Kenmore Elite 11042932200 Le manuel du propriétaire

Marque: Kenmore Elite

Modèle: 11042932200

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Front-Loading Automatic Washer

Laveuse automatique _ chargement frontal

Models/Modelos/Modeles 110.42925, 44935

$ = color nQmero, nQmero de color, numero de couleur

Sears Roebuck and Co., Hoffman Estates, IL 60179, U.S.A, www.sears.com

46t 9 7020 3976 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

TABLE OF CONTENTS

PROTECTION AGREEMENTS ....................................................... 2

In the U.S.A ................................................................................... 2

In Canada ..................................................................................... 3

WARRANTY ..................................................................................... 3

PEDESTAL OPTION WARRANTY ................................................. 3

WASHER SAFETY ........................................................................... 4

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Alternate Parts .............................................................................. 5

Options ......................................................................................... 5

Location Requirements ................................................................ 5

Drain System ................................................................................ 7

Electrical Requirements ................................................................ 7

INSTALLATION INSTRUCTIONS .................................................. 8

Remove Transport System ........................................................... 8

Connect the Inlet Hoses ............................................................... 9

Route the Drain Hose ................................................................... 9

Secure the Drain Hose ................................................................. 9

Level the Washer .......................................................................... 9

Complete Installation ................................................................. 10

FEATURES AND BENEFITS ....................................................... 10

WASHER USE .............................................................................. 11

Starting Your Washer ................................................................ 11

Using the Dispenser .................................................................. 12

Pausing or Restarting ................................................................ 13

Changing Cycles, Options and Modifiers ................................. 13

Status Lights .............................................................................. 13

Cycles ........................................................................................ 14

Normal Sounds .......................................................................... 15

Options ...................................................................................... 15

Modifiers .................................................................................... 16

Laundry Guide ........................................................................... 17

LAUNDRY TIPS ............................................................................ 17

Loading ...................................................................................... 18

WASHER CARE ........................................................................... 18

Cleaning Your Washer ............................................................... 18

Water Inlet Hoses ...................................................................... 18

Vacation, Storage, and Moving Care ........................................ 18

TROUBLESHOOTING .................................................................. 19

SERVICE NUMBERS ............................................... BACK COVER

PROTECTION

AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore ®appliance is designed and manufactured for years of

dependable operation. But like all products, it may require

preventive maintenance or repair from time to time. That's when

having a Master Protection Agreement can save you money and

aggravation.

Purchase a Master Protection Agreement now and protect

yourself from unexpected hassle and expense.

The Master Protection Agreement also helps extend the life of

your new appliance. Here's what's included in the Agreement:

v' Expert service by our 12,000 professional repair specialists

v' Unlimited service and no charge for parts and labor on all

covered repairs

v' "No-lemon" guarantee - replacement of your covered

product if four or more product failures occur within twelve

months

v' Product replacement if your covered product can't be fixed

v' Annual Preventive Maintenance Check at your request - no

extra charge

v' Fast help by phone - phone support from a Sears technician

on products requiring in-home repair, plus convenient repair

scheduling

v' Power surge protection against electrical damage due to

power fluctuations

v' Rental reimbursement if repair of your covered product takes

longer than promised

Once you purchase the Agreement, a simple phone call is all that

it takes for you to schedule service. You can call anytime day or

night, or schedule a service appointment online.

Sears has over 12,000 professional repair specialists, who have

access to over 4.5 million quality parts and accessories. That's

the kind of professionalism you can count on to help prolong the

life of your new purchase for years to come. Purchase your

Master Protection Agreement today!

Some limitations and exclusions apply. For prices and

information, call 1-800-827-6655.

Sears Installation Service

For Sears professional installation of home appliances, garage

door openers, water heaters, and other major home items, in the

U.S.A. call 1-800-4-MY-HOME ®.

Maintenance Agreements

Your purchase has added value because you can depend on

Sears HomeCentraP for service. With over 2,400 Service

Technicians and access to over 900,000 parts and accessories,

we have the tools, parts, knowledge and skills to back our

pledge: We Service What We Sell.

Your Kenmore ®appliance is designed, manufactured and tested

to provide years of dependable operation. Yet any major

appliance may require service from time to time. The Sears

Maintenance Agreement offers you an outstanding service

program, affordably priced.

The Sears Maintenance Agreement

• Guarantees tomorrow's service at today's price.

• Eliminates repair bills resulting from normal wear and tear.

• Covers non-technical and instructional service calls.

• Provides an annual Preventive Maintenance Check, at your

request, to ensure that your appliance is in proper running

condition.

Some limitations apply. For information concerning Sears

HomeCentral ®Maintenance Agreements, call

1-800-361-6665.

KENMORE ELITE

WASHER WARRANTY

Limited Lifetime Warranty on Stainless Steel Drum

For the lifetime of the washer from the date of purchase, Sears

will replace the Stainless Steel wash drum due to defective

material or workmanship. After the first year, you will be charged

for labor.

Limited 10-Year Warranty on Plastic Tub*

For the second through tenth year from the date of purchase,

Sears will replace the plastic tub if it is defective in material or

workmanship. After the first year, you will be charged for labor.

Limited 5-Year Warranty on Gearcase Parts*

For the second through fifth year from the date of purchase,

Sears will replace any gearcase parts that are defective in

material or workmanship. After the first year, you will be charged

for labor.

Limited 2-Year Warranty on SENSOR SMART rM

Control Board

For two years from the date of purchase, Sears will replace the

SENSOR SMART rMcontrol board if it is defective in material or

workmanship. You will be charged for labor after the first year.

Full 1-Year Warranty on Mechanical and Electrical Parts

For one year from the date of purchase, when this washer is

installed and operated according to the instructions that come

with it, Sears will repair or replace any of its mechanical or

electrical parts if they are defective in material or workmanship.

Service must be provided by a Sears Service Department in the

United States or Canada or an authorized agent.

Warranty Restriction

If this washer is operated for any purpose other than private

family use, all warranty coverage is restricted to 90 days from the

date of purchase.

Travel or transportation expenses for customers who reside in

remote areas are not covered by this warranty.

Warranty Service

Warranty service is available by contacting the nearest Sears Service

Center in the United States or Canada. This warranty applies only

while the product is in use in the United States or Canada.

This warranty gives you specific legal rights and you may also have

other rights which vary from state to state or province to province.

For Sears warranty information or to contact a Sears Service

Center, please reference the service numbers located on the

back page of this manual.

Sears, Roebuck and Co.

D/817WA, Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

* In Canada a different warranty may apply.

Product Record

In the space below, record your complete model number, serial

number, and purchase date. You can find this information on the

model and serial number label, as shown.

Have this information available to help you quickly obtain assistance

or service when you contact Sears concerning your appliance.

Model number 110

Serial number

Purchase date

Save these instructions and your sales receipt for future

reference.

PEDESTAL OPTION

WARRANTY

Full One-Year Warranty on Mechanical Parts

For one year from the date of purchase, supplier will repair or replace

any of its mechanical parts if defective in material or workmanship.

This Pedestal must be installed with this washer according to the

instructions provided in the Pedestal Installation Instructions.

Warranty Restriction

If the pedestal is subject to other than private family use and or if

the pedestal is used with any other product than those listed in

the installation instructions, the above warranty coverage is null

and void.

Product Record

In the space below, record your complete model number, serial

number, and purchase date. You can find this information on the

model and serial number label.

Have this information available to help you quickly obtain assistance

or service when you contact Sears concerning your pedestal.

Model number 110.

Serial number

Purchase date

Save these instructions and your sales receipt for future

reference.

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic

precautions, including the following:

,, Read all instructions before using the washer.

,, Do not wash articles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, other flammable,

or explosive substances as they give off vapors

that could ignite or explode.

,, Do not add gasoline, dry-cleaning solvents, or

other flammable, or explosive substances to the

wash water. These substances give off vapors

that could ignite or explode.

,, Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not

been used for such a period, before using the

washing machine, turn on all hot water faucets

and let the water flow from each for several

minutes. This will release any accumulated

hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.

[] Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is

used near children.

[] Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator

is moving.

[] Do not install or store the washer where it will be

exposed to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or

attempt any servicing unless specifically recommended

in this manual or in published user-repair instructions

that you understand and have the skills to carry out.

[] See "Electrical Requirements" for grounding instructions.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Assemble the necessary tools and supplies before beginning the

washer installation. The parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

• Pliers (that open to 1%6in. [39.5 mm])

• Flashlight (optional)

Tools needed for installation

• Open end wrench 17 mm and 13 mm

• Level

• Wood block (2" x 4") (5.8 x 10.2 cm)

• Ruler or measuring tape

Parts supplied

Pedestal

A pedestal may be purchased separately for this washer. This

pedestal will add about 13 in. (33 cm) to the height of your unit

for a total vertical height of approximately 51 in. (130 cm).

CC>

Beadedstrap Transport bolt hole plug (4)

Parts listed are available from your local Sears store or Sears

Service Center. For further information, please call

1-800-4-MY-HOME ®(1-800-469-4663}.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already

standpipe taller available)

than 96 in. (2.4 m)

Overhead sewer

Standard 20 gal. (76 L), 30 in. (76.2 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing

suppliers)

Floor drain Siphon break, Part Number 285834;

additional drain hose Part

Number 8318155; and connector kit,

Part Number 285835

Drain hose too 4 ft drain hose extension kit, Part

short Number 285863

Water faucets 2 longer water fill hoses:

beyond reach of 6 ft (1.8 m) Part Number 76314,

fill hoses 10 ft (3.0 m) Part Number 350008

Optional Pedestal

This pedestal (with storage drawer) is available in three colors:

White - Part Number 42842

Bisque - Part Number 42844

Graphite - Part Number 42846

To order, call your local Sears store. For further information,

please call 1-800-4-MY-HOME ®(1-800-469-4663).

Stack Kit

Are you planning to stack your Kenmore HE3t washer and dryer?

Todo so, find the stack kit (8541503) in the drum of the matching

Kenmore dryer. Follow instructions included with the kit.

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer "walk."

Your washer can be installed under a custom counter, or in a

basement, laundry room, closet, or recessed area. (See "Drain

System.")

Companion appliance location requirements should also be

considered. Proper installation is your responsibility.

You will need

• A water heater set to deliver 120°F (49°C) water to the washer.

• A grounded electrical outlet located within 5 ft (1.5 m) of

where the power cord is attached to the back of the washer.

(See "Electrical Requirements.")

• Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of

20-100 psi (137.9-689.6 kPa).

• A level floor with a maximum slope of 1 in. (2.5 cm) under

entire washer. Installing the washer on carpeting is not

recommended.

• A sturdy and solid floor to support the washer with a total

weight (water and load) of 400 Ibs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C).

Some water can remain in the washer and can cause damage in

low temperatures.

Installation clearances

• The location must be large enough to allow the washer door

to be fully opened.

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door, and

floor moldings.

• Additional spacing of 1 in. (2.5 cm) on all sides of the washer

is recommended to reduce noise transfer.

• Companion appliance spacing should also be considered.

Washer Dimensions

38"

(96.5 cm)

3 V2II /

" ,, (80.0 cm)

Recommended installation spacing for custom

undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

39" min

(99.0 era)

1" 27" 1"

(2.5 cm)'--'_(68.6 cm)"_D'_ - (2.5 cm)

Recommended installation spacing for recessed or

closet installation, with or without a pedestal

The dimensions shown are for the recommended spacing.

Recessed area or closet installation

| 48 in? *

34" / (310 cm 2) _

(864 c1_)

24 in? *

(155 cm 2)

I1'1_ sl,__"141_-

(2.5 cra) (80cm) (102 cm)

-- 3"

76 cm)

_.(76 cm)

!. Side view - closet or confined area

2. Closet door with vents

(2.5 cm) (68.6 cm) (25 cm}

1.Recessedarea

Recessed or closet installation - Washer on pedestal

-- ,4

I1"I<-31/,"_'14"

/2.5cra) (80cm) (102 cm}

2. Side view - closet or confined area

Recommended installation spacing for recessed or

closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in. 2 *

(310_ m2)

24 in.2 *

(155 cm 2 )

3" (7.6 cm)

6" (1_.2 cm)

5½"** --_-

(14 cm)

*Min. top and bottom air openings for closet

door.

**External exhaust elbow requires additional

space.

***Wall, door and floor molding may require

additional spacing.

Recommended installation spacing for cabinet

installation

• The dimensions shown are for the recommended spacing.

• For cabinet installation, with a door, the minimum ventilation

openings in the top are required.

(17.8 crn)

7" (17.8crn)

[9"

r (22.9crn)

4 _ .............................................

(lO.2crn) (80.Ocrn) (2.5crn) (2.5crn) (68.6cm) (2.5crn)

The washer can be installed using the standpipe drain system

(floor or wall), the laundry tub drain system, or the floor drain

system. Select the drain hose installation method you need. (See

"Alternate Parts.")

30" min.

(76.2 cm)'

Standpipe drain system - wall or floor (view I & 2)

The standpipe drain requires a minimum diameter standpipe of

2 in. (5 cm). The minimum carry-away capacity can be no less

than 17 gal. (64 L) per minute.

The top of the standpipe must be at least 30 in. (76.2 cm) high

and no higher than 96 in. (2.4 m) from the bottom of the washer.

28 inX

(71crn)

Laundry tub drain system (view 1)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 30 in. (76.2 cm) above the

floor.

Floor drain system (view 2)

The floor drain system requires a siphon break that may be

purchased separately. (See "Alternate Parts.")

The siphon break must be a minimum of 28 in. (71 cm) from the

bottom of the washer. Additional hoses might be needed.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to folow these instructions can result in

death, fire, or electrical shock.

A 120-volt, 60-Hz., AC-only, 15- or 20-ampere, fused

electrical supply is required. Time-delay fuse or circuit

breaker is recommended. It is recommended that a separate

circuit serving only this appliance be provided.

This washer is equipped with a power supply cord having a

3 prong ground plug.

To minimize possible shock hazard, the cord must be

plugged into a mating, 3 prong, ground-type outlet, grounded

in accordance with local codes and ordinances. If a mating

outlet is not available, it is the personal responsibility and

obligation of the customer to have the properly grounded

outlet installed by a qualified electrician.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

• Donotgroundtoagaspipe.

• Checkwithaqualifiedelectricianifyouarenotsurethe

washerisproperlygrounded.

• Donothaveafuseintheneutralorgroundcircuit.

1.3 prong grounding plug

2. 3 prong grounding-type

wall receptacle

3. Grounding prong

4. Power supply cord

GROUNDING INSTRUCTIONS

For a grounded, cord=connected washer:

This washer must be grounded. In the event of a mal-

function or breakdown, grounding will reduce the risk

of electrical shock by providing a path of least resist-

ance for electric current. This washer isequipped with

a cord having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into an

appropriate outlet that isproperly installed and ground-

ed in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or serviceman

if you are in doubt as to whether the appliance is prop-

erly grounded.

Do not modify the plug provided with the appliance -

if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead

on the appliance.

INSTALLATION

INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

washer.

Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the unit is

within approximately 3 ft (90 cm) of the final location.

There are 4 bolts in the rear panel of the washer that support the

suspension system during transportation.

Using a 13 mm wrench, loosen each ofthe bolts.

Once the bolt is loose, move itto the center of the hole and

completely pull out the bolt, including the plastic spacer

covering the bolt and the cable attached to the bolt. The

power cord will be attached to all 4 bolts.

3. Once all 4 bolts are removed, remove the power cord from

each bolt holder, and discard bolts, plastic spacers, and

cables.

4. Close the holes with the transport bolt hole plugs.

Connectthe inlet hoses to the water faucets

Make sure the washer drum is empty.

1. Using pliers, check for tightness of hose couplings already

attached to the washer.

NOTE: Do not overtighten. Damage to the connection can

result,

2. Attach the hose with the red color indicator to the hot water

faucet. Screw on coupling by hand until it is seated on the

washer.

3. Attach the hose with the blue color indicator to the cold water

faucet. Screw on coupling by hand until it is seated on the

washer.

4. Using pliers, tighten the couplings with an additional two-

thirds turn,

NOTE: Do not overtighten, Damage to the coupling can result,

5. Turn on the water faucets and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference,

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Proper routing of the drain hose protects your floors from

damage due to water leakage. Carefully read and follow these

instructions.

The drain hose is connected to your washer.

eeou ® Hose

Drape the power cord over the washer top.

Secure the drain hose to the laundry tub leg or standpipe with

the beaded strap provided. (See illustrations 1 and 2.)

If the washer faucets and the drain standpipe are recessed

(see illustration 3), put the hooked end of the drain hose in the

standpipe. Tightly wrap the beaded strap around the water

inlet hoses and the drain hose.

Do not force excess drain hose into the standpipe.

,u, _ , _' _ -,_/ / _)_

Properly leveling your washer prevents excessive noise and

vibration.

1. Check the levelness of the washer by placing a level on the

top edge of the washer, first side to side, then front to back.

If the washer is against a wall, move the washer out slightly

before tipping back. If the washer is not level, first prop the

front with a wood block (2" x 4") (5.8 x 10.2 cm) and adjust

the feet as necessary; then prop the back and adjust feet as

necessary. Repeat this step until washer is level.

After the washer is level, use a 17 mm open-end wrench to

turn the nuts on the feet tightly against the washer cabinet.

All 4 feet must be tightened. If the nuts are not tight against

the washer cabinet, the washer may vibrate.

3. Slide the washer to its final location,

4. Confirm the levelness of the washer.

To prevent drain water from gotng back into the washer:

• Do not straighten the drain hose, and do not force excess

drain hose into standpipe. Hose should be secure, but loose

enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

Floor drain

You may need additional parts. (See Floor Drain under "Alternate

Parts,")

1. Checktheelectricalrequirements.Besurethatyouhavethe

correctelectricalsupplyandtherecommendedgrounding

method.(See"ElectricalRequirements.")

2. Checktobesureallpartsarenowinstalled.Ifthereisan

extrapart,gobackthroughthestepstoseewhichstepwas

skipped.

3. Check to be sure you have all of your tools.

4. Dispose/recycle all packaging materials.

5. Check to be sure the water faucets are on.

6. Check for leaks around faucets and inlet hoses.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

7. Plug into a grounded 3 prong outlet.

8. Read "Washer Use."

9. Totest and to clean your washer, measure 1/2the normal

recommended amount of powdered or liquid High Efficiency

(HE) detergent or 1/4the normal recommended amount of

regular powdered or liquid detergent. Pour the detergent into

the detergent dispenser. Select NORMAL/CASUAL, and then

select START. Allow the washer to complete one whole cycle.

FEATURES AND

BENEFITS

SENSOR SMART TM Electronic Controls

Flexible electronic controls are easy to use whether you are a

beginner or an expert.

Detergent Advantage System Dispenser

The four compartments in the dispenser allow loading of all

laundry additives before the washer is started. The additives will

be dispensed into the wash at the optimal time for high

performance cleaning. TIMED BLEACW Mrelease is included in

the detergent advantage system. The detergent is added at the

beginning of the cycle and the bleach is added after the enzymes

have had a chance to do their cleaning. The fabric softener is

dispensed in the rinse cycle. The Detergent Advantage System

Dispenser tray is easily removed for cleaning.

Auto Water Level

Adjusting to the size of the load, this feature allows the washer to

use the minimal amount of water needed to clean and rinse the

clothes. With a low water level, you can obtain the same results

with smaller amounts of additives. Because only the required

amount of water is used, the washer saves energy, too.

Larger Load Size

Since there is no agitator, you can wash larger, bulkier items like

an average size sleeping bag. You are also able to wash more

clothes at one time, which means fewer loads. You can wash a

pillow or a large stuffed teddy bear.

Suspension System

To reduce washer "walk" and "off-balance" conditions, your new

washer combines:

• 2 Springs to isolate vibration

• 4 Shock absorbers at the washer base to minimize movement

Stainless Steel Drum

The Stainless Steel drum eliminates corrosion and enables higher

spin speeds for more water extraction, reducing drying time.

Adaptive Variable Speed Motor

The motor adapts to the load size and to the cycle selected to

give the optimum cleaning, rinsing, and spinning conditions. The

motor can handle slow speeds needed for wool and delicate

items and is powerful enough to drive a large clothes load into a

1,200 rpm spin.

High-Efficiency Wash System

Your new front-loading, high-efficiency washer saves time with

fewer, larger loads, conserves resources and lowers your water

and energy bills too.

Spin Speeds

This washer automatically selects the spin speed based on the

cycle selected. This factory setting can be changed, however.

This washer offers up to six different spin speed choices.

Thermal Optimizer

The heating system ensures that the wash water is heated to the

preset temperature for Heavy Duty, Whitest Whites, Sanitary, and

the Stain Treat option. It also provides "stepped cleaning" when

using the sanitary cycle or the stain treat option. "Stepped

cleaning" starts the wash cycle with warm water to remove stains

(such as blood or grass). The water continues heating in order to

remove stains such as dirty mechanical oil. During the sanitary

cycle, the thermal optimizer can heat the water to temperatures

that will destroy 99.999% of three common types of bacteria

found in soiled laundry.

Add A Garment

When lighted, Express Wash, Normal/Casual, Heavy Duty,

Whitest Whites, and Sanitary can be paused and the door

unlocked so you can add a garment that may have been

forgotten when loading the washer. The ADD A GARMENT status

light will stay lit for the first 8 minutes of a cycle.

CATALYST _ Cleaning Action with Direct Injection

A concentrated detergent solution is sprayed onto the clothes at

the beginning of the cycle to ensure that the detergent comes

into contact with the clothes as quickly as possible, removing

stains from your clothes without pretreating.

Dynamic Balance

A precision balancing system that allows the washer to reach

spin speeds of 1,200 rpm. The washer spins faster so that

clothes coming out of the washer will dry faster. In addition, if the

Dynamic Balance system detects off balance loads during

spinning, it redistributes the clothes so that they are evenly

balanced.

WASHER USE

WASH CYCLES

EXPRESS WASH

S1ArUS NOR MA L_//

ADDAGA_{_ENTO CASUA

waste DUTY T

RINSe RINS_ / SPIN _ w_ss _L_

..... WN,PES,-

¢IOT_S CIIA_ o DRAIN ] SPIN WHITES

_Ess& _0tDs ' --_' ULTRA

set, tos TOIOC_/

co _o L_CK_oe UNL0C_CONTRO SANITARY HANDINASH

ES_IMa_EI)

YI_EaEMaI_U_G

e N_AVY

• NORMAL

m LIGHT

Fire Hazard

Never place items in the washer that are

dampened with gasoline or other flammable

fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of

oil on it (including cooking oils).

Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

The following is a guide to using your washer. Please refer to

specific sections of this manual for more detailed information,

Do not store laundry products on the top surface of this washer.

Vibration is normal during operation.

First Wash Cycle Without Laundry

Before washing clothes for the first time, choose NORMAL/

CASUAL cycle and run it without clothes, After installation, if a

complete cycle has not been run without clothes, use _/_the

normal recommended amount of powdered or liquid High

Efficiency (HE) detergent or _ the normal recommended amount

of regular powdered or liquid detergent, This initial cycle serves

to ensure the interior is clean before washing clothes.

1. To load washer

Open the washer door by pulling on the handle.

Sort laundry according to color and type of fabric. Place a

load of sorted clothes in the washer. Do not overload washer.

Overloading can cause poor cleaning.

• The washer can be fully loaded, but not tightly packed.

Washer door should close easily.

• Mix large and small items. Avoid washing a single item,

Load evenly.

DELAy

OPTIONS MOI)_RERS

PREWASH Au oTzt,_Cam_,o_

EXTRAHOT/ COLD _ EXTRANIGH

STAIN TREAT • NOT ! COLD • HIGH

• WARM / WARM ® MEDIUM

AUTO SOAK • WARM ] COLD • LOW

• COLD/ COLD O EXTRALOW

2ND RINSE OTAP COLD / COLD O NO SPIN

HIGH

LOW

OFF

_XTENDED SPIN WATER TEMP SPIN SPEED END of CYCLE SIGNAL

It is recommended that you wash small items such as

infant socks in a mesh garment bag.

When unloading garments, occasionally check under the

rubber rim at the front of the tub for small items.

Close the washer door by pushing it firmly until the lock

clicks, The washer door will remain locked during the wash

cycle.

NOTE: After any wash cycle is completed, the door must be

opened and then closed before a new cycle can begin. The

door can be opened only if PAUSE/CANCEL is selected while

the ADD A GARMENT light is glowing or if the cycle has been

canceled. See "To Cancel a Cycle,"

Open the Dispenser Drawer and add laundry products to the

detergent, bleach, or fabric softener compartments. Close

drawer slowly to avoid spills. See "Using the Dispenser."

NOTE: For best performance, use High Efficiency

detergents. The package for this type of detergent will be

marked "HE" or "High Efficiency." The HE_t "wash action"

along with less water could create too much sudsing with a

regular detergent.

4. Turn on the washer by selecting one of the WASH CYCLES.

The indicator light for the selected cycle will glow. When

selecting a Wash Cycle, the preset options, Water Temp, Spin

Speed, and Soil Level for the selected cycle will glow. The

display shows the estimated time remaining. The preset

settings provide the recommended fabric care for the

selected cycle. See "Wash Cycles."

5. Select the desired OPTIONS. Not all Options are available

with all cycles. See "Options."

6. Select the desired MODIFIERS. Not all Modifiers are available

with all Cycles and Options. See "Modifiers."

7. If desired, select the END OF CYCLE SIGNAL. The signal is

helpful when you are washing items that should be removed

from the washer as soon as it stops. Select HIGH or LOW.

8. To begin the wash cycle immediately

Select and hold START (for approximately I second).

• If you do not select START within 5 minutes of choosing a

cycle, the washer automatically shuts off.

• When the wash cycle is complete, the CLOTHES CLEAN

status light glows, the door unlocks, and the wash load

can be removed from the washer. The washer powers

down automatically 5 minutes after the cycle is complete

and the CLOTHES CLEAN light goes off. To power down

the washer manually after the wash cycle is complete,

select PAUSE/CANCEL once.

To begin the wash cycle later

Select DELAY until the desired delay time (in hours) shows in

the Estimated Time Remaining display. Select START.The

countdown to the wash cycle will show in the display window.

Usisg

Your new washer has a dispenser drawer with four separate

compartments for your laundry products--two are for detergent,

one is for liquid chlorine bleach, and one is for liquid fabric

softener. Laundry products are diluted and dispensed

automatically at the proper time during the wash cycle, making it

unnecessary for you to return to the washer during the cycle to

add them.

It is normal for small amounts of water to remain in the

dispensers when the wash cycle is complete.

Do not put laundry additives directly into the wash tub, Always

use the proper dispensers when adding laundry products.

Choosing the Right Detergent

For best washing performance, use a High Efficiency (HE), or

low-sudsing, detergent, Regular detergents may cause

oversudsing in the washer. If a High Efficiency detergent is

unavailable, use 1/2the recommended amount of regular

detergent,

NOTE: Use of Regular detergent may lead to unsatisfactory

performance over time.

Most detergents formulated for hand-washing are not meant for

front-loading washers and may cause oversudsing. Start with 1/4

the recommended amount. Ifoversudsing occurs, try a detergent

formulated for high efficiency washers.

To fill dispenser compartments

1. Pull out the dispenser drawer.

2. Add the desired laundry product to the proper compartment.

3. Push in the dispenser drawer carefully and completely (to

avoid spillage).

Dispenser

1. Prewash detergent compartment

2. Separator

3. Main Wash detergent compartment

4. Dispenser release lever

5. Chlorine bleach compartment

6. Fabric softener compartment

Prewash detergent compartment

(Number 1 in Dispenser Illustration)

Add detergent to this compartment when using the Prewash

option or Auto Soak, Liquid or powdered detergent may be used

in this compartment. The detergent will automatically be

dispensed during Prewash if the Prewash option is selected or

during the soak time if Auto Soak is selected.

• If you use High Efficiency (HE) detergent, add 1/3the

recommended amount to the prewash compartment and ¾

the recommended amount to the main wash compartment.

• If you use regular detergent, add ½ of the recommended

amount to the prewash compartment and 1/3of the

recommended amount to the main wash compartment.

Main Wash detergent compartment

(Number 3 in Dispenser Illustration)

Add liquid or powdered detergent to this compartment for your

main wash cycle. The detergent separator must always be in

place, either in the front or back position.

IMPORTANT: If you are using the Prewash option, the Auto Soak

with a wash cycle, or Delay, powdered detergent must be used in

the main wash compartment since liquid detergents may seep

out of the main wash compartment during the prewash, soak

time, or delay before the main wash begins.

• Do not fill beyond the "MAX" level.

• Liquid or powdered color-safe bleach may be added to the

Main Wash compartment along with the same type of

detergent, liquid or powdered.

Liquid detergent: Put the SEPARATOR in the front position,

between the guides, as shown following. There will be no gap

between the bottom of the wash cycle detergent

compartment and the bottom of the separator.

R (_ PREWASH A

MAINWASHV

Separator in front position, between guides

UQUI

1. Separator

2. Guide

Powdered detergent: Put the SEPARATOR in the back

position, behind the guides, as shown following. There will be

a gap between the bottom of the wash cycle detergent

compartment and the bottom of the separator.

U,I

[] POWDER _ PREWASHz_

Separator in back position, behind guides

1. Separator

2. Guide

LIQUi

NOTE: The separator will be in the powder (back) position when

shipped from the factory.

Chlorine bleach compartment

(Number 5 in Dispenser Illustration)

Add NO MORE THAN 1/3cup (80 mL) liquid chlorine bleach to this

compartment. The bleach will be automatically diluted and

dispensed at the best time during the first rinse after the wash

cycle. This compartment cannot dilute powdered bleach.

• Always measure liquid chlorine bleach. Use a measuring cup

with a pour spout; do not guess.

• Do not fill beyond the "MAX" level.

NOTE: Overfilling could cause severe garment damage.

Fabric Softener compartment

(Number 6 in Dispenser Illustration)

Add 1/4cup (60 mL) liquid fabric softener to this compartment.

Fabric softener will be automatically dispensed in the final rinse.

• Do not fill beyond the "MAX" level.

Psus n{ s

To pause the washer at any time, select PAUSE/CANCEL

To continue the cycle, select and hold START (for

approximately 1 second).

Not all Options and Modifiers are available with all Cycles.

Cycles, Options and Modifiers can be changed anytime before

START is selected.

Options and Modifiers can be changed anytime after START is

selected and before the start of the selected Option or Modifier.

To cancel a cycle and select a new cycle

1. Select PAUSE/CANCELtwice.

2. Select desired cycle.

3. Select the desired OPTIONS.

4. Select and hold START (for approximately 1 second) to restart

the washer at the beginning of the new cycle.

To cancel a cycle

1. Select PAUSE/CANCEL twice.

2. The washer powers down, the door unlocks, and clothes can

be removed.

NOTE: If the water level or the temperature is too high, the

washer will drain automatically before the door unlocks.

To change Options or Modifiers after the cycle has started

1. Select PAUSE/CANCEL.

2. Select the desired OPTIONS or MODIFIERS.

3. Select and hold START (for approximately I second) to

continue the cycle.

To drain the washer manually

1. Select PAUSE/CANCEL.

2. Select DRAIN/SPIN.

3. Select and hold START (for approximately 1second) to begin

the drain.

4. When the spin is complete, the door unlocks. Items can be

removed from the washer.

These lights show which portion of the cycle the washer is

operating. They also indicate when you can add an additional

item to the wash cycle and when the controls are locked.

STATUS

ADD A GARMENT•

SOAK/PREWASH •

WASH •

RINSE@

SPIN0

CLOTHESCLEANO

CONTROLLOCKED•

Adding items

You can add items to the washer after the cycle has started for

Express Wash, Normal/Casual, Heavy Duty, Whitest Whites, and

Sanitary if the ADD A GARMENT status light is glowing.

To add items

1. Select PAUSE/CANCEL The washer door unlocks, and items

can be added.

2. To continue the cycle, close the door and select and hold

START (for approximately 1 second).

Clothes Clean

The Clothes Clean light stays on for 5 minutes after the cycle is

complete. The washer will then power down.

Locking controls

The Control Lock prevents unintended use of the washer. You

can also use the control lock feature to prevent unintended cycle

or option changes during a cycle. When CONTROL LOCKED is

lit, all buttons are disabled except for Pause/Cancel and Start.

You can lock the controls while the washer is operating.

To lock the controls

Select and hold DRAIN/SPIN for 3 seconds.

DRAmN / SPIN

PRESS & HOLD 3

SECONDS TO LOCK /

UNLOCK CONTROL

The CONTROL LOCKED status light glows.

To unlock the controls

Select and hold DRAIN/SPIN for 3 seconds until the CONTROL

LOCKED Status light turns off.

Estimated Time Remaining

The cycle times vary automatically based on your water pressure,

water temperature, detergent, and clothes load. The cycle time

will be extended if oversudsing occurs or the load is unbalanced.

Wash Cycles

Choose Wash Cycles by selecting the button next to the desired

cycle. Each cycle is designed for different types of fabric and soil

levels.

WASHCYCLES

EXPRESSWASH

NORMAL/

CASUAL"._

WHITES

DELICATE

SILK

WOOL

ULTRA

SANITARY HANDWASH

Each cycle has a preset Soil Level (cycle time), Water

Temperature, Spin Speed and may have preset Options. The

preset settings provide the recommended fabric care for the

selected cycle.

The preset settings can be changed anytime before START is

selected. Not all Options and Modifiers are available with all

Cycles. (To change settings after the cycle has started, select

PAUSE/CANCEL, then select the desired settings. Select and

hold START [for approximately 1 second] to continue the

cycle.)

Preset cycle settings

Each cycle has a preset Cycle Time, Water Temp, and Spin

Speed. The preset settings provide the recommended fabric care

for the selected cycle. See chart.

Cycle Soil Level Water Temp Spin Speed

(hr:min)

Sanitary Heavy Extra Hot/Cold Extra High

(2:00)

Whitest Heavy Hot/Cold Extra High

Whites (1:10)

Heavy Heavy Hot/Cold Extra High

Duty (1:40)

Normal/ Normal Warm/Cold High

Casual (0:45)

Express Light Warm/Cold Extra High

Wash (0:30)

Delicate Normal Warm/Cold Low

(0:35)

Silk Normal Cold/Cold No spin

(0:30)

Wool Normal Cold/Cold Low

(0:35)

Ultra Normal Cold/Cold Extra Low

Handwash (0:35)

Sanitary

Use this cycle to clean heavily soiled colorfast fabrics. This cycle

combines a very hot water temperature and fast speed tumbling

to help ensure the removal of heavy soils and stains. It is

recommended that you set your hot water heater to 120°F (49°C)

to ensure proper performance during this cycle. The Sanitary

cycle also helps eliminate 99.999% of 3 common infectious

bacteria, even when no bleach is used. Extra high speed spin

helps shorten drying time.

Whitest Whites

This cycle is especially designed for cleaning loads of soiled

white fabrics with the addition of bleach. Hot washing

temperatures assure optimal bleach activity. An additional rinse

provides optimal rinse performance to avoid chlorine residues on

your laundry. This cycle combines fast speed tumbling, longer

wash time, and extra high speed spin to shorten drying time.

Heavy Duty

Use this cycle to wash loads of sturdy, colorfast fabrics and

normally soiled garments. This cycle combines fast speed

tumbling, longer wash time, and extra high speed spin to shorten

drying times. If the water temperature is lower than needed for

this cycle, the heater will warm the water to the optimum

temperature.

NOTE: Stain Treat is a default option for this cycle. To ensure

best performance, the water is heated as the cycle progresses.

This gradual heating assists in the removal of organic soils such

as blood. Stain Treat must be turned off to change the modifiers.

Normal/Casual

Use this cycle to wash loads of no-iron fabrics such as sport

shirts, blouses, casual business clothes, permanent press

blends, cottons and linens, and synthetic fabrics. This cycle

combines medium speed tumbling, high speed spin, and a load

cooling process to reduce wrinkling.

Express Wash

Use this cycle to wash small loads of lightly soiled garments that

are needed in a hurry. This cycle combines fast speed tumbling, a

shortened wash time, and extra high speed spin to shorten

drying time.

Delicate

Use this cycle to wash sheer fabrics and lingerie. This cycle

combines low speed tumbling and low speed spin for gentle

fabric care.

Silk

Use this cycle to clean washable silk garments. (Check label

instructions to make sure that garment is washable.) This cycle

gently tumbles and drains without spinning to gently clean

garments and minimize wrinkling. Because there is no spinning

action, garments will contain a higher amount of water at the end

of this cycle.

Wool

Use this cycle to clean washable woolen garments. (Check label

instructions to make sure that garment is washable.) This cycle

features gentle tumbling and low speed spin to minimize creasing

and shrinkage.

Ultra Handwash

Use this cycle to clean hand washable and special-care

garments. Similar to the way garments are hand washed in a

sink, the wash action of this cycle combines periods of extra low

speed tumbling and soaking. Extra low speed spin reduces

wrinkling.

Extra Cycles

Extra Cycles can be chosen by selecting the button above the

desired cycle.

RINSE / SPiN

DRAIN / SPIN

You can change the selection anytime before START is selected.

Rinse/Spin

Use this cycle to get a rinse and spin only. This cycle combines

fast speed tumbling and extra high speed spin. If desired, you

can reduce the spin speed by selecting the speed you want from

the SPIN SPEED modifier.

Rinse/Spin is useful for

• Loadsthat need rinsing only.

• Adding fabric softener to a load using the fabric softener

dispenser.

Drain/Spin

Use this cycle to drain your washer or to drain and spin your

wash load. The spin speed is preset to extra high. If desired, you

can reduce the spin speed by selecting the speed you want from

the SPIN SPEED modifier.

NOTE: Loads of synthetics, delicate fabrics, handwashables, and

woolens should be drained with no spin or low spin to avoid

fabric stress.

As with any new product, you will hear sounds that you are not

accustomed to. You may hear various sounds when the door is

locked or unlocked, and during the washing, rinsing, or spinning

process. Between changes in wash actions, there will be

momentary pauses. You will hear water spraying and splashing

during the wash and rinse cycles. These new sounds and pauses

are part of normal washer operation. (See "Troubleshooting.")

You can customize your wash by adding OPTIONS to your cycle

selections. You can add or change an option after starting a cycle

anytime before the selected option begins. Not all Options are

available with all cycles.

OPTIONS

PREWASN

STAIN TREAT

AUTO SOAK

2ND RINSE

EXTENDED SPiN

See the "Laundry Guide" section for an overview of possible

options for each Wash Cycle selection.

You can select more than one option for a cycle. Some

options cannot be added to some cycles, for example, Stain

Treat cannot be added to the Express Wash cycle.

If an option is available with a selected cycle, the light for that

option will glow when selected.

If an option is unavailable with a selected cycle, there will be a

short tone and the light for that option will not glow when

selected.

Prewash

Use this option for loads of heavily soiled items that need

pretreatment. This option adds a 15 minute prewash and drain to

the main wash cycle.

• Add detergent to the Prewash and Main Wash compartments

of the Dispenser Drawer.

• When using Prewash, do not use liquid detergent in the Main

Wash compartment. Use powdered detergent for the main

wash cycle (see "Using the Dispenser").

NOTE: The Prewash and Auto Soak options cannot be selected

in the same cycle.

Stain Treat

Use this option for heavily soiled loads that need improved stain

treatment. When Stain Treat is selected, the water temperature of

the selected wash cycle is automatically set to warm. The water

will then be heated to a hot water temperature to aid in stain

removal. This option will provide optimal removal of organic

stains such as blood.

NOTE: If Stain Treat is selected with the Sanitary cycle, the water

will be heated to a very hot temperature.

Auto Soak

Use the Auto Soak option for loads of heavily soiled cotton, linen,

polyester or nylon with set-in stains. During Auto Soak, water will

be added to the drum and the laundry will be equally distributed

by a short tumbling phase. Laundry will then be soaked by

phases without drum movement. After soaking, the washer

drains without spinning.

Added to a Wash Cycle: A 30 minute soak time is added to the

main wash cycle to improve removal of set-in stains.

1. Add detergent to both the Prewash and Main Wash

compartments of the Dispenser Drawer.

NOTE: The Auto Soak and Prewash options cannot be

selected in the same cycle. Use powdered detergent for the

main wash cycle because liquid detergent will seep into the

washer during Auto Soak.

Select a Wash Cycle.

Select AUTO SOAK.

NOTE: For cycles with hot wash temperatures, the soak

temperature will be set to warm; otherwise, the soak

temperature will be the same as the wash temperature.

4. Select and hold START (approximately 1 second). After

soaking, the washer drains and the wash cycle starts.

Without a Wash Cycle: Provides a soak time with warm or cold

water followed by drain.

1. Add detergent only to the Prewash compartment of the

Dispenser Drawer.

2. Select DRAIN/SPIN or RINSE/SPIN first, then AUTO SOAK.

3. Choose the desired soak temperature.

4. Select and hold START (approximately 1 second).

2nd Rinse

A second rinse can be used to ensure the removal of detergent or

bleach residue from garments. This option provides an additional

rinse with the same water temperature as the first rinse.

Extended Spin

Use this option to add an additional spin to any cycle to improve

drying times for some heavy fabrics or special-care items by

reducing excess water, which may save energy.

Preset cycle settings of Water Temperature, Wash/Rinse, and

Spin Speed can be changed. You can change a modifier after

starting a cycle anytime before the selected Modifier begins. Not

all Modifiers are available with all options and cycles.

MODIFIERS

AUTOTFMPCONTROl

Q EXTRA HOT/COLD 0 EXTRA HIGH

• HOT/ COLD • HIGH

• WARM t WARM • MEDIUM

• WARM / COLD • LOW • HIGH

• COLD / COLD • EXTRA LOW • LOW

0 TAP COLD / COLD • NO SPIN Q OFF

C) C) C)

WATER TEMP SPIN SPEED END of CYCLE SIGNAL

WASH / RINSE

To change the water temperature, select the WATER TEMP

button until the desired setting glows.

To change the spin speed, select the SPIN SPEED button

until the desired setting glows.

o HEAVY

e NORMAL

• LIGHT

SOIL LEVEL

• To change cycle time, select SOIL LEVEL button.

• To change the loudness of the End of Cycle Signal, select

END of CYCLE SIGNAL.

Wash/Rinse Temp

Select a water temperature based on the type of load you are

washing. Use the warmest water safe for fabrics. Follow garment

label instructions.

Warm rinses leave the loads dryer than cold rinses. Warm rinses

increase wrinkling. In cold climates, a warm rinse makes the load

more comfortable to handle. Cold rinses save energy.

Temperature Guide

Wash Water Temperature Suggested Fabrics

Extra Hot Sturdy colorfast fabrics

153°F (67°C) Heavy soils

HOT* Whites and pastels

140°F (60°C) Heavy soils

WARM Bright colors

104°F (40°C) Moderate to light soils

COLD Colors that bleed or fade

77°F (25°C) Light soils

In wash water temperatures colder than 70°F (21°C),

detergents do not dissolve well. Soils may be difficult to

remove.

* When used with Stain Treat option, the water is heated

gradually to assist in the removal of organic soils such as

blood.

Auto Temp Control •

ATC (Auto Temp Control) electronically senses and maintains a

uniform water temperature. ATC regulates incoming hot and cold •

water. The ATC is automatically turned ON when a cycle is

selected. (See "Preset Cycle Settings" in "Cycles.")

• ATC ensures consistent cleaning. •

• ATC works for the wash temperature with Extra Hot/Cold,

Hot/Cold, Warm/Warm, Warm/Cold, and Cold/Cold settings.

The Cold rinse temperatures depend on the cold water at

your faucet.

For the Tap Cold/Cold setting, both wash and rinse

temperatures depend on the cold water at your faucet.

ATC works for the rinse temperature with the Warm/Warm

setting. The cold rinse temperature depends on the cold

water at your faucet.

Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these

washer cycles.

CYCLE SUGGESTED LOAD TYPE AVAILABLE OPTIONS

Prewash* Stain Treat Auto Soak* 2nd Rinse Extended

Spin

Sanitary Heavily soiled underwear, towels, work ,1 ,1 ,1 ,1 ,1

clothes, diapers, etc.

Whitest Heavily soiled white fabrics v' v' v' v' v'

Whites

Heavy Duty Normally soiled underwear, towels, V' V' V' V' V'

shirts, etc., made of cotton

Normal/ Lightly to normally soiled blouses, V' V' V' V' V'

Casual shirts, overalls, etc., made of polyester,

nylon, cotton, linen, or cotton blends

Express Wash Lightly to normally soiled overalls and V' V' V'

sportswear made of cotton, polyester,

nylon, and cotton blends

Delicate Curtains and delicate clothing, dresses, V V V

skirts, shirts and blouses

Silk Fabrics made of silk identified as V

machine washable

Wool Woolens with a felt-free finish, identified V

as machine washable

Ultra Fabrics made of silk, special-care items V'

Nandwash marked "Handwashable"

*Prewash and Auto Soak cannot be selected at the same time.

LAUNDRY TIPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of

your garments.

• Close zippers, snaps, and hooks to avoid snagging other

items. Remove pins, buckles, and other hard objects to avoid

scratching the washer interior. Remove non-washable trim

and ornaments.

• Empty pockets and turn them inside-out.

• Turn down cuffs; brush away lint and dirt.

• Turn synthetic knits inside-out to avoid pilling.

• Tie strings and sashes so they will not tangle.

• Mend tears, loose hems, and seams.

• Treat spots and stains.

• Stained or wet garments should be washed promptly for best

results.

Sorting

• Separate heavily soiled items from lightly soiled ones, even if

they would normally be washed together. Separate lint-givers

(towels, chenille) from lint-takers (corduroy, synthetics,

permanent press). When possible, turn lint-givers inside-out.

• Separate dark colors from light colors, colorfast items from

noncolorfast items.

• Sort by fabric and construction (sturdy cottons, knits, delicate

items).

Unloading

• Remove clothes from washer after the cycle is completed.

Metal objects such as zippers, snaps, and buckles may rust if

left in the washer basket for a long time.

Loading suggestions (maximum size loads).

Heavy Work Clothes

4 jeans 2 sweatpants

4 workpants 2 sweatshirts

4 workshirts

Towels

10 bath towels

10 hand towels

14 washcloths

Mixed Load

3 sheets (1 king, 2 twin) 9 T-shirts

4 pillowcases 9 shorts

3 shirts 10 handkerchiefs

3 blouses

WASHER CARE

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to keep it looking

new. Use mild soap and water. Do not use abrasive products.

Cleaning the interior

Use a soft damp cloth or sponge to occasionally wipe the inner

door to remove any detergent residue. Use mild soap and water.

Do not use abrasive products.

Cleaning the door seal

Use a soft damp cloth or sponge when necessary. Check the fold

of the seal periodically for any foreign objects.

Cleaning the dispenser drawer

The dispenser drawer is removable for easy cleaning.

1. Unlock the dispenser drawer by pressing the Release Lever in

the Prewash compartment. See "Using the Dispenser."

Remove the drawer.

2. Remove the inserts (the siphon from the softener and bleach

compartments and the separator).

3. Wash the parts under running water.

4. Replace the inserts and return the dispenser to the drawer.

Replace inlet hoses after five years of use to reduce the risk of

hose failure. Periodically inspect and replace inlet hoses if

bulges, kinks, cuts, wear or leaks are found.

When replacing your inlet hoses, record the date of replacement.

Install and store your washer where it will not freeze. Because

some water may stay in the hoses, freezing can damage your

washer. If storing or moving your washer during freezing weather,

winterize it.

Non-use or vacation care:

Operate your washer only when you are at home. If you will be on

vacation or not using your washer for an extended period of time,

you should:

• Unplug washer or disconnect power.

• Turn off the water supply to the washer. This helps avoid

accidental flooding (due to a water pressure surge) while you

are away.

• Slightly open door to provide ventilation.

To winterize washer:

1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.

2. Run washer on a DRAIN/SPIN cycle.

3. Unplug washer or disconnect power.

4. Shut off both water faucets.

5. Disconnect water inlet hoses from faucets and drain.

To use washer again:

1. Flush water pipes.

2. Reconnect water inlet hoses to faucets.

3. Turn on both water faucets.

4. Plug in washer or reconnect power.

5. Run the washer through the NORMAL/CASUAL cycle with

1Athe normal recommended amount of detergent to clean out

antifreeze.

To transport the washer:.

1. If washer will be moved during freezing weather, put in 1 qt

(1 L) of R.V.-type antifreeze in the drum. Run washer on a

DRAIN/SPIN cycle.

2. Unplug washer or disconnect power.

3. Disconnect the drain hose from the drain system and attach

to rear panel clips.

4. Shut off both water faucets.

5. Disconnect the water inlet hoses from faucets, then drain the

hoses and clip them to the rear panel of the washer.

6. IMPORTANT: Call service. Do not reuse transport bolts. Unit

must be transported in the upright position.

Reinstalling the washer

1. Follow the "Installation Instructions" to locate, level and

connect the washer.

2. Run the washer through the NORMAL!CASUAL cycle with

V4the normal recommended amount of detergent to clean the

washer and remove the antifreeze, if used.

TROUBLESHOOTING

First try the solutions suggested here to possibly avoid the cost of a service call...

Washer displaying code message and tone sounds Washer stops

"FH" (Water Inlet Problem--no water or insufficient water

supply)

Select PAUSE/CANCEL twice to cancel the cycle. Unplug

washer or disconnect power.

Check the following:

Are water faucets completely turned on?

Are screens at inlet hose connection to washer clogged?

Are water inlet hoses kinked?

Check the following:

Is the power cord plugged into a grounded 3 prong outlet?

Is there power at the plug?

Check electrical source or call electrician.

Has a fuse blown or has the circuit breaker tripped?

If problem continues, call electrician.

Are you using an extension cord?

Do not use an extension cord.

Are water inlet hoses frozen?

Plug in washer or reconnect power. Re-select cycle and press

START. If the problem remains, call for service.

"F02" (Drain Problem)

Select PAUSE/CANCEL twice to cancel the cycle. Unplug

washer or disconnect power.

Check the following:

Is the drain hose kinked?

Is the drain hose frozen?

Washer won't drain or spin

• Is the drain hose clogged, or the end of the drain hose

more than 96 in. (2.4 m) above the floor?

• Is your voltage low?

Check electrical source or call electrician. Do not use an

extension cord.

• Is the "SUB" routine active?

Cycle will complete once extra suds are removed.

Is the drain hose clogged?

Is the drain hose more than 96 in. (2.4 m) above the floor?

"SUD" (Suds Routine)

When excessive suds are detected, a suds routine

automatically starts. This routine removes extra suds and

assures proper rinsing of your garments. "SUD" is displayed

during rinsing and at the end of the cycle to inform you that

Suds Routine was activated. To avoid excessive sudsing,

reduce detergent amounts or use HE detergents.

"F" Variables [F4 to F16] (Electrical Problem)

Select PAUSE/CANCEL twice to cancel the cycle. Select

DRAIN/SPIN if there is excessive water in the washer.

Re-select cycle and press START. If the problem remains, call

for service.

Washer won't start

• Checkthe following:

Is the power cord plugged into a grounded 3 prong outlet?

Is the washer door firmly shut?

Has a cycle been selected, but START has not been selected

and held for one second?

Was the door open after completion of last cycle?

• Is the load balanced?

A single or bulky item may cause imbalance. Add more items

or redistribute the load.

Washer makes noise or vibrates

Is the washer level?

The washer must be level. The four feet should be properly

installed, and the nuts should be tightened against the

washer cabinet.

As water is drained from the washer, you may hear air being

pulled through the pump. This happens during the end of

draining. It is normal.

Are you washing items with metal snaps, buckles or zippers?

You may hear metal items touching the washer drum. This is

normal.

Is washer installed on a sturdy and solid floor?

Refer to the "Installation Instructions" for flooring

requirements. Noise and vibration may be reduced by placing

a piece of 3Ain. (19.1 mm) plywood underneath your washer.

The plywood may extend underneath both washer and dryer

to keep them at equal heights.

Water near washer

Washer won't fill, wash or rinse

• Checkthe following:

Is the power cord plugged into a grounded 3 prong outlet?

Is there power at the plug? Check electrical source or call

electrician.

Are the hot and cold water faucets turned on?

Is the water inlet hose kinked?

Are the water inlet valve screens clogged?

Check household plumbing for leaks.

Dispensers clogged or leaking

Are the laundry products in the correct dispenser

compartment?

Add the correct amounts of detergent, fabric softener or liquid

chlorine bleach to the correct compartments. Add powdered or

color-safe bleach to the Main Wash compartment.

Is the detergent separator in the correct position?

Separator should be in the front position when using liquid

detergent and in the back position when using powdered

detergent.

Load too wet

• Did you use the right cycle for the load being washed?

Select a cycle with a higher spin speed.

Did you wash a single item or bulky items or have you

overloaded the washer?

A single item, bulky items, or overloading may cause

imbalance. Add items or try to evenly distribute your wet

laundry in the drum, and start a DRAIN/SPIN cycle. Ifthe

laundry is still wet, take half of the load out of the washer and

try again.

Residue or linton load

• Did you add detergent to the dispenser?

For best results, add detergent to the detergent

compartment. Do not add detergent to the washer drum.

• Did you sort properly?

Sort lint givers (towels, chenille) from lint takers (corduroy,

synthetics). Also sort by color.

Did you overload the washer?

Do not overload the washer. The washer can be fully loaded,

but not tightly packed. The wash load must be balanced. Lint

can be trapped in the load if overloaded.

• Checkthe following:

Was paper or tissue left in pockets?

• Did you use enough detergent?

Follow manufacturer's directions. Use enough detergent to

hold the lint in the water.

• Is your water colder than 70°F (21°0)?

Wash water colder than 70°F (21°C) may not completely

dissolve the detergent.

Are you using a low speed wash cycle?

Powdered detergents may not dissolve well in a slow speed

cycle. For best results, use liquid detergent for slow speed

cycles like Delicate, Silk, Wool and Ultra Handwash.

Stains on load

• Did you add detergent to the dispenser?

For best results, add detergent to the detergent

compartment. Do not add detergent to the washer drum.

Did you use enough detergent?

Use enough detergent to remove soil and hold it in suspension.

For best performance, use a High Efficiency detergent.

Follow manufacturer's recommendations for the type of load

you are washing.

• Is there above average iron (rust) in water?

You may need to install an iron filter.

• Did you properly sort the load?

Sort dark clothes from whites and lights.

• Did you unload the washer promptly?

To avoid dye transfer, unload the washer as soon as it stops.

• Did you use a fabric softener dispensing ball?

Dispensing balls will not operate correctly with this washer.

Add liquid fabric softener to the fabric softener compartment.

• Did you use powdered detergent in a low speed cycle?

Consider using liquid detergent.

• Did you use Express Wash on a large load?

For best results, use Express Wash for small, lightly soiled

loads.

Load is wrinkled

Did you unload the washer promptly?

Unload the washer as soon as it stops.

Did you use the right cycle for the load being washed?

Use the Delicate cycle or another cycle with a low spin speed

to reduce wrinkling.

Did you overload the washer?

The wash load must be balanced and not overloaded. Loads

should tumble freely during washing.

Gray whites, dingy colors

• Did you properly sort the load?

Dye transfer can occur when mixing whites and colors in a

load. Sort dark clothes from whites and lights.

Was the wash temperature too low?

Use hot or warm washes if safe for the fabric load. Make sure

your hot water system is adequate to provide a hot water

wash.

Did you use enough detergent, or do you have hard

water?

Use more detergent for washing heavy soils in cold or hard

water.

Cycle too long

Did you choose the Sanitary cycle or Stain Treat option?

In both cases the heater will be activated to provide

maximum cleaning performance. Additional time will be

added to the regular cycle to heat the water. This additional

time will depend on the load size and the hot water inlet

temperature.

Is "SUD" shown in the display?

Excessive sudsing has been detected and a suds routine has

been started to destroy excessive suds. This routine will add

time to the original cycle.

Did the load cause imbalance?

When too much imbalance occurs, an imbalance routine will

start to redistribute the load. This routine will add time to your

original cycle.

Door locked at end of wash cycle

Did all of the water drain out of the washer during the

spin?

Select DRAIN/SPIN to remove any water remaining in the

washer. The washer door will unlock at the end of the drain.

La page charge ...

Kenmore Elite 11042932200 Le manuel du propriétaire

Marque: Kenmore Elite

Modèle: 11042932200

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore Elite 11042932200 Owner's manual
español: Kenmore Elite 11042932200 El manual del propietario

Kenmore Elite 11042932200 Le manuel du propriétaire

Kenmore Elite 11042932200 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents