STIEBEL ELTRON DCE-C 6-12 Trend Operation Instruction

OPERATION AND INSTALLATION

UTILISATION ET INSTALLATION

OPERACIÓN E INSTALACIÓN

KEZELÉS ÉS TELEPÍTÉS

RUKOVANJE I INSTALACIJA

ΧΕΙΡΙΣΜΌΣ ΚΑΙ ΕΓΚΑΤΑΣΤΑΣΗ

ЭКСПЛУАТАЦИЯ И УСТАНОВКА



Electronically controlled compact instantaneous water heater | Chauffe-eau

instantané compact à gestion électronique | Calentador instantáneo electrónico

compacto |              

 Ηλεκτρονικά ελεγχόενο κόπακτ στιγιαίο

θεραντήρα ροή |       |











» DCE-C 6/8 Trend

» DCE-C 10/12 Trend

2 | DCE-C Trend www.stiebel-eltron.com

CONTENTS

SPECIAL INFORMATION

OPERATION

1. General information ��3

1.1 Safety instructions �� 3

1.2 Other symbols in this documentation �� 3

1.3 Units of measurement �� 4

2. Safety �� 4

2.1 Intended use �� 4

2.2 General safety instructions �� 4

2.3 Test symbols �� 4

3. Appliance description ��4

4. Cleaning, care and maintenance ��5

5. Troubleshooting ��5

INSTALLATION

6. Safety �� 5

6.1 General safety instructions �� 5

6.2 Shower operation�� 5

6.3 Instructions, standards and regulations �� 5

7. Appliance description ��6

7.1 Standard delivery �� 6

7.2 Accessories �� 6

8. Preparation ��6

8.1 Installation site �� 6

8.2 Minimum clearances �� 6

8.3 Water installation �� 6

9. Installation ��7

9.1 Standard installation on ﬁnished walls �� 7

10. Commissioning ��8

10.1 Changing the connected load via the jumper slot �� 8

10.2 Initial start-up �� 8

10.3 Recommissioning �� 9

11. Appliance shutdown ��9

12. Alternative installation methods ��9

12.1 Electrical connection from above on unﬁnished walls �� 9

12.2 Electrical connection from below on unﬁnished walls �� 10

12.3 Electrical connection with short power cable �� 10

12.4 Electrical connection from the side on ﬁnished walls �� 10

12.5 Water installation on unﬁnished walls �� 10

12.6 Operation with preheated water �� 11

13. Service information �� 12

14. Troubleshooting �� 12

15. Maintenance �� 13

15.1 Draining the appliance �� 13

15.2 Cleaning the strainer ��13

16. Speciﬁcation �� 14

16.1 Dimensions and connections �� 14

16.2 Wiring diagram �� 14

16.3 DHW output �� 14

16.4 Application areas/ conversion table �� 15

16.5 Pressure drop �� 15

16.6 Fault conditions �� 15

16.7 Energy consumption data �� 15

16.8 Data table �� 16

GUARANTEE

ENVIRONMENT AND RECYCLING

ENGLISH

www.stiebel-eltron.com DCE-C Trend | 3

SPECIAL INFORMATION | OPERATION

General information

SPECIAL INFORMATION

- The appliance may be used by children aged3

and older and persons with reduced physical,

sensory or mental capabilities or a lack of ex-

perience and know-how, provided that they

are supervised or they have been instructed

on how to use the appliance safely and have

understood the potential risks. Children must

never play with the appliance. Cleaning and

user maintenance must not be carried out by

children without supervision.

- During operation, the tap can reach tempera-

tures up to 70°C. There is a risk of scalding at

outlet temperatures in excess of 43°C.

- The appliance is suitable for supplying a

shower (shower operation). When using pre-

heated water, ensure that the inlet tempera-

ture does not exceed 55°C.

- Ensure the appliance can be separated from

the power supply by an isolator that discon-

nects all poles with at least 3mm contact

separation.

- The speciﬁed voltage must match the power

supply.

- The appliance must be connected to the earth

conductor.

- The appliance must be permanently connect-

ed to ﬁxed wiring.

- Secure the appliance as described in chapter

"Installation/ Installation".

- Observe the application limits (see chapter

"Installation/ Speciﬁcation/ Data table").

- The speciﬁc water resistivity of the mains

water supply must not be undershot (see

chapter "Installation/ Speciﬁcation/ Data

table").

- Drain the appliance as described in chapter

"Installation/ Maintenance/ Draining the

appliance".

OPERATION

1. General information

The chapters "Special information" and "Operation" are intended

for both users and qualiﬁed contractors.

The chapter "Installation" is intended for qualiﬁed contractors.

Note

Read these instructions carefully before using the appli-

ance and retain them for future reference.

Pass on the instructions to a new user if required.

1.1 Safety instructions

1.1.1 Structure of safety instructions

!

KEYWORD Type of risk

Here, possible consequences are listed that may result

from failure to observe the safety instructions.

f Steps to prevent the risk are listed.

1.1.2 Symbols, type of risk

Symbol Type of risk

Injury

Electrocution

Burns

(burns, scalding)

1.1.3 Keywords

KEYWORD Meaning

DANGER Failure to observe this information will result in serious

injury or death.

WARNING Failure to observe this information may result in serious

injury or death.

CAUTION Failure to observe this information may result in non-seri-

ous or minor injury.

1.2 Other symbols in this documentation

Note

General information is identiﬁed by the adjacent symbol.

f Read these texts carefully.

Symbol Meaning

Material losses

(appliance damage, consequential losses and environmen-

tal pollution)

Appliance disposal

!

OPERATION

Safety

4 | DCE-C Trend www.stiebel-eltron.com

f This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.3 Units of measurement

Note

All measurements are given in millimetres unless oth-

erwise stated.

2. Safety

2.1 Intended use

This appliance is suitable for heating domestic hot water or for

reheating preheated water. The appliance can supply one or more

draw-off points.

Water will not be reheated if the maximum inlet temperature for

reheating is exceeded.

The appliance is intended for domestic use. It can be used safely

by untrained persons. The appliance can also be used in non-do-

mestic environments, e.g. in small businesses, as long as it is

used in the same way.

Any other use beyond that described shall be deemed inappro-

priate. Observation of these instructions and of the instructions

for any accessories used is also part of the correct use of this

appliance.

2.2 General safety instructions

CAUTION Burns

During operation, the tap can reach temperatures up

to 70°C.

There is a risk of scalding at outlet temperatures in ex-

cess of 43°C.

CAUTION Burns

When operating with preheated water, for example

when using a solar thermal system, ensure that the inlet

temperature does not exceed 55°C.

f Limit the inlet temperature with an upstream cen-

tral thermostatic valve.

!

WARNING Injury

The appliance may be used by children aged3 and older

and persons with reduced physical, sensory or mental

capabilities or a lack of experience and know-how, pro-

vided that they are supervised or they have been in-

structed on how to use the appliance safely and have

understood the potential risks. Children must never play

with the appliance. Cleaning and user maintenance must

not be carried out by children without supervision.

!

Material losses

The user should protect the appliance and its tap against

frost.

Note

In order to comply with protection rating IP25, coun-

tersunk screws must be used to secure the appliance to

the wall.

2.3 Test symbols

See type plate on the appliance.

3. Appliance description

The appliance switches on automatically as soon as you open the

hot water valve on the tap. When you close the tap, the appliance

switches off again automatically.

The appliance heats water as it ﬂows through it. The DHW outlet

temperature is set to a ﬁxed value. This is max. 55°C, which can

be reduced by mixing in cold water at the tap.

Upwards of a certain ﬂow rate, the control unit selects the required

heating output, subject to the cold water temperature.

The electronically controlled compact instantaneous water heat-

er with automatic output matching maintains a consistent outlet

temperature. It does so irrespective of the inlet temperature, up

to the maximum output of the appliance.

Heating system

The bare wire heating system is enclosed within a pressure-tested

plastic jacket. The heating system with its stainless steel heater

spiral is suitable for hard and soft water areas and is largely in-

susceptible to scale build-up. The heating system ensures rapid

and efﬁcient DHW provision.

Note

The appliance is equipped with an air detector that large-

ly prevents damage to the heating system. If, during op-

eration, air is drawn into the appliance, the appliance

shuts down heating operation for one minute to protect

the heating system.

Following an interruption to the water supply

!

Material losses

To ensure that the bare wire heating system is not dam-

aged following an interruption to the water supply, the

appliance must be restarted by taking the following steps.

f Disconnect the appliance from the power supply by

removing the fuses/tripping the MCBs.

f Vent the appliance and the cold water inlet line (see

chapter “Installation/ Commissioning/ Initial start-

up”).

f Switch the power back ON.

ENGLISH

www.stiebel-eltron.com DCE-C Trend | 5

OPERATION | INSTALLATION

Cleaning, care and maintenance

Recommended settings

Your instantaneous water heater offers maximum precision and

maximum convenience in DHW provision. If you do nonetheless

operate the appliance with a thermostatic valve, we recommend

adjusting the required set temperature on the thermostatic valve.

4. Cleaning, care and maintenance

f Never use abrasive or corrosive cleaning agents. A damp

cloth is sufﬁcient for cleaning the appliance.

f Check the taps regularly. Limescale deposits at the tap out-

lets can be removed using commercially available descaling

agents.

5. Troubleshooting

Problem Cause Remedy

The appliance will not

start despite the DHW

valve being fully open.

There is no power.

Check the fuses/ MCBs in

your fuse box/ distribu-

tion board.

The aerator in the tap

or the shower head is

scaled up or dirty.

Clean and/or descale the

aerator or shower head.

The water supply has

been interrupted.

Vent the appliance and

the cold water inlet line

(see chapter "Installa-

tion/ Commissioning/

Initial start-up").

When hot water is being

drawn off, cold water

flows for a short period.

The air sensor is detect-

ing air in the water. It

briefly switches off the

heating output.

The appliance restarts

automatically after

1minute.

Boiling noises are heard

during operation.

The appliance is not

vented.

Vent the appliance (see

chapter "Installation/

Commissioning/ Initial

start-up").

The supply pressure is

too low.

Ensure that the mini-

mum supply pressure is

achieved (see chapter

"Installation/ Specifica-

tion/ Data table").

If you cannot remedy the fault, contact your qualiﬁed contractor.

To facilitate and speed up your enquiry, please provide the serial

number from the type plate (000000-0000-000000).

Nr.: 000000-0000-00000

D0000073621

INSTALLATION

6. Safety

Only a qualiﬁed contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

6.1 General safety instructions

We guarantee trouble-free function and operational reliability only

if original accessories and spare parts intended for the appliance

are used.

!

Material losses

Observe the maximum inlet temperature. Higher tem-

peratures may damage the appliance. You can limit the

maximum inlet temperature by installing a central ther-

mostatic valve.

WARNING Electrocution

This appliance contains capacitors which are discharged

when disconnected from the power supply. The capacitor

discharge voltage may brieﬂy exceed60VDC.

6.2 Shower operation

CAUTION Burns

When operating with preheated water, for example

when using a solar thermal system, ensure that the inlet

temperature does not exceed 55°C.

f Limit the inlet temperature with an upstream cen-

tral thermostatic valve.

6.3 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

- The protection rating IP25 (hoseproof) is only guaranteed

with a properly ﬁtted cable grommet and the use of counter-

sunk screws Ø4.5mm with a max. head diameter of 9mm.

- The electrical resistivity of the water must not fall below that

stated on the type plate. In a linked water network, take into

consideration the lowest electrical resistivity of the water.

Your water supply utility will advise you of the electrical re-

sistivity or conductivity of the water in your area.

INSTALLATION

Appliance description

6 | DCE-C Trend www.stiebel-eltron.com

7. Appliance description

7.1 Standard delivery

The following are delivered with the appliance:

- 2 x 45° twin connectors

- 2 ﬂat gaskets

- 2 O-rings

- Cable grommet

- Strainer

- Flow limiter

- Jumper for output changeover, attached

7.2 Accessories

Installation kit for water installation on unﬁnished walls

(200016 - UP-Kit EU)

The installation kit for water installation on unﬁnished walls con-

tains:

- 2 x grommets to seal the apertures in the appliance back

panel

- Strainer with sealed edge for installation on the 45°twin

connector

- Flat gasket

8. Preparation

8.1 Installation site

!

Material losses

Install the appliance in a room that is free from the risk

of frost.

f Always install the appliance vertically and near the draw-off

point.

The appliance is suitable for undersink and oversink installation.

Undersink installation

D0000073616

1

2

1 Cold water inlet

2 DHW outlet

Oversink installation

12

D0000073617

1 Cold water inlet

2 DHW outlet

Note

f Install the appliance ﬂush to the wall. The wall must

have sufﬁcient load bearing capacity.

8.2 Minimum clearances

≥50≥50

≥50

≥100

D0000079442

f Maintain the minimum clearances to ensure trouble-free op-

eration of the appliance and facilitate maintenance work.

8.3 Water installation

!

Material losses

Carry out all water connection and installation work in

accordance with regulations.

f Flush the water line thoroughly.

Taps

Use appropriate pressure taps. Open vented taps are not per-

missible.

Permissible water line materials

- Cold water inlet line:

Pipes made from galvanised steel, stainless steel, copper or

plastic

- DHW outlet line:

Pipes made from stainless steel, copper or plastic

!

Material losses

If plastic pipework systems are used, take into account

the maximum inlet temperature and the maximum per-

missible pressure.

INSTALLATION

Installation

ENGLISH

www.stiebel-eltron.com DCE-C Trend | 7

Flow rate

f Ensure that the ﬂow rate for switching on the appliance is

achieved.

f If the required ﬂow rate is not achieved when the draw-off

valve is fully open, remove the ﬂow limiter from the cold

water inlet.

If required, the pressure in the water installation can also be

raised.

9. Installation

Factory settings 

Trend



Trend

Connected load in kW @ 220V 8.0 12.0

@ 230V 8.7 13.1

Standard installation 

Trend



Trend

Electrical connection from below, installa-

tion on finished walls

x x

Water connection, installation on finished

walls

x x

For further installation options, see chapter "Alternative instal-

lation methods".

9.1 Standard installation on ﬁnished walls

Opening the appliance

D0000073641

f Open the appliance by undoing the screw and lifting up the

appliance cover.

Preparing the power cable

B

A

D0000077179

f Prepare the power cable.

Position on finished walls Dimension A Dimension B

Bottom, centre 30 120

Bottom, left side of appliance 20 90

Bottom, right side of appliance 20 90

Top, right side of appliance 20 80

Position on unfinished walls Dimension A Dimension B

Bottom 20 90

Top 20 80

Preparation

D0000077976

4

3

2

1

57 6

1 Strainer

2 Flow limiter

3 O-rings

4 45° twin connector

5 Flat gaskets

6 Cable grommet

7 Locking screws

f Undo the locking screws.

D0000085450

f Push/break out the required apertures where marked on the

appliance back panel for the power cable and twin connec-

tors. Use a suitable ﬂat tool when doing so. Deburr any sharp

edges with a ﬁle.

f Remove the transport protection plugs from the water con-

nection pipes.

f Cut a hole in the cable grommet to ﬁt the selected connecting

cable. Fit the cable grommet.

f Fit the O-rings into the groove on the twin connectors.

f Push the twin connectors into the apertures in the appliance

back panel and ﬁt them to the appliance connection pipes

using ﬂat gaskets (torque 8Nm).

f Secure the twin connectors with the locking screws.

f Insert the ﬂow limiter and strainer in the twin connector of

the cold water connection. Note the orientation of the ﬂow

limiter.

INSTALLATION

Commissioning

 | DCE-C Trend www.stiebel-eltron.com

Installing the appliance

f Push/break out the lower slots (175mm apart) in the back

panel for securing the appliance (for positions, see chapter

"Speciﬁcation/ Dimensions and connections"). The upper two

ﬁxing holes are already open.

f Mark out the 4drilling positions with reference to the appli-

ance back panel.

f Drill the holes and secure the appliance using suitable ﬁxing

materials (screws and rawl plugs are not part of the standard

delivery): Countersunk screw, Ø4.5mm, max. diameter of

screw-head 9mm.

D0000073844

f Fit a suitable pressure tap.

f Fit the tap pipes to the twin connectors with ﬂat gaskets.

f Open the shut-off valve in the cold water inlet line.

Making the electrical connection

WARNING Electrocution

Carry out all electrical connection and installation work

in accordance with relevant regulations.

WARNING Electrocution

The connection to the power supply is only permissible

as a permanent connection in conjunction with the re-

movable cable grommet. Ensure the appliance can be

separated from the power supply by an isolator that dis-

connects all poles with at least 3mm contact separation.

WARNING Electrocution

Ensure that the appliance is earthed.

!

Material losses

Observe the type plate. The speciﬁed rated voltage must

match the mains voltage.

f Push the power cable through the cable grommet.

f Connect the power cable to the mains terminal (see chapter

"Installation/ Speciﬁcation/ Wiring diagram").

10. Commissioning

10.1 Changing the connected load via the jumper

slot

If you select a connected load other than the factory setting for

the appliance, you will need to reposition the jumper.

1

2

D0000082938

f Install the jumper in the required position on the "Pmax" pin

strip.

Jumper position Connected load

 

1 [low] @ 220V 6.0kW 10.0kW

@ 230V 6.6kW 11.0kW

2 [high]

@ 220V 8.0kW 12.0kW

Factory setting @ 230V 8.7kW 13.1kW

No jumper [low]

@ 220V 6.0kW 10.0kW

@ 230V 6.6kW 11.0kW

10.2 Initial start-up

f Tick the selected connected load on the type plate. Use a

ballpoint pen to do this.

≥ 3 min.

on

15 x

off

D0000101520

f Open and close all connected draw-off valves 15 times

over a period of at least 3 minutes, until all air has been

purged from the pipework and the appliance. Vent the cold

water inlet line and the appliance using a ﬂow rate of least

3.5l/min.

f Carry out a tightness check.

D0000073622

f Activate the safety switch by ﬁrmly pressing the reset button

(the appliance is delivered with the safety switch disabled).

INSTALLATION

Appliance shutdown

ENGLISH

www.stiebel-eltron.com DCE-C Trend | 9

D0000073642

f Hook the appliance cover into the appliance back panel at the

top rear. Pivot the appliance cover downwards. Check that

the appliance cover is securely seated both top and bottom.

f Secure the appliance cover with the screw.

D0000053281

f Switch on the power supply.

10.2.1 Appliance handover

f Explain the appliance function to users and familiarise them

with how it works.

f Make the user aware of potential dangers, especially the risk

of scalding.

f Hand over the instructions.

10.3 Recommissioning

!

Material losses

To ensure that the bare wire heating system is not dam-

aged following an interruption to the water supply, the

appliance must be restarted by taking the following steps.

f Disconnect the appliance from the power supply by

removing the fuses/tripping the MCBs.

f Vent the appliance and the cold water inlet line (see

chapter "Commissioning/ Initial start-up").

f Switch the power back ON.

11. Appliance shutdown

f Isolate all poles of the appliance from the power supply.

f Drain the appliance (see chapter "Maintenance/ Draining the

appliance").

12. Alternative installation methods

WARNING Electrocution

Before performing any work on the appliance, discon-

nect all poles from the power supply.

12.1 Electrical connection from above on unﬁnished

walls

D0000073620

2

1

1 Cable grommet

2 Cable routing

f Break out the required aperture in the back panel for the

power cable (for positions, see chapter "Speciﬁcation/ Di-

mensions and connections"). Deburr any sharp edges with a

ﬁle.

f Cut a hole in the cable grommet to ﬁt the selected connecting

cable. Fit the cable grommet.

f Reposition the mains terminal from the bottom to the top.

To do so, unclip the mains terminal by pushing it ﬁrmly to

the left and pulling it forwards. Turn the mains terminal with

connecting cables 180° clockwise. Lay the internal wiring

under the cable guide. Clip the mains terminal in by pushing

it inwards and to the left until it clicks into place.

f Install the appliance and connect the power cable to the

mains terminal as described in chapter "Installation/ Stand-

ard installation on ﬁnished walls".

Note

Disconnecting the mains terminal at the top:

f Use a screwdriver to disengage the locking tab from

the right-hand side.

INSTALLATION

Alternative installation methods

10 | DCE-C Trend www.stiebel-eltron.com

12.2 Electrical connection from below on unﬁnished

walls

D0000079465

1

1 Cable grommet

f Break out the required aperture in the back panel for the

power cable (for positions, see chapter "Speciﬁcation/ Di-

mensions and connections"). Deburr any sharp edges with a

ﬁle.

f Cut a hole in the cable grommet to ﬁt the selected connecting

cable. Fit the cable grommet.

f Install the appliance and connect the power cable to the

mains terminal as described in chapter "Installation/ Stand-

ard installation on ﬁnished walls".

12.3 Electrical connection with short power cable

If the power cable is not quite long enough, you can install the

mains terminal in the appliance a little closer to the aperture.

D0000073648

1

1 Cable grommet

f Reposition the mains terminal from the top to the bottom. To

do so, unclip the mains terminal by pushing it ﬁrmly to the

left and pulling it forwards. Clip the mains terminal in at the

bottom by pushing it inwards and to the left until it clicks

into place.

12.4 Electrical connection from the side on ﬁnished

walls

f Cut and break out the required aperture in the appliance

back panel and appliance cover for the power cable (for po-

sitions, see chapter "Speciﬁcation/ Dimensions and connec-

tions"). Deburr any sharp edges with a ﬁle.

f Install the appliance and connect the power cable to the

mains terminal as described in chapter "Installation/ Stand-

ard installation on ﬁnished walls".

12.5 Water installation on unﬁnished walls

You will need the appropriate accessories to carry out the in-

stallation. The installation kit for water installation on unﬁnished

walls contains:

- 2 x grommets to seal the apertures in the appliance back

panel

- Strainer with sealed edge for installation on the 45°twin

connector

- Flat gasket

In addition, you will need the ﬂow limiter included in the appliance

standard delivery.

Preparation

44-46

D0000073660

f Insert and seal the 45°twin connectors.

To break out the apertures in the appliance back panel, you will

need to remove the function module from the back panel.

1.

4.

5.

2.

3.

D0000077971

f Undo the screw and disengage the locking tab.

f Push the function module on the back panel gently

backwards.

f Remove the function module from the appliance back panel

by pulling it slightly forwards and lifting it off.

f Push/break out the required apertures for the water connec-

tions in the back panel from behind (for positions, see chap-

ter "Speciﬁcation/ Dimensions and connections"). Deburr any

sharp edges with a ﬁle.

INSTALLATION

Alternative installation methods

ENGLISH

www.stiebel-eltron.com DCE-C Trend | 11

1.

2.

3.

4.

D0000077974

1 2 3

4

5

1 Flow limiter

2 O-ring

3 Cold water pipe bend with recess for spring clip

4 Spring clip

5 Heater

f Remove the cold water pipe bend and the O-ring.

f Insert the ﬂow limiter (part of the appliance standard

delivery) in the cold water inlet of the heater. Note the

orientation.

f Fit the cold water pipe bend with the O-ring.

!

Material losses

The O-ring must be ﬁtted to prevent the appliance from

leaking.

f As part of installation, check that the O-ring is in

place.

f Secure the cold water pipe bend with the spring clip.

!

Material losses

Ensure that the spring clip is located behind the recess

in the pipe bend and that it is securely holding the pipe

bend in place.

f Fit the function module on the appliance back panel in re-

verse order until it clicks into place.

f Secure the function module with the screw.

Installing the appliance

D0000073842

321

1 Grommets

2 Flat gasket

3 Strainer with sealed edge

f Mark out the 2drilling positions in the upper section of the

appliance back panel with reference to the appliance back

panel.

f Fit the grommets in the appliance back panel from the front.

f Drill the holes and secure the appliance using suitable ﬁxing

materials (screws and rawl plugs are not part of the standard

delivery): Countersunk screw, Ø4.5mm, max. diameter of

screw-head 9mm.

Note

f Install the appliance ﬂush to the wall. If necessary,

additionally secure the appliance at the 2 lower

attachment points. To do this, push/break out the

lower slots (175mm apart) in the appliance back

panel (for positions, see chapter "Speciﬁcation/ Di-

mensions and connections").

f Remove the transport protection plugs from the water con-

nection pipes.

f Secure the DHW connection pipe with a ﬂat gasket and the

cold water inlet line with the sealed-edge strainer (from the

accessories) to the twin connectors.

12.6 Operation with preheated water

You can limit the maximum inlet temperature by installing a cen-

tral thermostatic valve.

INSTALLATION

Service information

12 | DCE-C Trend www.stiebel-eltron.com

13. Service information

Connection overview/ component overview

D0000082950

1

2

3

4

1 Flow meter

2 High limit safety cut-out, automatic reset

3 Pin strip for connected load

4 Diagnostic trafﬁc lights

14. Troubleshooting

WARNING Electrocution

To test the appliance, it must be connected to the power

supply.

Note

When testing the appliance using the diagnostic trafﬁc

lights, water must be ﬂowing.

Signals of the diagnostic traffic lights (LED)

Red Lights up in the event of a fault

Yellow Lights up in heating mode/flashes when output limit

reached

Green Flashing: Appliance connected to power supply

Diagnostic traffic

lights (draw-off

mode)

Fault Cause Remedy

No LED illuminates Appliance does not heat up

One or more power supply phases are missing Check the fuses in the distribution board

PCB faulty Replace the function module

Green flashing,

yellow off, red off

No DHW

Appliance starting flow rate not reached; shower

head/aerator scaled up

Descale/replace the shower head/aerator

Appliance starting flow rate not reached; strainer in

cold water inlet dirty

Cleaning the strainer

Flow meter not plugged in Check plug-in connection; correct if necessary

Flow meter faulty or dirty Replace the function module

PCB faulty Replace the function module

Green flashing,

yellow on, red off

No DHW; outlet temperature

does not match set value

Tap faulty Replace tap

Heating system faulty Replace the function module

PCB faulty Replace the function module

Green flashing,

yellow off, red on

No DHW; outlet temperature

does not match set value

Air detection has responded Continue draw-off for >1min

Safety switch not activated during "Commissioning" Activate the safety switch by firmly pressing the reset

button

Safety switch was triggered by high limit safety cut-

out

Check high limit safety cut-out (plug-in connection,

connecting cable); activate safety switch

Safety switch responds again after high limit safety

cut-out has been checked; high limit safety cut-out

faulty

Replace high limit safety cut-out; activate safety

switch and draw-off with maximum set value >1min

Safety switch responds again; PCB faulty Replace the function module

PCB faulty Replace the function module

INSTALLATION

Maintenance

ENGLISH

www.stiebel-eltron.com DCE-C Trend | 13

15. Maintenance

WARNING Electrocution

Before performing any work on the appliance, discon-

nect all poles from the power supply.

This appliance contains capacitors which are discharged

when disconnected from the power supply. The capacitor

discharge voltage may brieﬂy exceed60VDC.

15.1 Draining the appliance

The appliance can be drained for maintenance work.

WARNING Burns

Hot water may escape when you drain the appliance.

f Close the shut-off valve in the cold water inlet line.

f Open all draw-off valves.

f Undo the water connections on the appliance.

f Store the dismantled appliance free from the risk of frost, as

water residues remaining inside the appliance can freeze and

cause damage.

15.2 Cleaning the strainer

WARNING Burns

Hot water may escape when you drain the appliance.

!

Material losses

To ensure that the bare wire heating system is not dam-

aged following an interruption to the water supply, the

appliance must be recommissioned by taking the follow-

ing steps.

f Disconnect the appliance from the power supply by

removing the fuses/tripping the MCBs.

f Vent the appliance and the cold water inlet line (see

chapter "Commissioning/ Initial start-up").

f Switch on the power supply again.

The strainer in the cold water threaded ﬁtting must be cleaned

regularly.

15.2.1 Cleaning the strainer, standard installation on ﬁnished

walls

f Isolate the appliance from the power supply.

f Close the shut-off valve in the cold water inlet line.

f Open all draw-off valves.

f Remove the cold water threaded ﬁtting.

f Remove the strainer from the twin nipple using a ﬂat-blade

screwdriver. Clean the strainer.

f Reinsert the strainer. Screw the cold water connection pipe

onto the twin nipple.

f Open the shut-off valve in the cold water inlet line.

f Vent the appliance and the cold water inlet line (see chapter

"Commissioning/ Initial start-up").

f Switch on the power supply.

15.2.2 Cleaning the strainer, installation on unﬁnished walls

f Isolate the appliance from the power supply.

f Close the shut-off valve in the cold water inlet line.

f Open all draw-off valves.

f Open the appliance by undoing the screw and lifting up the

appliance cover.

f Unscrew the cold water connection pipe from the twin nip-

ple. Pivot the cold water connection pipe upwards.

f Remove the strainer from the twin nipple. Clean the strainer.

f Screw the cold water connection pipe and the strainer with

sealed edge onto the twin nipple.

f Open the shut-off valve in the cold water inlet line.

f Vent the appliance and the cold water inlet line (see chapter

"Commissioning/ Initial start-up").

f Check the cold water connection for leaks.

f Hook the appliance cover into the appliance back panel at the

top rear. Pivot the appliance cover downwards. Check that

the appliance cover is securely seated both top and bottom.

Secure the appliance cover with the screw.

f Switch on the power supply.

INSTALLATION



14 | DCE-C Trend www.stiebel-eltron.com

16. Speciﬁcation

16.1 Dimensions and connections

372

358

343

14

97

217

140

175

100

c01c06

35

32

b02

380

D0000084885

DCE-C Trend

b02 Entry for electrical cables I Finished walls

c01 Cold water inlet Male thread G 1/2 A

c06 DHW outlet Male thread G 1/2 A

Alternative connection options

100

c01c06

b02

72

330

b02

69

35

336

b02

b03

30

61

15

b03

D0000073720

DCE-C Trend

b02 Entry for electrical cables I Finished walls

b03 Entry for electrical cables II Unfinished walls

c01 Cold water inlet Male thread G 1/2 A

c06 DHW outlet Male thread G 1/2 A

16.2 Wiring diagram

DCE-C Trend

L L

2/GRD ~ 220 / 230V

L N

1/N/PE ~ 220 / 230V

N

L

D0000077991

1

3

4

2

1 Power PCB with integral safety switch

2 Bare wire heating system

3 High limit safety cut-out

4 Mains terminal

16.3 DHW output

The DHW output is subject to the connected power supply, the

appliance's connected load and the cold water inlet temperature.

The rated voltage and rated output can be found on the type plate.

Connected load in kW 

Rated voltage Cold water inlet temperature

     

DCE-C 6/8 Trend

6.0 2.6 3.1 3.7 4.8

8.0 3.5 4.1 5.0 6.3

6.6 2.9 3.4 4.1 5.2

8.7 3.8 4.4 5.4 6.9

DCE-C 10/12 Trend

10.0 4.3 5.1 6.2 7.9

12.0 5.2 6.1 7.5 9.5

11.0 4.8 5.6 6.8 8.7

13.1 5.7 6.7 8.1 10.4

Connected load in kW 

Rated voltage Cold water inlet temperature

     

DCE-C 6/8 Trend

6.0 1.9 2.1 2.4 2.9

8.0 2.5 2.9 3.3 3.8

6.6 2.1 2.4 2.7 3.1

8.7 2.8 3.1 3.6 4.1

DCE-C 10/12 Trend

10.0 3.2 3.6 4.1 4.8

12.0 3.8 4.3 4.9 5.7

11.0 3.5 3.9 4.5 5.2

13.1 4.2 4.7 5.3 6.2

INSTALLATION



ENGLISH

www.stiebel-eltron.com DCE-C Trend | 15

16.4 Application areas/ conversion table

Electrical resistivity and electrical conductivity.

Standard specifica-







Resis-

tivity

ρ≥

Conductivity ≤

Resis-

tivity

ρ≥

Conductivity ≤

Resis-

tivity

ρ≥

Conductivity ≤

Ωcm mS/m μS/cm Ωcm mS/m μS/cm Ωcm mS/m μS/cm

1100 91 910 970 103 1031 895 112 1117

16.5 Pressure drop

Taps



Mono lever mixer tap, approx. MPa 0.04 - 0.08

Thermostatic valve, approx. MPa 0.03 - 0.05

Shower head, approx. MPa 0.03 - 0.15

Sizing the pipework

When calculating the size of the pipework, an appliance pressure

drop of 0.1MPa is recommended.

16.6 Fault conditions

In the event of a fault, loads up to 80°C at a pressure of 1.0MPa

can occur brieﬂy in the installation.

16.7 Energy consumption data

Product datasheet: Conventional water heaters to regulation (EU) no. 812/2013 | 814/2013

 

238148 238149

Manufacturer STIEBEL ELTRON STIEBEL ELTRON

Load profile XS XS

Energy efficiency class A A

Energy conversion efficiency % 39 39

Annual power consumption kWh 472 472

Default temperature setting °C 55 55

Sound power level dB(A) 15 15

Special information on measuring efficiency Measured with integral flow limiter and

maximum output

Measured with integral flow limiter and

maximum output

Daily power consumption kWh 2.161 2.163

16 | DCE-C Trend www.stiebel-eltron.com





16.8 Data table

 

238148 238149

Electrical data

Rated voltage V 220 230 220 230

Rated output kW 6.0/8.0 6.6/8.7 10.0/12.0 11.0/13.1

Rated current A 27.3/36.4 28.5/38.0 45.5/54.5 47.8/57.0

Fuse protection A 30/40 30/40 50/60 50/60

Frequency Hz 50/60 50/60 50/60 50/60

Phases 1/N/PE 1/N/PE

Resistivity ρ15 ≥ Ω cm 1100 1100

Conductivity 15 ≤ μS/cm 910 910

Max. mains impedance at 50Hz Ω 0.0385 0.0368 0.0257 0.0245

Connections

Water connection G 1/2 A G 1/2 A

Application limits

Minimum supply pressure MPa 0.18 (1.8 bar / 26 psi) 0.18 (1.8 bar / 26 psi)

Max. permissible pressure MPa 1 (10 bar / 150 psi) 1 (10 bar / 150 psi)

Max. inlet temperature for reheating °C 55 55

Temperature setting range °C 55 55

Values

Max. inlet temperature (e.g. pasteurisation) °C 70 70

On l/min 1.3 1.3

Flow rate at 28K l/min 3.1/4.1 @ 220V 5.1/6.2 @ 220V

Flow rate at 50K l/min 1.7/2.3 @ 220V 2.9/3.5 @ 220V

Pressure drop for flow rate at 50K (without flow limiter) MPa 0.01/0.01 0.02/0.03

Flow rate limit at l/min 4 5

Hydraulic data

Nominal capacity l 0.277 0.277

Versions

Type of installation Oversink/ undersink Oversink/ undersink

Adjustable connected load X X

Protection class 1 1

Insulating block Plastic Plastic

Heating system heat generator Bare wire Bare wire

Cover and back panel Plastic Plastic

Colour White White

IP rating IP25 IP25

Dimensions

Height mm 372 372

Width mm 217 217

Depth mm 97 97

Weights

Weight kg 2.5 2.5

Note

The appliance conforms to IEC 61000-3-12.

Guarantee

The guarantee conditions of our German companies do not

apply to appliances acquired outside of Germany. In countries

where our subsidiaries sell our products a guarantee can only

be issued by those subsidiaries. Such guarantee is only grant-

ed if the subsidiary has issued its own terms of guarantee. No

other guarantee will be granted.

We shall not provide any guarantee for appliances acquired in

countries where we have no subsidiary to sell our products.

This will not aect warranties issued by any importers.

Environment and recycling

We would ask you to help protect the environment. After use,

dispose of the various materials in accordance with national

regulations.

GUARANTEEGUARANTEE



FRANÇAIS

www.stiebel-eltron.com DCE-C Trend | 17

TABLE DES MATIÈRES

REMARQUES PARTICULIÈRES

UTILISATION

1. Remarques générales �� 18

1.1 Consignes de sécurité �� 18

1.2 Autres pictogrammes utilisés dans cette

documentation �� 19

1.3 Unités de mesure �� 19

2. Sécurité �� 19

2.1 Utilisation conforme �� 19

2.2 Consignes de sécurité générales �� 19

2.3 Label de conformité �� 19

3. Description de l’appareil �� 19

4. Nettoyage, entretien et maintenance �� 20

5. Dépannage �� 20

INSTALLATION

6. Sécurité �� 21

6.1 Consignes de sécurité générales ��21

6.2 Mode douche �� 21

6.3 Prescriptions, normes et réglementations�� 21

7. Description de l’appareil �� 21

7.1 Fourniture �� 21

7.2 Accessoires �� 21

8. Travaux préparatoires �� 21

8.1 Lieu d’installation �� 21

8.2 Distances minimales �� 22

8.3 Installation hydraulique �� 22

9. Montage �� 22

9.1 Montage normal en saillie �� 22

10. Mise en service �� 24

10.1 Modiﬁcation du réglage de puissance raccordée par

déplacement du cavalier ��24

10.2 Première mise en service �� 24

10.3 Remise en marche ��24

11. Mise hors service �� 24

12. Variantes de pose �� 25

12.1 Raccordement électrique par le haut en installation

encastrée �� 25

12.2 Raccordement électrique sous crépi par le bas �� 25

12.3 Raccordement électrique en cas de câble

d’alimentation court �� 25

12.4 Raccordement électrique en saillie sur le côté �� 25

12.5 Installation hydraulique encastrée �� 26

12.6 Fonctionnement avec de l’eau préchauffée �� 27

13. Informations Service �� 27

14. Aide au dépannage �� 28

15. Maintenance �� 28

15.1 Vidange de l’appareil �� 28

15.2 Nettoyer le ﬁltre �� 29

16. Données techniques �� 29

16.1 Cotes et raccordements �� 29

16.2 Schéma électrique �� 30

16.3 Capacité de production d’eau chaude �� 30

16.4 Domaines d’utilisation/ Tableau de conversion �� 30

16.5 Pertes de charge �� 30

16.6 Défaillances �� 30

16.7 Indications relatives à la consommation énergétique �� 30

16.8 Tableau de données �� 31

GARANTIE

PROTECTION DE L’ENVIRONNEMENT ET RECYCLAGE

 | DCE-C Trend www.stiebel-eltron.com

REMARQUES PARTICULIÈRES | UTILISATION

Remarques générales

REMARQUES

PARTICULIÈRES

- L’appareil peut être utilisé par des enfants de

3ans et plus ainsi que par des personnes aux

facultés physiques, sensorielles ou mentales

réduites ou par des personnes sans expé-

rience, s’ils sont accompagnés ou qu’ils ont

appris à l’utiliser en toute sécurité, et s’ils ont

compris les dangers encourus. Ne laissez pas

les enfants jouer avec l’appareil. Ne conﬁez

pas le nettoyage ni les opérations de mainte-

nance réservées aux utilisateurs à des enfants

sans surveillance.

- En fonctionnement, la température de la robi-

netterie peut atteindre 70°C. Risque de brû-

lure à des températures de sortie supérieures

à 43°C.

- Cet appareil convient à l’alimentation d’une

douche (en mode douche). Dans le cas d’une

arrivée d’eau préchauffée, il faut s’assurer

que sa température ne peut pas dépasser

55°C.

- L’appareil doit pouvoir être mis hors tension

par un dispositif de coupure omnipolaire

ayant une ouverture minimale des contacts de

3mm.

- La tension indiquée doit correspondre à la

tension d’alimentation.

- L’appareil doit être raccordé au conducteur de

mise à la terre.

- L’appareil doit être raccordé en permanence à

un câblage ﬁxe.

- Fixez l’appareil comme indiqué dans le cha-

pitre «Installation/ Montage».

- Respectez les limites d’utilisation (voir le cha-

pitre «Installation/ Données techniques/

Tableau de données»).

- La résistance hydraulique spéciﬁque du ré-

seau de distribution d’eau ne doit pas être

dépassée (voir le chapitre «Installation/ Don-

nées techniques/ Tableau de données»).

- Vidangez l’appareil comme indiqué au cha-

pitre «Installation/ Maintenance / Vidange

de l’appareil».

UTILISATION

1. Remarques générales

Les chapitres «Remarquesparticulières» et «Utilisation »

s’adressent aux utilisateurs de l’appareil et aux installateurs.

Le chapitre «Installation» s’adresse aux installateurs.

Remarque

Lisez attentivement cette notice avant l’utilisation et

conservez-la soigneusement.

Le cas échéant, remettez cette notice à tout nouvel uti-

lisateur.

1.1 Consignes de sécurité

1.1.1 Présentation des consignes de sécurité

!

MENTION D’AVERTISSEMENT Nature du danger

Sont indiqués ici les risques éventuellement encourus en

cas de non-respect de la consigne de sécurité.

f Indique les mesures permettant de prévenir le dan-

ger.

1.1.2 Symboles, nature du danger

Symbole Nature du danger

Blessure

Électrocution

Brûlure

(brûlure, ébouillantement)

1.1.3 Mentions d’avertissement

MENTION

-

MENT

Signification

DANGER Caractérise des consignes dont le non-respect entraîne de

graves lésions, voire la mort.

AVERTISSEMENT Caractérise des consignes dont le non-respect peut entraî-

ner de graves lésions, voire la mort.

ATTENTION Caractérise des consignes dont le non-respect peut entraî-

ner des lésions légères ou moyennement graves.

!

UTILISATION

Sécurité

FRANÇAIS

www.stiebel-eltron.com DCE-C Trend | 19

1.2 Autres pictogrammes utilisés dans cette

documentation

Remarque

Le symbole ci-contre caractérise des consignes générales.

f Lisez attentivement les consignes.

Symbole Signification

Dommages matériels

(dommages touchant à l’appareil, dommages indirects et

pollution de l’environnement)

Recyclage de l’appareil

f Ce symbole signale une action à entreprendre. Les actions

nécessaires sont décrites étape par étape.

1.3 Unités de mesure

Remarque

Sauf indication contraire, toutes les cotes sont indiquées

dans l’unité des millimètres.

2. Sécurité

2.1 Utilisation conforme

L’appareil sert au chauffage de l’eau sanitaire ou au chauffage

d’appoint d’une eau préchauffée. L’appareil peut alimenter un ou

plusieurs points de soutirage.

Lorsque la température d’arrivée d’eau maximale pour le chauf-

fage d’appoint est dépassée, ce dernier n’est pas effectué.

L’appareil est conçu pour une utilisation domestique. Il peut être

utilisé sans risque par des personnes qui ne disposent pas de

connaissances techniques particulières. L’appareil peut également

être utilisé dans un environnement non domestique, par exemple

dans de petites entreprises, à condition que son utilisation soit

du même ordre.

Tout autre emploi est considéré comme non conforme. Une uti-

lisation conforme de l’appareil implique également le respect de

cette notice et de celles des accessoires utilisés.

2.2 Consignes de sécurité générales

ATTENTION Brûlure

En fonctionnement, la température de la robinetterie

peut atteindre 70°C.

Risque de brûlure à des températures de sortie supé-

rieures à 43°C.

ATTENTION Brûlure

Pour une utilisation avec de l’eau préchauffée, par ex.

si une installation solaire est utilisée, s’assurer que la

température d’arrivée d’eau ne dépasse pas 55°C.

f Limitez la température d’arrivée d’eau au moyen

d’une robinetterie à soupape thermostatique.

!

AVERTISSEMENT Blessure

L’appareil peut être utilisé par des enfants de 3ans et

plus ainsi que par des personnes aux facultés physiques,

sensorielles ou mentales réduites ou par des personnes

sans expérience, s’ils sont accompagnés ou qu’ils ont

appris à l’utiliser en toute sécurité, et s’ils ont compris

les dangers encourus. Ne laissez pas les enfants jouer

avec l’appareil. Ne conﬁez pas le nettoyage ni les opé-

rations de maintenance réservées aux utilisateurs à des

enfants sans surveillance.

!

Dommages matériels

L’appareil et la robinetterie doivent être protégés du gel

par l’utilisateur.

Remarque

Pour garantir l’indice de protection IP25, il faut utiliser

des vis à tête fraisée pour ﬁxer l’appareil au mur.

2.3 Label de conformité

Voir la plaque signalétique sur l’appareil.

3. Description de l’appareil

L’appareil se met en marche dès que vous ouvrez le robinet d’eau

chaude. Lorsque vous fermez le robinet, l’appareil s’éteint auto-

matiquement.

L’appareil chauffe l’eau pendant qu’elle circule dans l’appareil.

La température de sortie de l’eau chaude sanitaire est déﬁnie sur

une valeur ﬁxe. Elle est de 55°C et peut être diminuée par l’ajout

d’eau froide au niveau de la robinetterie.

À partir d’un certain débit, la régulation se commute sur la puis-

sance de chauffe nécessaire en fonction de la température de

l’eau froide.

Le chauffe-eau instantané compact à commande électronique et

ajustement automatique de la puissance maintient la température

de sortie sur une valeur constante. Et ce, indépendamment de la

température d’arrivée d’eau et jusqu’à la puissance maximale de

l’appareil.

Système de chauffe

Système de chauffe à ﬁl nu enveloppé sous une gaine plastique

résistant à la pression. Très résistant à l’entartrage, ce système

de chauffe avec serpentin en acier inoxydable convient indiffé-

remment à l’eau faiblement et fortement calcaire. Ce système de

chauffe permet une alimentation en eau chaude sanitaire rapide

et efﬁcace.

Remarque

L’appareil est équipé d’un détecteur d’air qui prévient en

grande partie l’endommagement du système de chauffe.

Si de l’air pénètre dans l’appareil en cours de fonction-

nement, la puissance de chauffe est désactivée pendant

une minute de manière à protéger le système de chauffe.

!

UTILISATION

Nettoyage, entretien et maintenance

20 | DCE-C Trend www.stiebel-eltron.com

Après coupure d’eau

!

Dommages matériels

Aﬁn d’éviter une panne du système de chauffe à ﬁl nu

après une coupure d’eau, procédez selon les étapes sui-

vantes pour remettre l’appareil en service.

f Mettez l’appareil hors tension par le fusible ou le

disjoncteur.

f Purgez l’appareil et la conduite d’arrivée d’eau

froide (voir le chapitre «Installation/ Mise en ser-

vice/ Première mise en service»).

f Remettez l’appareil sous tension.

Réglages recommandés

Votre chauffe-eau instantané assure un maximum de précision et

de confort pour la production de l’eau chaude sanitaire. Si toute-

fois, vous utilisez l’appareil avec une robinetterie thermostatique,

nous vous recommandons de régler la température de consigne

souhaitée au niveau de la robinetterie thermostatique.

4. Nettoyage, entretien et

maintenance

f N’utilisez aucun produit de nettoyage abrasif ou corrosif.

Un chiffon humide sufﬁt pour le nettoyage et l’entretien de

l’appareil.

f Contrôlez régulièrement les robinetteries. Vous pouvez éli-

miner le tartre au niveau des becs de robinetterie avec les

produits de détartrage du commerce.

5. Dépannage

Problème Cause Remède

L’appareil ne démarre

pas bien que le robinet

d’eau chaude soit entiè-

rement ouvert.

L’appareil n’est pas sous

tension.

Contrôlez les disjoncteurs

de l’installation domes-

tique.

Le mousseur placé dans

la robinetterie ou la

pomme de douche sont

entartrés ou encrassés.

Nettoyez et/ou détar-

trez le mousseur ou la

pomme de douche.

L’alimentation en eau est

coupée.

Purgez l’appareil et l’ar-

rivée d’eau froide (voir le

chapitre «Installation/

Mise en service/ Pre-

mière mise en service»).

De l’eau froide s’écoule

temporairement pendant

le soutirage d’eau chaude

sanitaire.

Le détecteur d’air trouve

de l’air dans l’eau. Il

coupe brièvement la

puissance de chauffe.

Après 1minute, l’appa-

reil se remet automati-

quement en marche.

Des bruits d’ébullition se

produisent en cours de

fonctionnement.

L’appareil n’est pas

purgé.

Purgez l’appareil (voir le

chapitre «Installation/

Mise en service/ Pre-

mière mise en service»).

La pression d’alimenta-

tion est trop faible.

Assurez-vous que la

pression d’alimentation

minimum est atteinte

(voir le chapitre «Ins-

tallation/ Données

techniques/ Tableau de

données»).

Appelez votre installateur si vous ne réussissez pas à résoudre

le problème. Pour obtenir une aide efﬁcace et rapide, communi-

quez-lui le numéro indiqué sur la plaque signalétique (000000-

0000-000000).

Nr.: 000000-0000-00000

D0000073621

La page est en cours de chargement...

STIEBEL ELTRON DCE-C 6-12 Trend Operation Instruction

STIEBEL ELTRON DCE-C 6-12 Trend Operation Instruction

Documents connexes