TEAC UD-504 Le manuel du propriétaire

D01252820A

Z

UD-503

USB D/A Converter

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

ENGLISH

FRANÇAIS

ESPAÑOL

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or ground-

ing-type plug. A polarized plug has two blades with one wider

than the other. A grounding type plug has two blades and a

third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the obso-

lete outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the man-

ufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume)

from earphones or headphones can cause hearing loss.

EN

3

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

V

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and

negative (^) orientations.

o Use batteries of the same type. Never use different types of bat-

teries together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batter-

ies together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The

batteries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

The nameplate is located on the bottom of the unit as shown below.

Front side

Nameplate

“DSD” is a registered trademark.

Windows is either registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

Mac, Mac OS and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.

Other company names and product names in this document are the trademarks or registered trademarks of their respective owners.

4

IMPORTANT SAFETY INSTRUCTIONS (continued)

Model for USA

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Declaration of Conformity

Responsible party:

TEAC AMERICA, INC.

Address: 1834 Gage Road, Montebello, California, U.S.A.

Telephone number : 1-323-726-0303

This device complies with Part.15 of FCC Rules.

Operation is subject to the following two conditions:

1) This device may not cause interference

2) This device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

DECLARATION OF CONFORMITY

We, TEAC AUDIO EUROPE, Liegnitzer Straße 6, 82194

Gröbenzell, Germany declare in own responsibility,

the TEAC product described in this manual is in

compliance with the corresponding technical standards.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

For European Customers

Disposal of electrical and electronic equipment

and batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/

accumulators should be disposed of separately from the

municipal waste stream via collection facilities designated by

the government or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable

resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb

, Hg,

Cd

EN

5

Contents

Check to be sure the box contains all the included items shown

below.

Please contact the store where you purchased this unit if any

of these items are missing or have been damaged during

transportation.

Power cord × 1

RCA conversion (RCA to mini plug) cable × 1

Remote control (RC-1319) × 1

Batteries for remote control (AAA) × 2

Owner’s manual (this document) × 1

o Keep this manual in a safe place for future reference.

Warranty card × 1 (for users in the USA and Canada only)

o Users in Europe and other countries and regions should see the

back of this document for information about the warranty.

Pads × 3

Thank you for choosing TEAC.

Read this manual carefully to get the best performance from this

unit. After reading it, keep it in a safe place with the warranty card

for future reference.

Included items

IMPORTANT SAFETY INSTRUCTIONS ...............................2

Included items ....................................................5

Before use .........................................................6

Maintenance ......................................................7

Using the TEAC Global Site ......................................... 7

Product registration ...............................................7

Using the remote control ..........................................7

Connections (rear panel) ...........................................8

Connections (front panel) .........................................10

Connecting headphones .........................................11

Names and functions of parts (main unit) .........................12

Names and functions of parts (remote control) ....................13

Display ...........................................................14

Upconversion function ...........................................15

Basic operation ...................................................16

Settings ..........................................................17

Playing back music on a computer ................................20

Restoring default settings .........................................21

Troubleshooting ..................................................22

Specifications .....................................................23

6

V

Placement precautions

o Do not install this unit in a location that could become hot.

This includes places that are exposed to direct sunlight or near

a radiator, heater, stove or other heating equipment. Moreover,

do not place it on top of an amplifier or other equipment that

generates heat. Doing so could cause discoloration, deformation

or malfunction.

o Avoid locations that are extremely cold or exposed to excessive

humidity or dust.

o When installing this unit, leave a little space (at least 3 cm or 8")

between it and walls and other devices in order to allow good

heat dissipation. If you put it in a rack, for example, leave at least

5 cm (2") open above it and at least 10 cm (4") open behind it.

Failure to provide these gaps could cause heat to build up inside

and result in fire.

o Place the unit in a stable location near the audio system that you

will use with it.

o DO NOT place anything, not even CDs, CD-Rs, LP records or cas-

sette tapes, on top of the units. Doing so could cause damage.

o The voltage supplied to the unit should match the voltage

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

o Do not move the unit during use.

o Do not open the body of the unit because this could result in

damage to the circuitry or cause electric shock. If a foreign object

should enter the unit, contact your dealer.

o When removing the power plug from the wall outlet, always pull

directly on the plug; never yank on the cord.

Before use

Note about pinpoint feet

High-precision metal pinpoint feet are attached firmly to the bot-

tom plate of this unit.

The stands for these feet are loose, but when the unit is placed in

position, it is supported by these pinpoint feet, which will effectively

disperse vibrations.

Chassis

Pinpoint foot (metal)

Foot-stand (metal)

Screws that attach foot-stand

o Apply the included pads to the bottoms of the foot-stands to

avoid scratching the surface where the unit is placed.

EN

7

Using the remote control

Precautions for use

V

Misuse of batteries could cause them to rupture or

leak, which might result in fire, injury or the stain-

ing of nearby materials. Please carefully read and

observe the precautions on page 3.

o When using the remote control, point it toward the remote con-

trol signal receiver on the main unit from a distance of 5 m (16 ft)

or less. Do not place obstructions between the main unit and the

remote control.

o The remote control might not work if the remote control signal

receiver on the unit is exposed to direct sunlight or bright light. If

this occurs, try moving the unit.

o Beware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by

infrared rays.

Installing batteries

Remove the cover from the back of the remote control and insert

two AAA batteries with their ¥/^ ends oriented in the case as

shown. Replace the cover.

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

Maintenance

Wipe dirt from the top cover and other panel surfaces using a

soft cloth that has been slightly dampened with a diluted neutral

cleanser.

Do not wipe with chemical cleaning cloths, thinner or other chemi-

cal agents. Doing so could damage the surface.

V

For your safety, disconnect the power cord from

the socket before cleaning.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site.

2) In the TEAC Downloads section, click the desired language to

open the Downloads website page for that language.

NOTE

If the desired language does not appear, click Other Languages.

3) Click the “Search by Model Name” section to open the Downloads

page for that product. (Users in Europe should click the product

name in the “Products” section instead.)

4) Select and download the updates that are needed.

Product registration

Customers in the USA, please visit the following TEAC website to

register your TEAC product online.

http://audio.teac.com/support/registration/

8

Connections (rear panel)

LRLR

LR

A B

G

C D

FE

Analog audio output

device

Device that outputs

clock signal

Digital audio output

device

Digital audio output

device

Audio output

(LINE OUT, etc.)

CLOCK SYNC OUT

DIGITAL OUT

(COAXIAL)

DIGITAL OUT

(OPTICAL)

RCA audio cables

RCA coaxial digital cable

50Ω BNC coaxial cable

Optical digital cable

RCA audio cables

XLR cables

USB cable

Audio input

(LINE IN, etc.)

Stereo amplifier or

powered speakers

Computer

c

Wall outlet

Included power cord

Connect cables for the

pair set for line output

(page 19).

Sound will only be output

from the selected pair.

If headphones are

connected, sound will

stop being output from

the rear panel connectors.

The polarity of the XLR

connectors can be set so

that either 2 or 3 is HOT

(page 19).

Connect a set of

cables of one type

or the other.

If using a Windows OS,

install the dedicated driver

on the computer before

connecting this unit to it

(page 20).

EN

9

A

Analog audio input connectors (LINE IN)

Use these to input stereo analog audio. Connect the audio

output connectors of a cassette deck, CD player or other audio

output equipment to these.

Use commercially-available RCA audio cables for

connections.

Connect this unit's R input connector to the R output connec-

tor of the audio output device, and this unit's L input connector

to the L output connector of the other device.

White (L)

Red (R)

White (L)

Red (R)

B

CLOCK SYNC input connector (10MHz IN)

Input a synchronization signal (clock sync) here.

To input a 10MHz oscillator signal (sine wave output), connect

the oscillator output here.

o Use a commercially-available BNC coaxial cable (50 Ω) for

connection.

o Clock sync is possible when the input source is USB.

C

RCA COAXIAL digital audio input connector

Use this to input digital audio. Connect the coaxial digital audio

output connector of a digital audio device to it.

Use a commercially-available RCA coaxial digital cable

for connection.

D

OPTICAL digital audio input connector

Use this to input digital audio. Connect the optical digital audio

output connector of a digital audio device to it.

Use a commercially-available optical digital cable for connection.

E

Analog audio output connectors (LINE OUT)

These output 2 channels of analog audio. Connect these XLR or

RCA connectors to a stereo amplifier or powered speakers.

Use commercially available cables for connections.

XLR: balanced XLR cables

RCA: RCA audio cables

Connect this unit's R connector to the R connector of the

amplifier and its Lconnector to the L connector of the amplifier.

o See“Line output” on page 19 for analog output settings.

F

USB port

Use to input digital audio from a computer. Connect it to a

computer's USB port.

Use a commercially-available USB2.0 cable (A-B type) for

this connection.

ATTENTION

Before connecting a computer that is running a Windows OS, you

must install the dedicated driver on the computer (page 20).

Proper connection is not possible with a computer that does

not have this driver installed.

G

Power inlet (~IN)

Insert the included power cord here.

After completing all other connections, insert the power plug

into a power outlet.

V

Use only the included power cord. Use of other

power cords could result in fire or electric shock.

Unplug the cord from the outlet when not using

the unit for a long time.

V

Complete all other connections before turning

the unit on.

o Carefully read the manuals of the devices that you are connect-

ing and follow their instructions when making connections.

o Do not bundle connecting cables with power cords. Doing so

could cause noise.

o Connect all plugs completely.

10

Connections (front panel)

Digital audio input (OPT/COAX IN)

This input connector can be used for both optical (OPT) and coaxial

(COAX) connections.

Optical (OPT) connection

Use a commercially-available optical cable with a mini plug.

To enable this input, turn the INPUT SELECTOR knob to select OPTf.

o The “f” indicates the front panel.

Optical mini plug

Coaxial (COAX) connection

Use the included RCA conversion cable and a commercially-

available RCA coaxial digital cable.

To enable this input, turn the INPUT SELECTOR knob to select COAXf.

o The “f” indicates the front panel.

RCA conversion cable

RCA coaxial digital cable

EN

11

Connecting headphones

Ordinary headphones (unbalanced drive)

When using unbalanced headphones, set HEADPHONES to STEREO

(page 18).

Connect the headphones to either or both left and right jacks.

o When connecting headphones to both jacks, use headphones

with the same impedance and efficiency.

o Be aware that if you use two pairs of headphones with different

efficiencies at the same time, you will not be able to adjust their

volumes separately.

Balanced headphones

When using balanced headphones, set HEADPHONES to BALANCED

or ACTIVE GND (page 18).

RL

Connect the L headphones plug to the left jack and the R

headphones plug to the right jack.

o The headphones plugs should be standard 6.3mm (1/4") plugs.

Wiring illustration

The following wirings support headphones that use balanced drive.

R

+

–

PHONES

L

+

–

R

+

–

PHONES

L

+

–

Tip(R+)

Ring(R-)

Sleeve(NC)

Tip(L+)

Ring(L-)

Sleeve(NC)

Tip(R+)

Ring(R-)

Sleeve(NC)

Tip(L+)

Ring(L-)

Sleeve(NC)

Twin-core shielded

Single-core shielded

or parallel wiring

Single-core shielded

or parallel wiring

ATTENTION

o Connecting a mono plug will short one side.

o When using twin-core shielded wires, do not connect the shields

to the headphones.

V

CAUTION

While wearing headphones, do not connect or disconnect them or

turn the unit on or off.

Doing so could result in a sudden loud noise that could harm your

hearing.

After connecting headphones to this unit, always set the volume to

minimum (−∞ dB) before putting the headphones on (page 16).

12

Names and functions of parts (main unit)

A

POWER switch

Use to turn the unit on and off.

o If the display is dark even though the POWER switch is set to

ON, the cause is usually one of the following.

• The power is on, but DIMMER (display brightness) is set to

OFF (page 19).

• The automatic power saving function has put the unit into

standby.

• The power cord is disconnected.

To turn the unit on, press the STANDBY/ON button on the

remote control, or set the power switch to OFF once and then

back to ON.

B

CLOCK indicator

This shows the clock synchronization status.

Lit: The unit is synchronized with the clock from the

CLOCK SYNC input connector (10MHz IN).

Blinking: No clock is being input or the unit is not being

synchronized.

Unlit: No clock sync is occurring.

o See page 18 for clock sync settings.

C

Digital audio input (OPT/COAX IN)

Use this to input digital audio.

Optical connection: Use an optical cable with a mini plug.

Coaxial connection: Use the included RCA conversion cable.

D

INPUT SELECTOR knob

Use to select the input source.

Use to change setting values when a menu item is shown.

Press to use as an ENTER button.

Turn when the menu is open to change the item shown or the

setting value.

E

MENU button

Press to enter setting mode (page 17).

Press when in setting mode to return to the previous screen.

F

Remote control signal receiver

This receives signals from the remote control. When operating

the remote control, point it at the remote control signal receiver.

G

PHONES jacks

Connect headphones with a standard 6.3mm (1/4") stereo plug

here (page 11).

o If headphones are connected to this unit, audio will not be

output from the analog audio outputs on the rear panel.

H

Display

This display shows information about the audio playing back

and menu screens.

I

VOLUME knob

Use to adjust the headphones output volume. Turn right to

increase and left to decrease the volume.

o To enable adjustment of this unit's analog audio output

volume, set LINE OUT LEVEL to VARIABLE (“Line output level”

on page 19). This will enable adjustment of the analog

output level using this VOLUME knob.

o Volume settings are retained separately for analog audio

output and headphone output.

A B C D E F G H I

EN

13

Names and functions of parts (remote control)

a

STANDBY/ON button

Press to put the unit into standby mode or turn it on.

b

INPUT buttons

Use to select the playback source.

c

UPCONVERT button

Use to change the upconversion setting.

d

FILTER button

Use to change the filter setting.

This changes the filter according to the input (PCM or DSD).

e

HEADPHONE button

Use to change the headphone type.

f

MUTE button

Press to minimize the volume.

g

DIMMER button

Use to adjust the brightness of the main unit's display.

h

MENU button

Press to enter setting mode (page 17).

Press when in setting mode to return to the previous screen.

i

ENTER button

Press to confirm the selected item.

j

Up/down (k/j) buttons

Use to select setting items.

k

VOLUME (+/−) buttons

Use these buttons to adjust the volume.

e

d

c

a

f

b

g

h

i

j

k

When the main unit and the remote control both have buttons

with the same functions, this manual explains how to use one of

the buttons. The other corresponding button can be used in the

same manner.

14

Display

When on

WELCOME

c

TEAC

UD-503

After the above messages appear, the input source will be shown on

the display.

Input source information display

The input source information display will appear after turning the

unit on as well as when about 10 seconds pass without operation

when a setting screen is open.

Display example

When headphones are not connected and LINE OUT LEVEL is

set to FIX or OFF

USB ORG DF OFF

PCM 44.1kHz

Input source name

Audio data

processing method

Digital filter setting

Input signal status

o Turning the VOLUME knob will not change the volume.

When headphones are connected or LINE OUT LEVEL is set to

VARIABLE

USB ORG DF OFF

PCM 44k -41.5dB

Input signal status Volume

o Turning the VOLUME knob will change the volume, and the vol-

ume will appear to the right of the input signal status.

Input source name

This shows the name of the selected source.

The names shown on the display correspond to the selected con-

nectors as follows.

USB

USB port

COAXf

Coaxial connection with the digital audio input (OPT/COAX IN)

on the front panel

COAX

RCA COAXIAL digital audio input connector on the rear panel

OPTf

Optical connection with the digital audio input (OPT/COAX IN)

on the front panel

OPT

OPTICAL digital audio input connector on the rear panel

LINE

Analog audio input connectors (LINE IN) on the rear panel

Audio data processing methods

ORG

The original input signal is sent directly to the D/A converter

without upconversion.

2Fs

4Fs

8Fs

DSD

The upconversion shown will be used (page 18).

DoP

DSD signal is received by DoP (DSD over PCM) method.

Digital filter setting

This shows the digital filter setting (page 18).

EN

15

Input signal status

This shows the input source signal status.

UNLOCK!

The unit cannot synchronize with the input signal.

NOT AUDIO!

A signal with a format that cannot be played is being received.

UNCONNECTED!

The input source is USB, but no USB cable is connected to the unit.

READY

The input source is USB, but no audio signal is being received.

ANALOG

The input source is the analog audio inputs.

PCM 32kHz

PCM 44.1kHz

PCM 48kHz

PCM 88.2kHz

PCM 96kHz

PCM 128kHz

PCM 176.4kHz

PCM 192kHz

PCM 256kHz

PCM 352.8kHz

PCM 384kHz

DSD 2.8MHz

DSD 5.6MHz

DSD 11.2MHz

These show the input signal type and sampling frequency.

Volume display

The volume setting will be shown when you turn this unit's VOLUME

knob.

Display example

Volume -

60

.0dB

Upconversion function

You can use the upconversion function with digital audio input

(OPT, COAX) and USB input (page 18).

The relationships between input sampling frequencies and sam-

pling frequencies after upconversion are as follows.

Input source Upconversion setting

Digital audio

input

USB OFF 2Fs 4Fs 8Fs DSD

Input sampling

frequency

Sampling frequency after upconversion

[kHz] [kHz] [MHz]

32 − 32 64 128 256 8.0

44.1 44.1 44.1 88.2 176.4 352.8 11.2

88.2 88.2 88.2 88.2 176.4 352.8 11.2

176.4 176.4 176.4 176.4 176.4 352.8 11.2

− 352.8 352.8 352.8 352.8 352.8 11.2

48 48 48 96 192 384 12.2

96 96 96 96 192 384 12.2

192 192 192 192 192 384 12.2

− 384 384 384 384 384 12.2

Values indicated by are unchanged.

16

Basic operation

1 Shift the POWER switch to its ON position to turn

the unit on.

o If a stereo amplifier is connected to this unit, always turn its

power ON very last.

2 Turn the INPUT SELECTOR knob to select the input

source.

The selected source appears on the display.

o You can also use the up and down (k, j) buttons on the

remote control.

o If the input signal is not a digital audio signal or is an audio

signal format that is not supported by this unit, such as

Dolby Digital, DTS or AAC, “NOT AUDIO!” will appear on the

screen and no audio will be output. Set the digital output of

the connected device to PCM audio output.

o To use a computer running a Windows OS to play back

audio files when this unit is set to USB, you must first install a

dedicated driver on the computer before connecting them

(page 20).

o DSD data can only be played back using USB or DoP format

digital input.

3 Operate the playback device.

Refer to the operation manual of that device.

4 Adjust the volume.

When using the line outputs

When LINE OUT LEVEL is set to VARIABLE, turn this unit's VOLUME

knob to adjust the volume.

When LINE OUT LEVEL is set to any other setting, the volume

cannot be adjusted from this unit. Use the stereo amplifier or

other device connected to this unit to adjust the volume.

When headphones are connected to this unit

Turn this unit's VOLUME knob to adjust the volume.

o When this unit's VOLUME knob is enabled, the volume set-

ting will be shown.

EN

17

Settings

1 Press the MENU button to show the setting items.

2 Turn the INPUT SELECTOR knob to show the setting

to be changed.

o You can also use the up and down (k, j) buttons on the

remote control.

The menu items appear in the following order.

HEADPHONES

UPCONVERT

PCM D-FILTER

DSD D-FILTER

CLOCK SYNC

LINE OUT

LINE OUT LEVEL

DIMMER

AUTO POWER SAVE

3 Press the INPUT SELECTOR knob to confirm the

selection.

o You can also press the ENTER button on the remote control.

o The currently set value is shown on the display.

4 Turn the INPUT SELECTOR knob to change the set-

ting value.

o You can also use the up and down (k, j) buttons on the

remote control.

o Press the MENU button to return to setting item selection.

5 When you are done changing settings, press the

MENU button to show the input source status again.

o If you do not do anything for about 10 seconds, the display

will return to showing the input source status.

18

Upconversion

Use to activate the upconversion circuit when receiving PCM format

signals.

o See page 15 for the relationships between input sampling fre-

quencies and sampling frequencies after upconversion.

*UPCONVERT

> OFF

OFF

The original input signal is sent directly to the D/A converter

without upconversion.

2Fs

If the input audio signal is less than 2× a standard sampling fre-

quency (32, 44.1 or 48 kHz), it is upconverted 2× and then sent to

the D/A converter.

4Fs

If the input audio signal is less than 4× a standard sampling fre-

quency (32, 44.1 or 48 kHz), it is upconverted 4× and then sent to

the D/A converter.

8Fs

If the input audio signal is less than 8× a standard sampling fre-

quency (32, 44.1 or 48 kHz), it is upconverted 8× and then sent to

the D/A converter.

DSD

The input source is converted to DSD digital format, and then

sent to the D/A converter.

PCM digital filter

Use to set the digital filter when receiving PCM format signals.

*PCM D-FILTER

> OFF

OFF

The digital filter is disabled.

FIR SHARP

An FIR filter with a steep roll-off is used to sharply cut signals out-

side the audio band.

FIR SLOW

An FIR filter with a slow roll-off is used to gently cut signals out-

side the audio band.

SDLY SHARP

A short delay filter with a steep roll-off is used to sharply cut sig-

nals outside the audio band.

SDLY SLOW

A short delay filter with a slow roll-off is used to gently cut signals

outside the audio band.

o When receiving signals at 352.8 kHz or 384 kHz, the digital filter

will be disabled during playback regardless of this setting.

DSD digital filter

Use to set the digital filter when receiving DSD format signals.

*DSD D-FILTER

> CUTOFF 150kHz

CUTOFF 50kHz

50Hz cutoff frequency

CUTOFF 150kHz

150Hz cutoff frequency

Clock sync

o Clock sync is possible when the input source is USB.

*CLOCK SYNC

> OFF

OFF

No clock sync is used.

ON

This unit's master clock will be synchronized to the 10MHz clock

input through the CLOCK SYNC input connector (10MHz IN).

Headphones settings

*HEADPHONES

> STEREO

Make settings suitable for the headphones being connected (page

11).

STEREO

Unbalanced headphones

BALANCED

Balanced headphones

Balanced headphones are operated with differential drive.

The negative and positive connectors operate with opposite

polarities.

ACTIVE GND

Balanced headphones

The amp drives so that the negative connector of balanced head-

phones is 0 V.

To the headphones, the characteristics of the outputs become

equivalent.

Settings (continued)

EN

19

Line output

*LINE OUT

> RCA

Use to select the connectors that output analog audio.

o Output through both the RCA connectors and the XLR connec-

tors at the same time is not possible.

RCA

Output through the RCA connectors.

XLR2

Output through the XLR connectors with 2: HOT polarity.

XLR3

Output through the XLR connectors with 3: HOT polarity.

Line output level

*LINE OUT LEVEL

> FIX 0dB

Use to select audio level output from the analog audio output con-

nectors (LINE OUT).

FIX 0dB

A maximum of 2 Vrms is output. Select this if you want to adjust

the volume using an amplifier.

o No sound will be output if headphones are connected.

FIX +6dB

A maximum of 4 Vrms is output. Select this if you want to adjust

the volume using an amplifier.

o No sound will be output if headphones are connected.

o If the sound distorts, set this to FIX 0dB.

VARIABLE

This will enable adjustment of the analog output level using the

VOLUME knob. Select this if you want to adjust the volume using

this unit.

o No sound will be output if headphones are connected.

OFF

No sound is ever output.

Display brightness

*DIMMER

> DIMMER 3

DIMMER 3

Ordinary brightness

DIMMER 2

Slightly dim

DIMMER 1

Even dimmer

OFF

Display off

o The display stays unlit even when the unit is on.

Automatic power saving function

This unit has an automatic power saving function.

o The automatic power saving function is on when the unit is

shipped new from the factory.

*AUTO POWER SAVE

> ON

OFF

The automatic power saving function is disabled.

ON

The unit will automatically enter standby mode if there is no audio

input when the input source is LINE or if no input signal is locked

for about 30 minutes when the input source is anything else.

20

Playing back music on a computer

Installing the driver on a computer

This unit can be connected with computers running the following

operating systems. Operation with other operating systems is not

guaranteed (As of April, 2015).

When using Mac OS

The driver works with the following versions.

OS X Lion (10.7)

OS X Mountain Lion (10.8)

OS X Mavericks (10.9)

OS X Yosemite (10.10)

This unit will run with the standard OS driver, so there is no need to

install a special driver.

When using Windows

The driver works with the following versions.

Windows 7 (32/64-bit)

Windows 8 (32/64-bit)

Windows 8.1 (32/64-bit)

Installing the driver on the computer

In order to play audio files stored on a computer through this unit,

you must install a dedicated driver on that computer beforehand.

Download the dedicated driver from the TEAC Global Site:

TEAC Global Site

http://teac-global.com/

ATTENTION

Install the dedicated driver before connecting the unit with

the computer by USB.

If you connect this unit with a computer before installing the driver,

it will not work properly.

o For instructions about driver installation procedures, access the

Downloads page from the TEAC Global site (http://teac-global.

com/).

o Depending on the combination of hardware and software, proper

operation might not be possible even with the above operating

systems.

About the transmission mode

This unit connects using high-speed asynchronous mode.

The sampling frequencies that can be transmitted are 44.1, 48, 88.2,

96, 176.4, 192, 352.8 and 384 kHz.

When properly connected, you will be able to select “TEAC USB

AUDIO DEVICE” as an audio output from the computer OS.

o In asynchronous mode, the audio data sent from the computer

will be processed using this unit's clock, enabling the amount of

jitter that occurs during data transmission to be reduced.

Downloading playback application TEAC

HR Audio Player

You can download Mac and Windows versions of our free TEAC HR

Audio Player application that supports playback of DSD files from

the TEAC Global Site (http://teac-global.com/).

TEAC HR Audio Player setting note

To play 11.2MHz DSD recordings with TEAC HR Audio Player, open

the Configure window and set the “Decode mode” to “DSD Native.”

To play formats other than 11.2MHz DSD, you can set this to either

“DSD over PCM” or “DSD Native” as you like.

For details, see “Selecting DSD decoding mode” in the TEAC HR

Audio Player Owner’s Manual.

Playing back audio files from a computer

1 Connect this unit to the computer using a USB cable.

USB cable

o Use a cable with a connector that matches that of this unit.

2 Turn the computer on.

o Confirm that the operating system has started properly.

3 Shift the POWER switch to its ON position to turn

the unit on.

La page charge ...

TEAC UD-504 Le manuel du propriétaire

Ce manuel convient également à

TEAC UD-504 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents