OF DELIVERING IT BACK TO THE OWNER, MECHANIC’S

TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,

RENTAL OF A LIKE PRODUCT DURING THE TIME

WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,

LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS

OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS

OF TIME, OR INCONVENIENCE. SOME STATES DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all RYOBI® brand outdoor products

manufactured by or for Techtronic Industries North America,

Inc., and sold in the United States and Canada.

To locate your nearest Authorized Ryobi Service Center,

dial 1-800-860-4050.

WARRANTY

990000720

11-20-13 (REV:02)

TECHTRONIC INDUSTRIES NORTH AMERICA, INC.

1428 Pearman Dairy Road, Anderson, SC 29625 USA

1-800-860-4050 • www.ryobitools.com

A subsidiary of Techtronic Industries Co., Ltd. • OTC: TTNDY

• PARTS AND SERVICE

Prior to requesting service or purchasing replacement parts, please obtain your model

and serial number from the product data plate.

• MODEL NO. ______________________SERIAL NO. __________________________

• HOW TO OBTAIN REPLACEMENT PARTS:

Replacement parts can be purchased online at www.ryobitools.com or by calling

1-800-860-4050. Replacement parts can also be obtained at one of our Authorized

Service Centers.

• HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:

Authorized Service Centers can be located online at www.ryobitools.com or by

calling 1-800-860-4050.

• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:

To obtain Customer or Technical Support please contact us at 1-800-860-4050.

• PIÈCES ET SERVICE

Avant de faire la demande de service ou l’achat de pièces de remplacement, veuillez

obtenir le numéro de série du modèle à partir de la plaque de données du produit.

• NUMÉRO DE MODÈLE ____________NUMÉRO DE SÉRIE ___________________

• COMMENT OBTENIR LES PIÈCES DE REMPLACEMENT :

Les pièces de remplacement peuvent être achetées en ligne sur le site

www.ryobitools.com ou par téléphone au 1-800-860-4050. Les pièces de remplacement

peuvent être obtenues à un de nos centres de service autorisés.

• COMMENT TROUVER UN CENTRE DE SERVICE AUTORISÉ :

Les centres de service autorisés peuvent être localisés en ligne au www.ryobitools.

com ou en téléphonant au 1-800-860-4050.

• COMMENT OBTENIR DE L’AIDE EN CONTACTANT LE SERVICE À LA CLIENTÈLE :

Pour contacter le service à la clientèle pour une question technique ou pour tout autre

renseignement, veuillez nous téléphoner au 1-800-860-4050.

• PIEZAS DE REPUESTO Y SERVICIO

Antes de solicitar servicio técnico o comprar piezas de repuesto, obtenga su modelo

y número de serie de la placa de datos del producto.

• NÚMERO DE MODELO ____________NÚMERO DE SERIE ___________________

• CÓMO OBTENER PIEZAS DE REPUESTO:

Las piezas de repuesto se pueden comprar en nuestro sitio en la red mundial, en la

dirección www.ryobitools.com o llamando al 1-800-860-4050. Las piezas de repuesto

también se pueden obtener en uno de nuestros Centros de Servicio Autorizados.

• CÓMO LOCALIZAR UN CENTRO DE SERVICIO AUTORIZADO:

Puede encontrar los Centros de Servicio Autorizados visitando nuestro sitio en la red

mundial, en la dirección www.ryobitools.com or by calling 1-800-860-4050.

• CÓMO OBTENER SERVICIO O ASISTENCIA TÉCNICA AL CONSUMIDOR:

Para obtener Servicio o Asistencia Técnica al Consumidor, sírvase comunicarse con

nosotros llamando al 1-800-860-4050.

CALIFORNIA PROPOSITION 65

WARNING:

This product and substances that may

become airborne from its use may con-

tain chemicals, including lead, known to

the State of California to cause cancer,

birth defects, or other reproductive harm.

Wash hands after handling.

RYOBI is a registered trademark of Ryobi Limited

and is used pursuant to a license granted by

Ryobi Limited.

RYOBI est une marque déposée de Ryobi Limited

et est utilisée en vertu d’une licence accordée

par Ryobi Limited.

RYOBI es una marca registrada de Ryobi Limited

y se utiliza conforme a una licencia otorgada por

Ryobi Limited.

PROPOSITION 65 DE L’ÉTAT DE

CALIFORNIE

AVERTISSEMENT :

Ce produit ainsi que les substances

rejetées dans l’air à la suite de son

utilisation peuvent contenir des produits

chimiques, notamment du plomb qui,

selon l’État de la Californie, peuvent

causer le cancer, des anomalies

congénitales et d’autres dommages au

système reproducteur. Bien se laver

les mains après toute manipulation.

CALIFORNIA - PROPUESTA DE

LEY NÚM. 65

ADVERTENCIA:

Este producto y sustancias que puedan

llegar a ser aerotransportadas por su uso

pueden contener sustancias químicas

(por ejemplo, plomo) consideradas por

el estado de California como causantes

de cáncer, defectos de nacimiento

u otras alteraciones reproductivas.

Lávese las manos después de utilizar

el aparato.

OPERATOR’S MANUAL

MANUEL D’UTILISATION / MANUAL DEL OPERADOR

40 VOLT POWER HEAD

40V BLOC MOTEUR / 40V CABEZAL MOTOR

RY40002

ALL VERSIONS / TOUTES LES VERSIONS / TODAS LAS VERSIONES

Your blower attachment has been engineered and manufactured to our high standard for dependability, ease of operation,

and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

L’accessoire soufflante a été conçue et fabriquée

conformément à nos strictes normes de fiabilité, simplicité

d’emploi et sécurité d’utilisation. Correctement entretenue,

elle vous donnera des années de fonctionnement robuste

et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

Su nuevo accesorio de soplador ha sido diseñada y

fabricada de conformidad con las estrictas normas para

brindar fiabilidad, facilidad de uso y seguridad para el

operador. Con el debido cuidado, le brindará muchos años

de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador

antes de usar este producto.

Le agradecemos su compra.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

JET FAN BLOWER ATTACHMENT

ACCESSOIRE SOUFFLEUR À AIR PULSÉ

ACCESORIO DE SOPLADOR CON

VENTILADOR DE CHORRO

RYAXA22

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées dans le manuel

d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el

manual del operador.

iii

Fig. 1

A - Hanger cap (capuchon de suspension, tapa de brazo de suspensión)

B - Blower attachment shaft (arbre de l’accessoire soufflante, eje del

accesorio de soplador)

Fig. 3 Fig. 4Fig. 2

A - Power head shaft (arbre moteur , cabezal

motor eje)

B - Coupler (coupleur, acoplador)

C - Guide recess (logement guide, hueco guía)

D - Button (bouton, botón)

E - Attachment shaft (arbre de l’accessoire, eje

del accesorio)

F - Positioning hole (trou de positionnement,

orificio de posicionamiento)

G - Knob (bouton, perilla)

C - Air inlet (entrée d’air, entrada de aire)

D - Blower housing (boîtier de la soufflante, caja del soplador)

E - Air outlet (sortie d’air, salida de aire)

A - Hanger cap (capuchon de suspension, tapa

de suspensión)

B - Hole (trou, orificio)

C - Secondary hole (trou secondaire, orificio

secundario)

D - Button (bouton, botón)

 Introduction ...................................................................................................................................................................... 2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................3-4

Instructions importantes concernant la sécurité / Instrucciones de seguridad importantes

 Specific Safety Rules ........................................................................................................................................................ 4

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ............................................................................................................................................................................ 5

Symboles / Símbolos

 Features ............................................................................................................................................................................ 6

Caractéristiques / Características

 Assembly .......................................................................................................................................................................6-7

Assemblage / Armado

 Operation .......................................................................................................................................................................7-8

Utilisation / Funcionamiento

 Maintenance ..................................................................................................................................................................... 8

Entretien / Mantenimiento

 Warranty ........................................................................................................................................................................... 9

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio .......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

3 — English

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock,

fire, and/or serious personal injury.

SAVE THESE INSTRUCTIONS

 Read these instructions and the instructions for the power

head thoroughly before using the attachment.

 Know the tool. Read and understand the operator’s

manual and observe the warnings and instruction labels

affixed to the tool.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine of a gas power head

in a confined space, building, near open windows, or

in other unventilated space where dangerous carbon

monoxide fumes can collect. Carbon monoxide, a color-

less, odorless, and extremely dangerous gas, can cause

unconsciousness or death.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection

when operating this unit. Failure to do so could result in

objects being thrown into your eyes and other possible

serious injuries.

 Wear heavy long pants, boots, and gloves. Do not wear

loose fitting clothing, short pants, jewelry of any kind,

sandals, or go barefoot.

 To reduce the risk of injury associated with objects be-

ing drawn into rotating parts, do not wear loose clothing,

scarves, neck chains, and the like.

 Secure long hair so it is above shoulder level to prevent

entanglement in any moving parts.

 Keep all bystanders, children, and pets at least 50 ft.

away.

 Stay alert, watch what you are doing, and use common

sense when operating a power tool. Do not use tool while

tired, ill, upset, or under the influence of drugs, alcohol,

or medication. A moment of inattention while operating

power tools may result in serious personal injury.

 Do not operate in poor lighting.

 Do not overreach. Keep proper footing and balance at all

times. Proper footing and balance enables better control

of the tool in unexpected situations.

 Keep all parts of your body away from any moving part.

 Inspect unit before each use for loose fasteners and

damaged or missing parts. Correct before using the at-

tachment. Failure to do so can cause serious injury.

 Use only recommended or equivalent manufacturer’s

replacement parts and accessories. Use of any other

parts may create a hazard or cause product damage.

IMPORTANT SAFETY INSTRUCTIONS

 Do not, under any circumstance, use any attachment or

accessory on this product, which was not provided with

the product, or identified as appropriate for use with this

product in the operator’s manual.

 Avoid dangerous environments. Do not use the attach-

ment in damp or wet locations. Do not use in rain.

 Use the right attachment. Do not use attachment for any

job except that for which it is intended.

 Do not touch areas around the muffler or cylinder of a gas

power head. These parts get hot from operation. Contact

with hot surfaces could result in possible serious personal

injury.

 Always stop the engine or motor and remove the spark

plug wire or disconnect from the power supply before

making any adjustments or repairs.

 Keep firm footing and balance. Do not overreach. Over-

reaching can result in loss of balance or exposure to hot

surfaces.

 Maintain the unit per maintenance instructions in this

Operator’s Manual.

 Do not use on a ladder, rooftop, tree, or other unstable

support. Stable footing on a solid surface enables better

control of the blower in unexpected situations.

 Before cleaning, repairing, or inspecting, shut off the

engine or motor and make certain all moving parts have

stopped. Disconnect the spark plug wire and keep the

wire away from the plug to prevent starting or disconnect

from the power supply.

 We recommend taking your equipment to a qualified

service center for repair, as service performed by in-

experienced or unqualified persons may damage the

equipment, create unsafe conditions, injury to user and/

or void your warranty.

WHEN USING AN ELECTRIC POWER HEAD:

 Do not leave appliance when plugged in. Unplug from

outlet when not in use and before servicing.

 Do not allow to be used as a toy. Close attention is nec-

essary when used by or near children.

 Use only as described in this manual. Use only manufac-

turer’s recommended attachments.

 Do not use with damaged cord or plug. If appliance is

not working as it should, has been dropped, damaged,

left outdoors, or dropped into water, return it to a service

center.

 Do not pull or carry by cord, use cord as a handle, close a

door on cord, or pull cord around sharp edges or corners.

Do not run appliance over cord. Keep cord away from

heated surfaces.

 Do not unplug by pulling on cord. To unplug, grasp the

plug, not the cord.

 Do not handle plug or appliance with wet hands.

4 — English

 Wear a face filter mask in dusty conditions to reduce the

risk of injury associated with the inhalation of dust.

 Check the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which

can be thrown or become entangled in the machine.

 To reduce the risk of injury associated with contacting ro-

tating parts, stop the engine before installing or removing

attachments. Do not operate without all guard(s), hous-

ings, and air outlet in place. Always disconnect the spark

plug or disconnect from power source before performing

maintenance or accessing any movable parts.

 To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

 Never direct air outlet towards any persons, animals,

plants, or delicate objects.

 Keep air inlet clear of debris.

 Always stay clear of air inlet while blower is running.

 Do not point blower in direction of people or pets.

 Never place blower attachment on any surface, except

a hard, clean surface when engine or motor is running.

SPECIFIC SAFETY RULES

Gravel, sand, and other debris can be picked up by the

air inlet and thrown at the operator or bystanders, causing

possible serious injuries.

 Never use for spreading chemicals, fertilizers, toxic sub-

stances, or any other hazardous chemicals.

 Never use blower attachment near fires, fireplaces,

hot ashes, barbecue pits, etc., which may cause fire to

spread.

 For household use only.

 Store Idle Appliance Indoors — When not in use, product

should be stored indoors in a dry and high or locked up

place—out of the reach of children.

 Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you

loan someone this product, loan them these instructions

also to prevent misuse of the product and possible injury.

NOTE: SEE YOUR POWER HEAD OPERATOR’S MANUAL

FOR ADDITIONAL SPECIFIC SAFETY RULES.

SAVE THESE INSTRUCTIONS

 Do not put any object into openings. Do not use with any

opening blocked; keep free of dust, lint, hair, and anything

that may reduce air flow.

 Keep hair, loose clothing, fingers, and all parts of body

away from openings and moving parts.

 Turn off all controls before unplugging.

IMPORTANT SAFETY INSTRUCTIONS

5 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME EXPLANATION

Safety Alert Symbol Precautions that involve your safety.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 as well as hearing protection when

operating this equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Long Hair Risk of long hair being drawn into air inlet.

Loose Clothing Risk of loose clothing being drawn into air inlet.

Ricochet

Thrown objects can ricochet and result in personal injury or

property damage.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

La page charge ...

Ryobi RY40255-BLW Mode d'emploi

Marque: Ryobi

Modèle: RY40255-BLW

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RY40255-BLW User guide

Ryobi RY40255-BLW Mode d'emploi

Ryobi RY40255-BLW Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents