TSC ALPHA-3R Manuel utilisateur

i

USER’S

MANUAL

Alpha-3R

Direct Thermal Portable Printer

ii

Copyright Information

The copyright in this manual, the software and firmware in the printer

described therein are owned by TSC Auto ID Technology Co., Ltd, All

rights reserved.

CG Triumvirate is a trademark of Agfa Corporation. CG Triumvirate Bold

Condensed font is under license from the Monotype Corporation. Windows

is a registered trademark of Microsoft Corporation.

All other trademarks are the property of their respective owners.

Information in this document is subject to change without notice and does

not represent a commitment on the part of TSC Auto ID Technology Co.

No part of this manual may be reproduced or transmitted in any form or by

any means, for any purpose other than the purchaser’s personal use,

without the expressed written permission of TSC Auto ID Technology Co.

iii

Agency Compliance and Approvals

CE CLASS B

EN 55022:2006 +A1:2007

EN 55024:1998+A1:2001+A2:2003

EN 61000-4 SERIES REQULATIONS

FCC CFR Title 47 Part 15 Subpart B:2011 Class B

ICES-003 Issue 4:2004 Class B

Wichtige Sicherheits-Hinweise

1. Bitte lesen Sie diese Hinweis sorgfältig durch.

2. Heben Sie diese Anleitung fűr den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromentz zu trennen. Verwenden Sie

keine Flüssig-oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes

Tuch zur Reinigung.

4. Die Netzanschluß-Steckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schűtzen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen

oder Fallen könnte Beschädigungen hervorrufen.

7. Beachten Sie beim Anschluß ans Stromnetz die Anschlußwerte.

8. Dieses Gerät kann bis zu einer Außentemperatur von maximal 40℃ betrieben

werden.

Battery safety warning:

DO NOT throw the battery in fire.

DO NOT short circuit the contacts.

DO NOT disassemble the battery.

DO NOT throw the battery in municipal waste.

The symbol of the crossed out wheeled bin indicates that the battery should not be

placed in municipal waste.

iv

Class B:

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device

could void the user's authority to operate the equipment.

RF exposure warning (WiFi)

This equipment must be installed and operated in accordance with provided

instructions and must not be co-located or operating in conjunction with any other

antenna or transmitter. End-users and installers must be providing with antenna

installation instructions and transmitter operating conditions for satisfying RF

exposure compliance.

SAR Value: 0.023 W/kg

RF exposure warning (For Bluetooth)

The equipment complies with FCC RF exposure limits set forth for an uncontrolled

environment.

The equipment must not be co-located or operating in conjunction with any other

antenna or transmitter.

v

Canada, Industry Canada (IC) Notices

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Industry Canada

(IC) radio frequency exposure limits. The Wireless Device should be used in such

a manner such that the potential for human contact during normal operation is

minimized.

This device has been evaluated for and shown compliant with the IC Specific Absorption

Rate (“SAR”) limits when installed in specific host products operated in portable

exposure conditions. (For WiFi)

This device has also been evaluated and shown compliant with the IC RF Exposure limits

under portable exposure conditions. (antennas are less than 20 cm of a person's body).

(For Bluetooth)

Canada, avis d'Industry Canada (IC)

Cet appareil numérique de classe B est conforme aux normes canadiennes

ICES-003 et RSS-210.

Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas

causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les

interférences qui peuvent affecter son fonctionnement.

Informations concernant l'exposition aux fréquences radio (RF)

La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite

d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de

sans fil de façon à minimiser les contacts humains lors du fonctionnement normal.

Ce périphérique a été évalué et démontré conforme aux limites SAR (Specific Absorption

Rate – Taux d'absorption spécifique) d'IC lorsqu'il est installé dans des produits hôtes

particuliers qui fonctionnent dans des conditions d'exposition à des appareils portables. (For

WiFi)

vi

Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux

RF d'IC dans des conditions d'exposition à des appareils portables. (les antennes sont moins

de 20 cm du corps d'une personne). (For Bluetooth)

vii

Contents

1. Introduction ................................................. 1

1.1 Product Introduction ......................................................................................... 1

1.2 Product Features ............................................................................................... 2

1.2.1 Printer Standard Features ...................................................................... 2

1.2.2 Printer Optional Features ....................................................................... 3

1.3 General Specifications ...................................................................................... 3

1.4 Print Specifications ........................................................................................... 4

1.5 Media Specifications ......................................................................................... 4

2. Operations Overview .......................................... 5

2.1 Unpacking and Inspection ................................................................................ 5

2.2 Printer Overview ................................................................................................ 6

2.2.1 Front View ............................................................................................... 6

2.2.2 Interior View ............................................................................................ 7

2.2.3 Rear View ................................................................................................ 8

2.3 Operator control ................................................................................................ 9

2.3.1 LED Indication and Keys ........................................................................ 9

3. Setup ..................................................... 11

3.1 Install the Battery ............................................................................................ 11

3.2 Charge the Battery .......................................................................................... 12

3.2.1 Charge the Battery ................................................................................ 12

3.2.2 Charge by Charger Station (Optional) ................................................. 13

3.2.3 Charge by Vehicle Power Adaptor (Optional) ..................................... 14

3.3 Communicate .................................................................................................. 15

3.3.2 Connecting with the Communication Cable ....................................... 15

3.3.2 Connecting with Bluetooth (Optional) ................................................. 16

3.4 Loading the Media ........................................................................................... 17

4. Accessories ................................................ 19

4.1 Install the Belt Clip ......................................................................................... 19

4.2 Install the IP54-rated environmental case with shoulder strap (Optional) .. 20

5. Power-on Utilities ........................................... 21

5.1 Black Mark Sensor Calibration ...................................................................... 21

5.2 Self-test and Dump Mode ............................................................................... 22

5.3 Printer Initialization ........................................................................................ 24

6. Diagnostic Tool ............................................. 26

6.1 Start the Diagnostic Tool ............................................................................... 26

viii

6.2 Printer Function .............................................................................................. 27

6.3 Calibrating Media Sensor by Diagnostic Tool .............................................. 28

6.3.1 Auto Calibration .................................................................................... 28

6.4 Setting Wi-Fi by Diagnostic Tool ................................................................... 29

6.5 Setting Bluetooth by Diagnostic Tool ........................................................... 30

7. Troubleshooting ............................................ 31

7.1 Common Problems ......................................................................................... 31

8. Maintenance ............................................... 33

Revise History ................................................ 34

1

1. Introduction

1.1 Product Introduction

Thank you very much for purchasing TSC bar code printer.

Enjoy TSC’s reputation for cost-efficient, high durability printers with the Alpha-3R

economical receipt printer. The Alpha-3R is a comfortable, light-weight printer capable

of working with any mobile receipt printing application where you need quick, simple

receipts on demand. Our Alpha-3R is designed for a rough life, inside the IP54-rated

environmental case to resist dust and water and with its rubber over-mold design

prepared to take up to a five foot fall and keep printing.

These small and light printers can be worn comfortably for a full shift, without interfering

with the user’s tasks. Use USB, or optional Bluetooth® , 802.11 b/g/n Wireless or Serial

to connect to a mobile computer or even a smart phone and produce clear easy-to-read

receipts hour after hour.

This document provides an easy reference for operating the Alpha-3R.

The online version of the Programmer's manual, or more information can be

downloaded from service and support web site as an Adobe Acrobat Reader file.

To print label formats, please refer to the instructions provided with your labeling

software; if you need to write the custom programs, please refer to the TSPL/TSPL2

programming manual that can be found on the accessories CD-ROM or on TSC website

at http://www.tscprinters.com

 Applications

 Direct store deliveries (DSD)

 Field repair/installation

 Mobile point of sale

 Parking citations

 Mobile ticketing

 Onboard transportation ticketing

 Utility billing/meter reading

2

1.2 Product Features

1.2.1 Printer Standard Features

The printer offers the following standard features.

Product standard feature

Alpha-3R

Direct thermal printing

○

Reflective sensor

○

Head open sensor

○

3 operation buttons (On/off, feed, and cover-open)

○

2 color LED for printer status, 3 LEDs for battery status

○

USB 2.0 (full speed) interface

○

8 MB SDRAM memory

○

4 MB FLASH memory

○

Powerful 32 bit 200 MHz RISC processor

○

Eltron

®

and Zebra

®

emulation languages support

○

Internal 8 alpha-numeric bitmap fonts

○

Fonts and bar codes can be printed in any one of the four

directions (0, 90,180, 270 degree)

○

Internal Monotype Imaging

®

true type font engine with

one CG Triumvirate Bold Condensed scalable font

○

Downloadable fonts from PC to printer memory

○

Downloadable firmware upgrades

○

Text, bar code, graphics/image printing (Please refer to the

TSPL/TSPL2 programming manual for supporting code page)

Supported bar code

Supported image

1D bar code

2D bar code

BITMAP,

BMP,

PCX

(Max. 256 colors

graphics)

Code 39,

Code 93,

Code128UCC,

Code128 subsets

A,B,C, Codabar,

Interleaved 2 of 5,

EAN-8, EAN-13,

EAN-128,

UPC-A, UPC-E,

EAN and UPC 2(5)

digits add-on, MSI,

PLESSEY,

POSTNET,

China POST,

GS1 DataBar,

PDF-417,

Maxicode,

DataMatrix,

QR code,

Aztec,

○

3

1.2.2 Printer Optional Features

The printer offers the following optional features.

Product option feature

User

options

Factory

options

802.11 b/g/n wireless

○

Bluetooth 2.0

○

CPCL emulation

○

Black mark sensor position

(left / right / center)

○

Charge station 1 cell

(with changeable power connector)

○

Vehicle power adapter

○

IP54-rated environmental case with

shoulder strap

○

USB to RS-232 cable

○

USB cable

○

Li-ion battery

○

1.3 General Specifications

General Specifications

Physical dimensions

116 mm (W) x 148 mm (H) x 70 mm (D)

Weight

550 g (1.21 lb)

Electrical

DC 7.4V/ 2500 mA/ h rechargeable battery

Environmental

condition

Operation: -10 ~ 50˚C (32 ~ 104˚F), 10 ~ 90% non-condensing

Storage: -40 ~ 60 ˚C (-40 ~ 140˚F), 10 ~ 99% non-condensing

4

1.4 Print Specifications

Print Specifications

Alpha-3R

Print head resolution

203 dots/inch (8 dots/mm)

Printing method

Direct thermal

Dot size

0.125 x 0.125 mm

(width x length)

(1 mm = 8 dots)

Print speed

2, 3, 4 ips selectable

(inches per second)

Up to 4 ips

Max. print width

72 mm (2.83”)

Max. print length

2286 mm (90”)

Printout bias

Vertical: 1 mm max.

Horizontal: 1 mm max.

1.5 Media Specifications

Media Specifications

Alpha-3R

Media roll capacity

57 mm (2.25”) OD

Media type

Receipt paper

Bline receipt paper

(Black mark in printing side)

Media wound type

Printing face outside wound

Media width

Max. 80 mm (3.15”)

Media length

Max. 38 m (125 ft)

Min. 21 m (69 ft)

Media thickness

Max. 0.10 mm (4 mil)

Min. 0.05 mm (2 mil)

Media core diameter

Max. 19 mm (0.75”)

Min. 10.2 mm (0.4”)

5

2. Operations Overview

2.1 Unpacking and Inspection

This printer has been specially packaged to withstand damage during shipping. Please

carefully inspect the packaging and printer upon receiving the bar code printer. Please

retain the packaging materials in case you need to reship the printer.

Unpacking the printer, the following items are included in the carton.

 One printer unit

 One Li-ion battery

 One Windows labeling software/Windows driver CD disk

 One quick installation guide

 One power adaptor

If any parts are missing, please contact the Customer Service Department of your purchased

reseller or distributor.

6

2.2 Printer Overview

2.2.1 Front View

1. LED indicator

2. Feed button

3. Power on/off button

4. Media cover release button

5. Media holder adjustment knob

6. Media cover

1

2

3

4

5

6

7

2.2.2 Interior View

1. Tear edge

2. Print head

3. Media holder

4. Platen

5. Black mark sensor

2

1

4

3

5

8

2.2.3 Rear View

1. Li-ion battery

2. Battery open clasp

3. USB interface

4. Power jack

5. Interface cover

3

2

4

1

5

9

2.3 Operator control

2.3.1 LED Indication and Keys

1. Power on/off button

2. Printer status LED indicator

3. Battery charge level LED indicator

4. Battery status LED indicator

5. Wireless status LED indicator

6. Feed button

LED

Status

Indication

Printer status LED indicator

Off

Pinter is ready

Green (blinking)

Printer is paused

Red (solid)

Media cover is open

Red (blinking)

Printer error

Battery status LED indicator

Green (blinking)

Recharge the battery

Amber (solid)

Battery is charging

Battery charge level LED

indicator

Green

(solid)

Full charged

2/3 charged level

1/3 charged level

Wireless status LED indicator

Blue (solid)

Wireless device is ready

Blue (blinking)

Wireless device is

communicating

2

3

4

5

1

6

10

Keys

Function

1. Press and hold for 2-3 seconds to turn on the printer.

2. Press and hold for 2-3 seconds to turn off the printer.

1. Feed one label when printer is ready.

2. Pause the print gob while printing.

11

3. Setup

3.1 Install the Battery

1. Insert the left side to install the

battery at the rear of the printer.

2. Push the right side of the battery.

3. Pull the battery clasp to lock the

battery.

Battery safety warning:

DO NOT throw the battery in fire. DO NOT short circuit the contacts.

DO NOT disassemble the battery. DO NOT throw the battery in municipal waste.

The symbol of the crossed out wheeled bin indicates that the battery should not be placed in

municipal waste.

PUSH

12

3.2 Charge the Battery

3.2.1 Charge the Battery

1. Open the interface cover and

plug the power cord to the power

jack.

2. Plug the power cord into a

properly power outlet.

Note:

Please switch OFF printer power prior

to plug in the power cord to printer

power jack.

When the battery is charging, please do

not remove the battery from the printer,

otherwise, please re-plug the power

cord into a power outlet.

3. When the battery is charging,

the color of battery status LED

indicator is solid amber.

Note:

When charging over 4 ~ 8 hrs, the

battery is completely charged and the

amber of LED indicator will be off.

La page charge ...

TSC ALPHA-3R Manuel utilisateur

TSC ALPHA-3R Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents