Barco Orion Cinemascope Guide de démarrage rapide

Barco
Marque
Barco
Modèle
Orion Cinemascope
Catégorie
Supports de projecteur
Taper
Guide de démarrage rapide
Mounting the flexible hose
4
1
Getting started
2
This Quick Start Guide has been designed to aid in quickly getting started with mounting and using the accessories obtained. If you require further help or information, please
refer to the projector user guide or our web site. You can also access FAQs, and download detailed white papers in order to get to know the more specific features and benefits.
Packaging contents for full kit (exceptions in brackets):
When mounting the flexible hose on the exhaust air, please notice the following:
Important to know
3
Keep in mind the following when installing the air exhaust kit:
• Make sure that the individual parts enter their locations effortlessly and that the screws are not overtightened when fastened.
• Do not block the air inlet or the exhaust air outlet. Hot air is exhausted from the rear air outlet. Do not place any objects sensitive to heat
near to the exhaust vent. Do not curl up or store additional cable lengths inside the ceiling mount cover (section 1/part 3).
• Minimum safety distance to the unit (with kit mounted) is 50 cm / 20” to the air inlet side: The distance to ceiling must be at least 15 cm / 6”.
For the other side of the projector (with no air inlet/outlet) and the top (facing down), no distance restrictions apply.
• If air-inlet filter is installed, the filter must be removed and cleaned at regular intervals.
• Do not mount this kit on a projector used in any other position than ceiling mounted!
• Make sure to mount the flexible hose correctly, as seen in section 4 below.
1 Air-inlet filter (sold separately)
2 Side cover/Air-inlet
3 Ceiling mount cover/Air-outlet (sold separately)
4 Exhaust air duct (including flexible hose with clamp)
2/3/4 Exhaust air kit (combined) 2/3 Acoustic silencer kit (combined)
601-0348-00
Quick Start Guide
Air-inlet filter
Ceiling mount cover
Exhaust air kit
User documentation
1
3
2
4
The Exhaust air kit is delivered without an Air-inlet filter (1 - illustration above), but the filter can be purchased separately and added either with or without the rest
of the kit. The Ceiling mount cover (3 - illustration above) is included in the Exhaust air kit, but can also be purchased separately.
Air-inlet filter (1 - illustration above): To mount the Air-inlet filter, fit the filter onto the grill and make sure the extruding plastic guide enters the inlet grill properly. Attach
the Air-inlet filter to the grill using the 3 supplied screws, two long screws on the left hand side and one shorter screw on the right hand side. If part of a kit, make sure to
mount the filter first. For mounting of other parts, see description in the following sections below. Mounting a filter is registered by the projector and a reminder to clean or
replace the filter will appear when required.
Ceiling mount cover (no. 3 - illustration above): Attach the cover by entering the plastic guides into the fitting holes at the back of the projector (upper edge) . Snap the
cover onto the rear end of the projector, making sure that the 2 extensions with screw holes are positioned over the corresponding holes in the projector chassis. Fasten by
entering the supplies screws. Make sure that the screws enter correctly and do not overtighten. If you have a complete kit, see exhaust duct description below first.
Exhaust duct (no. 4 - illustration above): If you have a kit, the exhaust duct needs to be mounted on the ceiling mount cover before attaching the cover to the projector.
First you need to loosen the chamber wall separating the padded exhaust chamber from the rest of the cover by removing 2 screws (Section 4 - right hand side). Position the
exhaust duct, angle pointing backwards, entering the slot on the cover side facing outwards. Make sure that the protruding retainer enters the back cover rim correctly when
pushed backwards into place. Place the chamber wall back in initial position and fasten the 2 wall screws. Finally fasten the 2 screws connecting the wall to the exhaust duct.
Side cover (no. 2 - illustration above): In order to mount the side cover the ceiling mount cover has to be mounted first. Position the side cover so that the screw holes at
the rear end of the projector fits into the countersink in the ceiling mount cover and the holes at the front end of the side cover are positioned above the corresponding holes
in the projector. Enter the screws (short screws at rear end/long at front end of projector) and fasten.
Flexible hose for exhaust duct (section 4 - right hand side): Thread the flexible hose for the exhaust air onto the exhaust duct and fasten it with the hose clamp.
A Exhaust air kit assembly without Air-inlet filter C How the finished mounted kit should look
B Exhaust air kit assembly including Air-inlet filter D Air flow directions for the Exhaust air kit (blue = inlet air / red = exhaust).
Minimum 15 cm
clearance to any
object
Never sharper than 90
0
bend
If exhaust is directed into a false ceiling,
this area should be well vented. Make
sure the ventilation does not override
the projector fans
5-inch (125 mm) diameter flexible hose
Maximum length of flexible hose
200 cm
Note! The exhaust air kit is only intended for use with ceiling mounted projectors
50cm
15cm
For further information on ceiling mounting of your projector, see the user manual or our web page
4567
Remove chamber
wall (1) in ceiling
mount cover before
attempting to mount
the exhaust air duct
(2) (two screws)
1
2
Mounting Air-inlet filter / Ceiling mount cover / Exhaust air kit
A
C
B
D
601-0378-00
Visit www.barco.com to download product manuals or information
www.barco.com
WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste
electrical and electronic equipment (WEEE). This product shall be recycled
properly. It can be disassembled to facilitate proper recycling of it’s individual
parts.
Consult your dealer or relevant public authority regarding drop-off points for collection
of WEEE.
WEEE-ANGABEN
Dieses Produkt erfüllt alle Auflagen aus der EU-Richtlinie für Elektro- und
Elektronik-Altgeräte (WEEE). Dieses Produkt kann sachgemäß recycelt werden.
Es kann zerlegt werden, um die Einzelteile ordnungsgemäß zu recyceln.
Fragen Sie Ihren Händler oder die zuständigen Behörden nach
Entsorgungsstellen für Elektro- und Elektronik-Altgeräte.
INFORMATION WEEE
Cet appareil est conforme à la Directive EU relative au recyclage des
équipements électriques et électroniques (WEEE). Cet appareil doit être
recyclé correctement. Il peut être démonté pour faciliter le recyclage de
chaque pièce séparément.
Consultez votre revendeur ou les autorités publiques compétentes concernant les
points de collecte WEEE.
INFORMACIÓN WEEE
Este producto cumple todos los requisitos de la Directiva de la UE sobre
residuos de equipos eléctricos y electrónicos. Este producto debe reciclarse
adecuadamente. Puede desmontarse para facilitar el adecuado reciclado de
cada una de sus piezas.
Consulte a su distribuidor o al organismo público pertinente acerca de los puntos
limpios para la recogida de residuos de equipos eléctricos y electrónicos.
INFORMAZIONI SU WEEE
Questo dispositivo è conforme a tutti i requisiti della direttiva UE (WEEE) sullo
smaltimento di apparecchiature elettriche ed elettroniche. Questo prodotto
deve essere riciclato correttamente e può essere smontato per agevolare il
riciclaggio dei singoli componenti.
Per informazioni sui punti di raccolta WEEE, consultare il rivenditore o l’autorità
preposta.
WEEE INFORMATION
Dette produktet tilfredsstiller alle krav i EU direktivet 2002/96/EC somgjelder
brukt elektrisk og elektronisk utstyr. Dette produktet skal resirkuleres forsvarlig.
Det kan demonteres slik at de enkelte deler kan resirkuleres forsvarlig.
Kontakt din forhandler eller relevant offentlig myndighet angående
returpunkter for innsamling av WEEE.
english
deutsch
francais
español
italiano
norsk
WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste
electrical and electronic equipment (WEEE). This product shall be recycled
properly. It can be disassembled to facilitate proper recycling of it’s individual
parts.
Consult your dealer or relevant public authority regarding drop-off points for collection
of WEEE. For details, please visit the Barco website at: http://www.barco.com/en/
AboutBarco/weee.
WEEE-ANGABEN
Dieses Produkt erfüllt alle Auflagen aus der EU-Richtlinie für Elektro- und
Elektronik-Altgeräte (WEEE). Dieses Produkt kann sachgemäß recycelt werden.
Es kann zerlegt werden, um die Einzelteile ordnungsgemäß zu recyceln.
Fragen Sie Ihren Händler oder die zuständigen Behörden nach
Entsorgungsstellen für Elektro- und Elektronik-Altgeräte. Für weitere Informationen,
besuchen Sie bitte die Website unter: http://www.barco.com/en/AboutBarco/weee.
INFORMATION WEEE
Cet appareil est conforme à la Directive EU relative au recyclage des
équipements électriques et électroniques (WEEE). Cet appareil doit être
recyclé correctement. Il peut être démonté pour faciliter le recyclage de
chaque pièce séparément.
Consultez votre revendeur ou les autorités publiques compétentes concernant les
points de collecte WEEE. Pour plus de détails, veuillez visiter le site web Barco à:
http://www.barco.com/en/AboutBarco/weee.
INFORMACIÓN WEEE
Este producto cumple todos los requisitos de la Directiva de la UE sobre
residuos de equipos eléctricos y electrónicos. Este producto debe reciclarse
adecuadamente. Puede desmontarse para facilitar el adecuado reciclado de
cada una de sus piezas.
Consulte a su distribuidor o al organismo público pertinente acerca de los puntos
limpios para la recogida de residuos de equipos eléctricos y electrónicos. Para
obtener más información, visite la página web de Barco: http://www.barco.com/en/
AboutBarco/weee.
INFORMAZIONI SU WEEE
Questo dispositivo è conforme a tutti i requisiti della direttiva UE (WEEE) sullo
smaltimento di apparecchiature elettriche ed elettroniche. Questo prodotto
deve essere riciclato correttamente e può essere smontato per agevolare il
riciclaggio dei singoli componenti.
Per informazioni sui punti di raccolta WEEE, consultare il rivenditore o l’autorità
preposta. Per ulteriori informazioni, visitare il sito web Barco: http://www.barco.com/
en/AboutBarco/weee.
WEEE INFORMATION
Dette produktet tilfredsstiller alle krav i EU direktivet 2002/96/EC somgjelder
brukt elektrisk og elektronisk utstyr. Dette produktet skal resirkuleres forsvarlig.
Det kan demonteres slik at de enkelte deler kan resirkuleres forsvarlig.
Kontakt din forhandler eller relevant offentlig myndighet angående
returpunkter for innsamling av WEEE. For mer informasjon, se Barco sin webside:
http://www.barco.com/en/AboutBarco/weee.
  • Page 1 1
  • Page 2 2

Barco Orion Cinemascope Guide de démarrage rapide

Barco
Marque
Barco
Modèle
Orion Cinemascope
Catégorie
Supports de projecteur
Taper
Guide de démarrage rapide
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes