brondell IS707-EW Manuel utilisateur

OWNER’S MANUAL

Swash IS707 Advanced Bidet Toilet Seats

IS707-EW

IS707-RW

Attach Proof of Purchase to This Page

Adjunte prueba de compra a esta página

Joindre une preuve d’achat à cette page

1

CONTENTS

This manual contains important safety information. Before operating the

bidet, please read this manual thoroughly, and retain it for future reference.

PRODUCT INSTALLATION

GENERAL INFO

PRODUCT OPERATION

02 SAFETY INFORMATION

06

07

08

PRODUCT INFORMATION

Product Features

Product Dimensions

Product Parts

09

10

13

PRODUCT INSTALLATION

Installation Parts

Before Installation

Swash Installation

External Bidet Filter Installation

14

16

18

OPERATING THE SWASH

IS707 Control Panel

Using the Swash IS707

Special Mode Operations

TECHNICAL INFO

TRANSLATIONS

19 PRODUCT SPECIFICATIONS

20

21

MAINTENANCE

Seat Cleaning & Removal

Nozzle Cleaning

Cleaning the Mesh Filter

Product Storage & Use

22 TROUBLESHOOTING

25 WARRANTY

26 CONTACT

1 ENGLISH

27 SPANISH

54 FRENCH

2

Failure to observe the following warnings may result in electric shock, ﬁre, personal injury, property

damage or product damage:

• Do not use a damaged power plug or plug into a loose electric outlet.

• Do not move the product by pulling the power cord.

• Do not handle the product or power plug with wet hands.

• Do not forcefully bend the power cord or place heavy objects on it to prevent it from being damaged

or deformed.

• Do not connect and pull out the power plug or cord repeatedly.

• Unplug the product before cleaning, repairing, inspecting, or replacing parts.

• Remove any dust or water from the power plug prior to plugging in.

• Do not plug the product into an electrical outlet or power strip that is being used by too many other

products. Use an electrical outlet adequate for the wattage of the product rated for a minimum of 15

amps.

• If the power cord is damaged, do not attempt to repair, modify, or replace the cord yourself. Contact

the Brondell Service Center toll free at 888-542-3355 or email us through our website.

• If the product produces a strange noise, a burning smell, or emits smoke, unplug it immediately

from the electrical outlet and contact Brondell. Failure to do so may result in electric shock or ﬁre.

• Do not insert any wires or sharp objects into any product gaps. This may result in electric shock, ﬁre,

or product damage.

Be careful to keep this safety information. Please read this information

to prevent property loss and ensure safety.

SAFETY INFORMATION

IMPORTANT SAFEGUARDS

DANGER:

If not observed, serious injury or even death may occur as a result.

DANGER

WARNING:

If not observed, serious physical injury or property damage may occur as a result.

CAUTION:

If not observed, minor physical injury or property damage may occur as a result.

READ ALL INSTRUCTIONS BEFORE USING

SAVE THESE INSTRUCTIONS

3

• Do not place an electronic or gas heater near the product or dispose of any burning materials

such as a lit cigarette in the toilet. This may result in ﬁre or product deformation. Do not place any

containers ﬁlled with water or other liquids, food, metallic objects, or any ﬂammable material on top

of the product. If foreign material enters the product, this may result in electric shock or ﬁre.

• Do not use the product in locations exposed to excessive moisture and do not splash water onto the

product.

• While cleaning the bathroom, pull the power plug out of the electrical outlet and exercise caution to

ensure that water or cleaning supplies do not splash onto the bidet. Failure to do so may result in

electric shock or ﬁre.

• If foreign material enters the product, pull the power plug out of the electrical outlet, turn o the

main water valve, and call the Brondell Service Center.

• Do not disassemble, repair, or modify the product yourself.

• Do not use the product while wet from bathing or showering.

• Do not place or store the product where it can fall or be pulled into a tub or sink.

• Do not place in or drop the product into water or any other liquid.

• Do not reach for the product if it has fallen into water. Unplug the product immediately and call the

Brondell Service Center.

• Do not use the product if it is not working properly. Please unplug the product immediately, close

the main water supply valve, and call the Brondell Service Center at 888-542-3355. Failure to do so

may result in electric shock, ﬁre, or ﬂooding.

SAFETY INFORMATION (cont.)

IMPORTANT SAFEGUARDS

DANGER

SAVE THESE INSTRUCTIONS

Failure to observe the following warnings may result in electric shock, ﬁre, personal injury, property

damage or product damage.

• Do not plug in, operate, or store the unit in locations where ﬂammable or combustible materials are

used or kept.

• Do not use industrial water, or gray water for the supply, as this may cause skin damage or disease.

• Turn o the main water supply valve when cleaning.

• For children and seniors who may have diculties with adjusting temperatures or those with sen-

sitive skin or impaired heat sensitivity, set the temperature of the wash spray and seat to “low” or

“o” to prevent burning.

• Close supervision is necessary when this product is used by children, seniors, or persons requiring

general assistance.

• Do not press the buttons using excessive force.

• Do not stand on top of or place any heavy objects onto the seat cover.

• Use this product for its intended use only, as described in this manual. Do not use any attachments

that are not recommended by Brondell.

WARNING

4

SAFETY INFORMATION (cont.)

IMPORTANT SAFEGUARDS

SAVE THESE INSTRUCTIONS

Failure to observe the following warnings may result in electric shock, ﬁre, personal injury, property

damage, or product damage.

• Do not connect the main water supply to the hot water pipe or supply (only connect to the cold

water supply).

• After the installation, make sure to check all water supply connections for leaks. Rubber washers

should be in place for the water connection hoses & T-Valve.

• Do not open/close the seat or seat cover with excessive force.

• Exercise caution that urine does not come into contact with the product - failure to do so may result

in bad odors or malfunction.

• If the product will not be used for a long period of time, unplug the power cord, close the main

water supply valve, and drain any water in the water tank.

• Do not pull out the bidet hose using excessive force.

• Do not use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent on or near

the product. This may result in corrosion to the metal parts or discoloration or scratches to the bidet

body.

• This appliance is not intended for use by persons (including children and seniors) with reduced

physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning the use of the appliance by a person responsible

for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

CAUTION

WARNING

• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has

been dropped or damaged, or dropped into water. Contact the Brondell Service Center for examina-

tion and repair.

• Keep the cord away from heated surfaces and heating vents.

• Never block the air openings of the product or place it on a soft surface, such as a bed or couch,

where the air openings may be blocked. Keep the air openings free of lint, hair, etc.

• Never drop or insert any object into any opening or hose.

• Do not use the product outdoors or operate where aerosol (spray) products are being used or a

room where it could be exposed to oxygen.

• Connect this product to a properly grounded outlet only. Refer to the Grounding Instructions in the

next pages of the manual.

5

This product should only be used with a grounded GFCI

(Ground Fault Circuit Interrupter) outlet and a grounded

three-prong electrical cord as shown to the right. In the

event of an electrical short circuit, using a grounded GFCI

outlet reduces the risk of electric shock.

This product is equipped with a grounded cord and is for

use on a nominal 120V circuit only (minimum 15 amps) and

must be plugged into an outlet that is properly grounded

with a GFCI breaker as shown. Replace or repair a damaged

cord immediately.

Extension Cord Use

If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps with a

three-wire extension cord with a three-blade grounding plug. Only plug into a three-slot grounded

GFCI receptacle that will accept the plug of the product. Replace or repair any damaged cords

immediately.

GROUNDING AND GFI OUTLET INSTRUCTIONS

Test

Reset

Ground GFCI Outlet

Grounding Pin

Improper use of the grounding plug can result in a risk of electric shock.

• If repair or replacement of the cord or plug is necessary, do not connect the

grounding wire to either ﬂat blade terminal. The wire with green insulation

(either with or without a yellow stripe) is the grounding wire.

• Check with a qualiﬁed electrician if the grounding instructions are not completely

understood, or if there is doubt if the product is properly grounded.

SAFETY INFORMATION (cont.)

IMPORTANT SAFEGUARDS

SAVE THESE INSTRUCTIONS

6

PRODUCT INFORMATION

Stainless-Steel Nozzle System - Stainless steel resists soiling and bacterial contamination for

enhanced hygiene.

Posterior and Feminine Warm Water Wash – experience the ultimate in clean with adjustable

temperature, position, pressure, massage, and oscillation settings.

Positionable Nozzle – the nozzle has ﬁve dierent positions to ensure the most comfortable and

complete wash.

Adjustable Water Temperature and Pressure – each wash mode (Front and Rear) has four

available water temperature settings, and ﬁve water pressure settings.

Massage – when activated, the water pressure automatically increases and decreases to provide a

pulsating, cleaning spray.

Warm Air Dryer – includes adjustable temperature with ﬁve levels for a hands-free experience and

toilet paper reduction – even elimination.

Nozzle Oscillation – the Move function provides a massaging, oscillating cleanse during the wash

cycle ensuring a thorough and comfortable wash.

Auto Function – activates a preset for a rear wash cycle followed by a drying cycle.

Ergonomic Heated Seat – with four temperature settings (High/Med/Low/O).

Illuminating Nightlight – the cool blue hue of the nightlight means no more blinding lights during

midnight trips to the bathroom.

Gentle-Closing Seat and Lid – “slam free” gentle closing seat and lid are user friendly.

Eco Mode – when activated, this function automatically lowers the water and seat temperature.

PRODUCT FEATURES

7

PRODUCT DIMENSIONS

5.5 in

Required Distance Between

Mounting Holes

18.2 in

14.9 in

7.8 in

2.7 in

16.4 in

15.2 in

13.6 in

4.3 in

Elongated Top View

Round Top View

8

PRODUCT PARTS

PRODUCT INFORMATION (cont.)

1. Lid

2. Seat Sensor

3. Warm Seat

4. Warm Air Dryer

5. Nozzle Assembly

6. LED Nightlight

7. Control Panel

8. Power Plug

9. Water Inlet with Mesh Filter

10. Drain Plug

11. Mounting Plate

8

9

10

7

6

1

11

5

4

2

3

9

INSTALLATION PARTS

1. Mounting Bolt (2)

2. Rubber Cone Washer (2)

3. Flat Washer (2)

4. Nuts (2)

5. Mounting Plate

1

5

2

3

6

4

6. Top-Mount Brackets (2)

7. T-Valve Connector with

Rubber Washer

8. Bidet Hose

8

7

PRODUCT INSTALLATION

10

DO NOT PLUG THE PRODUCT IN WHILE THE UNIT IS UPSIDE DOWN

This may cause damage to the internal components.

WATCH OUR INSTALLATION VIDEO

Installation for all Swash products can be found online at brondell.com

CHECK BOLT SPREAD

This bidet can only be installed on toilets with a bolt hole spread of 5.5 inches (see Product

Dimensions on Page 7 for more information).

CHECK FOR TOP MOUNT INSTALLATION

If your ﬁxture only has top-side access to the mounting bolts that hold the seat to the toilet,

include the Top-Mount Brackets included in the hardware pack (see Page 12).

CHECK FOR A CONCEALED TOILET FILL VALVE

Many modern toilets have sleek designs intended to cover and camouﬂage plumbing

connections, which makes a standard Swash installation dicult or impossible. For this, we

recommend using our Alternate Swash Bidet Seat T-Valve, found on brondell.com.

CHECK WATER SUPPLY LINE

Check the line that connects the toilet tank to the water shut o valve. If it is a rigid pipe, you may

need to purchase a ﬂexible hose to replace it before installing the Swash. The length of the hose

and the size of the connectors will vary.

RESIDUAL MOISTURE IS NORMAL

Every product is tested with pure water during production to ensure the highest quality and

performance. It is normal to ﬁnd a small amount of residual moisture on the product and in the

reservoir and ﬁlter.

TOOLS

A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a

standard wrench may be needed for tight water supply connections. Teﬂon tape can be helpful in

creating a water-tight seat between plumbing connections.

PRODUCT INSTALLATION (cont.)

BEFORE INSTALLATION

SWASH INSTALLATION

1. Existing Toilet Seat Removal

a. Lift hinge covers and use a screwdriver to remove the mounting bolts.

b. Remove the toilet seat. Keep for future use.

Please read these instructions carefully before installing the Swash. Failure to do so could result

in ﬂooding, leaking or damage to the product.

11

NOTE: Steps may vary by type of seat and toilet

SWASH INSTALLATION (cont.)

3. Connect the top of the T-Valve to the incoming water

connection on the bottom of your toilet tank.

4. Connect the water supply line coming from the wall to the

bottom of the T-Valve

5. Install Mounting Plate for Standard Installation (see

Page 12, Step 6 for instructions on using the Top-Mount

Brackets)

a. Place adjustable mounting plate over mounting holes

on toilet, rubber side facing down, arrow pointing to the

toilet bowl.

b. Insert the mounting bolts through the mounting plate

and mounting holes of the toilet. Be sure that the

square mounting bolt head is even with the sides of the

mounting plate.

c. Slide rubber cone washer, ﬂat washer, and then nut

onto mounting bolts under the toilet bowl and tighten to

keep mounting plate in place.

NOTES:

• The T-Valve connects to the ﬁll valve directly under

your toilet tank - it does not connect at the wall.

• Only connect to the cold toilet water supply line.

• If your water supply line is rigid you may need to

replace it before continuing.

Steps 5b & 5c

Steps 3-4

toilet tank

t-valve

cold water

supply line

NOTES:

• You may wish to place a container under the tank to

catch any excess water.

• Do not continue without completing the above steps

• Failure to do so could result in ﬂooding, leaking or

damage to the Swash.

2. Turn O Water Supply Valve and Flush Toilet

a. Turn water valve o to stop the ﬂow of water.

b. Flush toilet and hold down handle to completely

empty tank.

c. Disconnect water supply hose from toilet tank. Do not

disconnect from the water supply valve.

Step 2c

12

PRODUCT INSTALLATION cont.

SWASH INSTALLATION (cont.)

9. Connect the open end of the Bidet Hose to the T-Valve.

8. Attach the Swash to the Mounting Plate

a. Set the Swash ﬂat on the toilet bowl in front of the

mounting plate, and slide seat onto plate until it is

secure.

b. If the seat appears too short or too long for the toilet,

adjust the mounting plate accordingly. To adjust the

mounting plate, loosen the nuts underneath the toilet

and slide seat forward or backwards as needed. Once

the seat is lined up properly, tighten the nuts to hold in

place.

7. Connect the Bidet Hose to the Seat

a. Connect the elbow side of the bidet hose to the water

inlet. Hand-tighten to secure. Take care not to twist the

bidet hose, excessively bend it, or strip the plastic screw

threads when screwing the hose onto the bidet seat.

11. Plug the Power Cord into an Electrical Outlet

a. If the Power Indicator is not illuminated press any

button on the control panel.

10. Turn On Water Supply

a. Open the main water supply valve slowly and check

for leaks.

b. Wait 5 minutes, check again and if there are no leaks

continue.

Step 8b

Step 7a

Step 9

6. Install Mounting Plate for top-mounted toilet seats (see

Page 11, Step 5 for instructions on Standard Installation).

This method will use a combination of the included Top-

Mount Brackets and the original toilet seat mounting bolts.

a. Place adjustable mounting plate over mounting holes

on toilet, rubber side facing down, arrow pointing to the

toilet bowl.

b. Place the provided Top-Mount Brackets ﬂat side down

into the slots of the Mounting Bracket, over the bolt

holes.

c. Insert the original toilet seat mounting bolts through the

Top-Mount Brackets and into the threaded bolt holes of

the toilet, using a screwdriver to tighten.

Steps 6b & 6c

13

SWASH INSTALLATION (cont.)

NOTES:

• Make sure to only use a grounded GFCI (ground fault circuit interrupter) electrical outlet. In

the case of a short circuit, a grounded GFCI outlet may help prevent electric shock or injury.

• If it is necessary to use an extension cord, only use those rated for a minimum of 15 amps

with a three-wire extension cord with a three-blade grounding plug.

12. Press the “REAR WASH” button on the control arm to ﬁll the water tank. The bidet will beep

continuously while it ﬁlls and then issue one long beep when the water tank is full. Wait 3-5

minutes for the water to heat, and then the Swash will be ready to use.

13. Follow instructions on Page 16 for using the Swash.

EXTERNAL BIDET FILTER INSTALLATION

1. Turn O Water Supply Valve and Flush Toilet.

a. Turn water valve o to stop the ﬂow of water.

b. Flush toilet and hold down handle to completely empty tank.

2. Disconnect the Bidet Hose from the T-Valve

3. Connect the female end of the Swash Filter to the open T-Valve connection.

4. Connect the Bidet Hose to the male end of the Swash Filter.

5. Turn the toilet water supply valve back on.

Step 2

FLOW

Step 3

FLOW

Step 4

NOTE:

• Customers with hard water, well water, and softened water can extend the life of their bidet

seat by purchasing and installing an external inline water ﬁlter to be used with the Swash.

The bidet ﬁlter should be changed every six months, and can be purchased online at

brondell.com.

14

OPERATING THE SWASH

IS707 CONTROL PANEL

Water Temperature

Button and Indicators

Nozzle Position Buttons

Water Pressure and

Dry Temperature

Buttons and Indicators

Seat Temperature

Button and Indicators

9

8

7

6

Eco Mode Button

and Indicator

Power Indicator

Auto Mode Button

Night Light Button

and Indicator

10

11

12

13

1

3

4

2

Massage Button

Stop Button

Front Wash /

Move Button

Rear Wash /

Move Button

Warm Air Dry Button

5

15

IS707 CONTROL PANEL (cont.)

1. Stop Button

Stops all wash and dry functions currently operating. Press and hold this button for four

seconds to power o the bidet.

2. Rear Wash / Move Button

Press once to initiate a rear wash. Press again to initiate nozzle oscillation (repetitive forward

and backward nozzle movement).

3. Front Wash / Move Button

Press once to initiate a front wash. Press again to initiate nozzle oscillation (repetitive forward

and backward nozzle movement).

4. Dry Button

Press once to initiate a two minute Warm Air Dryer cycle.

5. Massage Button

Pressing this button while a wash is running enables the water to repeatedly increase and

decrease in pressure in a pulsating pattern. Press again to stop the massage.

6. Water Pressure and Dry Temperature Buttons and Indicators

Press the “+” and “–” buttons to increase and decrease the outgoing water pressure to one of

ﬁve settings. Pressing these buttons while the Warm Air Dryer is operating will adjust the Drying

temperature. Settings will be saved for the next use.

7. Nozzle Position Buttons

Press the arrow up and arrow down buttons to adjust the nozzle position forward and backward

during a wash cycle. Between uses the nozzles will revert back to the middle position.

8. Water Temperature Button and Indicators

Press and release the “Water Temp” button to adjust the outgoing water temperature to one of

four settings (LO: 93.2° F, MED: 98.6° F, HI: 104° F, and OFF). Settings will be saved for the

next use.

9. Seat Temperature Button and Indicators

Press and release the “Seat Temp” button to adjust the seat temperature to one of four settings

(LO: 95° F, MED: 100.4° F, HI: 104° F, and OFF). Settings will be saved for the next use.

10. Power Indicator

This indicator will light up when the bidet is powered on, and will be o when the bidet is

powered o. To turn o the bidet press and hold the “STOP” button for at least four seconds.

11. Eco Mode Button and Indicator

Press and release the “Eco Mode” button to select or turn o Eco Mode. The indicator will light

up when the Eco Mode has been selected. See Page 17 for more information.

12. Night Light Button and Indicator

Press the “Night Light” button to enable the Night Light (the indicator light will be illuminated).

Press again to disable the Night Light and indicator.

13. Auto Mode Button

Press this button once to initiate a one minute rear wash cycle followed by a one minute dry

cycle. See Page 17 for more information.

16

OPERATING THE SWASH cont.

USING THE SWASH IS707

Warm Water Wash

When ready to wash, press the “Rear Wash” or “Front Wash” button on the control panel one time

to initiate a wash. The nozzle will self-clean, extend into the toilet bowl, spray for two minutes,

turn o automatically, retract, and self-clean once again.

1. Pressing the “Rear” or “Front” button a second time while the wash is running will cause the

nozzle to oscillate forward and backward, providing a wider range of wash spray. Press again

to cancel the move function.

2. While washing, users can adjust the water temperature, pressure, and nozzle position settings,

as well as initiate the massage feature by following the notes on Page 15.

3. If you would like to stop the wash before the two minute cycle ends, press the “Stop” button to

discontinue water ﬂow.

4. After extended use the water may decrease in temperature if a LO, MEDIUM, or HI water

temperature setting is selected. To regain warmer water, stop all wash functions for three

minutes to allow the bidet to reheat the water.

Prepare for Wash

Sit on the seat to ensure skin-to-seat contact on the Seat Sensor. Once contact is made the seat

will automatically perform many functions:

1. The seat will give an audible beep letting you know the Seat Sensor has been engaged.

2. The water pressure indicator lights will come on displaying the current setting.

3. If the bidet was set to Eco Mode, the seat and water temperature will rise to the set

temperature settings.

Warm Air Dryer Function

Press the “Dry” button to activate the warm air dryer. The dryer will run for two minutes and turn

o automatically.

1. While the air dryer is operating, users can adjust the dryer temperature to a comfortable level

using the Dry “

+”

and “–” buttons. The dry temperature will be reﬂected on the ﬁve indicator

LEDs.

2. If you would like to stop the dryer before the two minutes has elapsed, press Stop.

NOTES:

• The wash functions will not work unless the sensor in the seat detects someone sitting

down (with the built-in skin conductivity sensor). To override the Seat Sensor, please see

the instructions on Page 18.

17

USING THE SWASH IS707 (cont.)

Auto Mode

Pressing the “Auto Mode” button will initiate a one-minute Rear Wash with the following

parameters preset:

• Seat Temperature set to Medium

• Nozzle Oscillation (Move) on

• Water Pressure set to Level 3

• Water Temperature set to Medium

After the wash cycle is over, Auto Mode will initiate a one-minute Warm Air Dry cycle on Level 2.

Note: All wash and dry settings are adjustable, while the Auto Mode wash cycle is running, to suit

your preferences

Eco Mode

In this mode the water in the tank and the seat temperature will be heated to 86°F when the

bidet is not in use. Once a person sits on the bidet the Swash will revert to the last seat and water

temperature settings used. To select this option press and release the “Eco Mode” button to

illuminate its indicator.

18

OPERATING THE SWASH cont.

SPECIAL MODE OPERATIONS

Seat Sensor Override

The Seat Sensor is activated at the factory by default. Completing the following steps will bypass

the body sensor located in the seat and allows the wash functions and dry functions to operate

without the sensor being engaged. Use caution in this mode.

1. Unplug the Swash bidet seat.

2. Press the two Water Pressure/Dry Temp buttons (+ and –) and plug the seat in while holding

the two buttons down.

3. Keep holding the two Water Pressure/Dry Temp buttons (+ and –) down for ﬁve seconds.

A beep will sound, indicating that the Seat Sensor has been overridden. To test that the

procedure worked, press the Dry button. If the Warm Air Dryer comes on without anyone

sitting on the seat, you have successfully overridden the Seat Sensor.

4. You can resume using the seat as normal.

5. To reactivate the Seat Sensor, repeat Steps 1-3.

NOTE:

• Do not sit on the seat when in Special Mode Operations. The process will not work while

the seat is occupied.

Activating/Deactivating Silent Mode

By default, the Swash will beep to conﬁrm commands from the control panel. Follow the steps

below to silence the beeping sounds.

1. Press and hold down the Rear Wash/Move button and the “–” Water Pressure/Dry Temp button

at the same time for four seconds.

2. A beep will sound, indicating that the Silent Mode has been activated.

3. To deactivate Silent Mode, repeat Steps 1-2.

La page charge ...

brondell IS707-EW Manuel utilisateur

Ce manuel convient également à

brondell IS707-EW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents