universal douglas LRKC24-40L8xx-U Manuel utilisateur

Marque: universal douglas

Modèle: LRKC24-40L8xx-U

Taper: Manuel utilisateur

www.universaldouglas.com | Rev. 3/14/22Universal Lighting Technologies

INSTALLATION INSTRUCTIONS

Supplied Components

(2) EVERLINE LED Lensed Module/Light Bars

(1) EVERLINE Driver

(1) BT-LRT-B Bluetooth Controller

(1) Black and White Driver Input Extension Wires

(1) Red and Blue Driver Output Extension Wires

(3) Screws supplied per 4’ Light Bar

(2) Driver Screws(Serrated Washer)

(2) Connectors (Orange 3-Position)

(2) Connectors (Red, 2-Position)

(1) Relamp label

Risk of shock. Disconnect power before installation.

DANGER- RISQUE DE CHOC- COUPER L’ALIMENTATION AVANT L’INSTALLATION

Risk of fire or electric shock. LED Retrofit Kit installation requires

knowledge of luminaires electrical systems. If not qualified, do not

attempt installation. Product must be installed in accordance with NEC

or your local electrical code. If you are not familiar with these codes and

requirements, contact a qualified electrician.

ATTENTION- Risque d’incendie ou de choc électrique. L’installationdu kit upgrade

LED exige Ia connaissance des systèmes électriques pour luminaires. Si non qualifié,

ne tentez pas d’installation. Ce produit doit être installé conformément à NEC ou votre

code électrique local. Si vous n’êtes pas familier avec ces codes et ces exigences,

veuillez contacter un électricien qualifié.

Risk of fire or electric shock. To prevent wiring damage or abrasion, do

not expose wires to the edge of sheet metal or any other sharp objects.

ATTENTION- Pour éviter les dégâts de câblage par l’abrasion, ne pas mettre en contact

les fils électriques avec des bords de tôle ou d’autres objets pointus.

Risk of fire or electric shock. Check the existing wiring for damage

before Installing upgrade kit. Do not install if existing wires are damaged.

ATTENTION- Risque d’incendie ou de choc électrique. Vérifier si le câblage existant

n’est pas endommagé avant l’installation du kit upgrade LED. Ne pas installer si des

fils sont endommagés.

Risk of fire or electric shock. Luminaire wiring and electrical parts may

be damaged when drilling for installation of the LED upgrade kit. Check

for enclosed wiring and components.

ATTENTION- Risque d’incendie ou de choc électrique. Câblage électriques peuvent

être endommagés Iors du perçage pour l’installation du kit upgrade LED. Vérifier les

fils et composants.

SUITABLE FOR DRY LOCATIONS.

NOT FOR USE WITH PHASE CUT DIMMERS.

CONVIENT AUX EMPLACEMENTS HUMIDES.

NE PAS UTILISER AVEC GRADATEUR À COUPURE DE PHASE.

Risk of fire or electric shock. Install this kit only in luminaires that have

the construction features and dimensions shown in the photographs and/

or drawings.

ATTENTION- Risque d’incendie ou de choc électrique. lnstallez ce kit seulement dans

les luminaires qui ont les caractéristiques de construction et les dimensions dans les

photographies ou les dessins de Ia page suivante.

Only the holes indicated in the photographs or drawings may be

made or altered as a result of the kit installation. Do not leave any

other holes open in a wiring enclosure or electrical component.

Seulement les trous indiqués dans les photographies ou les dessins peuvent être faits

ou altérés pour l’installation du kit upgrade LED.Ne laissez aucun trou ouvert dans le

compartiment électrique.

THE RETROFITKIT IS ACCEPTEDAS A COMPONENT

OF A LUMINAIREWHERETHESUITABILITYOF THE

COMBINATION SHALL BE DETERMINED

AUTHORITIES HAVING JURISDICTION.

LE NÉCESSAIRE DE MODERNISATION EST ACCEPTÉ

À TITRE DE COMPOSANT D’UN LUMINAIRE

LORSQUE LA PERTINENCE DE LA COMBINAISON

DOIT ËTRE DÉTERMINÉEPAR PAR LES AUTORITÉS

COMPÉTENTES.

DANGER

WARNING

IMPORTANT SAFETY INFORMATION

SAFETY WARNINGS

WARNING

NOTE

UNPACKING THE KIT

Minimum Dimensions

For installation in a2’x4’ luminaire, the following

minimum dimensions apply:

•3” deep pan

•3” wide minimum wiring compartment

•43” minimum length to accommodate 4’ light bars;

LED RETROFIT KIT

14050200 Rev A

www.universaldouglas.com | Rev. 3/14/22Universal Lighting Technologies

INSTALLATION INSTRUCTIONS

LED RETROFIT KIT

SUITABLE LUMINAIRE TYPES

INSTALLATION

MODEL # FLUORESCENT LUMINAIRE TYPES FRENCH TRANSLATION

LRKC24-40L8xx-U

LRKC24-46L8xx-U

LRKC24-60L8xx-U

LRKC24-70L8xx-U

•

2x4 Troffers: Lensed or parabolic, Type IC or Type Non-IC, 40°C max ambient, requires

minimum3“ depth. One kit per 2x4 troffer luminaire.

•

4ft or 8ft vaportight, lensed, minimum 4” depth and 6.5” width, 40°C max ambient, one

kit per vaportight luminaire.

•

4ft or 8ft Striplight:Non-lensed, (minimum wiring compartment dimensions 2.5” depth

and

4” width), 25°C max ambient, one LRKC24 per 4ft, one or two LRKC24per 8ft

striplight

•

2x4 à lentille ou parabolique, Type IC ou de Type NON-IC, température ambiante max.

de 40°C , profondeur min. de 3”

•

Lentille 4 pi. ou 8 pi. étanche à la vapeur avec profondeur min. de 4” et largeur de 6.

5”, température ambiante max. de 40°C

•

4pi ou 8 pi, sans lentille, réglette, (dimensions du compartiment de câblage min., 2.5

“de profond, 4” de large), température ambiante max. de 25°C

Step 1: Disconnect power to the fixture.

Page 2

Step 2: 2x4 luminaire installations, locate latches on

the lens frame and release. Swing lens frame

open and carefully allow lens to hang open as

shown in Figure 1.

NOTE: For vaportights and lensed wraparound

installations, remove lens and set aside.

NOTE: For striplight and non-lensed

wraparound installations go to Step 3.

Step 3: Remove existing linear fluorescent tubes as

shown in Figure 2. Dispose of tubes per local

regulations.

Step 4: Remove wiring compartment to access existing

ballast and set aside. See Figure 3.

Step 5: Cut the leads from the ballast to the socket

housing on both ends of the fixture as shown in

Figure 4.

NOTE: Cut the leads at the socket housing as

short as possible. Push the leads back behind the

lampholder housing or cap any exposed leads.

Lampholders may be removed but require

removal of lampholder leads.

Step 6: Cut the leads from the input power to ballast. See

Figure 5.

NOTE: Cut leads at the ballast leaving as much

length as possible to facilitate installation of the

driver. Strip wires as necessary

Step 7: Remove ballast by unscrewing from the fixture

and dispose of properly per local regulations. See

Figure 6

www.universaldouglas.com | Rev. 3/14/22Universal Lighting Technologies

INSTALLATION INSTRUCTIONS

LED RETROFIT KIT

Step 8:

Step 9:

Step 10 Once positioned, secure light bar to the fixture

with the (6) provided self-tapping screws as

shown in Figure 9. Repeat for additional light

bars. CAUTION: Magnets are temporary for ease

of installation. Do not complete retrofit

installation without securing screws (3 per

lamp).

Step 11: Recommended mounting pattern. See Figure 10.

Locate a flat area on the fixture within the

wiring compartment to mount the driver. The

driver must set flush with the fixture for proper

thermal management. Install the driver where

possible using existing crow’s feet or mounting

holes, and the provided two drill point screws

with serrated heads. Ensure driver is properly

grounded. See Figure 7.

NOTE: For striplight mounting, it is

recommended to minimize exposed blue and

red light bar leads to 3”

Position light bar approximately at the

centerline of existing lamp sockets and centered

between the sockets as shown in Figure 8. For

striplight fixtures, position the lamps on the

wiring compartment cover.

Step 12:

Step 13:

Step 14

Step 15

Step 16

Connect red leads from both light bars to the

loose red lead wire with the supplied orange 3-

position connector by pushing into the open

slot. Repeat for blue leads. See Figure 11.

Connect red and blue lead wires to the correct

driver contacts as indicated on the driver label.

Connect the BT-LRT-B leads to the aux power

and dimming control leads. See Figure 12.

Place the BT-LRT-B in the fixture adjacent to

the light bars and route its harness so that it

can exit out the end of the ballast cover.

Prepare input power leads by stripping 1/4”.

Connect power lead wires to the correctdriver

contactsas indicated on the driver label. See

Figure 13 NOTE: If the existing black and white

lead wires are too short to reach the new

driver position, an extension can be created

using the provided black and white leads and

red two-position connector.

Replace wiring compartment cover. Dress light

bar leads under the cover. Take care not to

pinch red and blue leads between the cover

and fixture.

Place relamp label at a visible location in the

fixture. Close or replace lens and secure

latches or other fastening means.

Wiring Diagram

Fig. 12

Page 3

Fig. 14

Fig. 13

BT-LRT-B Positioning

To allow for optimal Bluetooth communication, the BT-

LRT-B must not be enclosed within or shielded by metal.

Ideal positioning is close to the center of the luminaire.

INSTALLATION INSTRUCTIONS

LED RETROFIT KIT

Step 1: Disconnect power to the fixture. Removelens

and

set aside. Remove and dispose fluorescent lamps

per local regulations.

Step 2: Remove wiring compartment cover/gear tray

cover from the luminaire housing (Figures 2 and

3). Cut the input power leads to the ballast (white

and black) as close as possible leaving as much

length as possible to facilitate installation of the kit

(Figure 4). Cut the leads to the lamp holders as

close to the lamp holder socket housing as possible

(Figure 5). Do not remove lamp holders. Remove

and dispose the existing ballast according to local

regulations.

Step 3: Install the LED driver onto the top side of the

gear tray and connect line and neutral to the input

terminals of the driver and the dimming leads, if provided,

to the dimmingterminals of the driver as shown in the

wiring diagram on page 3 of these instructions and in

accordance with the National Electrical Code (NFPA 70).

Install the light bars to the bottom side of the gear tray and

secure with sheet metal screws. When installing the kit into

a 4ft vaportight the light bars should be installed side to

side. When installing the kit in an 8ft vaportight the light

bars should be installed end to end. When mounting the

light bars tuck the output leads as necessary into the light

bar housing to reduce the amount of slack (Figure 11).

Connect the blue and red leads of the light bars to the

LED driver LED output (red and blue terminals) according

to the wiring diagram shown on page 3 of these

instructions.

www.universaldouglas.com | Rev. 3/14/22Universal Lighting Technologies

INSTALLATION INSTRUCTIONS

LED RETROFIT KIT

Step 4: Mount the parent light bar to the wiring compartment/

gear tray cover and secure with the provided sheet

metal screws. When installing a two light bar

kit (LRKB24 series model), mount the light bars

end-to-end in an 8ft vapor tight housing (Figure 9)

and side by side in a 4ft vapor tight housing (Figure

10). When mounting the light bars end-to-end,

tuck as much of the output leads as necessary into

the light bar housing channel (Figure 11) before

mounting the light bar to the wiring compartment/

gear tray cover to reduce the amount of slack

(Figure 12).

Step 5: Place wiring compartment cover/gear tray cover

with attached light bars back onto luminaire housing

and secure in place. Place lens back onto the fixture

housing and secure in place with the luminaire’s

latches.

Fig. 14

www.universaldouglas.com | Rev. 3/14/22Universal Lighting Technologies

universal douglas LRKC24-40L8xx-U Manuel utilisateur

Marque: universal douglas

Modèle: LRKC24-40L8xx-U

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: universal douglas LRKC24-40L8xx-U User manual

universal douglas LRKC24-40L8xx-U Manuel utilisateur

universal douglas LRKC24-40L8xx-U Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents