ProScan PLCD3271A-D Manuel utilisateur

Marque: ProScan

Modèle: PLCD3271A-D

Catégorie: Téléviseurs LCD

Taper: Manuel utilisateur

Model:PLCD3271A-D

Contents

Caution

Safety Information

Unit and Accessories

Introduction

1. Front View

2. Rear View

4. Remote Control

Basic Operation

OSD Menu

1. Picture menu

2. Sound menu

3. Channel menu

4. Parental Control menu

5. Setup menu

6. Others menu

Simple Troubleshooting

5-9

8-9

11-18

11-12

15-16

3. Instruction for Wall Mount 7

Contents

Caution

Safety Information

Unit and Accessories

TV set

User's manual

Remote control

Batteries: 2xAAA

Instructions for fixing stand

Instructions for

fixing stand

Warranty Card

User's manual

Introduction

(IR) Infrared Receiver: Receives Infrared signals from the remote control.

1).(Power on/Standby)LED Indicator: Press POWER button to turn on or off.

Indicator off(Red) Standby mode

Indicator on(Blue) Power on mode

2). The functions of the buttons:

INPUT: Press to display the input source menu.

MENU: Press to display the OSD menu,

press again to exit the menu.

Press to scan through channels.

VOL+/-: Press to adjust the sound volume.

POWER: Turn on/standby the TV set.

The effective receiving range for the signal is 5-8 metres from the front of the remote

control window, and 30

to the left or right side and 20

above or below the remote control

window.

Press INPUT button on the TV set or SOURCE button on

the remote control to display the input source menu, and

use button on the TV set or

button on

remote control to select the input source, press OK button

on the remote control to enter.

Note: Before you select the input source, make sure the

connections are prepared.

Power Indicator

Remote Control window

(Keep clear)

1 Front View

Introduction

2. Rear View

Introduction

3. Instruction for Wall Mount

- Do not mount your PROSCAN TV at more than a 15 degree tilt.

- Always use two people to mount the TV to a wall.

- Do not install your Wall Mount Kit while your TV is turned on. It may result in

personal injury due to electric shock.

The wall mount kit (not included) with your purchase allows you to mount your

PROSCAN TV on the wall. For detailed information on installing the wall mount, refer

to the instructions provided by the wall mount manufacturer. It is strongly

recommended to contact a technician for professional assistance for wall mount

installation. PROSCAN is not responsible for any damage to the product or injury to

yourself or others resulting from the wall-mounting.

- 4 pcs of type M5x12 screws are required for installing the wall mount bracket to

your PROSCAN TV. Do not use screws that are longer than 12 mm. Screws that

are too long may cause damage to the inside of the TV set.

- Do not fasten the screws too tight for this may damage the TV or cause the

TV to fall, resulting in personal injury. PROSCAN is not liable for these kinds of

incidents

Dimensions for Mounting Hole Pattern

This PROSCAN TV is compatible with a 200mm x 200mm mounting hole pattern.

Introduction

4. Remote Control

The remote control is using Infra-Red(IR). Point it towards the front of the LCD TV. The remote

control may not work correctly if it is operated out of range or out of angle.

/ Vol-

Introduction

Installing Batteries

1. Open the battery compartment cover on the back of the remote control.

2. Insert two 1.5V AAA size batteries observing the polarity markings inside the battery

compartment. Don’t mix different types or used batteries with new ones.

3. Close the cover.

- The remote control should be operated within 23 feet(7m) and 30

to the left and right of the

IR Receiver on the front of the TV.

- Used batteries should be disposed properly.

Power on/off

1. Connect to the power supply with the power cord.

2. -To turn on the TV

Press POWER button on the TV or remote control.

-To turn off the TV

Press POWER button on the TV or remote control.

Input Source select

Press INPUT button on the TV set or SOURCE button on the remote

OK button on the remote control to enter.

Note: Before you select the input source, make sure the

connections are prepared.

Basic OSD Menu operation

Use button to select the main menu, and press OK button to enter the submenu.

Use button to select.

button to select the function item, press button to

or press button to enter the submenu.

* (Press MENU button to return to the upper menu.)

* (Press EXIT button to exit the menu display.)

Note1: Only when you input the suitable signal, the relevant items can be activated.

Note2: Please operating the OSD menu according to hint on the bottom of the banner.

Main menu

Picture

Sound

Channel

Parental

Setup

Others

Submenu

(Picture menu

for example)

Hint---you should operate the OSD menu according to the hint.

Press MENU button to display the OSD menu as below:

Basic Operation

Press OK button

control to display input source menu, and use CH+/- button on the TV set

button on remote control to select the input source, press

OSD Menu

1. Picture menu

Description

Picture mode: Select between Dynamic, Standard,

Movie, User and Power Saving.

You may select the picture mode directly by pressing

the P.MODE button on the remote control.

Picture Settings: Press button to enter the Picture Settings menu.

Screen Size: Select the displaying mode of the picture between Wide, Cinema, Zoom, Normal.

PC Settings: If the video input signal comes from your PC, you may adjust the Vertical Position,

Horizontal Position, Clock, Phase or even perform an Auto adjustment.

Contrast: Control the difference between the bright and

dark regions of the screen picture.

Brightness: Adjust brightness of the picture.

Color: Adjust color of the picture.

Tint: Control the fresh tones to make them appear natural.

Sharpness: Set the amount of fine detail in the picture.

Color Temp.: Select between Normal, Cool and Warm.

Note: when select the "Power Saving", the

machine is in energy-saving status(4.1).

OSD Menu

Auto Adjust: Press OK button to setup the parameter of

the screen automatically.

Clock: Adjust the pixel clock frequency, until the image

size is maximized for the screen.

H/V Position: Adjust the horizontal/vertical position of

the screen.

Phase: Adjust the phase of the ADC sampling clock

relative to the sync signal, until a stable image is obtained.

Reset: Press OK button to reset the settings.

OSD Menu

Dynamic Contrast: Select the dynamic contrast mode

between Off, Low, Medium and High.

Film Mode: Activate or deactivate the Film Mode.

Noise Reduction: If the broadcast signal received is

weak, you can select the DNR option to reduce the video

noise level between Off, Low, Medium and High.

MPEG Noise Reduction: Select the MPEG Noise

Reduction option to reduce the picture noise level

between Off, Low, Medium and High.

Advanced Picture Settings: Press button to enter the Advanced Picture Settings.

OSD Menu

2. Sound menu

Description

Sound Mode: Select your desired picture mode as

follow: Dynamic, Standard, Soft and User.

You may select the sound mode directly by pressing

the S.MODE button on the remote control.

Bass: Low frequency intensity.

Treble: High frequency intensity.

Balance: Left and right stereo audio channels balance.

Surround Mode: Enable or disenable the Surround function.

OSD Menu

Sound Settings: Press button to enter the Sound Settings menu.

AVL: Enable or disenable the Auto Volume Limited function.

Analog Sound: Select the Analog Sound mode between Stereo, Mono and SAP.

Digital Sound: Select the Digital Sound laguage.

Digital Audio Output: Select the Digital Audio Output mode between PCM, RAW and off.

Equalizer Settings: Press button to enter the Equalizer Settings menu.

Use / button to select the mode between User, Off,

Rock, Pop and Jazz.

adjust the equalizer bu yourself when you select

the User mode.

to adjust. You could come back to the Mode selecting

item by pressing button.

OSD Menu

Description

3. Channel menu

Channel List: Display the channel list.

Favorite List: Display the favorite channel list.

Channel Settings: Press button to display the Channel Settings menu.

Signal Type: Allow you to select antenna between Air and Cable.

Auto Channel Search: Press OK button to start auto channel search.

Press button to select the item, and press OK button

to change the setting.

OSD Menu

If you select “Cable” as input signal in Antenna item, you

can press OK button to search the channels automatically.

The receivable channels will be stored automatically.

When searching channels, press MENU to stop.

If you select “Air” as input signal in Antenna item, you

can press OK button to search the channels automatically.

The receivable channels will be stored automatically.

When searching channels, press MENU to stop.

NOTE: It will take a while to auto scan in NTSC or ATSC

mode, please wait patiently.

OSD Menu

4. Parental Control menu

OSD Menu

Description

V-CHIP: Press button to enter the V-CHIP menu.

You must enter the password to gain access to the Parental Control menu. The default password

is 0000. You may modify the following options:

TV Rating:

rating and press OK button to block or unblock rating.

Movie Rating: The Movie rating (MPAA) is used for

original movies rated by the Motion Picture Association

of America (MPAA) as broadcasted on cable TV and

not edited for television.

or X.

PG:

suited for younger viewers.

PG-13: Contains content that may not be appropriate for viewers

without parent.

NC-17:

X: Adults only.

US V-CHIP:

Change Password

Keypad Lock

OSD Menu

English Rating: Select among: C, C8+, G, PG,

14+ and 18+.

French Rating: Select among: G, 8ans+,

13ans+, 16ans+ and 18ans+.

Canada V-CHIP: Press button to enter the Canada

V-CHIP menu.

Block UnRated Show: Activate or deactivate the Block UnRated Show function.

Downloadable Rating: Setting the Downloadable Rating in DTV mode when the program

has the rating information.

Clear Downloadable Date: Clear the downloadable data of the TV.

Change password: Change the password, you must enter

the new password twice to confirm it.

Keypad Lock: Invalidate the buttons one the TV set.

Source Lock: Invalidate the source input you select.

Note: Do not forget the password.

Note:The two operations above only valid when playing the downloadable data stream.

OSD Menu

Description

5. Setup menu

OSD Menu

Closed Caption: Press button to enter the Closed Caption menu.

Caption Display: Activate or deactivate the Caption

Analog Caption Type: Allow you to select the basic

selection among: CC1, CC2, CC3, CC4, Text1, Text2,

Digital Caption Type: Allow you to select the advanced

selection among: Service1, Service2, Service3 Service4,

Digital CC Preset: Select the Digital CC Preset between

Digital CC Style: Setting the Digital CC Style.

Menu Language: Select OSD menu language.

Clock: Press button to enter the Clock menu.

Text3 and Text4.

Service 5 and Service 6.

Time zone: Select the time zone for the TV.

Auto Clock: Enable or disenable the Auto Clock

Setup Time: Display the setup time of the TV.

Day of Week: Display the day of week.

Daylight Saving Time: Enable or disenable the

Daylight Saving Time function for the TV.

function.

displaying.

Default and Custom.

OSD Menu

6. Others menu

OSD Menu

Description

Blue Screen: Turn on/off the blue screen function when there’s no signal.

No Signal Power Off: The TV will turn off automatically if there’s no signal after 10 minutes.

No Operation Power Off: The TV will turn off automatically if there’s no operation on the TV

All Reset: Reset all the settings.

after 3 hours.

Audio Only

Audio Only: Turn off the screen when playing radio programs. Press the power button for 3

seconds to turn on the screen.

La page charge ...

ProScan PLCD3271A-D Manuel utilisateur

Marque: ProScan

Modèle: PLCD3271A-D

Catégorie: Téléviseurs LCD

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: ProScan PLCD3271A-D User manual

Documents connexes

ProScan PLDV321300-E Manuel utilisateur

ProScan PLCD3271A-D Manuel utilisateur

ProScan PLCD3271A-D Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents