Honeywell AlarmNet CELL-ANTHB Guide d'installation

Taper
Guide d'installation
AlarmNet CELL-ANTHB
Antenna Kit
Installation and Setup Guide
GENERAL INFORMATION
The antenna included with CELL-ANTHB supports all frequency bands for LTE, 4G, 3G, and CDMA in North America and is
compatible with all cellular communicators used with VISTA and LYNX PLUS controls.
NOTE: This antenna is for indoor use only.
ASSEMBLY
To assemble, refer to the figure below and perform the following steps:
NOTE: Refer to the communication module's Installation and Setup Guide for mounting, wiring and
programming information.
1. Remove the front cover from the communications module.
2. Install the through-hole connector of the adapter cable in the top hole on the enclosure back of the
communications module. Secure with lock washer and nut.
3. Snap the other end of the adapter cable in the external antenna port of the communications module.
4. Attach the antenna to the connector on top of the housing. Replace the front cover.
Antenna Cable Removal Tool
1. Slip the Antenna Cable Removal Tool (p/n 700-03513) under RF Cable
connector as shown.
PLEASE: (1) DO NOT use the tool to pry the connector loose. Instead,
pull directly upward, perpendicular to the circuit board.
Do not pull on
the cable. (2) USE CAUTION not to damage the adjacent components
when inserting the Antenna Cable Removal Tool.
2. Pull directly upwards until the connector detaches from the module’s
receptacle as shown in Detail A. (This cable is no longer needed.)
3. Repeat step 1 and 2 to disconnect the cable from the communication
module. (This cable is no longer needed.)
Cellular Communication Module
SPECIFICATIONS
Antenna
Adapter Cable
Type External Broadband, blade
type with SMA connector,
knuckle and swivel.
VSWR <2.5:1
SMA female /
u.FL (CELL-EXT)
Bands
690-960MHz,
1710-2200MHz,
2500-2700MHz.
LTE Bands 2, 4, 5, 7, 8,
12, 13,14,17, 25, 26
Dimensions 218 x 27 x 13mm
Polarization
Vertical
Polyolefin, black
Gain (Average)
3dBi
50 Ohms
Input Power
(Max.)
10W Connector Type SMA male
RF EXPOSURE
Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures.
Mise en Garde
Exposition aux Fréquences Radio : La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm
(7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les
procédures de produit multi transmetteur FCC et ISED.
IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS
If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer.
TO THE INSTALLER
For the communication module, the external antenna must not exceed a maximum directional gain (including cable loss) as stated on the
FCC Grant of the integrated module.
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.
SUPPORT & WARRANTY INFORMATION
For the latest documentation and support, please go to:
www.resideo.com
For the latest warranty information, please go to:
www.security.honeywellhome.com/warranty
The Honeywell Home Trademark is used under license from Honeywell International Inc.
This product manufactured by Resideo Technologies, Inc. and its affiliates
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2020 Resideo Technologies, Inc.
www.resideo.com
Ê800-20801V1BiŠ
800-20801V1B 4/18 Rev B
  • Page 1 1
  • Page 2 2

Honeywell AlarmNet CELL-ANTHB Guide d'installation

Taper
Guide d'installation

dans d''autres langues