Bosch Power Tools 1617EVSPK Manuel utilisateur

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1617

1617EVS

1617PK

1617EVSPK

1618

1618EVS

0 601 617 061

For English

Parlez-vous français?

¿Habla español?

See page 2 Voir page 23 Ver página 44

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Call Toll Free

for Consumer Information

& Service Locations

Pour renseignement des

consommateurs et centres

de service, appelez au

numéro gratuit :

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

2

1

0

IN

50

40

30

20

10

0

MM

BM 2610908996 6-04 6/21/04 4:47 PM Page 1

Read and understand all instructions. Failure to follow all instructions

listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

-2-

Work Area

Keep your work area clean and well lit.

Cluttered benches and dark areas invite

accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust.

Power

tools create sparks which may ignite the dust

or fumes.

Keep by-standers, children, and visitors

away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with

a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized

outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified

electrician to install a polarized outlet. Do

not change the plug in any way. Double

Insulation xxxx eliminates the need for the

three wire grounded power cord and

grounded power supply system.

Before

plugging in the tool, be certain the outlet

voltage supplied is within the voltage marked

on the nameplate. Do not use “AC only”

rated tools with a DC power supply.

Avoid body contact with grounded

surfaces such as pipes, radiators, ranges

and refrigerators.

There is an increased risk

of electric shock if your body is grounded. If

operating the power tool in damp locations is

unavoidable, a Ground Fault Circuit

Interrupter must be used to supply the power

to your tool. Electrician’s rubber gloves and

footwear will further enhance your personal

safety.

Don't expose power tools to rain or wet

conditions.

Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the

cord to carry the tools or pull the plug

from an outlet. Keep cord away from heat,

oil, sharp edges or moving parts. Replace

damaged cords immediately.

Damaged

cords increase the risk of electric shock.

When operating a power tool outside, use

an outdoor extension cord marked "W-A"

or "W."

These cords are rated for outdoor

use and reduce the risk of electric shock.

Refer to “Recommended sizes of Extension

Cords” in the Accessory section of this

manual.

Personal Safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use tool while tired or

under the influence of drugs, alcohol, or

medication.

A moment of inattention while

operating power tools may result in serious

personal injury.

Dress properly. Do not wear loose

clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away

from moving parts.

Loose clothes, jewelry,

or long hair can be caught in moving parts.

Keep handles dry, clean and free from oil

and grease.

Avoid accidental starting. Be sure switch

is “OFF” before plugging in.

Carrying tools

with your finger on the switch or plugging in

tools that have the switch “ON” invites

accidents.

Remove adjusting keys or wrenches

before turning the tool “ON”.

A wrench or

a key that is left attached to a rotating part of

the tool may result in personal injury.

Do not overreach. Keep proper footing

and balance at all times.

Proper footing and

balance enables better control of the tool in

unexpected situations.

Use safety equipment. Always wear eye

protection.

Dust mask, non-skid safety

shoes, hard hat, or hearing protection must

be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to

secure and support the workpiece to a

stable platform.

Holding the work by hand

or against your body is unstable and may

lead to loss of

control.

!

WARNING

Power Tool Safety Rules

BM 2610908996 6-04 6/21/04 4:47 PM Page 2

-3-

Safety Rules for Routers

Do not force tool. Use the correct tool for

your application.

The correct tool will do the

job better and safer at the rate for which it is

designed.

Do not use tool if switch does not turn it

“ON” or “OFF”.

Any tool that cannot be

controlled with the switch is dangerous and

must be repaired.

Disconnect the plug from the power

source before making any adjustments,

changing accessories, or storing the tool.

Such preventive safety measures reduce the

risk of starting the tool accidentally.

Store idle tools out of reach of children

and other untrained persons.

Tools are

dangerous in the hands of untrained users.

Maintain tools with care. Keep cutting

tools sharp and clean.

Properly maintained

tools, with sharp cutting edges are less likely

to bind and are easier to control. Any

alteration or modification is a misuse and

may result in a dangerous condition.

Check for misalignment or binding of

moving parts, breakage of parts, and any

other condition that may affect the tools

operation. If damaged, have the tool

serviced before using.

Many accidents are

caused by poorly maintained tools. Develop

a periodic maintenance schedule for your

tool.

Use only accessories that are

recommended by the manufacturer for

your model.

Accessories that may be

suitable for one tool, may become hazardous

when used on another tool.

Service

Tool service must be performed only by

qualified repair personnel.

Service or

maintenance performed by unqualified

personnel could result in a risk of injury. For

example: internal wires may be misplaced or

pinched, safety guard return springs may be

improperly mounted.

When servicing a tool, use only identical

replacement parts. Follow instructions in

the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk

of electric shock or injury. Certain cleaning

agents such as gasoline, carbon

tetrachloride, ammonia, etc. may damage

plastic parts.

Hold tool by insulated gripping surfaces

when performing an operation where the

cutting tool may contact hidden wiring or

its own cord.

Contact with a "live" wire will

make exposed metal parts of the tool "live"

and shock the operator.

If cutting into

existing walls or other blind areas where

electrical wiring may exist is unavoidable,

disconnect all fuses or circuit breakers

feeding this worksite.

Always make sure the work surface is

free from nails and other foreign objects.

Cutting into a nail can cause the bit and the

tool to jump and damage the bit.

Never hold the workpiece in one hand and

the tool in the other hand when in use.

Never place hands near or below cutting

surface.

Clamping the material and guiding

the tool with both hands is safer.

Never lay workpiece on top of hard

surfaces, like concrete, stone, etc...

Protruding cutting bit may cause tool to jump.

Always wear safety goggles and dust

mask. Use only in well ventilated area.

Using personal safety devices and working in

safe environment reduces risk of injury.

After changing the bits or making any

adjustments, make sure the collet nut and

any other adjustment devices are

securely tightened.

Loose adjustment

device can unexpectedly shift, causing loss

of control, loose rotating components will be

violently thrown.

Never start the tool when the bit is

engaged in the material.

The bit cutting

edge may grab the material causing loss of

control of the cutter.

Always hold the tool with two hands

during start-up

. The reaction torque of the

motor can cause the tool to twist.

The direction of feeding the bit into the

material is very important and it relates to

the direction of bit rotation. When viewing

BM 2610908996 6-04 6/21/04 4:47 PM Page 3

the tool from the top, the bit rotates

clockwise. Feed direction of cutting must

be counter-clockwise.

NOTE: inside and

outside cuts will require different feed

direction, refer to section on feeding the

router. Feeding the tool in the wrong

direction, causes the cutting edge of the bit

to climb out of the work and pull the tool in

the direction of this feed.

Never use dull or damaged bits. Sharp

bits must be handled with care.

Damaged

bits can snap during use. Dull bits require

more force to push the tool, possibly causing

the bit to break.

Never touch the bit during or immediately

after the use.

After use the bit is too hot to

be touched by bare hands.

Never lay the tool down until the motor

has come to a complete standstill.

The

spinning bit can grab the surface and pull the

tool out of your control.

Never use bits that have a cutting

diameter greater than the opening in the

base.

Some dust created by

power sanding, sawing,

grinding, drilling, and other construction

activities contains chemicals known to

cause cancer, birth defects or other

reproductive harm. Some examples of

these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement

and other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such

as those dust masks that are specially

designed to filter out microscopic particles.

-4-

!

WARNING

BM 2610908996 6-04 6/21/04 4:47 PM Page 4

-5-

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

.../min Revolutions or reciprocation per minute Revolutions, strokes, surface speed,

orbits etc. per minute

0 Off position Zero speed, zero torque...

1, 2, 3, ... Selector settings Speed, torque or position settings.

I, II, III, Higher number means greater speed

Infinitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction Designates Double Insulated

Construction tools.

Earthing terminal Grounding terminal

Warning symbol Alerts user to warning messages

Ni-Cad RBRC seal Designates Ni-Cad battery recycling

program

Symbols

A

0

A

0

A

0

A

0

A

This symbol designates

that this tool is listed by

Underwriters Laboratories.

This symbol designates

that this tool is listed by

the Canadian Standards

Association.

This symbol designates

that this tool is listed to

Canadian Standards by

Underwriters Laboratories.

This symbol

designates

that

this tool

complies

to NOM

Mexican

Standards.

This symbol designates that

this tool is listed by

Underwriters Laboratories,

and listed to Canadian

Standards by Underwriters

Laboratories.

BM 2610908996 6-04 6/21/04 4:47 PM Page 5

-6-

Functional Description and Specifications

Disconnect the plug from the power source before making any

assembly, adjustments or changing accessories

. Such preventive safety

measures reduce the risk of starting the tool accidentally.

!

WARNING

FIG. 1

SPEED CONTROL DIAL

Models 1617EVS

& 1618EVS only

SUB -BASE

TRIGGER

SWITCH

"LOCK-ON"

BUTTON

D-HANDLE

ROUND

HANDLE

BASE CLAMP LEVER

CHIP DEFLECTOR

MOTOR HOUSING

ROCKER ON\OFF SWITCH

POWER ON/OFF

SWITCH

TEMPLET GUIDE

QUICK CHANGE LEVER

MOTOR ALIGNMENT ARROW

FIG. 2

AIR VENTS

REVERSIBLE

HANDLE

BIT ROTATION ARROW

Routers

BASE TYPE S

BASE TYPE D

BM 2610908996 6-04 6/21/04 4:47 PM Page 6

-7-

2

1

0

IN

50

40

30

20

10

0

MM

FIG. 3

SPEED CONTROL DIAL

Model 1617EVSP only

SUB-BASE

PLUNGE HANDLE

CHIP DEFLECTOR

MOTOR HOUSING

ROCKER ON\OFF SWITCH

MOTOR ALIGNMENT

ARROW

AIR VENTS

BIT ROTATION ARROW

BASE TYPE P

Model number 1617 & 1618 1617EVS & 1618EVS 0 601 617 061

Voltage rating 120V 50 - 60Hz 120V 50 - 60Hz 220V 50 - 60Hz

Amperage rating 11A 12A 6A

No load speed n

0

25,000/min n

0

8,000-25,000/min n

0

25,000/min

Collet capacities 1/4", 3/8", 1/2", 8mm 1/4”, 3/8”, 1/2”, 8mm 1/4”, 3/8”, 1/2”, 8mm

RA1160 fixed-base shop router base marked type "S" is designed for use with these router motors:

1617 router motor (16171)

1617EVS router motor (16176)

0 601 617 061 router motor (0 601 617 161)

1618 router motor (16181)

1618EVS router motor (16186)

RA1162 D-handle router base marked type "D" is designed only for use with these router motors:

1618 router motor (16181)

1618EVS router motor (16186)

RA1166 plunge router base marked type "P" is designed for use with these router motors:

1617 router motor (16171)

1617EVS router motor (16176)

0 601 617 061 router motor (0 601 617 161)

1618 router motor (16181)

1618EVS router motor (16186)

PLUNGE LOCK LEVER

DEPTH ROD

DEPTH ROD KNOB

DEPTH STOP TURRET

DEPTH INDICATOR

DEPTH ROD FINE

ADJUSMENT KNOB

BM 2610908996 6-04 6/21/04 4:47 PM Page 7

-8-

Assembly

A wide assortment of router bits with different

profiles is available separately. Use 1/2"

shank whenever possible, and only use good

quality bits.

To prevent personal injury,

always remove the plug

from power source before removing or

installing bits or accessories.

INSTALLING A ROUTER BIT

Place router upside down or lay router on its

side with the base resting on the bench.

Another option is to remove the motor from

the base before installing the bit.

1. Remove the chip shield (or flip up if plunge

base is attached.

2. Hold the armature shaft in place with the

shaft wrench (Fig. 4)

3. Next, use the collet wrench to loosen the

collet chuck assembly in counter-

clockwise direction (viewed from under the

router).

4. Insert the shank of the router bit into the

collet chuck assembly as far as it will go,

then back the shank out until the cutters

are approximately 1/8" to 1/4" away from

the collet nut face.

5. With the router bit inserted and the shaft

wrench holding the armature shaft, use the

collet wrench to firmly tighten the collet

chuck assembly in a clockwise direction

(viewed from under the router). To ensure

proper gripping of the router bit and

minimize run-out, the shank of the router

bit must be inserted at least 5/8".

When the templet guide

has been removed from

base, do not use router bits greater than

2" in diameter as they will not fit through

the sub-base.

To prevent damage to tool,

do not tighten collet

without a bit.

NOTE:

The bit shank and chuck should be

clean and free of dust, wood, residue and

grease before assembling.

REMOVING THE ROUTER BIT

1. Use the shaft and collet chuck wrenches

as described earlier, and turn the collet

chuck assembly in a counter-clockwise

direction.

2. Once the collet chuck assembly is

loosened continue to turn the collet chuck

assembly until it pulls the collet free from

its taper, and the router bit can be

removed.

NOTE: The collet chuck is self-extracting; it

is NOT necessary to strike the collet chuck to

free the router bit.

COLLET CHUCK CARE

With the router bit removed, continue to turn

the collet chuck counter-clockwise until it is

free of the shaft. To assure a firm grip,

occasionally blow out the collet chuck with

compressed air, and clean the taper in the

armature assembly shaft with a tissue or fine

brush. The collet chuck is made up of two

component parts as illustrated (Fig. 5); check

to see that the collet is properly seated in the

collet chuck nut and lightly thread the collet

chuck back onto the armature shaft. Replace

worn or damaged collet chucks immediately.

!

WARNING

COLLET

NUT

FIG. 5

COLLET

CHUCK

SHAFT

WRENCH

COLLET

WRENCH

FIG. 4

!

WARNING

!

CAUTION

BM 2610908996 6-04 6/21/04 4:47 PM Page 8

REMOVING MOTOR FROM BASE

To remove motor from non-plunge bases:

(Fig. 6)

1. Hold router in horizontal position, open

base clamp lever, depress coarse

adjustment lever, and pull motor upwards

until it stops.

2. Turn motor counter-clockwise, and gently

pull it free of base.

To remove motor from plunge base: (Fig. 7)

1. Hold router in horizontal position, open

base clamp lever, and pull motor upwards

until it stops.

2. Turn motor counter-clockwise, and gently

pull it free of base.

INSTALLING MOTOR IN BASE

The motor can be installed with the switch

positioned on the right or left of the base from

the operator's side (and the cord facing the

opposite side of the router). Install the motor

so that the switch is in the location you find to

be the most easily accessible from the

handles. The switch should be easier to turn

"OFF" than "ON" in case of an emergency.

To install motor in non-plunge base:

1. Release the base clamp lever.

2. Line up the arrow on the base with arrow

on the motor. (Fig. 8)

• To position switch on the right side of the

base, line up the base’s arrow with

motor housing’s arrow that is below the

cord.

• To position switch on the left, line up the

base’s arrow with motor housing’s arrow

that is below the switch.

3. While pressing the coarse adjustment

lever, slide motor into base until resistance

in felt. (The base’s guide pin is now

engaged into slot on motor.)

4. Continue to press coarse adjustment lever,

and turn the motor clockwise until it stops.

5. Push the motor into the base until it

reaches the approximate desired depth.

6. Release the coarse adjustment lever and

slide the motor forward or back as needed

until the coarse adjustment system’s

“catch” springs into the coarse adjustment

detent notch.

7.

Set final height position as described

below in “Operating Instructions”.

To install motor in plunge base:

1. Release the base clamp lever.

2. Line up the arrow on the base with arrow

on the motor. (Fig. 8)

• To position switch on the right side of the

base, line up the base’s arrow with

arrow on the motor housing that is

below the cord.

-9-

ALIGNMENT

ARROWS

COARSE

ADJUSTMENT

NOTCHES

MOTOR

BASE

FIG. 8

BASE

CLAMP

LEVER

FIG. 6

COARSE

ADJUSTMENT

LEVER

BASE

CLAMP

LEVER

FIG. 7

BM 2610908996 6-04 6/21/04 4:47 PM Page 9

CHIP DEFLECTOR

Always wear eye

protection. The chip

deflector is not intended as a safety

guard.

The chip deflectors help keep dust and chips

out of your face, it will not stop objects larger

than dust thrown from the bit.

To remove chip shield from bases, press

inward on tabs until it releases from base and

remove. To attach, place deflector into

position as shown in (Fig. 10). Then flex

sides of deflector while pushing until it snaps

into place. The plunge base’s chip shield can

also be flipped out.

2

1

0

IN

50

40

30

20

10

0

MM

INSTALLING TEMPLET GUIDE ADAPTER

Place templet guide adapter over the holes in

the center of the sub-base, and align the two

threaded holes in the bottom of adapter with

the countersunk holes in sub-base. Fasten

adapter with the screws provided. Note that

the adapter is reversible, so the release lever

may be positioned as desired. (Fig. 9)

-10-

TEMPLET GUIDE

ADAPTER

MOUNTING SCREWS

FIG. 9

FIG. 10

!

WARNING

• To position switch on the left, line up the

base’s arrow with arrow on the motor

housing that is below the switch.

3. Slide motor into base until resistance in

felt. (The base’s guide pin is now engaged

into slot on motor.)

4. Turn the motor clockwise until it stops.

5. Push the motor into the base as far as it

will go.

6. Fasten the base clamp lever.

BM 2610908996 6-04 6/21/04 4:47 PM Page 10

Bosch routers are designed for speed,

accuracy and convenience in performing

cabinet work, routing, fluting, beading, cove-

cutting, dove tails, etc. They will enable you

to accomplish inlay work, decorative edges

and many types of special carving.

DEPTH ADJUSTMENT

WITH FIXED BASE

Your router is equipped with a true

micrometer type fine adjustment mechanism,

which can be used in any position and

provides precise adjustment of the router bit

position for unmatched accuracy. When the

tool is lowered to the approximate position

desired, this device may be adjusted to

precisely set the final bit position.

Your router also features three horizontal

notches on both sides of the motor housing

for coarse adjustments. The notches are

spaced 1/2" apart which allows you to quickly

lower or raise the tool depth in three 1/2"

increments. (Approximately 12.7 mm), by

simply depressing the coarse adjustment

release lever.

TO ADJUST DEPTH

NOTE:

All depth adjustments must be made

with the base clamp lever released.

1. Hold the tool in a horizontal position with

the base clamp lever facing you.

2. Open the base clamp lever to release the

motor.

3. COARSE ADJUSTMENT:

To make a large depth adjustment, depress

coarse adjustment release lever and raise or

lower to desired depth. There are three

notches in the motor housing which are

spaced 1/2" to facilitate this adjustment.

4. FINE DEPTH ADJUSTMENT:

To use the fine adjustment feature, turn the

fine adjustment knob clockwise to lower the

router bit or counter-clockwise to raise it.

NOTE: Be sure coarse adjustment lever is

engaged in one of the coarse adjustment

notches before making a fine adjustment.

To allow precise settings, the indicator ring is

graduated in English and Metric increments.

(Note: one full turn of fine adjustment knob =

1/16" or approximately 1.5 mm. The fine

adjustment mechanism has a total

adjustment range of 7/8" (23 mm). Each cast

indicator mark next to coarse adjustment

lever is equal to 1/8"

To prevent damage to tool, avoid wedging

the coarse adjustment lever against the

upper A or lower B portion of the housing as

shown in figure 11.

5. After making depth adjustments, re-clamp

the motor.

The indicator ring may be reset to zero

without moving the fine adjustment knob, to

allow the user to begin the adjustment from

any reference point desired.

-11-

Operating Instructions

A

B

FINE ADJUSTMENT DIAL

BASE CLAMP LEVER

COARSE

ADJUSTMENT

LEVER

INDICATOR RING

FIG. 11

CAST INDICATOR MARKS

BM 2610908996 6-04 6/21/04 4:47 PM Page 11

-12-

The RA1002 Fine Adjustment Control

Extension, an optional accessory for the non-

plunge bases, allows fine adjustment from

beyond the top of the motor housing. To

install, simply press the RA1002 into the end

of the base’s own fine adjustment knob.

(Fig. 12)

TO CLAMP MOTOR

When final coarse and fine adjustments have

been made, fasten the base clamp lever to

secure adjustments. (If additional clamping

force is desired: using a 10 mm wrench,

rotate clamp nut clockwise SLIGHTLY (1/8

turn or less), then test clamp. Do not over-

tighten.)

DEEP CUTS

For deeper cuts, make several progressively

deeper cuts by starting at one depth and

then make several subsequent passes,

increasing the cutting depth with each pass.

To be certain that your depth settings are as

desired, you may want to make test cuts in

scrap material before beginning work.

FIG. 12

DEPTH ADJUSTMENT WITH PLUNGE BASE

PLUNGING ACTION

The plunge feature simplifies depth

adjustments and will allow the cutting bit to

easily and accurately enter the workpiece. To

lower, push plunge lock lever to the left,

apply downward pressure until you reach

desired depth, and release pressure on lever

to lock (Fig. 13). The plunge lock lever is

spring loaded and returns automatically to

the locked position. To raise the router, push

plunge lock lever to the left, release pressure

on router and the router will automatically

retract the bit from the workpiece. It is

advisable to retract the bit whenever it is not

engaged in workpiece.

DEPTH ROD AND TURRET

The depth rod and the depth stop turret are

used to control cutting depth as follows;

1. With the bit installed, gently lower the

motor until the tip of the router bit just

contacts the level surface the router is

sitting on. This is the “zero” position, from

which further depth adjustments can be

accurately made.

2. To set a desired depth of cut, rotate depth

stop turret until the lowest step is aligned

with the depth rod. Loosen depth indicator

knob and lower the depth rod until it

contacts the lowest step of the turret. Slide

the depth indicator until the red line

indicates zero on the depth scale,

indicating the point at which the bit just

contacts the work (Fig. 14).

3. To set a desired cutting depth, slide the

depth rod up until the red depth indicator

line attains the desired cutting depth, and

secure the rod in position by firmly

tightening the depth indicator knob.

4. The desired depth of cut may now be

achieved by plunging the router until the

depth rod contacts the selected stop on

the turret.

FIG. 13

BM 2610908996 6-04 6/21/04 4:47 PM Page 12

DEEP CUTS

For deeper cuts, make several progressively

deeper cuts by starting with the highest step

on the depth turret, and after each cut, rotate

the depth turret to progressively lower steps

as desired, until the final depth (lowest step

or flat) is reached. Steps progress by 1/8”

increments.

To be certain that your depth settings are as

desired, you may want to make test cuts in

scrap material before beginning work.

FINE ADJUSTMENT

The RA1166 plunge base is equipped with a

fine adjustment system that allows you to

micro adjust the plunge depth of the router bit

for superior routing accuracy.

Each complete revolution of the fine

adjustment stop adjusts the plunging depth

by 1/32”, and each of the four indicator marks

on the knob represents 1/128”. One of the

four tick marks is larger than the other to

indicate a complete revolution. A reference

indicator line is built in to the depth rod.

To use the fine adjustment knob, once the

depth rod and turret have been set, check

the final depth setting and fine-adjust as

follows:

To micro-increase the plunge depth, raise the

fine adjustment stop by turning it counter-

clockwise by the desired amount.

To micro-reduce the plunge depth, lower the

fine adjustment stop by turning it clockwise

by the desired amount.

Notes:

• When micro-adjusting the plunge depth, it

is more convenient to move the fine

adjustment stop up than down. Before

setting the depth rod and turret, make sure

the fine adjustment stop has been turned

several revolutions down from its top

position so that it can be adjusted upward.

• The fine adjustment stop cannot be use to

reduce the plunge depth when the depth

rod is already touching the depth stop

turret. The router must be raised before

such an adjustment can be made.

-13-

2

1

0

IN

50

40

30

20

10

0

MM

FIG. 14

DEPTH INDICATOR

KNOB

DEPTH

INDICATOR

DEPTH ROD

DEPTH STOP

TURRET

DEPTH ROD FINE

ADJUSMENT KNOB

BM 2610908996 6-04 6/21/04 4:47 PM Page 13

-14-

ROCKER “ON/OFF” SWITCH

Your tool can be turned “ON” or “OFF” by the

rocker switch located on the motor housing.

One side of the switch is marked “I” for “ON“,

and the other side of switch is marked “O” for

“OFF“. Also the edge of switch displays red

when switch is in the “ON“ position.

TO TURN THE TOOL “ON”: Push the side

of the switch marked “I”.

TO TURN THE TOOL “OFF”: Push the side

of the switch marked “O”.

Always hold the router off the work when

turning the switch on or off. Contact the work

with the router after the router has reached

full speed, and remove it from the work

before turning the switch off. Operating in this

manner will prolong switch and motor life and

will greatly increase the quality of your work

(Fig. 1).

ROCKER POWER "ON-OFF" WITH

TRIGGER SWITCH AND "LOCK-

ON"BUTTON

(Models 1618 & 1618EVS only)

The power is switched "ON" by the rocker

switch located on the top of the motor

housing as described above. Now your tool

can be turned "ON" or "OFF" by squeezing or

releasing the trigger. Your tool is also

equipped with “Lock-ON” button located just

above the trigger that allows continuous

operation without holding the trigger (Fig. 2).

TO LOCK SWITCH ON: Squeeze trigger,

depress button and release trigger.

TO UNLOCK THE SWITCH: Squeeze trigger

and release it without depressing the “Lock-

ON” button.

If the “Lock-ON” button is

continuously being

depressed, the trigger cannot be released.

On models 1617 & 1618 hold the tool with

both hands while starting the tool, since

torque from the motor can cause the tool to

twist.

SOFT START FEATURE

(Models 1617EVS & 1618EVS only)

Electronic feedback control minimizes torque

twist customary in larger routers by limiting

the speed at which motor starts.

ELECTRONIC VARIABLE SPEED

CONTROL (Models 1617EVS & 1618EVS

only)

The electronic speed control feature allows

motor speed to be matched to cutter size and

material hardness for improved finish,

extended bit life, and higher performance.

Speed changes are achieved by rotating

Control Dial RIGHT to increase speed, LEFT

to decrease as indicated on housing (Fig. 1).

Speed may be changed while tool is on. The

reference numbers on the dial facilitate re-

setting control to desired speed.

The speed chart indicates the relationship

between settings and application, exact

settings are determined by operator

experience and preference. The bit

manufacturer may also have a speed

recommendation.

CONSTANT RESPONSE™ CIRCUITRY

(Models 1617EVS & 1618EVS only)

The router's Constant Response™ Circuitry

monitors and adjusts power to maintain the

desired RPM for consistent performance and

control.

!

WARNING

DIAL

SETTING RPM APPLICATION

1 8,000

2 13,500

3 16,500

4 20,000

5 21,500

6 25,000

}

Nonferrous metals,

larger diameter bits,

and cutters

Softwoods, plastics,

counter tops, smaller

diameter bits, and

cutters

BM 2610908996 6-04 6/21/04 4:47 PM Page 14

FEEDING THE ROUTER

As seen from the top of the router, the bit

turns clockwise and the cutting edges face

accordingly. Therefore, the most efficient cut

is made by feeding the router so that the bit

turns into the work, not away. Figure 15

shows proper feed for various cuts. How fast

you feed depends on the hardness of the

material and the size of the cut. For some

materials, it is best to make several cuts of

increasing depth.

If the router is hard to control, heats up, runs

very slowly or leaves an imperfect cut,

consider these causes:

1. Wrong direction of feed — hard to control.

2. Feeding too fast — overloads motor.

3. Dull bit — overloads motor.

4. Cut is too large for one pass — overloads

motor.

5. Feeding too slow — leaves friction burns

on work.

Feed smoothly and steadily (do not force).

You will soon learn how the router sounds

and feels when it is working best.

RATE OF FEED

When routing or doing related work in wood

and plastics, the best finishes will result if the

depth of cut and feed rate are regulated to

keep the motor operating at high speed.

Feed the router at a moderate rate. Soft

materials require a faster feed rate than hard

materials.

The router may stall if improperly used or

overloaded. Reduce the feed rate to prevent

possible damage to the tool. Always be sure

the collet chuck is tightened securely before

use. Always use router bits with the shortest

cutting length necessary to produce the

desired cut. This will minimize router bit run-

out and chatter.

-15-

GUIDING THE ROUTER

The router can be guided through the work in

any of several ways. The method you use

depends, of course, on the demands of the

particular job and on convenience.

For routing operations such as grooving or

dadoing, it is often necessary to guide the

tool in a line parallel to a straight edge. One

method of obtaining a straight cut is to

securely clamp a board or other straightedge

to the work surface, and guide the edge of

the router sub-base along this path (Fig. 16).

FIG. 15

FIG. 16

BIT

WORK

DIRECTION OF

ROUTER FEED

START

HERE

BOARD GUIDE

SECURELY CLAMP

BOARD GUIDE

FEED

DIRECTION

BM 2610908996 6-04 6/21/04 4:47 PM Page 15

CENTERING THE SUB-BASE AND

TEMPLET GUIDES

Your router features the Bosch “Precision

Centering Design”. Its sub-base is precisely

centered at the factory. This positions the bit

at the center of the sub-base and optional

templet guides. Precision centering allows

you to closely follow jigs such as straight

guides, templets, and dovetail fixtures

without worrying about bit walk-off from the

intended cut line for any reason, including the

orientation of the router’s handles.

In the event the sub-base screws are

loosened or removed, such when preparing

the router for use in a router table, here's

how to re-center the sub-base when

reattaching it:

To quickly re-center the sub-base, attach the

sub-base using the set of flathead screws

(included) and the countersunk screw holes

in the sub-base. (Flathead screws have the

tapered heads.) The flathead screws and

countersunk holes will pull the sub-base into

a position that is very close to centered.

OR — To most precisely re-center the sub-

base, attach the sub-base using the optional

Bosch centering cone, an optional Bosch

templet guide, and the set of pan-head

screws (included). (Pan-head screws have

rounded tops.) Follow steps 1-8.

1. Position the sub-base so that its pan-head

screw holes are over the matching set of

threaded holes in the base.

2. Insert the pan-head screws, not the

flathead screws, through the sub-base and

tighten them until they are snug, but still

allow the sub-base to move.

3. Insert templet guide (optional accessory)

the installed template guide adapter as

described elsewhere in this manual.

4. Slide centering cone (optional accessory)

through templet guide and into collet. Use

narrow end of cone when inserting into

1/4” collet, wider end of cone when

inserting into 1/2” collet.

5. Tighten collet nut with fingers to put slight

grip on centering cone.

6. Lightly press centering cone into templet

guide to center guide and sub-base.

7. Tighten the pan-head screws.

8. Remove centering cone. The precision

centering of the templet guide and sub-

base is complete.

-16-

A

B

A

C

A

C

A

B

CENTERING CONE

(optional accessory)

D D

B

A

B

A

B

A

C

D

FIG. 17

PLUNGE BASE

FIG. 18

OTHER BASES

CENTERING CONE

(optional accessory)

TEMPLET

GUIDE

(optional

accessory)

SUB-BASE

A

= COUNTERSUNK SCREW HOLES

B = PAN-HEAD SCREW HOLES

C = TEMPLET GUIDE ADAPTER

SCREW HOLES

D = HOLES FOR ATTACHING

ROUTER TO ROUTER TABLE

MOUNTING PLATE

(Under sub-base on

non-plunge bases)

BM 2610908996 6-04 6/21/04 4:47 PM Page 16

-17-

TEMPLET GUIDES

The router is equipped with an exclusive

quick-change templet guide adapter, which

firmly grips the guides with a spring-loaded

ring. To insert or change the templet guide,

retract the templet guide release lever. Align

the cutaways on the templet guide with the

tabs on the bottom of the templet guide

adapter. Insert the templet guide and release

the lever to grip the templet guide in place

(Fig. 19).

Templet guides are used with a number of

special accessories, such as hinge templets,

which are listed in your BOSCH catalog. In

addition, special templets are easily prepared

for cutting repeated patterns, special

designs, inlays, and other applications. A

templet pattern may be made of plywood,

hardboard, metal or even plastic, and the

design can be cut with a router, jigsaw, or

other suitable cutting tool. Remember that

the pattern will have to be made to

compensate for the distance between the

router bit and the templet guide (the “offset”),

as the final workpiece will differ in size from

the templet pattern by that amount, due to

the bit position (Fig. 20).

Also available as an optional accessory is an

additional adapter, the RA1100, that allows

use of conventional threaded templet guides

with the Bosch quick-release system.

TEMPLET GUIDE

(optional accessory)

TEMPLET GUIDE

ADAPTER

TEMPLET GUIDE

RELEASE LEVER

FIG. 19

COLLET CHUCK

WORKPIECE

ROUTER BIT

OFFSET

TEMPLET

GUIDE

TEMPLET

PATTERN

FIG. 20

ROUTER

SUB-BASE

ROUTER DUST COLLECTION

There are three optional dust extraction hood

accessories. Each dust extraction hood is

sized to accept 35mm vacuum hoses. Each

accessory pack includes the VAC002

adapter that will connect the hood to 1-1/4”

and 1-1/2” vacuum hoses. An adapter to

connect the hood to 2-1/2" hoses is also

available separately.

ROUTER DUST COLLECTION FOR

PLUNGE BASE

The RA1174 dust extraction hood is

designed for use the plunge base (RA1166)

when routing is done in the middle of the

workpiece, such as when creating slots or

routing patterns for inlays. If you have a shop

vacuum system, you can attach the dust

extraction hood for improved visibility,

accuracy and utility, particularly in freehand

routing.

To attach, position as shown and secure

adapter to base with the thumbscrews

provided (Fig. 21).

The dust extraction hood can also be

installed with the hose outlet facing the front

of the tool. If the templet guide adapter is

installed, it will need to be reversed or

removed to allow the release lever to fit

under the dust hood.

FIG. 21

DUST EXTRACTION HOOD

(Optional Accessory)

4mm THUMB

SCREWS

BM 2610908996 6-04 6/21/04 4:47 PM Page 17

-18-

RA1171 DUST EXTRACTION HOOD FOR

OTHER BASES

Do not reach in area of the

bit while the router is ON

or plugged in. To avoid entangling hoses,

do not use this dust extraction hood at

the same time as any other dust

extraction hood.

The RA1171 dust extraction hood is

designed for use with Bosch routers bases

“S” (RA1160) and “D” (RA1162), when the

routing is done in the middle of the

workpiece, such as when creating slots or

routing out patterns for inlays.

To attach the hood to the router base, slide

the hood into the backside of the router base

with the hood’s rounded corners facing up

(Fig. 22 & 23). Securely tighten the two

knurled thumbscrews.

For maximum dust collection effectiveness,

make sure the router’s chip shield is in place.

!

WARNING

DUST

EXTRACTION

HOOD

(Optional Accessory)

M5

SCREW

ROUTER

BASE

FIG. 22

FIG. 23

BM 2610908996 6-04 6/21/04 4:47 PM Page 18

-19-

RA1170 EDGEFORMING DUST

EXTRACTION HOOD

Do not reach in area of the

bit while the router is ON

or plugged in. To avoid entangling hoses,

do not use this dust extraction hood at

the same time as any other dust

extraction hood.

The RA1170 dust extraction hood (optional

accessory) is used for dust collection when

edge-forming (Fig. 24).

ATTACHING DUST EXTRACTION HOOD

You can attach the edge-forming hood in

several places according to your needs or

preferences. This hood is attached using two

of the screw holes on the router base that

are used to attach the router’s sub-base.

Choose the desired location for the hood.

Loosen and take out the two screws from the

router base and attach the dust extraction

hood — over the router’s sub-base — using

the screws provided with the hood. Securely

tighten the screws. (Figures 25 & 26).

DUST

EXTRACTION

HOOD

ROUTER

SUB-BASE

WORKPIECE

EDGE

!

WARNING

4mm x 16mm

SCREW

4mm x 16mm

SCREW

4mm x 16mm

SCREW

SUB-BASE

DUST

EXTRACTION

HOOD

4mm x 16mm

SCREW

FIG. 24

DUST

EXTRACTION

HOOD

FIG. 25

PLUNGE BASE

FIG. 26

OTHER BASES

BM 2610908996 6-04 6/21/04 4:47 PM Page 19

-20-

DELUXE ROUTER GUIDE

(Not included, available as accessory)

The Bosch deluxe router guide is an optional

accessory that will guide the router parallel to

a straight edge or allow you to create circles

and arcs.

The deluxe router guide is supplied with two

rods and screws to fasten the guide (Fig. 27).

In addition, it features a fine adjustment knob

and indicator for accurately positioning the

edge guide relative to the bit. With the guide

installed and adjusted, the router should be

fed normally, keeping the guide in contact

with the edge of the workpiece at all times.

The deluxe router guide may also be

positioned directly under the router base for

operations where a cut is needed close to or

at the edge of the work.

The deluxe router guide includes a dust

extraction hood and the VAC002 vacuum

hose adapter.

For complete instructions on installation and

operation, please refer to the instructions

which are included with this accessory.

FIG. 27

DESIRED

WIDTH

CUT

BASE

WORKPIECE

ROUTER

GUIDE

RODS

6mm WING

SCREW

6mm WING SCREW

FINE

ADJUSTMENT

KNOB

FINE ADJUSTMENT

INDICATOR

FEED

DIRECTION

BM 2610908996 6-04 6/21/04 4:47 PM Page 20

La page est en cours de chargement...

Bosch Power Tools 1617EVSPK Manuel utilisateur

Ce manuel convient également à

Bosch Power Tools 1617EVSPK Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents