Ohaus Scout Le manuel du propriétaire

Marque: Ohaus

Modèle: Scout

Taper: Le manuel du propriétaire

Ce manuel convient également à

30268985

Scout

Bluetooth

Interface

INSTRUCTION MANUAL

sales@novatech-usa.com

www.novatech-usa.com

Tel: (866) 433-6682 Fax: (866) 433-6684

Tel: (281) 359-8538 Fax: (281) 359-0084

(866) 433-6682 • (281) 359-8538 • [email protected] • www.novatech-usa.com

Bluetooth® Interface EN-1

INTRODUCTION

This Interface Kit is for use with Ohaus Scout STX, SPX, SKX and SJX series

products.

INTERFACE INSTALLATION

Install the Interface module on the mini DIN port (round connector) located at the

rear side of the balance as shown. During this process, please make sure the

balance is powered off.

Notes:

 Please make sure the small triangle mark (▲) on the round connector is at

the bottom and then plug in.

 The appearance of your model may be different.

SETUP

Upon installation of the interface, the balance will recognize the Bluetooth

®*

Interface and add relevant items to the menu. The display will show " " icon in the

upper right corner. The Device ID and Bluetooth address will be shown in the menu.

Bluetooth Interface Kit can be forward compatible with the Mobile or Tablet Devices

for Android

TM*

version 4.3 and Bluetooth 4.0. Please double check your Devices'

system version before connection.

OPERATION

Bluetooth APP installation: install the apk file on your

Mobile or Tablet for Android

The apk file can be obtained either by scanning the QR

code or by going to the below link and from there

download it. Then unzip the file to install it.

http://dmx.ohaus.com/WorkArea/showcontent.aspx?id=4294974211

* Android is a trademark of Google Inc.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,

Inc. and any use of such marks by OHAUS is under license.

Mini DIN port

(Round connector)

(866) 433-6682 • (281) 359-8538 • [email protected] • www.novatech-usa.com

EN-2 Bluetooth® Interface

CONNECTION

Once the APP is installed, the Bluetooth APP icon will be shown on your Mobile or

Tablet device. Open the APP and it will scan the ambient Bluetooth device

automatically. Click the correct Bluetooth device and start connecting.

Scanning. The display will then

show the list of available

Bluetooth devices.

Select your Bluetooth device &

establish the connection.

Note: check the Bluetooth Device

ID or Mac address on the data

label of the Bluetooth Interface

Kit.

Connected successfully:

(866) 433-6682 • (281) 359-8538 • [email protected] • www.novatech-usa.com

Bluetooth® Interface EN-3

APP MAN INTERFACE

Note: the display content might be different in different revisions.

Item

Description

Bluetooth Status, click to disconnect the Bluetooth interface

Weighing Display Area

Keys to operate the Balance

 Zero: Zero the balance

 Unit: Change the weighing unit

 Mode: Change the application mode

 Tare: Tare the balance

Start to collect the stable data (including zero & loading

values) from the balance.

Stop saving (it will show up after has been pressed.)

Show the storage path of saved file

Note: The saved file will be named as "YYYY_MM_DD_HH-MM-

SS.txt" (e.g. 2016_12_08_16-30-12.txt).

Model name of the Balance; SNR of the Balance

Application mode icon: Press the icon to change the application mode

Stable (*), Net (Net) or Center of Zero (>0<)

DEVELOPMENT

To develop your own Application, please use the following UUIDs to connect to the

Bluetooth Interface, and use the interface commands (listed below) to communicate

with the balance.

GATT

UUID

BluetoothGattDescriptor

00002902-0000-1000-8000-00805f9b34fb

BluetoothGattService

2456e1b9-26e2-8f83-e744-f34f01e9d701

BluetoothGattCharacteristic

2456e1b9-26e2-8f83-e744-f34f01e9d703

(866) 433-6682 • (281) 359-8538 • [email protected] • www.novatech-usa.com

EN-4 Bluetooth® Interface

The following Interface Commands will be acknowledged by the Balance. They are

case sensitive.

Command

Function

Immediate Print of displayed weight (stable or unstable).

Print displayed weight (stable or unstable).

Continuous Print.

Print on Stability.

SLP

Auto Print stable non-zero displayed weight.

SLZP

Auto Print stable non-zero weight and stable zero reading.

Interval Print x = Print Interval (1-3600 sec) 0P ends interval Print

Turn off Auto Print

H x “text” Enter Header line , where x = line number 1 to 5, “text” = header

text up to 24 alphanumeric characters

F x “text” Enter Footer line , where x = line number 1 to 2, “text” = footer

text up to 24 alphanumeric characters

Same as pressing Zero Key

Same as pressing Tare Key.

Establish a preset Tare value in displayed unit. x = preset tare value.

Sending 0T clears tare (if allowed).

Prints Tare weight stored in memory.

Print current application mode (weighing mode).

Set current application mode to x. x depends on application

1M: WEIGH, 2M: COUNT,3M: PERCENT, 4M: CHECK, 5M: DYNAMIC, 6M:

TOTAL, 7M:DENSITY, 8M: HOLD, 9M:MOLE

Scroll to the next enabled mode.

Print Current weighing unit: g, kg, lb, oz, etc….

Set balance to unit x: g, kg etc.

1U: g, 2U: kg,3U: ct, 4U: N, 5U: oz, 6U: ozt, 7U: dwt, 8U: lb, 9U:lb:oz, 10U:

grn, 11U: thk, 12U: tsg, 13U:ttw , 14U: tola, 15U:c

Scroll to the next enabled unit.

Brings out of Standby

OFF

Goes to Standby.

Begin Span Calibration

Abort Calibration.

PSN

Print Serial Number.

Print Version: print name, software revision and LFT ON (if LFT is set ON).

Set Counting APW (x) in grams. (must have APW stored)

Print Counting application APW.

Set Percent application reference weight (x) in grams. (must have reference

weight stored)

Print Percent application reference weight.

xCO

Set Checkweighing Over Limit in grams x.

xCU

Set Checkweighing Under Limit in grams x.

PCO

Print Checkweighing Over Limit.

PCU

Print Checkweighing Under Limit.

xMM

Set Molar Mass in g/mol .

PMM

Print Molar Mass

0 = print unstable data, 1 = print stable only

xFMT

0 = New Scout print format (default) ; 1 = Scout Pro print format 1;

2 = Scout Pro print format 2; 3 = for certain POS system.

xRL

0 = disable response; 1 = enable response.

(866) 433-6682 • (281) 359-8538 • [email protected] • www.novatech-usa.com

Bluetooth® Interface EN-5

COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Please note that changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

(866) 433-6682 • (281) 359-8538 • [email protected] • www.novatech-usa.com

EN-6 Bluetooth® Interface

DISPOSAL

In conformance with the European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE) this device may not be

disposed of in domestic waste. This also applies to countries outside

the EU, per their specific requirements.

Please dispose of this product in accordance with local regulations at

the collecting point specified for electrical and electronic equipment. If

you have any questions, please contact the responsible authority or

the distributor from which you purchased this device.

Should this device be passed on to other parties (for private or

professional use), the content of this regulation must also be related.

For disposal instructions in Europe, refer to www.OHAUS.com/weee.

Thank you for your contribution to environmental protection.

(866) 433-6682 • (281) 359-8538 • [email protected] • www.novatech-usa.com

OHAUS Corporation

7 Campus Drive

Suite 310

Parsippany, NJ 07054 USA

Tel: +1 973 377 9000

Fax: +1 973 944 7177

With offices worldwide/ Con oficinas en todo el mundo/ Avec des bureaux dans le

monde entier/ Mit Niederlassungen weltweit/ Con uffici in tutto il mondo /

世界各地的办事处 /전세계 사무소 / С офисами по всему миру / 世界中にオフィス

を持つ

www.ohaus.com

*30296497*

Printed in China / Impreso en China/ Imprimé en Chine / Gedruckt in China / Stampato in Cina

/ 在中国印刷的 / 중국에서 인쇄 / Отпечатано в Китае /中国で印刷されます

sales@novatech-usa.com

www.novatech-usa.com

Tel: (866) 433-6682 Fax: (866) 433-6684

Tel: (281) 359-8538 Fax: (281) 359-0084

Ohaus Scout Le manuel du propriétaire

Marque: Ohaus

Modèle: Scout

Taper: Le manuel du propriétaire

Ce manuel convient également à

30268985

Télécharger le PDF

rapport

dans d''autres langues

English: Ohaus Scout Owner's manual

Ohaus Scout Le manuel du propriétaire

Ce manuel convient également à

Ohaus Scout Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents