Wincor Nixdorf KA16 Cassette Cash Drawer Mode d'emploi

Taper
Mode d'emploi
KA 16
Cassette Cash Drawer
Product Manual
Edition March 2000
BEETLE® is a registered trademark of the Wincor Nixdorf GmbH
Copyright © Wincor Nixdorf GmbH & Co. KG, 2000
The reproduction, transmission or use of this document or its contents is not permitted
without express authority.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design,
are reserved.
Delivery subject to availability; technical modifications possible.
Contents
Manufacturer’s Declaration and Approval..............................................1
FCC-Class A Declaration..........................................................................1
The KA 16 Cassette Cash Drawer............................................................2
General......................................................................................................2
Summary of Features................................................................................3
Setting up the Cash Drawer......................................................................3
Emergency Opening..................................................................................5
Activating the Cassette Cash Drawer .......................................................5
The money compartments........................................................................6
Connection system....................................................................................8
Technical Data...........................................................................................9
Appendix...................................................................................................10
Installation Instructions............................................................................10
Installation ...............................................................................................11
Manufacturers Declaration and Approval
The device complies with the requirements of the EEC
directives 89/336/EEC with regard to Electromagnetic
compatibilityand 73/23/EEC Low Voltage Directive.
Therefore, you will find the CE mark on the device or
packaging.
FCC-Class A Declaration
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interfe-
rence at his own expense.
Le présent appareil numérique ne génère pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la Classe
A prescrites dans le Règlement sur le brouillage radioélectrique édicté
par le ministère des Communications du Canada.
Important Note
First connect the signal cable with the cash drawer.Then connect it to the
host system (BEETLE or printer) !
GB - 1
The KA 16 Cassette Cash Drawer
KA 16 Cassette Cash Drawer
General
The KA 16 Cassette Cash Drawer is a small, space-saving drawer with a
hinged cover, designed as a desktop model.Thanks to its compact con-
struction and upward opening cover, the cash drawer has a very small foot-
print.The hinged covers wide opening angle makes coins and bank notes
easily accessible.The essential components of the cash drawer are the
base plate and the electronic unit it accommodates, the plastic housing,
the coin trays and the electromechanical lock.An extra jack is provided for
connecting a second cash drawer.
KA 16 Cassette Cash Drawer
KA 16 Cassette Cash Drawer
GB - 2
Summary of features
Drawer opens upward
Compact design
Adjustable money compartments
Small footprint
Setting up the cash drawer
Setting up the cash drawer
The base plate must be mounted horizontally in the flat surface of a chek-
kout desk.Please refer to the Appendix for the installation instructions.
Place the cash drawer on the base plate, noting the position of the vertical
guide slots on the electronic unit housing. Then slide back the cash drawer
until it locks into place.It is now firmly attached to the checkout desk and,
for security reasons, can be opened only by means of the POS system.
To release the cash
drawer from the
base plate, open the
drawer by means
of the POS system.
The lock is now
accessible. Unlock
thecashdrawerfrom
the base plate by
rotating the lock
clockwise approx. 10
degrees using, for
example, the plastic
key.
Setting up the cash drawer
GB - 3
A spring mechanism
automatically slides
the drawer about half
an inch forward.
You can now lift the
cash drawer off the
base plate.
When not installed on the base plate, the cash drawer can be opened by
means of the cylinder lock (safe function).
Setting up the cash drawer
GB - 4
Emergency opening
If absolutely necessary, you can release the cash drawer by inserting a
screwdriver in a small opening in the base plate from below.After the cash
drawer is released, it can then be opened by means of the key.
For this feature to be used, there must be an opening in the desktop
through which a tool can be inserted for releasing the cash drawer
(see Appendix).
Make sure beforehand that the emergency opening function is
allowed.
Activating the cassette cash drawer
Activating the cassette cash drawer
For the cash drawer to be put into service, the configuration software must
log it into the POS system. The POS software, controlled by means of the
POS keyboard, opens the cash drawer.
Activating the cassette cash drawer
GB - 5
The money compartments
The moneycompartments
The housing has four
bank note compart-
ments, eight coin
compartments and a
compartment be-
neath the coin com-
partments for
checks, large bank
notes, rolls of coins
and receipts.
The bank note compartments on the left-hand side are adjustable by me-
ans of removeable dividers.These dividers can be installed either vertical-
ly or tilted by 10degrees, thus allowing you to set the depth of the
individual compartments. Spring-loaded pressure plates attached to the di-
viders press the bank notes toward the front so that they are firmly held in
place.
The money compartments
GB - 6
To the right of the
bank note compart-
ments are two coin
trays with four coin
compartments each.
The coin trays are in-
stalled in the cash
drawer one behind
the other. The fact
that the trays are se-
parated means that
only the front tray
need be removed to
access the check
compartment be-
neath it.
The money compartments
GB - 7
Connection system
Connection system
The electronic plug connector (base) is accommodated in a housing atta-
ched the base plate.This unit electronically controls the opening of the
cash drawer.
The cash drawer is connec-
ted to the POS system by
means of connecting cable
plugged into a 6-pin mini-
DIN jack located on the
back of the drawer (desi-
gnation: IN). You have the
option of ordering a second
6-pin mini-DIN socket for
connecting a further cash
drawer (designation: OUT).
The electronic connection
to the cash drawer is imme-
diately established via a
socket connector when the
cash drawer is installed in
the base plate.
Mind the note on how to connect the cable on page GB-1 !
Connection system
GB - 8
Technical data
Technical data
Height 100 mm
Width 459 mm
Depth 155 mm
Weight 2, 8 kg
Height with hinged cover
open 245 mm
Power supply 12 V DC - 10% to 24 V DC + 10%
Continuous current 25 mA
Max. peak value 300 mA
Ports 6-pin mini-DIN jack to POS system
optional: 6-pin mini-DIN jack for second
cash drawer
Cable lenght optional 0,8, 1,5, or 5 m (BEETLE)
Technical data
GB - 9
Appendix
Installation instructions
The base plate must be separated from the cash drawer before it can be
installed. A screwdriver must be inserted into the emergency open hole in
ordertodoso.
The boreholes on the base plate are for securing the unit:
Hole 1-4 Mounting holes recommended by Wincor Nixdorf.
Emergency open 10 The position of this hole is marked on the diagram.
The screws which are required depend on the arrangement of the table.
The screws and rivet heads must not project beyond the edge of the base
plate.
An all-round clearance of at least 2 mm must be allowed when the cash
drawer is installed.
Technical data
GB - 10
Installation
Remove the metal base plate from the cash drawer by pressing a screwdri-
ver (diameter 3 mm) into the emergency opening bore hole on the undersi-
de of the drawer (see Fig.A).
Fig. A
Install the base plate on the checkout desk so that it is level and horizontal.
Use the flatheaded screws (part of the scope of delivery) to do this.The re-
commended securing bore holes are the positions 1 to 5 (see
Fig.B).
Fig. B 5 mm: Surrounding distance to the base plate with sunk cash drawer
The scew heads (rivet heads) must not protrude from the base plate!
Countersink the spacer element (see Fig. C).
4
3
2
5
1
5 mm
5 mm
5 mm
3mm Ø
Technical data
GB - 11
A bore hole (diameter 3 mm - 6 mm) may be drilled at position 10 (see
Fig. B) under the emergency opening in the checkout desk if your com-
pany permits access to the emergency opening of the KA 16 with a
screwdriver. Make sure beforehand that the emergency opening function is
allowed.
Fig. C
Fig. D (unit of measurement: mm)
Check that the cash drawer latches and unlatches easily when in operati-
on (see the pictograph in the lid).When installing the cash drawer in a re-
cess of the checkout desk, make sure there is a gap of at least 2 mm
around the drawer (see Fig. D). Insert the cable connector in the right
hand socket of the cash drawer (designation: IN).
min 2
5
5
455,5
458,5
min 2
Technical data
GB - 12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Wincor Nixdorf KA16 Cassette Cash Drawer Mode d'emploi

Taper
Mode d'emploi