Honeywell HVC0001/U Mode d'emploi

Owner’s Guide

Guide du propriétaire

Guía del usuario

HVC0001 / HVC0002

Programmable Bath Fan Control

Contrôleur de ventilateur programmable

Controlador de ventilador programable

400-305-000-B (69-2316EFS-03).book Page 1 Monday, September 28, 2009 11:06 AM

Home

69-2316EFS-09

Read and save these instructions.

À lire et conserver en lieu sûr.

Estas instrucciones deben leerse y conservarse

400-305-000-B (69-2316EFS-03).book Page 2 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

ENGLISH

Overview

About your programmable bath

fan control......................................... 2

Quick reference................................ 3

Installation

2-wire installation.............................. 4

4-wire installation.............................. 5

Setup

Ventilation Mode parameters............ 6

Time and date .................................. 7

Backlight mode................................. 8

Daylight saving time ......................... 9

Modes of Operation

Ventilation mode .............................10

Customized cycle mode..................12

Daily On/Off mode ..........................14

Manual mode ..................................16

Countdown mode ............................ 17

Appendices

Product specifications.....................18

Customer assistance ......................19

5-year limited warranty ...................20

Table of contents

400-305-000-B (69-2316EFS-03).book Page 1 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

2

ENGLISH

The bath fan control has been designed to control a single-speed bath fan. To suit your lifestyle, it can

be programmed in any of the following modes of operation:

• Ventilation Mode (see page 10)

• Customized Cycle Mode (see page 12)

• Daily On/Off Mode (see page 14)

• Manual Mode (see page 16)

Unlike the four programmable modes mentioned above, the Countdown Mode can easily be

activated by simply pressing a button (see page 17). In this mode, the fan is on until the end of the

programmed countdown time when the controller returns to the programmed mode.

This

controller cannot be used with a load lower than 0.17 A or higher than 2.5 A.

The controller can be used to control a bath fan’s built-in light or a separate light

fixture connected to the bath fan control circuit. However, the light cannot be

independently controlled and will turn On or Off at the same time as the fan.

About your programmable bath fan control

400-305-000-B (69-2316EFS-03).book Page 2 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

3

ENGLISH

Quick reference

The LED illuminates

when the bath fan is On.

Press the Main Button to turn the

bath fan On or Off. (Press for 3

seconds to enter the setup menus.)

Press either button to place in

Countdown Mode. Then press the

left button to decrease the

countdown time or the right button

to increase the time.

Setup menu

Clock

The bath fan is On The bath fan is Off

Programmable modes

Countdown time

If the controller is also used to control

lights, pull out this safety tab before

replacing the light bulb. Push back in

after the light bulb is replaced.

Countdown Mode

(see page 17)

400-305-000-B (69-2316EFS-03).book Page 3 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

4

ENGLISH

nCut power at the main electrical panel to avoid electric shock.

oRemove the existing switch if applicable.

pInstall the bath fan controller.

qApply power at the circuit breaker.

2-wire installation

black

white

black (LINE)

black (LOAD)

green (GND)

120

VAC

black

white

For installation in wet locations, protect the circuit

with a ground fault circuit interrupter (GFCI).

400-305-000-B (69-2316EFS-03).book Page 4 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

5

ENGLISH

nCut power at the main electrical panel to avoid electric shock.

oRemove the existing switch if applicable.

pInstall the bath fan controller.

qApply power at the circuit breaker.

4-wire installation

120

VAC

black

white

black

white black (LINE)

black (LOAD)

green (GND)

For installation in wet locations, protect the circuit

with a ground fault circuit interrupter (GFCI).

400-305-000-B (69-2316EFS-03).book Page 5 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

6

ENGLISH

At first power-up, you will be prompted to set the following parameters:

Set the Ventilation Mode parameters

Select Units

(US /Metric)

Set Fan Capacity ***

(CFM or LPS)

ASHRAE 62.2

Pass/Fail ****

Set Floor Size **

(Sq. ft or Sq. M)

Set no. of

Bedrooms *

Normal

Display

* No. of bedrooms (1, 2, ..., 6)

** Floor space (1000, 1100, ..., 5000 sq. ft. or 100, 110, ..., 500 m2)

*** Fan capacity (30, 40, ..., 200 CFM or 15, 20, ..., 100 LPS)

**** The controller shows whether you pass or fail ASHRAE

Standard 62.2 for ventilation and the percentage of time the fan

will run every hour. If the controller indicates Fail; this usually

means the fan capacity is insufficient for your house.

If you press the main button for 3 seconds or do

not press any button for 60 seconds, the

controller will go to normal display. If the

parameters are not set, you will again be

prompted the next time the controller is powered

up, for example, after a power outage. The

parameters can be set at any time (see page 10).

400-305-000-B (69-2316EFS-03).book Page 6 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

7

ENGLISH

Set the time and date

Set Hour Set Minutes

Set Year Set Month Set Day

Select 24H or 12H

The time flashes on the screen when it is

not yet set or after a power outage of

more than 4 hours. To set the clock,

press the main button for 3 seconds to

display the setup menu and proceed as

shown.

Press the main button for 3 seconds at

any time (or do not press any button for

60 seconds) to save any changes you

have made and exit the setup menu.

400-305-000-B (69-2316EFS-03).book Page 7 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

8

ENGLISH

The controller provides 3 backlight modes. Depending on the mode selected, the screen behaves as

follows:

•Scrn Off: The screen is not lit (the backlight is off).

•Scrn On HI: The screen is lit at high intensity.

•Scrn On LO: The screen is lit at low intensity (default mode).

When you press any button, the screen is lit at high intensity for 8 seconds.

Set the Backlight mode

Set Backlight

(2 times)

Press the main but-

ton for 3 seconds at

any time (or do not

press any button for

60 seconds) to save

any changes you

have made and exit

the setup menu.

To set the backlight

mode, press the

main button for 3

seconds to display

the setup menu and

proceed as shown:

400-305-000-B (69-2316EFS-03).book Page 8 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

9

ENGLISH

When Automatic Daylight Savings Time changeover is enabled (DST On), the controller automatically

switches to daylight savings time (summer time) at 2:00 am on the second Sunday of March and back to

standard time (winter time) at 2:00 am on the first Sunday of November. This function is enabled by

default.

Set the Automatic Daylight Savings Time Changeover

Set Daylight

Saving Time

(2 times) (2 times)

To set the Automatic

Daylight Savings Time

Changeover, press the

main button for 3

seconds to display the

setup menu and

proceed as shown:

Press the main but-

ton for 3 seconds at

any time (or do not

press any button for

60 seconds) to save

any changes you

have made and exit

the setup menu.

400-305-000-B (69-2316EFS-03).book Page 9 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

10

ENGLISH

Press the main button for 3 seconds at any time (or do not press any button for 60 seconds) to save any changes you have

made and exit the setup menu.

Ventilation Mode

Select Units

(US /Metric)

Set Fan Capacity

(CFM or LPS) ASHRAE 62.2

Pass/Fail

Set Floor Size

(Sq. ft or Sq. M)

Set no. of

Bedrooms

Press simultaneously

In Ventilation Mode, the controller sets the fan On/Off time to meet ASHRAE Standard 62.2 for

ventilation based on total floor space, number of bedrooms and fan capacity. In this mode, the

fan operates on a 60-minute cycle. For example, if the fan is On for 20 minutes, it will be Off for

40 minutes. To set the Ventilation Mode parameters, press the main button for 3 seconds to

display the setup menu and proceed as shown.

400-305-000-B (69-2316EFS-03).book Page 10 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

11

ENGLISH

To place

the controller

in Ventilation Mode, proceed as shown:

Temporary override

Press the main button to temporarily turn the fan On or Off. For example, if you press the

main button to turn the fan On during the idle period, the fan will remain On until the

beginning of the next idle period or until you press the main button again.

Ventilation Mode (cont’d)

Select

Ventilation Mode

Normal Display

(3 sec.) (3 sec.)

400-305-000-B (69-2316EFS-03).book Page 11 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

12

ENGLISH

In Customized Cycle Mode, you set the amount of time the fan is On (Run Period) or Off (Idle Period).

Each period can be set between 10 minutes and 120 minutes in increments of 5 minutes. The controller

will cycle between the two periods. For example, if you set the Run Period to 10 minutes and the Idle

Period to 20 minutes, you have established a cycle of 30 minutes. During every cycle, the fan will turn On

for 10 minutes and Off for 20 minutes.

Press the main button for 3 seconds at any time (or do not press any button for 60 seconds) to save any

changes you have made and exit the setup menu.

Customized Cycle Mode

Set Run Period Set Idle Perio

d

(3 times)

The Run Period and Idle Period

are available only if the controller

is in Customized Cycle Mode

(see opposite page). To set the

periods, press the main button for

3 seconds to display the setup

menu and proceed as shown:

400-305-000-B (69-2316EFS-03).book Page 12 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

13

ENGLISH

To place the controller in Customized Cycle Mode, proceed as shown:

Temporary override

Press the main button to temporarily turn the fan On or Off. For example, if you press the

main button to turn the fan On during the idle period, the fan will remain On until the

beginning of the next idle period or until you press the main button again.

Customized Cycle Mode (cont’d)

Select Customized

Cycle Mode

Customized Cycle Mode

Normal Display

(3 sec.) (3 sec.)

400-305-000-B (69-2316EFS-03).book Page 13 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

14

ENGLISH

In Daily On/Off Mode, the fan turns On and Off once a day according to the programmed On Time

and Off Time.

Press the main button for 3 seconds at any time (or do not press any button for 60 seconds) to

save any changes you have made and exit the setup menu.

Daily On/Off Mode

Set On Time Set Off Time

(3 times)

The On Time and Off Time

are available only if the

controller is in Daily On/Off

Mode (see opposite page).

To set the On Time and Off

Time, press the main

button for 3 seconds to

display the setup menu

and proceed as shown:

400-305-000-B (69-2316EFS-03).book Page 14 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

15

ENGLISH

To place the controller in Daily On/Off Mode, proceed as shown:

Temporary override

Press the main button to temporarily turn the fan On or Off. For example, if you press the

main button to turn the fan On, it will remain On until the programmed Off time or until you

press the main button again.

Daily On/Off Mode (cont’d)

Select Daily

On/Off Mode

Daily On/Off Mode

Normal Display

(3 sec.) (3 sec.)

400-305-000-B (69-2316EFS-03).book Page 15 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

16

ENGLISH

In Manual Mode, the controller operates like a regular switch. In this mode, simply press the

main button to turn the fan On or Off.

To place the controller in Manual Mode,

proceed as shown:

Manual Mode

Select

Manual Mode

Normal Display Manual Mode

(3 sec.) (3 sec.)

400-305-000-B (69-2316EFS-03).book Page 16 Monday, September 28, 2009 11:06 AM

HVC0001/HVC0002

17

ENGLISH

Place the controller in Countdown Mode to run the fan for 10-60 minutes. The fan turns On when the

controller is in this mode. At the end of the countdown time, the controller returns to its programmed mode

and the fan turns Off. (NOTE: The fan might stay On if the controller has been set to turn the fan On at

that given time in the programmed mode.)

You can cancel the Countdown Mode and return to the programmed mode at any time by pressing the

main button.

To place the controller in Countdown Mode,

proceed as shown:

Countdown Mode

After

5 sec.

Set Countdown

Time (minutes) *

Countdown Mode

is activated

At end of Countdown Mode

Normal Display _+

* Press the left or right button once

to use the same countdown time

as the one used the last time.

Press the left (-) or right (+) button

more than once to decrease or

increase the countdown time (in

increments of 5 minutes).

400-305-000-B (69-2316EFS-03).book Page 17 Monday, September 28, 2009 11:06 AM

Owner’s Guide 69-2316EFS

18

ENGLISH

HVC0001:

HVC0002:

Voltage:

Frequency:

Minimum Load:

Maximum Load:

Minimum Power Factor:

white

biscuit

120 VAC - 15%, + 10%

60 Hz ± 5%

0.17 A (20 W)

2.5 A (300 W)

0.60

Operating Temperature Range: -15°C to 50°C (5°F to 122°F)

Storage Temperature Range: -40°C to 60°C (-40°F to 140°F)

Product Specifications

400-305-000-B (69-2316EFS-03).book Page 18 Monday, September 28, 2009 11:06 AM

La page charge ...

Honeywell HVC0001/U Mode d'emploi

Ce manuel convient également à

Honeywell HVC0001/U Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents